Johnson Controls GG9S040A08MP11, GG9S080B12MP11, GG9S060A10MP11, GG9S060B12MP11, GG9S080C16MP11 Technical Manual

95.5% SINGLE STAGE
GAS-FIRED RESIDENTIAL
MULTI-POSITION GAS FURNACES

MODELS: GG9S

NA TURAL GAS
40 - 130 MBH INPUT

Due to continuous product improvement, specifications
are subject to change without notice.

Visit us on the web at www.york.com
Additional rating information can be found at

www.ahridirectory.org

WARRANTY

Lifetime limited warranty on both heat exchangers to the orig­inal purchaser; a 20-year limited warranty from original instal­lation date to subsequent purchaser.

10-year warranty on the heat exchanger in commercial appli­cations.

Standard 5-year limited Parts warranty.

TECHNICAL
GUIDE

TECHNICAL
GUIDE

FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE

400995-UTG-D-0210

DESCRIPTION

These compact units employ induced combustion, reliable hot
surface ignition and high heat transfer aluminized tubular heat
exchangers. The units are factory shipped for installation in
upflow or horizontal applications and may be converted for
downflow applications.

These furnaces are designed for residential installation in a
basement, closet, alcove, attic, recreation room or garage and
are also ideal for commercial applications. All units are factory
assembled, wired and tested to assure safe dependable and
economical installation and operation.

These units are Category IV listed and may be vented either
through side wall or roof applications using approved plastic
combustion air and vent piping.

FEATURES

• Easily applied in upflow, horizontal left or right, or downflow
installation with minimal conversion necessary.

• Compact, easy to install, ideal height 33" tall cabinet.

• Blower-off delay for cooling SEER improvement.

• Easy access to controls to connect power/control wiring.

• Built-in, high level self diagnostics with fault code displays
standard on integrated control module for reliable operation.

• Low unit amp requirement for easy replacement application.

• Single wire twinning or staging feature available.

• All models are convertable to use propane (LP) gas.

• Electronic Hot Surface Ignition saves fuel cost with
increased dependability and reliability.

• 100% shut off main gas valve for extra safety.

• 4 speed, direct drive PSC motor.

• 24V, 40 VA control transformer and blower relay supplied for
add-on cooling.

• Hi-tech tubular aluminized steel primary heat exchanger.

• Secondary heat exchanger made of corrosion resistant
stainless steel materials.

• Timed on, adjustable off blower capability for maximum com­fort.

• Blower door safety switch.

• Solid removable bottom panel allows easy conversion.

• Airflow leakage less than 1% of nominal airflow at duct­blaster conditions.

• No knockouts to deal with, making installation easier.

• Movable duct connector flanges for application flexibility.

• Quiet inducer operation.

• Inducer rotates for easy conversion of venting options.

• Fully supported blower assembly for easy access and
removal of blower.

• External air filters used for maximum flexibility in meeting
customers IAQ needs.

• Protection included from air intake, exhaust vent, or conden­sate blockage.

• Venting applications - may be installed as either 2-pipe
(sealed combustion) or single-pipe vent (using indoor com­bustion air).

• No special vent termination required.

• 1/4 turn knobs provided for easy door removal.

• Internal condensate trap design (patent pending) provides
condensate management options, easy visual operation,
and is self-priming to prevent nuisance problems.

400995-UTG-D-0210

FRONT

33

A

LEFT SIDE

Combustion Air Inlet

Condensate Drain
(Downflow)

Vent Outlet

Thermostat
Wiring

28.5”

Gas Pipe
Entry

Electrical
Entry

Condensate
Drain

Thermostat
Wiring

RIGHT SIDE

Vent Outlet

Condensate Drain
(Downflow)

14”

1”

1.5”

23”

Combustion Air Inlet

Gas Pipe
Entry

Electrical
Entry

Condensate
Drain

Optional Return Air
Cutout (Either side)

29.5”

C

SUPPLY END

.56”

.56”

20”

B

3”

23.8”

.56”

Combustion
Air Inlet

Vent
Outlet

RETURN END

B

24.25”

Cabinet & Duct Dimensions

Models

Nominal

CFM (m

3

/min)

Cabinet

Size

Cabinet Dimensions (Inches)

ABC Lbs

GG9S040A08MP11 800 A 14 1/2 13 3/8 11 3/4 113
GG9S060A10MP11 1000 A 14 1/2 13 3/8 11 3/4 118
GG9S060B12MP11 1200 B 17 1/2 16 3/8 13 1/4 122

GG9S080B12MP11 1200 B 17 1/2 16 3/8 14 3/4 126
GG9S080C16MP11 1600 C 21 19 7/8 16 1/2 136
GG9S080C22MP11 2200 C 21 19 7/8 16 1/2 139
GG9S100C16MP11 1600 C 21 19 7/8 18 1/4 142
GG9S100C20MP11 2000 C 21 19 7/8 18 1/4 145
GG9S120D16MP11 1600 D 24 1/2 23 3/8 21 3/4 153
GG9S120D20MP11 2000 D 24 1/2 23 3/8 21 3/4 156
GG9S130D20MP11 2000 D 24 1/2 23 3/8 No Hole 160

Ratings & Physical / Electrical Data

Models

GG9S040A08MP11 40 38 95.5 30-60 160 1/3 4.8 11x8 15 8.0 14
GG9S060A10MP11 60 57 95.5 30-60 160 1/2 7.1 11x8 15 10.0 14
GG9S060B12MP11 60 57 95.5 30-60 160 1/2 7.1 11x8 15 10.0 14
GG9S080B12MP11 80 76 95.5 35-65 165 1/2 7.1 11x8 15 10.0 14
GG9S080C16MP11 80 76 95.5 35-65 165 3/4 8.8 11x10 15 11.5 14
GG9S080C22MP11 80 76 95.5 35-65 165 1 14.5 11x11 20 17.0 12

Input Output

MBH MBH °F °F HP Amps

AFUE

%

Air Temp.

Rise

Max. Outlet

Air Temp

Blower

GG9S100C16MP11 100 95 95.5 35-65 165 3/4 8.8 11x10 15 11.5 14

Blower

Size

Over-Current

Max

Protect

Total Unit

GG9S100C20MP11 100 95 95.5 35-65 165 1 14.5 11x11 20 17.0 12
GG9S120D16MP11 120 114 95.5 40-70 170 3/4 8.8 11x10 15 11.5 14
GG9S120D20MP11 120 114 95.5 35-65 165 1 14.5 11x11 20 17.0 12
GG9S130D20MP11 130 123.5 95.5 45-75 175 1 14.5 11x11 20 17.0 12

Annual Fuel Utilization Efficiency (AFUE) numbers are determined in accordance with DOE Test procedures.
Wire size and over current protection must comply with the National Electrical Code (NFPA-70-latest edition) and all local codes.
The furnace shall be installed so that the electrical components are protected from water.

2 Johnson Controls Unitary Products

Approximate

Operating Weights

Min. wire Size

Amps

(awg) @ 75 ft

one way