7mm
7mm
7mm
7mm
User manual
Roman blind
Video instructions
Scan the QR code to link to our online videos
that guide you in getting a perfect t for a
Venetian or Roller blind. Alternatively follow
the link johnlewis.com/blindassembly
Please retain these instructions for future reference.
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
johnlewis.com
Made in China Batch Code :
.Operating the blind
. Care instructions
To prevent serious soiling, you can regularly dust the blind with a feather duster or use a vacuum
cleaneron low power. If there are stains, we would advise that you remove the fabric following the
below steps:
Unhook the cord guides from the stitched safety rings (7a). Then carefully remove the bottom bar
which is tucked into bottom pocket. At the top of the blind , pull the fabric off the Velcro fastener.
We recommend the fabric be sent for professional dry clean only.
To replace (7b) re attach clips and carefully re install bottom bar.
a
b
1
7
To operate the blind pull the chain to lower and raise to desired position.
Thank you for purchasing this Roman Blind. Please read the instructions carefully before use
to ensure safe and satisfactory operation of this product. It is recommended that
this blind should only be installed by persons competent in DIY.
Warnings!
Please read all safety warnings and installation information fully before installation.
Young children can be strangled by loops in pull cords, chains, tapes and inner cords
that operate the product.
To avoid strangulation and entanglement, keep cords out of the reach of young children.
Cords may become wrapped around a child’s neck.
Move beds, cots and furniture away from window covering cords.
Do not tie cords together. Make sure cords do not twist and create a loop.
The safety clips should be positioned high enough to be out of reach of small children
yet accessible to adults.
All safety clips for blinds need to be fixed to a solid surface using a screw and fixing suitable
for the wall or surface material. These items should not be glued or stuck in place.
The head rail shall not be installed less than 1.5m from the floor.
For further information go to: www.makeitsafe.org.uk
Keep out of the reach of young children.
Small parts - choking hazard.
Parts list
Please check the contents:
Mounting brackets 2 x <110cm , 3 x >110cm
Screws and Wall Plugs 5 x <110cm , 7 x >110cm
1 Safety clip
< 90cm: 2 x
> 120cm: 3 x
< 90cm: 5 x
> 120 cm: 7 x
1 x
Please note: Additional fasteners other than those sent with your blind may be required depending
on the mounting surface. Wallboard and plaster require the use of anchors such as expansion or toggle
bolts. Brick, tile or stone need special plugs and drill bits. Remember to always pre-drill holes in wood
to avoid splitting.
1. Positioning the blind
A Inside the recess
Decide on the position of the blind so that it will be clear of any latches and fixtures.
B Outside the recess
Decide on the position of the blind so that it overlaps on both sides equally. At least
5cm.
(a)
(b)
Assembly
2. Fixing the brackets
A. Please ensure that the headrail is installed 1.5meters from the floor.
B. The brackets are designed for face or top fixing to the window frame,
wall, or ceiling.
C. Attach the brackets to the headrail by inserting into the
channel on the reverse.
D. Having decided the positioning of the blind, present it to the desired
position, making sure it is centred and level.
E. Mark the location of each bracket with a pencil.
F. Remove each bracket from the headrail by pressing the locking
tab at the bottom of the bracket.
G. Place each bracket on its location markings and mark through
the desired screw hole positions.
H. Use the screws provided to fix the brackets to wood. For masonry , use
appropriate fixings.
2
3
Top fix
Face fix
(e)
Loading...