JLDWW 1206
Dishwasher
Instruction manual
Important safety information
It is most important that this instruction book should be retained with
the appliance for future reference. Should the appliance be sold or
transferred to another owner, or should you move house and leave the
appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance
and the relevant warnings.
These warnings have been provided in the interest of safety. You MUST
read them carefully before installing or using the appliance. If you are
unsure of the meanings of these warnings contact the John Lewis branch
from which you purchased the appliance.
In the interest of your safety and to
ensure the correct use, before
installing and first using the appliance,
read this user manual carefully,
including its hints and warnings. To
avoid unnecessary mistakes and
accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation
and safety features. Save these
instructions and make sure that they
remain with the appliance if it is moved
or sold, so that everyone using it
through its life will be properly
informed on appliance use and safety.
If you are unsure of the meanings of
these warnings contact the John Lewis
branch from which you purchased the
appliance.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• Check your dishwasher for any transport
damage. Never connect a damaged
machine. If your dishwasher is damaged
contact your supplier.
• All packaging must be removed before use.
• Any electrical and plumbing work required
to install this appliance must be carried out
by a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supply cable and water hoses are damaged;
or if the control panel, work top or plinth
area are damaged such that the inside of the
appliance is freely accessible. Contact your
local repair agent, in order to avoid hazard.
• All sides of the dishwasher must never be
drilled to prevent damage to hydraulic and
electric components.
For electrical and water connection
carefully follow the instructions given
in the specific paragraphs.
Child safety
• This appliance is designed to be operated
by adults. Do not allow children to use the
dishwasher unsupervised.
• Keep all packaging well away from children.
There is a risk of suffocation.
2
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the
dishwasher when the door is open.
Correct use
• This dishwasher is only intended for
washing household utensils suitable for
machine washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Only use products (detergent, salt and
rinse aid) suitable for dishwashers.
• Avoid opening the door whilst the
appliance is in operation, hot steam may
escape.
• Do not take any dishes out of the
dishwasher before the end of the washing
cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorized service engineer, and only
genuine spare parts should be used.
• Under no circumstances should you
attempt to repair the machine yourself.
Repairs carried out by inexperienced
persons could cause injury or serious
malfunctioning. Contact your local repair
agent. Always insist on genuine spare parts.
General safety
• Dishwasher detergents can cause chemical
burns to eyes, mouth and throat. Could
endanger life! Comply with the safety
instructions of the dishwasher detergent
manufacturer.
• The water in your dishwasher is not for
drinking. Detergent residues may still be
present in your machine.
• Ensure that the door of the dishwasher is
always closed when it is not being loaded
or unloaded. In this way you will avoid
anybody tripping over the open door and
hurting themselves.
• Do not sit or stand on the open door.
Maintenance and cleaning
• For information on maintenance and
cleaning your dishwasher see the specific
chapter in this instruction manual.
Service
• This product should be serviced by an
authorized service engineer, and only
genuine spare parts should be used.
Ecological hints
To save water and energy and help protect
the environment, we recommend that you
follow these hints:
• Ensure that the water softener is correctly
adjusted.
• Do not prewash under running water.
• Select the wash programme to suit the
nature and degree of the soiling on the
dishes.
• Do not use more detergent, dishwasher
salt and rinse aid than is recommended in
these operating instructions and by the
manufacturer of the respective product.
•
Delay start: When possible programme
your dishwasher to run over night, to
enable, for example, the use of economical
overnight electricity tariffs.
3
•
45°-70° Auto Wash Programme: This
machine is fitted with a turbidity sensor
which intelligently adjusts the temperature
and rinsing cycles during the wash
programme, depending on the degree of
soiling on the dishes. This helps to reduce
energy and water consumption on lightly
soiled loads.
•
Half load: This option is useful and
economical when baskets are not fully
loaded.
Environmental
information
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate
container at the community waste disposal
facilities.
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and
dispose of them.
• Dispose of the door catch. This
prevents children from trapping
themselves inside and endangering
their lives.
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
4
Contents
For the user
Important safety information
Description of the appliance
Control panel
Menu options 8
Washing programmes
7
9
When the dishwasher is first
installed
The water softener 10
Filling with dishwasher salt 12
Filling with rinse aid 12
Adjusting the rinse aid dosage 13
Daily use
Loading cutlery and dishes 14
The lower basket 15
The cutlery basket 15
The upper basket 16
Adjusting the height of the upper basket 17
Use of detergent 17
Multi tab function
10
14
18
Select and start a washing
programme
19
Unloading the dishwasher
Maintenance and cleaning
Cleaning the filters 22
External cleaning 23
Internal cleaning 23
Something not working
24
2
6
22
22
For the installer
Technical data
Installation
Unpacking 27
Fitting under a counter 27
Levelling 28
Water connections
Water supply connections 28
Water inlet hose with safety valve 29
Water outlet hose connection 29
Electrical connection
Repairs - After sales service
27
27
28
31
31
Guide to use the
instruction manual
The following symbols will be found in the text
to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
5
Description of the appliance
1. Upper basket
2. Water hardness dial
3. Salt container
4. Detergent dispenser
5. Rinse aid dispenser
6. Rating plate
7. Filters
8. Lower spray arm
9. Upper spray arm
10. Worktop
This dishwasher has an internal light
that turns on when the door opens,
and off when it closes.
Internal light is equipped with led lamp
CLASS 1 in accordance with EN
60825-1: 1994 + A1: 2002 + A2: 2001.
In case this light has to be replaced,
please, contact your local repair agent.
6
Control panel
6
1. On/Off button
2. Programme scrolling buttons
3. Multi tab button
4. Half load button
5. Delay start button
6. Display
A sequence of displayed messages and
audible signals will guide you in the
setting up of the appliance and the
selection of washing programme and
options.
Half load button
This option is useful and economical when
baskets are not fully loaded. It reduces the
consumption of water and energy.
Remember to load both baskets.
When using this option we recommend that
you reduce the dose of detergent that is
normally used for a complete load.
Press the half load button to activate the
option:
•
the half load option is NOT available with
''45°-70° Auto'' programme; the half load
indicator light will not illuminate when the
half load button is pressed and the message
NOT SELECTABLE will appear on the
display.
• the half load option is available with all the
other programmes; the half load indicator
light illuminates when the half load button
is pressed and the message HALF
LOAD appears on the display. This option
has no impact on some washing
programmes. Refer to ''Washing
programmes'' section.
7
Menu options
Setting an option is possible ONLY with the
appliance in setting mode.
The message CHOOSE PROGRAMME
on the display indicates that the appliance is in
setting mode.
It will NOT be possible to enter the menu
options when:
• A washing programme and a delay start
have already been set or are in progress.
Cancel the programme and delay start to
return to setting mode.
• The washing programme has just ended.
Switch off the appliance and then switch it
on again; the appliance is in setting mode.
Menu options Submenu
Language
Sound volume 5 levels available
Brightness 10 levels available
Contrast
Water hardness
Rinse aid
Allows you to select the language for the display
of the messages
level 0 = volume deactivated (ALL audible signals
are deactivated)
10 levels available
Allows you to set the water softener according to
the hardness of the water in your area.
10 levels available
Allows you to reactivate the rinse aid dispenser.
0 = rinse aid dispenser deactivated
1 = rinse aid dispenser activated.
Available only with the Multi tab function active.
The appliance will return to the
programme menu if an option is not
selected within a few seconds.
To enter the menu options:
• Simultaneously press and hold the
programme scrolling buttons until option
language appears flashing in the display.
• With the button on your left you can skip
to another option;
• with the button on your right you enter the
sub menu.
• To confirm the selection made wait a few
seconds and the appliance will return to
programme setting.
8
Washing programmes
Programme Degree of soil Type of load Programme description
Prewash
Crockery,
70° Intensive
45°-70° Auto
50° Bio
60° Quick
Glass
Prewash
1) During the Auto washing programme the level of soiling on the dishes is determined by how cloudy the water is.
The programme duration, water and energy consumption levels can vary; this depends upon whether the appliance
is fully or partially loaded and if the dishes are lightly or heavily soiled. The temperature of the water is automatically
adjusted between 45°C and 70°C.
2) Test programme for test institutes.
3) Ideal for washing a partially loaded dishwasher. This is the perfect daily programme, made to meet the needs of a
family of 4 persons who only wish to load breakfast and dinner crockery and cutlery.
1)
2)
3)
Heavy soil
Any
Normal soil
Normal or light soil
Normal soil
Any.
cutlery, pots and
pans
Crockery,
cutlery, pots and
pans
Crockery and
cutlery
Crockery and
cutlery
Delicate crockery
and glassware
Partial load (to be
completed later
in the day).
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
Prewash
Main wash up to 45°C or 70°C
1 or 2 intermediate rinses
Final rinse
Drying
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
Main wash up to 60°C
Final rinse
Main wash up to 45°C
1 intermediate rinse
Final rinse
Drying
1 cold rinse (to avoid food scraps from
sticking).
This programme does not require the
use of detergent.
Half load option available with programme:
70° Intensive
45°-70° Auto NO (not selectable)
50° Bio
60° Quick
Glass
YES (impact on washing programme)
YES (impact on washing programme)
YES (no impact on washing programme)
YES (no impact on washing programme)
9
Prewash
Half load option available with programme:
YES (no impact on washing programme)
Consumption values
Programme Programme
duration
(in minutes)
70° Intensive
45°-70° Auto
50° Bio
60° Quick
Glass
Prewash 12 0,1 4
1) The consumption values are intended as a guide and depends on the pressure and the temperature of the water
2) Test programme for test institutes.
2)
and also by the variations of the power supply and the amount of dishes.
110 - 120 1,8 - 2,0 23 - 25
90 - 115 1,1 - 1,5 12 - 23
150 - 160 1,0 - 1,2 12 - 14
30 0,9 9
60 - 70 0,8 - 0,9 14 - 15
1)
Energy
consumption
(in kWh)
Water consumption
(in litres)
When the dishwasher is first
installed
Before using your dishwasher for the first
time:
• Ensure that the electrical and water
connections comply with the installation
instructions
• Remove all packaging from inside the
appliance
• Set the water softener level
• Pour 1 litre of water into the salt container
and then fill with dishwasher salt
• Fill the rinse aid dispenser
If you want to use combi detergent
tablets such as "3 in 1", "4 in 1", "5 in 1"
etc... set the Multi tab function (see
"Multi tab function").
The water softener
The dishwasher is equipped with a water
softener designed to remove minerals and
salts from the water supply, which would have
a detrimental or adverse effect on the
operation of the appliance.
The higher the content of these minerals and
salts, the harder your water is. Water
hardness is measured in equivalent scales,
Clarke degrees, French degrees (°TH) and
mmol/l (millimol per litre - international unit
for the hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
10
Water hardness
Clarke °TH mmol/l manually electronically
64 - 88 91 - 125 9,1 - 12,5 2 level 10 yes
53 - 63 76 - 90 7,6 - 8,9 2 level 9 yes
46 - 52 65 - 75 6,5 - 7,5 2 level 8 yes
36 - 45 51 - 64 5,1 - 6,4 2 level 7 yes
28 - 35 40 - 50 4,0 - 5,0 2 level 6 yes
23 - 27 33 - 39 3,3 - 3,9 2 level 5 yes
18 - 22 26 - 32 2,6 - 3,2 1 level 4 yes
13 - 17 19 - 25 1,9 - 2,5 1 level 3 yes
5 - 12 7 - 18 0,7 - 1,8 1 level 2 yes
< 5 < 7 < 0,7 1 level 1 no
Adjusting the water hardness
setting
Setting the water
softener
The water softener must be set in two ways:
manually, using the water hardness dial and
electronically in menu options.
Use of salt
Setting manually
The dishwasher is factory set at
position 2.
1. Open the dishwasher door.
2. Remove the lower basket from the
dishwasher.
3. Turn the water hardness dial to position 1
or 2 (see table above).
4. Replace the lower basket.
Setting electronically
The dishwasher is factory set at level 5.
Menu options: Water hardness
With the help of the chart, set the level of the
water softener according to the hardness of
the water in your area.
11
Filling with dishwasher
salt
Warning! Only use salt specifically
designed for use in dishwashers. All
other types of salt not specifically
designed for use in a dishwasher,
especially table salt, will damage the
water softener. Only fill with salt just
before starting one of the complete
washing programmes. This will
prevent any grains of salt or salty
water, which may have been spilt,
remaining on the bottom of the
machine for any period of time, which
may cause corrosion.
To fill:
1. Open the door, remove the lower basket
and unscrew the cap of the salt container
by turning it anticlockwise.
2. Pour 1 litre of water into the container
(this is necessary only before filling
with salt for the first time).
3. Using the funnel provided, pour in the salt
until the container is full.
5. Replace the cap tightly turning it clockwise
until it stops with a click.
Do not worry if water overflows from
the unit when filling with salt, this is
quite normal.
The salt container will require topping up
periodically. You are reminded of this by a
displayed message.
This occurs only at the start and at the end of
the washing programme; during the running of
the programme the indication for salt refilling
is not active.
The refilling salt message can remain
visible for 2-6 hours after the salt has
been replenished, assuming the
dishwasher remains switched on. If
you are using salt that takes longer to
dissolve then this can take longer. The
operation of the machine is not
affected.
Filling with rinse aid
Warning! Only use branded rinse aid
for dishwashers.
Never fill the rinse aid dispenser with
any other substances (e.g. dishwasher
cleaning agent, liquid detergent). This
would damage the appliance.
4. Replace the cap making sure that there is
no trace of salt on the screw thread or on
the gasket.
Rinse aid ensures thorough rinsing, and
spot and streak free drying.
Rinse aid is automatically added during
the last rinse.
1. Open the container by pressing the
release button (A).
12
2. Add the rinse aid in the container. The
maximum level for filling is indicated by
"max".
Adjusting the rinse aid
dosage
According to the finish and drying results
obtained, adjust the dose of rinse aid by means
of the 6 position selector (position 1=
minimum dosage, position 6= maximum
dosage).
The dose is factory set in position 4.
Increase the dose if there are drops of water
or lime spots on the dishes after washing.
Reduce it if there are sticky whitish streaks on
the dishes or a bluish film on glassware or knife
blades.
The dispenser holds about 110 ml of rinse
aid, which is sufficient for between 16 and
40 dishwashing cycles, depending upon
the dosage setting.
3. Ensure that the lid is closed after every
refill.
Clean up any rinse aid spilt during filling
with an absorbent cloth to avoid
excess foaming during the next wash.
The rinse aid container will require
topping up periodically. You are
reminded of this by a displayed
message. This occurs only at the start
and at the end of the washing
programme; during the running of the
programme the indication for rinse aid
refilling is not active.
13
Daily use
• Check if it's necessary to refill with
dishwasher salt or rinse aid.
• Open the door and slide out the baskets to
load the dishes.
• Load cutlery and dishes into the
dishwasher.
• Fill with dishwasher detergent.
• Select a wash programme suitable for the
cutlery and dishes.
• Start the wash programme.
Loading cutlery and
dishes
Sponges, household cloths and any object that
can absorb water may not be washed in the
dishwasher.
• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
For washing in the dishwasher the following cutlery and dishes
are not suitable: are of limited suitability:
• Cutlery with wooden, horn, china or motherof-pearls handles.
• Plastic items that are not heat resistant.
• Older cutlery with glued parts that are not
temperature resistant.
• Bonded cutlery items or dishes.
• Pewter or copper items.
• Lead crystal glass.
• Steel items prone to rusting.
• Wooden platters.
• Items made from synthetics fibres.
• When loading the dishes and cutlery, please
note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Load hollow items such as cups, glasses,
pans, etc. with the opening downwards
so that water cannot collect in the
container or a deep base.
– Dishes and items of cutlery must not lie
inside one another or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick
coatings have a tendency to retain water
drops; these items will not dry as well as
porcelain and steel items.
• Light items (plastic bowls etc.) must be
loaded in the upper basket and arranged so
they do not move.
• Only wash stoneware in the dishwasher if it is
specially marked as being dishwasher-safe by
the manufacturer.
• Glazed patterns may fade if machine washed
frequently.
• Silver and aluminium parts have a tendency to
discolour during washing: Residues, e.g. egg
white, egg yolk and mustard often cause
discolouring and staining on silver. Therefore
always clean left-overs from silver immediately,
if it is not to be washed straight after use.
14
The lower basket
The lower basket is designed to take
saucepans, lids, plates, salad bowls, cutlery,
etc.
Serving dishes and large lids should be
arranged around the edge of the basket,
ensuring that the spray arms can turn freely.
The cutlery basket
Warning! Long bladed knives stored
in an upright position are a potential
hazard. Long and/or sharp items of
cutlery such as carving knives must be
positioned horizontally in the upper
basket. Take care when loading or
unloading sharp items such as knives.
Forks and spoons should be placed in
the removable cutlery basket with the
handles facing downwards and the
knives with their handles facing
upwards
The rows of prongs in the lower basket can
lie flat to allow you to load pots, pans and
bowls.
15
If the handles protrude from the bottom of
the basket, obstructing the lower spray arm,
load the cutlery with the handles facing
upwards. Mix spoons with other cutlery to
prevent them from sticking together.
For best results we recommend you use the
cutlery grids. If the size and dimensions of the
cutlery do not allow the use of the grids, they
can be easily hidden or removed.
Glasses with long stems can be placed upside
down in the cup racks.
For taller items, the cup racks can be folded
upwards.
The upper basket
The upper basket is designed for saucers,
salad bowls, cups, glasses, pots and lids.
Arrange items on and underneath the cup
racks so that water can reach all surfaces.
For glasses with long stems (according to the
size and dimensions), set the glass holder to
the left or right position.
16
Before closing the door, ensure that
the spray arms can rotate freely.
Adjusting the height of
the upper basket
If washing very large plates you can load them
in the lower basket after moving the upper
basket to the higher position.
Maximum height of the dishes in the
lower basket
With upper basket
raised
With upper basket
lowered
31 cm
27 cm
To lower the basket to the original
position proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards and then
allow the mechanism to drop back down
slowly, keeping hold of it.
Never lift or lower the basket on
one side only.
When the upper basket is raised
you will not be able to use the
cup racks.
Warning! After loading your
machine always close the door, as an
open door can be a hazard.
To move to the higher position
proceed as follows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the
mechanism is engaged and the basket is
stable.
Use of detergent
Only use detergents specifically
designed for use in dishwashers.
Please observe the manufacturer’s
dosing and storage recommendations
as stated on the detergent packaging.
Fill with detergent
1. Open the lid.
17
2. Fill the detergent dispenser (1) with
detergent. The marking indicates the
dosing levels:
20 = approximately 20 g of detergent
30 = approximately 30 g of detergent
3. All programmes with prewash need an
additional detergent dose (5/10 g) that
must be placed in the prewash detergent
chamber (2). This detergent will be used
during the prewash phase.
When using detergent tablets; place the
tablet in compartment (1).
Detergent tablets
Detergent tablets from different
manufacturers dissolve at different
rates. For this reason, some detergent
tablets do not attain their full cleaning
power during short washing
programmes. Therefore, please use
long washing programmes when using
detergent tablets, to ensure the
complete removal of detergent
residuals.
Multi tab function
This appliance is equipped with the Multi tab
function, that allows the use of combi
detergent tablets.
These products are detergents with a
combined cleaning, rinsing and salt functions.
They can also contain other different agents
depending on which kind of tablets you
choose ("3 in 1", "4 in 1", "5 in 1" etc...).
Check whether these detergents are suitable
for your water hardness. See the
manufacturers instructions.
18
Once this function is selected it will remain
active for all following wash programmes.
With the selection of this function the inflow
of rinse aid and salt from each respective
supply container is automatically deactivated
and also the indicator lights for salt and rinse
aid are deactivated.
When using the Multi tab function, the cycle
durations may change. If this is the case, the
running time for the programme is
automatically updated on the digital display.
Activate/deactivate the Multi tab
function before the start of a washing
programme.
Once the programme is running, the
Multi tab function can NO longer be
changed. If you want to cancel the
Multi tab function you have to cancel
the programme setting and then
deactivate the Multi tab function.
In this case you have to set a washing
programme (and desired options)
again.
Activation/deactivation
of the Multi tab function
Press the Multi tab button, the corresponding
indicator light illuminates. This means that the
function is active.
To deactivate the function press the Multi-tab
button again until the Multi tab indicator light
turns off.
If the drying results are not
satisfactory we suggest that you:
1. Fill up the rinse aid dispenser with
rinse aid.
2. Activate the rinse aid dispenser.
3. Set the rinse aid dosage to position
2.
• The activation/deactivation of the
rinse aid dispenser is only possible
with the Multi tab function active.
If you decide to revert back to the use
of individual detergents we advise that
you:
1. Deactivate the Multi tab function.
2. Fill up the dispensers for salt and
rinse aid again.
3. Adjust the water hardness setting
to the highest setting and perform
1 normal washing programme
without loading any dishes.
4. Adjust the water hardness setting
according to the hardness of the
water in your area.
5. Adjust the rinse aid dosage.
Select and start a washing
programme
1. Check that the baskets have been loaded
correctly and that the spray arms are free
to rotate.
2. Check that the water tap is opened.
19
Set the washing programme, delay
start and half load with the dishwasher
door slightly open.
The selection can also occur with the
door closed. Keep in mind that this
way you have ONLY 3 seconds
between one selection and another,
after which the washing programme
will start automatically.
3. Switch on the dishwasher. The appliance
must be in setting mode: message
CHOOSE PROGRAMME displayed.
4. Select the washing programme by
pressing one of the programme scrolling
buttons.
If a button is pressed only once, the last
performed washing programme will be
proposed.
5. If required, postpone the start time of the
washing programme by using the delay
start option. The start of the washing
programme can be delayed for between 1
and 19 hours.
6. Close the dishwasher door, the
programme starts automatically. Once
the programme is running the display
shows:
– the phases of the progress of the
programme,
– updates the running time of the
programme.
7. If the start of the programme has been
postponed, the countdown will start
automatically once the dishwasher door is
closed.
The countdown will decrease in steps of
1 hour.
Opening the door will interrupt the
countdown. Close the door; the
countdown will continue from the point at
which it was interrupted.
Once the delay start has elapsed the
programme will start automatically.
If during the progress of the delay start
or the running of the washing
programme you wish to see which
programme has been set or is
performing; press one of the
programme scrolling buttons. The
name of the programme will appear
for a few seconds in the display.
Warning! Interrupt or cancel a
washing programme in progress
ONLY if it’s absolutely
necessary. Attention! Hot steam
may escape when the door is
opened. Open the door carefully.
Cancelling a delay start or
a washing programme in
progress
• To cancel a washing programme or a delay
start in progress you have to reset the
appliance.
Cancelling a delay start will also cancel
a washing programme. You have to set
the washing programme again.
• Simultaneously press and hold the two
buttons positioned over the word Cancel
until the message CHOOSE
PROGRAMME appears on the display.
The washing programme or the delay start
has been cancelled.
• If a new washing programme is to be
selected, check that there is detergent in
the detergent dispenser.
20
Interrupt a washing
programme in progress
• Open the dishwasher door; the
programme will stop. Close the door; the
programme will start from the point at
which it was interrupted.
• Press the On/Off button; all lights will turn
off. Press the On/Off button again; the
programme will start from the point at
which it was interrupted
End of the washing
programme
• The dishwasher will automatically stop and
an audible signal informs you of the end of
the washing programme. (No audible signal
if the sound volume option has been
deactivated).
•
The message PROGRAMME END
appears on the display.
The dishwasher’s drying system is
provided with a device that allows air
to circulate inside the dishwasher to
prevent residual steam recondensing
on the dishes as water droplets.
Once the washing programme has
ended this device operates
intermittently for another 20
minutes, as long as the
dishwasher is switched on.
If the On/Off button is pressed or the
door is opened during these 20
minutes, the device will be
automatically cancelled.
1. Switch off the dishwasher.
2. Open the dishwasher door and leave it
ajar. Wait a few minutes before removing
the dishes; this way they will be cooler and
the drying will be improved.
When the washing programme
has finished, it is recommended
that the dishwasher is unplugged
and the water tap turned off.
21
Unloading the dishwasher
• Hot dishes are sensitive to knocks. The
dishes should therefore be allowed to cool
down before removing from the appliance.
• Empty the lower basket first and then the
upper one; this will avoid water dripping
from the upper basket onto the dishes in
the lower one.
• Water may appear on the sides and the
door of the dishwasher as the stainless steel
will eventually become cooler than the
dishes.
Maintenance and cleaning
Cleaning the filters
The filters must be checked and cleaned from
time to time. Dirty filters will degrade the
washing result.
A displayed message will periodically
appear to remind you to clean the
filters.
Warning! Before cleaning the
filters ensure that the machine is
switched off.
1. Open the door, remove the lower basket.
2. The dishwasher filter system comprises a
coarse filter (A), a microfilter (B) and a
flat filter. Unlock the filter system using the
handle on the microfilter.
3. Turn the handle about 1/4 a turn
anticlockwise and remove the filter
system.
22
4.
Take hold of the coarse filter (A) by the
handle with the hole and remove from the
microfilter (B).
5. Clean all filters thoroughly under running
water.
6. Remove the flat filter from the base of the
washing compartment and clean both
faces thoroughly.
flat filter does not protrude above the
base of the washing compartment.
NEVER use the dishwasher
without filters.
Incorrect repositioning and fitting of
the filters will produce poor washing
results and will result in damage to the
appliance.
NEVER try to remove the spray
arms.
If residues of soil have clogged the
holes in the spray arms, remove the
debris with a cocktail stick.
External cleaning
Clean the external surfaces of the machine
and control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or
solvent (acetone, trichloroethylene etc...).
Internal cleaning
Ensure that the seals around the door, the
detergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
We recommend every 3 months you run the
wash programme for heavy soiled dishes using
detergent but without dishes.
7. Put the flat filter back in the base of the
washing compartment and ensure that it
fits perfectly.
8.
Place the coarse filter (A) in the
microfilter (B) and press together.
9. Put the filter combination in place and lock
by turning the handle clockwise to the
stop. During this process ensure that the
Prolonged periods of nonoperation
If you are not using the machine for a
prolonged period of time you are advised to:
1. Unplug the appliance and then turn off the
water.
2. Leave the door ajar to prevent the
formation of any unpleasant smells.
3. Leave the inside of the machine clean.
23
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable, empty the machine, close the
appliance door, disconnect the water inlet
pipe and empty it.
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge
hoses.
4. Pull the machine out together with the
hoses.
Avoid over tilting the machine during
Moving the machine
transportation.
If you have to move the machine (moving
house, etc...):
Something not working
The dishwasher will not start or stops during
operation.
Certain problems are due to the lack of simple
maintenance or oversights, which can be
solved with the help of the indications
Important! If you call out an engineer to a
fault listed below, or to repair a fault caused
by incorrect use or installation, a charge will
be made even if the appliance is under
guarantee.
described in the chart, without calling out an
engineer.
Switch off the appliance and carry out the
following suggested corrective actions.
Fault code and malfunction Possible cause and solution
•
intermittent audible signal is active
•
appears in the digital display
•
message OPEN THE TAP
displayed
The dishwasher does not fill with
water
•
intermittent audible signal is active
•
appears in the digital display
•
message DRAIN BLOCKED
displayed
The dishwasher will not drain
1)
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off.
Turn the water tap on.
• The filter (where present) in the threaded hose fitting at
the water inlet valve is blocked.
Clean the filter in the threaded hose.
• The water inlet hose has not been correctly laid or it is
bent or squashed.
Check the water inlet hose connection.
1)
• The sink spigot is blocked.
Clean out the sink spigot.
• The water drain hose has not been correctly laid or it is
bent or squashed.
Check the water drain hose connection.
24
Fault code and malfunction Possible cause and solution
•
intermittent audible signal is active
•
appears in the digital display
•
message SERVICE NUMBER
displayed
Anti-flood device is activated
1) Audible signals not active if option sound volume has been deactivated.
Malfunction Possible cause and solution
The programme does not start • The dishwasher door has not been properly closed.
1)
• Close the water tap and contact our extended warranty
administrators, refer to Repairs-After Sales Service on the
following pages.
(Message CLOSE THE DOOR displayed).
Close the door.
• The main plug is not plugged in.
Insert the main plug.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start has been set.
If dishes are to be washed immediately, cancel the delay
start.
Once these checks have been carried out
switch on the appliance.
warranty administrators, refer to section
''Repairs - After Sales Service''.
The programme will continue from the point
at which it was interrupted.
If the malfunction/fault code reappears or if
other fault codes not described in the charts
appear, please contact our extended
The wash results are not satisfactory
The dishes are not clean • The wrong programme has been selected.
• The dishes are arranged in such a way as to stop water
reaching all parts of the surface. The baskets must not
be overloaded.
• The spray arms do not rotate freely due to incorrect
arrangement of the load.
• The filters in the base of the washing compartment are
dirty or incorrectly positioned.
• Too little or no detergent has been used.
• Where there are limescales deposits on the dishes; the
salt container is empty or the incorrect level of the water
softener has been set.
• The drain hose connection is not correct.
• The salt container cap is not properly closed.
25
The wash results are not satisfactory
The dishes are wet and dull
There are streaks, milky spots or a
bluish coating on glasses and dishes
Water drops have dried onto
glasses and dishes
• Rinse aid was not used.
• The rinse aid dispenser is empty.
• Decrease rinse aid dosage.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent
manufacturer’s consumer care line.
26
Technical data
Dimensions Width
Height
Depth
Electrical connection - Voltage - Overall
power - Fuse
Water supply pressure Minimum
Capacity 12 place settings
Weight 47,8 kg
Information on the electrical connection is given on the
rating plate on the inner edge of the dishwasher door.
0,5 bar (0,05 MPa)
Maximum
8 bar (0,8 MPa)
60 cm
85 cm
61 cm
Installation
Warning! It is dangerous to alter the
specifications or attempt to modify this
product in any way.
This appliance is heavy. Care should be
taken when moving it.
Care must be taken to ensure that the
appliance does not stand on the
electrical supply cable.
Any electrical work required to install
this appliance must be carried out by a
qualified electrician or competent
person.
Any plumbing work required to install
this appliance must be carried out by a
qualified plumber or competent
person.
Fitting under a counter
(Kitchen worktop or sink)
By removing the machine’s worktop, you can
install it under a close fitting sink unit or a preexisting top, providing the dimensions of the
recess correspond to those shown in the
picture.
Unpacking
• Remove all packaging before positioning
the machine.
• If possible, position the machine next to a
water tap and a drain.
27
Proceed as follows:
Remove the machine’s worktop by
unscrewing the two rear retaining screws (1),
pull the worktop from the back of the machine
(2) and slide out the front slots, lifting the
worktop (3).
Insert the machine after adjusting the levelling
with the adjustable feet. When inserting the
machine, ensure that the water inlet and drain
hoses are not kinked or squashed.
During all operations that involve accessibility
to internal components the dishwasher has to
be unplugged.
Be sure that once the appliance has been
installed, it is easily accessible for the service
engineer in the event that a repair is required.
If the dishwasher is later used as a freestanding appliance, the original worktop must
be re-mounted.
The plinth on free-standing appliances is not
adjustable.
Levelling
Good levelling is essential for correct closure
and sealing of the door. When the appliance
is correctly levelled, the door will not catch on
either side of the cabinet. If the door does not
close correctly, loosen or tighten the
adjustable feet until the machine is perfectly
level.
Water connections
Water supply
connections
This dishwasher may be fed with either hot
(max. 60°) or cold water. Nevertheless we
advise you use a cold water supply.
A hot water supply is not always efficient with
heavily soiled crockery as it shortens the
washing programmes a lot.
For making the connection itself, the coupling
nut fitted to the machine’s supply hose is
designed to screw onto a 3/4" gas thread
28
spout or to a purpose made quick-coupling
tap such as the Press-block.
The water pressure must be within the limits
given in the "Technical data". Your local
Water Authority will advise you on the
average mains pressure in your area.
The water inlet hose must not be kinked,
crushed, or entangled when it is being
connected.
The dishwasher features fill and drain hoses
which can be turned either to the left or the
right to suit the installation by means of the
locknut. The locknut must be correctly
fitted to avoid water leaks. (Attention!
NOT all models of dishwashers have fill and
drain hoses provided with a locknut.)
If the machine is connected to new pipes or
pipes which have not been used for a long
time, you should run the water for a few
minutes before connecting the inlet hose.
DO NOT use connection hoses which
have previously been used on an old
appliance.
This appliance has been fitted with
safety features which will prevent the
water used in the appliance from
returning back into the drinking water
system. This appliance complies with
the applicable plumbing regulations.
Water inlet hose with
safety valve
After connecting the double-walled water
inlet hose, the safety valve is next to the tap.
Therefore the water inlet hose is only under
pressure while the water is running. If the
water inlet hose starts to leak during this
operation, the safety valve cuts off the running
water.
Please take care when installing the water inlet
hose:
• The electrical cable for the safety valve is in
the double-walled water inlet hose. Do not
immerse the water inlet hose or the safety
valve in water.
• If water inlet hose or the safety valve is
damaged, remove the mains plug
immediately.
• A water inlet hose with safety valve must
only be replaced by a local repair agent.
Warning! Dangerous voltage
Water outlet hose
connection
The end of the drain hose can be connected
in the following ways:
1. To the sink outlet spigot, securing it to the
underside of the work surface. This will
prevent waste water from the sink running
into the machine.
2. To a stand pipe provided with venthole,
minimum internal diameter 4 cm.
The waste connection must be at a height of
between 30 cm (minimum) and 100 cm
(maximum) from the bottom of the
dishwasher.
29
The drain hose can face either to the right or
left of the dishwasher.
Ensure the hose is not bent or squashed as this
could prevent or slow down the discharge of
water.
The sink plug must not be in place when the
machine is draining as this could cause the
water to syphon back into the machine.
If you use a drain hose extension it must be
no longer than 2 metres and its internal
diameter must be no smaller than the
diameter of the hose provided.
Likewise the internal diameter of the
couplings used for connections to the waste
outlet must be no smaller than the diameter
of the hose provided.
When connecting the drain hose to an
under sink trap spigot, the entire
plastic membrane (A) must be
removed. Failure to remove all the
membrane will result in food particles
building up over time eventually
blocking the dishwasher drain hose
spigot.
Our appliances are supplied with a
security device to protect against the
return of dirty water back into the
machine. If the spigot of your sink has
a "no return valve" incorporated this
can prevent the correct draining of
your dishwasher. We therefore advise
you to remove it. When connecting
the drain hose to an under sink trap
spigot, the entire plastic membrane
(A) must be removed. Failure to
remove all the membrane will result in
food particles building up over time
eventually blocking the dishwasher
drain hose spigot
30
Electrical connection
Warning! Safety standards require
the appliance to be earthed.
Prior to using the appliance for the first
time, ensure that the rated voltage and
type of supply on the rating plate
match that of the supply where the
appliance is to be installed. The fuse
rating is also to be found on the rating
plate.
Always plug the mains plug into a
correctly installed shockproof socket.
Multi-way plugs, connectors and
extension cables must not be used.
This could constitute a fire hazard
through overheating.
If necessary, have the domestic wiring
system socket replaced. In case that
the electrical cable has to be replaced,
contact your local repair agent.
The plug must be accessible after the
appliance has been installed.
Never unplug the appliance by pulling
on the cable. Always pull the plug.
The manufacturer accepts no liability
for failure to observe the above safety
precautions.
Repairs - After sales service
If the unlikely event of your appliance requiring
service, or if you wish to purchase spare parts,
please contact our extended warranty
administrators by telephoning:
0870 010 7887
They will give you details of your local Service
Force Centre.
Before calling out an engineer, please ensure
you have read the details under the heading
''Something Not Working''.
When you contact your local repair agent you
will need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of fault.
31
4. The purchase date (found on your
receipt).
5. The model and serial number of the
appliance (found on the rating plate).
So that you always have these numbers at
hand, we recommend that you make a note
of them here:
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.No. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Your dishwasher is covered by a 3 year parts
and labour guarantee (see separate details
given at point of sale). Please retain your
purchase receipt safely for the service
engineer to verify the purchase details.
Spare parts
Always insist on genuine spare parts.
An authorised service engineer should service
this product and only genuine spare parts
should be used.
Under no circumstances should you attempt
to repair the machine yourself. Repairs carried
out by inexperienced persons may cause
injury or serious malfunctioning. Contact your
local repair agent by telephoning:
0870 010 7887
32
333435
John Lewis Partnership
171 Victoria Street
London SW1E 5NN
www. johnlewis.com
117986660 - 01 - 062007 - Subject to change without notice
Loading...