Page 1
Toronto Office Chair
Stock number: 816 33801
H85.5/95.5 W59 D61 cm
Page 2
Thank you for purchasing the Toronto Office Chair. Please read the instructions and warnings carefully before
use, to ensure safe and satisfactory operation of this product.
At John Lewis, we are committed to making as great products as possible.
From our in-house Design Team, to our buyers, we work together to bring great design to life.
Our expert product technologists work collaboratively with our buyers and suppliers to assure the legality,
safety and quality of the product we sell.
We are all committed to designing and developing products to the highest industry standards.
We hope you are happy with your product and welcome any feedback or comments you may have.
The John Lewis Team
Tools required
Time to assemble
20 minutes
People to assemble
1
Page 3
Important safety information
Warnings
The product should only be used on firm ,level ground.
Keep small parts out of reach of children.
Ensure the product is fully assembled as illustrated before use.
Do's
Check the pack and make sure you have all the parts listed.
Check all screws or bolts are tightened and inspect regularly.
Make sure the legs remain in contact with the ground at all times.
Don'ts
Do not over tighten screws or bolts.
Do not stand on the product.
Do not use power tools to construct as overtightening and panel failure may occur.
1 2 3
475 6
8 9
0
John Lewis
03456 049 049
Autochoice'Furniture'
2
Page 4
Your Chair
1
2
3
4
1
2
3
4
5
Mechanism
Gas lift
Matal base
Castor
DimensionsDescreptionRef
580mm x 590mm x 460mmSeat
170mm x 170mm x 50mm
405mm
590mm x 570mm x 70mm
50mm
5
5
5
5
5
Qty
1
1
1
1
5
Internal dimensions
Chair overall size:
H85.5/95.5 W59 D61 cm
3
Page 5
Fixtures and fittings
Fixtures and fittings
supply (actual size)
Ref Descreption Dimensions
Bolts
A
Fixtures and fittings
supply (not actual size)
Descreption Qty
B
Flat washers
Allen key
C
6mm x 20mm 4
DimensionsRef
18mm
5mm
mm
10 7060504030200
Qty
4
1
4
Page 6
Product assembly
Toronto Office Chair
816 33801
Step
Parts and fittings
3
1
4
5
Warning
Remove the cap from
the gas lift piston before
assembly
3
Step 2
Parts and fittings
2
1
A C
3
5
5
B
2
5
5
4
5
C
A
B
1
5
Page 7
Toronto Office Chair
816 33801
Step 3 Final assembly
Parts and fittings
6
Page 8
Warning:
Never tilt the chair. Ensure the chair is always placed firmly on the ground.
Regularly check leg attachment and retighten screws as necessary.
Do not use chair if legs are unstable. Please check fixings and tighten as required.
M
a
x
1
1
0
k
g
7
Page 9
Care guide
Care and maintenance
Fabric upholstery
Protect your fabric from spillage, sunlight and heat. The fabric may be vacuumed and, if necessary, carefully spotÂcleaned. Spot-cleaning agents should only be used after first testing on a less visible area of the fabric.
Safety Instructions
Never drag furniture when moving it, always lift it.
Periodically check all fixings to ensure none have come loose and re-tighten where necessary.
Please take care when handling or moving the furniture as careless handling may cause damage or injury.
Furniture can be dangerous if incorrectly installed. Assembly should be carried out by a competent person. No
liability will be accepted for damage or injury caused by incorrectly installed or assembled furniture.
Always ensure the feet provided with this product are suitable for your flooring.
Periodically check the position of any foot caps/felt pads used to ensure your floors are protected.
Retain these instructions for future reference.
Your feedback is very important to us and we would love to hear your comments on your new furniture.
Please visit our website to leave a review. Thank you.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Loading...