JLDV 02
vented tumble dryer
JLLFW 1805
fridge
Instruction manual
2
It is most important that this instruction book should be retained with the appliance for future reference. Should the
appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that
the book is supplied with the appliance in order that the new owner can get to know the functioning of the appliance and
the relevant warnings.
These warnings have been provided in the interest of safety. You MUST read them carefully before installing or using the
appliance.
If you are unsure of the meanings of the these warnings contact the John Lewis branch from which you purchased the
appliance.
Important Safety Information
Installation
Use
Maintenance and Cleaning
Child Safety
D This appliance is heavy. Care should be taken when
moving it.
D Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
D Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.
D Parts which heat up should not be exposed. Whenever
possible, the back of the appliance should be close to a
wall, but leaving the required distance for ventilation, as
stated in the installation instructions
D This appliance should be left for 2 hours after
installation before it is turned on, in order to allow the
refrigerant to settle
D Before switching on the Fridge ensure that the interior
light bulb and cover are in position. Do not connect the
appliance if they are not.
D This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
D Keep all packaging away from children.
D When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with the
remaining cable. Disable the door catch in order to
prevent children from becoming trapped inside while
playing.
D This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs only.
It is not intended for commercial or industrial use.
D Containers with flammable gases or liquids can leak at
low temperatures. Do not store any containers with
flammable materials, such as spray cans, fire extinguisher
refill cartridges etc. in the refrigerator or the vicinity of
therefrigeratororanyotherappliance.
D Do not let sharp objects come into contact with
the refrigerating system on the back of and inside
the fridge. If the refrigerating system is punctured, the
fridge will be damaged and foodstuff inside may spoil.
D Do not use electrical appliances inside the Fridge.
D Do not damage the refrigerant circuit.
D Before cleaning, always switch off the appliance and
disconnect from the electrical supply
D W hen unplugging always pull t he plug f rom the mains
socket, do not pull on the cable.
D F or inf or ma tion on maintenance and cleaning your
appliance see page 15 of this Instruction manual.
D This product should only be serviced by an uthorized
engineer and only genuine spare parts should be used.
D Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunction.
Service
3
Environmental Information
Ecological hints
To save energy and help protect the environment, we
recommend that you follow these hints.
D Do not install the appliance close to sources of heat
such as a boiler or radiator.
D Locate the appliance in a well ventilated room and make
sure that any air openings of the appliance are not
obstructed.
D Try to avoid keeping the door open for long periods or
opening the door too frequently as warm air will enter
the cabinet and cause the compressor to switch on
unnecessarily often.
D Ensure there are no obstructions preventing the door
from closing properly .
D After unpacking please dispose of the packaging with due
regard to safety and the environment.
D Materials marked with the symbol
are recyclable.
D Avoid damaging the cooling unit, especially at the rear near
the heat exchanger . Check with your local Council or
Environmental Health Office to see if there are facilities in
your area for recycling this appliance.
D Whentheapplianceistobescrapped,cutoffthepower
supply cable and remove the door , to prevent young
children from being trapped inside.
D This appliance does not contain gases which could damage
the ozone layer, in either its refrigerant circuit or insulation
materials.
War
ning !
A cut off plug inserted into a 13 amp socket is a
serious safety (shock) hazard. Ensure that the cut
off plug is disposed of safely.
The symbol on the product or on its pac
kaging
indicates
that this product may not be treated as household waste.
Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused by inappropriate waste handling of this product.
For more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
4
For the User
Important Safety Information
2
• Installation
Description of the Appliance
5
Before use
10
• When the appliance is not in use 16
The Control Panel
12
Using the fridge
13
Hints and Tips
15
Maintenance and Cleaning
16
• Removing the ventilation grill 16
• Cleaning 16
• Defrostning the fridge 16
• Changing the light bulb 16
Something Not Working
17
Repairs - After Sales Service
18
Spare parts
18
For the Installer
Installation
6
Technical Specifications
6
• Unpacking7
• Installing the cabinet 7
• Door reversal 9
• Climate classification 10
Electrical connection
11
Contents
Guide to using the Instruction Manual
The following symbols will be found in the text to
guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
This appliance complies with the following E.E.C.
Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
• Installation and changing the carbon filter 7
5
6
1
1
1
1
5
5
5
2
3
4
11
7
8
9
10
1. glass shelf
2. quick chill shelf
3. bottle- and can holder
4. grid
5. vegetable/sallad drawer
6. ventilation grill
7. butter compartment
8. door shelf
9. egg holder
10. bottle shelf
11. wine rack
12. air circulation fan
and regulator
8
8
12
1
Description of the Appliance
6
It is dangerous to alter the specifications
or attempt to modify this product in any
way
Care must be taken to ensure that the
appliance does not stand on the electrical
supply cable.
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
DIMENSIONS Width
Height
Depth
595 mm
1800 mm
623 mm
VOLUME 335 l
ELECTRICAL
CONNECTION
Information on the electrical
connection is given on the rating
plate on the inside of the
appliance.
ENERGY CLASS
RA TED POWER
A
70W
NO I SE 40 db
NET WEIGHT 71 kg
Installation
Technical Specifications
7
Unpacking
Remove all packaging before positioning the appliance.
Remove the tape and the transport supports from
D the door sides
D inside the door hinges
D the shelves
Remove the transport support on the glass shelf by pushing
the support forward along the edge of the shelf until it
stops. Take hold of the rear edge of the glass shelf and pull
the shelf and transport support forward until the shelf tilts
and the transport support can be removed. Some models
are fitted with a silencing pad under the fridge. Do not
remove this pad.
Installation and changing the
carbon filter
To maintain the best performance the carbon filter should
be changed once a year with normal usage.
New carbon filters can be purchased from your local Service
Force office.
On delivery the carbon filter is placed in a plastic bag to
secure the length of life of the carbon filter. Remove the bag
and the filter should be placed behind the grill before the
fridge is turned on.
The cover can be opened by simultaneously pressing the
lever on the right of grill (1) and turning the cover outward
(2). The carbon filter is then mounted (3) in the slot found
inthebackofthecover.
The filter should be handled carefully so carbon fragments
don't loosen from the surface.
Installing the cabinet
When two appliances are placed beside each other, the
spacers enclosed in the plastic wrapping should be glued
between the appliances. As shown in the illustration.
Make sure that the power plug is not squashed or
damaged by back of the product.
D A damaged power plug may overheat and cause a fire.
Do not place heavy articles or the product itself on
the power cord.
D there is a risk of a short circuit and fire.
If the power plug socket is loose, do not insert the
power plug.
D there is a risk of electric shock or fire.
If the fridge is placed in a corner and the side with the
hinges facing the wall, the distance between the wall and the
fridge must be at least 230 mm to allow the door to open
enough so that the shelves can be removed.
Check that the drain hose at the rear of the fridge
discharges into the drip tray.
The power plug must be accessible after installation of the
fridge .
1
2
3
8
To obtain the best performance from the fridge,
ensure :
D the fridge is placed in a dry ,cool place and is not exposed
to direct sunlight.
D thefridgeisnotplacedclosetoasourceofheat,e.g.a
cooker or dishwasher.
D the fridge is level. The fridge should not lean against any
wall. If necessary adjust the feet using the adjustment
spanner supplied.
D there is good air circulation around the fridge and that
the air channels below and behind the fridge are not
blocked.Theventilationspacebetweenthefridgeanda
cupboard above must be at least 40mm.
The ventilation space can either be
a) directly above the fridge, or
b) If a cupboard is placed immediately above the
fridge there should be a ventilation gap behind the
cupboard of 50mm deep and at least a 40mm gap
between the top of the cupboard and the ceiling.
If the fridge is placed in a corner and the side with the
hinges facing the wall, the distance between the wall and the
fridge must be at least 230 mm to allow the door to open
enough so that the shelves can be removed.
Check that the drain hose at the rear of the fridge
discharges into the drip tray.
The power plug must be accessible after installation of the
fridge .
50mm
a
)b)
9
Door Re versal
1. Close the fridge and remove the plug from the electrical
socket.
2. Remove the ventilation grille. There is a part on the grille
that can be removed. Remove and reposition it on the
other side.
3. Put the fridge on a wooden board when it is laid down.
Later, when raising the fridge, it will be easier to grip under
the fridge thanks to the board.
4. On the upper part of the fridge. Put the hinge pin on the
other side.
5. On the lower part of the fridge.
a. Unscrew the hinge.
b. Remove the door-closing fittings from the hinge and put
the hinge pin on the other side. Then attach the supplied
door-closing fitting.
6. a. Remove the door-closing fitting from the bottom of the
door.
b. Remove the plastic plug from the corresponding hole on
the other side. Use a screw driver to rock the plug loose.
Then secure the supplied door-closing fitting.
c. Secure the lower hinge.
Remove any play in the door by adjusting the height of the
lower hinge with the supplied spanner. Secure with the lock
nut.
7. Raise the cabinet and replace the ventilation grille.
8. To transfer the handle.
Unscrew the screws. Fit the handle onto the opposite side
by turning it one half circle. Press the supplied plastic plugs
into the holes to which the handle was previously fitted.
9. Put the fridge in position. Check that the appliance is level.
See the section "Installing the fridge".
1
2
3
4
5b
5a
a
b
c
6
8
10
Climate classification
Fridge is placed at a location whose ambient temperature
corresponds to the climate classification*, for which the
appliance is designed.
* See on the rating plate on the inside of the appliance.
The following table shows which ambient temperature is
correct for each climate classification.
Climate
classification
for an ambient
temperature of
+10°C to +32°C
+16°C to +32°C
+18°C to +38°C
+18°C to +43°C
SN
N
ST
T
Position and clean the f r idg e a s explained in t he sect ion
"I nstallation".
C heck t hat t he dr ain hose a t t he rear of the f r idg e
discharges into the drip tray.
Before inserting the power plug into the outlet and
switching on the freezer for the first time, leave it standing
upright for about 4 hours. This time will allow the oil
sufficient time to return to the compressor. Otherwise the
compressor may sustain damage
Before use
9
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST
BE EARTHED.
Should the appliance power supply cable
need to be replaced, this must be carried
out by a Service Force agent (see page 18).
The manufacturer declines any liability
should this safety measure not be
observed.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved BS 1363/A fuse must
be used.
Should the plug need to be replaced for any reason, proceed
as described below. The wires in the mains lead are
coloured in accordance with the following code:
Green and Yellow - Earth
Blue - Neutral
Brown - Live
If you fit your own plug, the colours of the wires in the
mains lead of your appliance may not correspond with the
markings identifying the terminals in your plug.
Proceed as follows:
1. Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter "E" or
the earth symbol or coloured green and yellow.
2. Connect the Blue (neutral) wire to the terminal in the plug
which is marked with the letter "N" or coloured black.
3. Connect the Brown (live) wire to the terminal in the
plug which is marked with the letter "L" or coloured red.
GREEN & YELLOW
BROWN
CORD CLAMP
BLUE
13A
P1041
E
N
L
Electrical connection
4. Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
WARNING:
A cut off plug inserted into a 13 amp
socket is a serious safety (shock)
hazard.
Ensure that the cut off plug is disposed of
safely.
The plug must still be accessible after the
appliance has been installed.
The appliance should not be connected
to the electrical supply by means of an
extension cable
Permanent connection
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap of
3mm between the switch contacts and of a type suitable
for the required load in compliance with the current
electrical regulations.
The switch must not break the yellow and green earth
cable at any point.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance's
rating plate.The rating plate is located on the inside of the
appliance.
12
ACTION
COOL
5
1 2 3 4567
1. Refrigerator power switch
Switches the refrigerator on and off.
2. Temperature display
Shows the average temperature inside the refrigerator.
3. Temperature adjustment
button/thermostat
Used to set the temperature in the refrigerator.
4. QUICK CHILL button
Used to switch the Quick chill feature on and off.
5. Yellow indicator lamp
Lights when Quick chill is operating.
6. Alarm shut-off button
Used to turn the audible alarm off.
7. Red warning lamp
Flashes when one of the alarms in the fridge has been
triggered.
The control panel
13
To start the fridge and setting the
corre ct temperatu re
Switching on:
Switchonthefridgebypressingthepowerswitch.
Setting the temperature
Press the buttons until the desired temperature flashes in
the temperature display (The temperature can be set
between +2°Cand+8°C.)
"+" raises the temperature.
"-" lowers the temperature.
Once set, the temperature display shows "-" until the
temperature inside the fridge reaches +9°Corbelow.
Allow the fridge to run for a period of 24 hours whenever
the temperature setting is changed. This will allow the
temperature to stabilise inside the fridge.
It is not necessary to reset the temperature when the fridge
is switched on after it has been out of use. The thermostat
recalls the previously set temperature.
Temperature inside the fridge
A suitable temperature inside the fridge is approx. +5°C.
Storage temperature in the fridge is even on all of the shelf
levels. The vegetable/sallad drawer which is placed in the
bottom has a temperature of 3-4°C warmer than the
selected temperature setting.
Measuring the temperature
If the temperature is measured using a standard, single
thermometer , this should be put in a glass of water centrally
placed inside the fridge. This will reflect the temperature
inside the food products. Do not place the thermometer
hanging or lying directly on the shelf.
Hints:
D Distribute foodstuffs to allow cold air to
circulate freely between the products.
D Also never put warm (freshly cooked) products
into the fridge. Wait until they have cooled down.
D Cover all foods properly.
Alarms and other featu res
Door open alarm
If the fridge door remains open for more than 5 minutes,
the red warning lamp starts flashing and you will hear an
audible alarm sound.
To switch of f the alarm:
Press the "alarm shut-off button". The red warning lamp
goes out when the door is closed.
Quick chill
This function has two usage areas. One area in connection
with cans / bottles being quickly chilled on the quick chill
shelf, and the other in connection when large amounts of
food at room temperature being placed within the fridge.
ACTION
COOL
5
ACTION
COOL
5
ACTION
COOL
5
Using the fridge
14
Chilling of cans/bottles:
When cans and bottles are placed on the shelf (see under
section; bottle and can holder and Quick chill shelf) the air
regulator should be turned to it's maximum position, then
press the Quick chill button.
This will be indicated in the symbol window with a "C" and
by the yellow lamp being lit.
Chilling of warm groceries:
This function is used in connection with large amounts of
groceries at room temperature being placed in the fridge.
Pressing the Quick chill button starts this function.
This will be indicated in the symbol window with a "C" and
by the yellow lamp being lit.
When this function has been activated forced air will chill
the groceries, and the temperature in the fridge reset to
+2°C. After 6 hours the Quick chill automatically shuts off
and the temperature gradually goes back to its normal
setting. ! It is good practice to switch on the Quick chill
prior to shopping and re-select once the food has been
placed inside.
Carbon filter's function:
The built-in carbon filter means that strong smelling
groceries can be placed near other groceries without
affecting their taste or aroma.
Switching off
Switch off the fridge by pressing the power switch.
Keep the button pressed for approx. 1 second.
Power to the fridge is completely interrupted
only when the power plug is disconnected.
Fridge interior
The shelves and door compartments are removable and can
easily be re-arranged.
Certain shelves must be lifted up by the rear edge to enable
them to be removed.
The lower door compartment and the glass shelf above the
vegetable/sallad drawer must not be moved to an alternative
position. They are required for proper air circulation inside
the fridge.
Shelves with a raised edge should be placed with the raised
edge facing the rear wall of the fridge.
The vegetable drawer has a removable ventilation edging to
increase the circulation of air, retaining humidity in the
drawer and reducing condensation.
The vegetable drawer has two moveable partitions with five
different positions in order to separate different vegetables.
MINMAX
ACTION
COOL
C
ACTION
COOL
5
15
Bottle and can holder
The bottle and can holder is moveable sliding to the left or
right, or front to back to enable a more flexible placement
of cans and bottles in front of the grid. To allow the holder
to be moved easier, when moving sideways, press the shelf
backwards.
During chilling of cans or bottles the holder should be
centrally placed in front of the grid to obtain the best chilling
effect.
The bottle support can be pulled out when chilling larger
bottles.
For a description of this functions start and stop, see under
heading Quick Chill.
Quick chill shelf:
The lower Quick chill shelf can be placed in one of the
upper grooves. To maintain the best performance the shelf
should be placed in the second groove from the top.
Dismantli ng of the bottle- and can
holder.
Take out the Quick Chill shelf with holder from the fridge.
To loosen the holder from the shelf, bend the
hooks/brackets that surround the backside of the shelf.
Food Storage
D To obtain the best results from your appliance,
neither hot foods nor liquids which may evaporate,
should be placed in the larder compartment.
D Remove suspect food from you refrigerator and
clean, refer to cleaning and maintenance.
Hints & Tips
16
Removing the ve ntila tio n grill
Cl eani n g
Clean the freezer at regular intervals. Don't use
detergents, abrasive powders, high perfumed cleaning
products, wax polishes or cleaning products containing
bleach or alcohol when cleaning the product
Disconnect the appliance from electricity supply.
Clean the inside and accossories with warm water and
bicarbonate of soda (5ml to 0,5 litre water).
Be careful when cleaning the inside of the fridge, due to
fragile edges.
Rinse and dry thoroughly.
Regularly check the door seals and wipe clean to ensure they
are clean and free from debris.
Wash the inside of the fridge using lukewarm water, a mild
washing-up detergent and a soft cloth.
Wash the outer fridge with warm soapy water. Remove the
ventilation grill (see above) and vacuum-clean under the
fridge. Once or twice a year dust the condenser (grill) and
the compressor at the back of the appliance, with a brush or
vacuum cleaner, as an accumulation of dust will affect the
performance of the appliance and cause excessive electricity
consumption.
Whenmovingthefridge,liftitbythefrontedge
to avoid scratching the floor.
Defrosting the fridge
The fridge is defrosted automatically every time the
compressor stops. Frost formation can be prevented by:
D not putting warm foodstuff inside the fridge.
D avoiding frequently opening the door or keeping it
open too long.
To change the light bulb
This fridge is fitted with a clear halogen light bulb. The light
is switched on automatically when the door is opened. If the
bulb fails and needs to be replaced; disconnect the power
from the fridge.
Cut the packaging containing the new bulb.
Keep the packaging on to hold the bulb when setting it into
the socket. Do not touch the bulb with your bare fingers.
Halogen light bulbs are sensitive to grease from the skin.
When the appliance is not in use
Disconnect the appliance from electricity supply.
Empty all foods and clean the appliance, leaving the doors
ajar to prevent unpleasant smells.
If the fridge will be kept on, ask somebody to check it once
in a while to prevent the food inside from spoiling in case of
a power failure.
You must disconnect the a ppliance f rom t he electr icity
supply, bef ore ca r r ying out a ny cleaning or ma intenance
wo r k .
The ventila tion g r ill ca n b e removed, e .g . t o wa sh t he
g r ill.
M a ke sure the door is open when removing the
ventilation gr ill. U nsnap the upper edg e of t he gr ill by
pulling outwa rd/ downwa rd. Then pull t he g r ill str a ig ht
out t o completely remove it.
Maintenance and Cleaning
UV-blocked
Low pressure20W/12V
G4
17
If your Refrigerator is not working correctly, before contacting the John Lewis extended warranty administrators, check the
following point.
IMPORTANT : If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a
charge will be made even if the appliance is under guarantee.
Sympton Solution
"" is displayed in the temperature display. D An error has occurred in measuring the temperature. (The cooling
system will continue to keep food products cold, but temperature
adjustment will not be possible.) Contact the John Lewis extended
warranty administrators, see service and spare parts page 18.
It is too warm inside the refrigerator. D Set a lower temperature.
D Put food products in the right place inside the refrigerator. See the
chapter "Temperature inside the refrigerator".
D Distribute the food products to allow cold air to circulate around
them.
D Make sure that the door is completely closed and that the insulating
strip is complete and clean.
It is too cold inside the refrigerator. D Set a warmer temperature.
Water comes out o n the floor. D Check that the drain hose at the back of the fridge above the drain
bowl is in position. See the chapter "Before using the fridge the first
time".
The compressor operates continuously. D Set a warmer temperature.
D Make sure that the door is completely closed and that the insulating
strip is complete and clean.
The fridge does not operate at all. Cooling
or interior light does not operate. No
indicator lamps light.
D Power does not reach the fridge. (Try connecting another electrical
device to the power outlet.)
D The fridge or power socket is not switched on.
D The fuse has blown.
D The power plug is not properly inserted into the socket.
Sound level in fridge is too high. D The refrigerating system will always produce some sounds.
A pulsing sound; A ticking sound and The sound level.
A pulsing sound is heard when coolant is pumped inside the cooling
pipes.
A ticking sound from the thermostat can be heard when the compressor
switches on and off.
The sound level varies depending on the operation of the fridge.
If you feel the sound level is incorrect:
D Makesurethepipesatthebackof thefridge nottoucheachother.
Carefully bend them if they do.
D If the cushion spacers (between the fridge wall and pipes) come
loose, put them back in place again.
D Carefully follow the instructions in the chapter "Installing the fridge".
I f af ter a bove ch ecksthere is still a f ault ccontact t he John L ewis extended wa r r a nty a dministr a t or s, see p a g e 18 f or deta ils.
In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is
not a mechanical or electrical breakdown.
Please note that proof of purchase is required for in-guarantee service calls.
Something Not Working
18
Repairs - After Sales Service
In the unlikely event of your appliance requiring service, or
if you wish to purchase spare parts, please contact our local
Service Force Centre by telephoning:
0870 010 7887
They will give you details for your local Service Force
Centre.
Before calling out an engineer, please ensure you have read
the details under the heading "Something Not Working".
When you contact your local Service Forse Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The purchase date and found on your receipt.
5. The model and serial number of the appliance (found on
the rating plate)
So that you always have these numbers at hand, we
recommend you to make a note of them here:
Mod:.................................................
PNC:................................................
S.N.:.................................................
Your fridge is covered by a 3 year parts and labour
guarantee (see separate details given at point of
sale). Please retain your purchase receipt safely for
the service engineer to verify the purchase details.
Spar e Parts
Always insist on genuine spare parts.
An authorised service engineer should service this
product, and only genuine spare parts should be used. Under
no circumstances should you attempt to repair the machine
yourself. Repairs carried out by inexperienced persons may
cause injury or serious malfunctioning. Contact your local
Service Force Centre. An authorised service engineer always
insist on genuine spare parts.
19
8183856--00/3
05/06
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
www.johnlewis.com
Loading...