Page 1
JLBIGGH605
Gas hob
Instruction manual
GB
Page 2
ImporImpor
Impor
ImporImpor
It is most important that this instruction manual should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings. These warnings have been provided in the interest of safety. You MUST read them
carefully before use or installation by a qualified person. If you are unsure of the meanings of
these warnings contact the John Lewis branch from which you purchased the appliance.
tant Saftant Saf
tant Saf
tant Saftant Saf
ety Infety Inf
ety Inf
ety Infety Inf
ormationormation
ormation
ormationormation
InstallationInstallation
Installation
InstallationInstallation
z This hob must be installed by qualified
and competent personnel to the
relevant National Standards.
z Refer to Installation information from page
6 to page 17.
z Remove all packaging before using the
hob.
z Ensure that the gas and electrical supply
complies with the type stated on the
rating plate, located near the gas supply
pipe.
z Do not attempt to modify the hob in any
way.
Personal SafetyPersonal Safety
Personal Safety
Personal SafetyPersonal Safety
z This hob is designed to be operated by
adults. Do not allow children to play near
or with the hob.
z This appliance is not intended for use by
children or other persons whose physical,
sensory or mental capabilities or lack of
experience and knowledge prevents them
from using the appliance safely without
supervision or instruction by a responsible
person to ensure that they can use the
appliance safely.
z The hob gets hot when it is in use.
Children should be kept away until it has
cooled.
z Children can also injure themselves by
pulling pans or pots off the hob.
During UseDuring Use
During Use
During UseDuring Use
z This hob is intended for domestic cooking
only. It is not designed for commercial or
industrial purposes.
• Appliances become very hot with use,
and retain their heat for long periods after
use. Care should be taken to avoid
touching heating elements inside the hob.
• Always stand back from the hob when
opening the hob door during cooking
or at the end of it to allow any build up
of steam or heat to release.
z When in use a gas cooking hob will pro-
duce heat and moisture in the room in
which it has been installed. Ensure there
is a continuous air supply, keeping air
vents in good condition or installing a
cooker hood with a venting hose.
z When using the hob for a long period
time, the ventilation should be improved,
by opening a window or increasing the
extractor speed.
z Do not use this hob if it is in contact with
water. Do not operate the hob with wet
hands.
z Ensure the control knobs are in the ‘OFF’
position when not in use.
z When using other electrical appliances,
ensure the cable does not come into
contact with the hot surfaces of the
cooking appliance.
2
Page 3
z Unstable or misshapen pans should not
be used on the hob as unstable pans can
cause an accident by tipping or spillage.
z Never leave the hob unattended when
cooking with oil and fats.
z Never use plastic or aluminium foil dishes
on the hob.
z Perishable food, plastic items and aerosols
may be affected by heat and should not
be stored above or below the hob unit.
z This appliance is not connected to a
combustion products evacuation device.
It must be installed and connected in
accordance with current installation
regulations. Particular attention shall be
given to the relevant requirements
regarding ventilation.
z Ensure a good ventilation around the
appliance. A poor air supply could cause
lack of oxygen.
Maintenance andMaintenance and
Maintenance and
Maintenance andMaintenance and
CleaningCleaning
Cleaning
CleaningCleaning
z For cleaning, the appliance must be
switched off and cooled down.
z For safety reasons, the cleaning of the
appliance with steam jet or high pressure
cleaning equipment is not permitted.
EnvironmentalEnvironmental
Environmental
EnvironmentalEnvironmental
InformationInformation
Information
InformationInformation
z After installation, please dispose of the
packaging with due regard to safety and
the environment.
z When disposing of an old appliance, make
it unusable, by cutting off the cable.
z The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment. By
ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the
environment and human health, which
could otherwise be caused by
inappropriate waste handling of this
product. For more detailed information
about recycling of this product, please
contact your local city office, your
household waste disposal service or the
shop where you purchased the product.
SerSer
vicevice
Ser
vice
SerSer
vicevice
z This hob should only be repaired or
serviced by an authorised Service Engineer
and only genuine approved spare parts
should be used.
These instructions are only valid for countries whose identification symbols are shown in the
cover of this instruction booklet and on the appliance itself.
KK
eep this instruction book feep this instruction book f
K
eep this instruction book f
KK
eep this instruction book feep this instruction book f
anan
y ney ne
w ow o
wnerwner
an
anan
y ne
y ney ne
w o
w ow o
wner
wnerwner
..
.
..
or futuror futur
or futur
or futuror futur
e re r
e r
e re r
efef
erer
ence and ensurence and ensur
ef
er
ence and ensur
efef
erer
ence and ensurence and ensur
3
e it is passed on toe it is passed on to
e it is passed on to
e it is passed on toe it is passed on to
Page 4
ContentsContents
Contents
ContentsContents
Important Safety InformationImportant Safety Information
Important Safety Information
Important Safety InformationImportant Safety Information
Description of the Hob ................................ 5
Instructions for the InstallerInstructions for the Installer
Instructions for the Installer
Instructions for the InstallerInstructions for the Installer
Installation ....................................................... 6
Gas Connection ............................................. 6
Engineer technical data ................................ 7
Electrical Connections .................................. 8
Wiring diagram .............................................. 9
Fault Finding.................................................. 10
Commissioning ............................................. 12
Conversion from Natural Gas to LPG .... 13
Building In...................................................... 14
Fitting the Hob into the Worktop ............ 15
Important safety requirements .................. 16
Instructions for the UserInstructions for the User
Instructions for the User
Instructions for the UserInstructions for the User
Operation ...................................................... 18
Cleaning the hob ......................................... 20
Something Not Working? ........................... 22
Repairs - After Sales Service ...................... 23
Guide to Use theGuide to Use the
Guide to Use the
Guide to Use theGuide to Use the
instructionsinstructions
instructions
instructionsinstructions
........................
............
........................
..........................
.............
..........................
......................................
...................
......................................
1818
18
1818
22
2
22
66
6
66
The following symbols will be found in the text
to guide you throughout the Instructions:
Safety Instructions
Step by step instructions
)
for an operation
Hints and Tips
Environmental
information
John Lewis PartnershipJohn Lewis Partnership
John Lewis Partnership
John Lewis PartnershipJohn Lewis Partnership
171 Victoria Street
London SW1E 5NN
www.johnlewis.com
This appliance complies with the
following
**
*
**
**
*
**
**
*
**
4
E.E.C. Directives:E.E.C. Directives:
E.E.C. Directives:
E.E.C. Directives:E.E.C. Directives:
2006/952006/95
2006/95
2006/952006/95
(Low VoltageDirective);
2004/108 2004/108
2004/108 (Electromagnetical
2004/108 2004/108
Compatibility Directive)
90/396 90/396
90/396 (Gas Appliances)
90/396 90/396
and subsequent modifications.
;;
;
;;
,,
,
,,
Page 5
Description of the HobDescription of the Hob
Description of the Hob
Description of the HobDescription of the Hob
2
3
1
4
1.1.
1 . Hob Top
1.1.
2.2.
2 . Semi-rapid Burner
2.2.
3.3.
3 . Rapid Burner
3.3.
4.4.
4 . Auxiliary Burner
4.4.
5.5.
5 . Control knob for front left burner (auxiliary)
5.5.
6.6.
6 . Control knob for back left burner (rapid)
6.6.
7.7.
7 . Control knob for back right burner (semi-rapid)
7.7.
8.8.
8 . Control knob for front right burner (semi-rapid)
8.8.
2
8
7
6
5
5
Page 6
Instructions for the InstallerInstructions for the Installer
Instructions for the Installer
Instructions for the InstallerInstructions for the Installer
InstallationInstallation
Installation
InstallationInstallation
IMPORTANT:IMPORTANT:
IMPORTANT:
IMPORTANT:IMPORTANT:
installed according to the instruction
supplied, and by
competent personnelcompetent personnel
competent personnel to the relevant
competent personnelcompetent personnel
National Standards.
Any gas installation must be carriedAny gas installation must be carried
Any gas installation must be carried
Any gas installation must be carriedAny gas installation must be carried
out bout b
y a GAS SAFE REGISTER installery a GAS SAFE REGISTER installer
out b
y a GAS SAFE REGISTER installer
out bout b
y a GAS SAFE REGISTER installery a GAS SAFE REGISTER installer
The manufacturer will not accept liability,
should the above instructions or any of the
other safety instructions incorporated in this
book be ignored.
On the end of the shaft, which includes the
G 1/2" threaded elbow, adjustment is fixed
so that the washer is fitted between the
components as shown in the diagram. Screw
the parts together without using excessive
force.
Gas ConnectionGas Connection
Gas Connection
Gas ConnectionGas Connection
Connection to the gas supply should be with
either rigid or semi-rigid pipe, i.e. steel or
copper.
The connection should be suitable for
connecting to R 1/2” (1/2 BSP male thread).
When the final connection has been made, it
is essential that a thorough leak test is carried
out on the hob and installation.
Ensure that the main connection pipe does
not exert any strain on the hob.
This hob must be
qualified andqualified and
qualified and
qualified andqualified and
..
.
..
A)A)
A ) End of shaft with nut
A)A)
B)B)
B) Washer
B)B)
C)C)
C) Elbow
C)C)
It is important to install the elbow
correctly, with the shoulder on the end
of the thread, fitted to the hob
connecting pipe.
Failure to ensure the correct assembly
will cause leakage of gas.
When the hob is firstWhen the hob is first
When the hob is first
When the hob is firstWhen the hob is first
installedinstalled
installed
installedinstalled
Once the hob has been installed, it is
important to remove any protective
materials, which were put on in the
factory. The manufacturer will not
accept liability, should the above
instructions or any of the other safety
instructions incorporated in this book
be ignored.
6
Page 7
Engineer technical dataEngineer technical data
Engineer technical data
Engineer technical dataEngineer technical data
OO
VERALL DIMENSIONSVERALL DIMENSIONS
O
VERALL DIMENSIONS
OO
VERALL DIMENSIONSVERALL DIMENSIONS
Width: 590 mm
Depth: 520 mm
DIMENSIONS OF DIMENSIONS OF
DIMENSIONS OF
DIMENSIONS OF DIMENSIONS OF
THE HOB CTHE HOB C
THE HOB C
THE HOB CTHE HOB C
AA
VITYVITY
A
VITY
AA
VITYVITY
Width: 560 mm
Depth: 480 mm
SUPPLSUPPL
Y CONNECTIONSY CONNECTIONS
SUPPL
Y CONNECTIONS
SUPPLSUPPL
Y CONNECTIONSY CONNECTIONS
Gas:Gas:
Gas:
Gas:Gas:
R 1/2 inch (1/2 inch male) Rear right hand
corner
Electric:Electric:
Electric:
Electric:Electric:
230 V~ 50 Hz supply, 3 core flexible cable
with non rewireable plug fitted with a 3
amp cartridge fuse.
APPLIANCE CLASSAPPLIANCE CLASS
APPLIANCE CLASS 3
APPLIANCE CLASSAPPLIANCE CLASS
APPLIANCE CAPPLIANCE C
APPLIANCE C
APPLIANCE CAPPLIANCE C
GAS SUPPLGAS SUPPL
GAS SUPPL
GAS SUPPLGAS SUPPL
AA
TEGORTEGOR
A
TEGOR
AA
TEGORTEGOR
YY
Y G20 (2H) 20 mbar
YY
YY
Y II2H3+
YY
HEAHEA
TING ELEMENTS RATING ELEMENTS RA
HEA
TING ELEMENTS RA
HEAHEA
TING ELEMENTS RATING ELEMENTS RA
Rear Right BurnerRear Right Burner
Rear Right Burner 1.9 kW
Rear Right BurnerRear Right Burner
(semi rapid)(semi rapid)
(semi rapid) (6483 BTU/HR)
(semi rapid)(semi rapid)
Front Right BurnerFront Right Burner
Front Right Burner 1.9 kW
Front Right BurnerFront Right Burner
(semi rapid)(semi rapid)
(semi rapid) (6483 BTU/HR)
(semi rapid)(semi rapid)
Rear Left BurnerRear Left Burner
Rear Left Burner 2.9 kW
Rear Left BurnerRear Left Burner
(rapid)(rapid)
(rapid) (9895 BTU/HR)
(rapid)(rapid)
Front Left BurnerFront Left Burner
Front Left Burner 1.0 kW
Front Left BurnerFront Left Burner
(auxiliary)(auxiliary)
(auxiliary) (3413 BTU/HR)
(auxiliary)(auxiliary)
BurnerBurner
Burner
BurnerBurner
Auxiliary 28
Semi-rapid 32
Rapid 42
Aeration adjustment none
Dia. TapDia. Tap
Dia. Tap
Dia. TapDia. Tap
By-passBy-pass
By-pass
By-passBy-pass
1/100 mm1/100 mm
1/100 mm
1/100 mm1/100 mm
TINGTING
TING
TINGTING
TYPE OF GAS
NATURAL GAS
20 mbar
VALUE =
37.78 MJ/m
Ws - 50.7 MJ/ m
LPG GAS
28-30/37 mbar
VALUE =
49.92 MJ/Kg
3
BURNER RAPID SEMI-RAPID AUXILIARY
POSITION MA X MIN M AX MI N MAX MIN
NOMINAL THERMAL
POWER kW
NOMINAL FLOW
RATE m3/h 0.276 0.062 0.181 0.043 0.095 0.031
NOZZLE REFERENCE
3
1/100 mm
NOMINAL THERMAL
POWER kW
NOMINAL FLOW
RATE g/h
NOZZLE REFERENCE
1/100 mm
2.9 0.75 1.9 0.45 1.0 0.33
119
Adjust.
96
Adjust.
70
2.7 0.75 1.9 0.45 1.0 0.33
196 46.8 138 32.4 7 3 23.8
86 42 71 32 50 28
7
Adjust.
Page 8
Electrical ConnectionsElectrical Connections
Electrical Connections
Electrical ConnectionsElectrical Connections
THIS HOB MUST BE EARTHIS HOB MUST BE EAR
THIS HOB MUST BE EAR
THIS HOB MUST BE EARTHIS HOB MUST BE EAR
Any electrical work required to install
this hob should be carried out by a
qualified electrician or competent
person, in accordance with the current
regulations.
Electrical RequirementsElectrical Requirements
Electrical Requirements
Electrical RequirementsElectrical Requirements
Any permanent electrical installation must
comply with the latest I.E.E. Regulations and
local Electricity Board regulations. For your
own safety this should be undertaken by a
qualified electrician, e.g. your local Electricity
Board, or a contractor who is on the roll of
the National Inspection Council for Electrical
Installation Contracting (NICEIC).
Electrical ConnectionsElectrical Connections
Electrical Connections
Electrical ConnectionsElectrical Connections
This hob is designed to be connected to a 230
V 50 Hz AC electrical supply.
Before switching on, make sure the electricity
supply voltage is the same as that indicated
on the hob rating plate. The rating plate is
located on the bottom of the hob. A copy is
attached on the back cover of this book.
THEDTHED
THED
THEDTHED
Green and Yellow - Earth
..
.
..
Blue - Neutral
Brown - Live
— Connect the green and yellow
)
Upon completion there must be no cut, or
stray strands of wire present and the cable
clamp must be secure over the outer sheath.
(earth) wire to the terminal in the
plug which is marked with the letter
'E' or the earth symbol or
coloured green and yellow.
— Connect the blue (neutral) wire to
the terminal in the plug which is
marked with the letter 'N' or
coloured black.
— Connect the brown (live) wire to
the terminal in the plug which is
marked with the letter 'L' or
coloured red.
A cut off plug inserted into a 13A cut off plug inserted into a 13
A cut off plug inserted into a 13
A cut off plug inserted into a 13A cut off plug inserted into a 13
amp socket is a serious safetyamp socket is a serious safety
amp socket is a serious safety
amp socket is a serious safetyamp socket is a serious safety
(shock) hazard. Ensure that the(shock) hazard. Ensure that the
(shock) hazard. Ensure that the
(shock) hazard. Ensure that the(shock) hazard. Ensure that the
cut off plug is disposed of safcut off plug is disposed of saf
cut off plug is disposed of saf
cut off plug is disposed of safcut off plug is disposed of saf
elel
yy
..
el
y
.
elel
yy
..
The hob is supplied with a 3 core flexible
supply cables.
This has to be provided with a proper plug,
able to support the load marked on the
identification plate. To connect the plug to the
cable, follow the recommendation given in
diagram aside. The plug has to be fitted in a
proper socket.
In the event of having to change the fuse, a
3amp ASTA approved (BS 1362) fuse must
be used.
Should the plug need to be replaced for any
reason, the wires in the mains lead are
coloured in accordance with the following
code:
Permanent ConnectionPermanent Connection
Permanent Connection
Permanent ConnectionPermanent Connection
In the case of a permanent connection, it is
necessary that you install a double pole switch
between the hob and the electricity supply
(mains), with a minimum gap of 3 mm between
the switch contacts and of a type suitable for
the required load in compliance with the
current electric regulations.
The switch must not break the yellow and
green earth cable at any point.
Ensure that the hob supply cableEnsure that the hob supply cable
Ensure that the hob supply cable
Ensure that the hob supply cableEnsure that the hob supply cable
does not come into contact withdoes not come into contact with
does not come into contact with
does not come into contact withdoes not come into contact with
surfaces with temperaturessurfaces with temperatures
surfaces with temperatures
surfaces with temperaturessurfaces with temperatures
higher than 50 deg. C.higher than 50 deg. C.
higher than 50 deg. C.
higher than 50 deg. C.higher than 50 deg. C.
8
Page 9
Supply cable replacementSupply cable replacement
Supply cable replacement
Supply cable replacementSupply cable replacement
The cable used to connect the hob to the
electrical supply must comply to the
specifications given below.
Min. size Cable/flexMin. size Cable/flex
Min. size Cable/flex
Min. size Cable/flexMin. size Cable/flex
0.75 mm
The manufacturer declines any liabilityThe manufacturer declines any liability
The manufacturer declines any liability
The manufacturer declines any liabilityThe manufacturer declines any liability
should these safety measures not beshould these safety measures not be
should these safety measures not be
should these safety measures not beshould these safety measures not be
observed.observed.
observed.
observed.observed.
Wiring diagramWiring diagram
Wiring diagram
Wiring diagramWiring diagram
2
Earth (yellow/green)Earth (yellow/green)
Earth (yellow/green)
Earth (yellow/green)Earth (yellow/green)
Cable / flex typeCable / flex type
Cable / flex type
Cable / flex typeCable / flex type
H05 V2V2-F (T90) 3 A
NeutralNeutral
Neutral
NeutralNeutral
FuseFuse
Fuse
FuseFuse
9
Page 10
Fault FindingFault Finding
Fault Finding
Fault FindingFault Finding
PrPr
eliminareliminar
Pr
eliminar
PrPr
eliminareliminar
Systems CheckSystems Check
Systems Check
Systems CheckSystems Check
STARTSTART
START
STARTSTART
Isolate appliance
and carry out:
A:A:
A: Earth Continuity
A:A:
check.
y Electricaly Electrical
y Electrical
y Electricaly Electrical
Brown
Brown
Blue
Blue
Green
Green
YESYES
YES
YESYES
NONO
NO
NONO
Has inlet fuse blown?
NONO
NO
NONO
Inlet wiring
faulty.
Rectify any
fault.
Isolate appliance and
carry out:
B:B:
B: Insulation check.
B:B:
Rectify any fault
including replacing
fuses as necessary.
Carry out:
B:B:
B: Insulation
B:B:
check.
YESYES
YES
YESYES
Electricity supply
should now be
satisfactory.
A.A.
EAR EAR
A.
A.A.
Appliance must be electrically disconnected -
meter set on W (Ohms) x 1 scale and adjust
zero if necessary.
a) Test leads from any appliance earth point to
earth pin on plug. Resistance should be less than
0.1 W (Ohm), check all earth wires for continuity
and all contacts clean and tight.
B.B.
B.
B.B.
Appliance electrically disconnected, all switches
ON.
a) meter set on W (Ohms) x 1 scale. Test
leads from L to N in appliance terminal block. If
meter reads «0» then there is a short circuit.
b) meter set on W (Ohm) x 100 scale.
Repeat test with leads from L to E. If meter reads
less than ¥ (infinity) there is a fault.
NOTE - Should it be found that the fuse has
failed but no fault is indicated - a detailed
continuity check (i.e. by disconnecting and
checking each component) is required to trace
the faulty component.
It is possible that a fault could occur as a result
of local burning/arcing but no fault could be
found under test. However a detailed visual
inspection should reveal evidence of burning
around the fault.
10
TH CONTINUITY CHECKTH CONTINUITY CHECK
EAR
TH CONTINUITY CHECK
EAR EAR
TH CONTINUITY CHECKTH CONTINUITY CHECK
INSULA INSULA
INSULA
INSULA INSULA
TION CHECKTION CHECK
TION CHECK
TION CHECKTION CHECK
Page 11
Ignition System / GasIgnition System / Gas
Ignition System / Gas
Ignition System / GasIgnition System / Gas
IgnitionIgnition
Ignition
IgnitionIgnition
YESYES
YES
Ignitor does not spark
NONO
NO
NONO
YESYES
Check gas supply at
burner
Check plug top fuse and
replace if necessary
Check polarity and earth
continuity of supply point
Check earth continuity
of appliance
Check continuity from 'N' on the
mains connector block and "O" on
the ignitor unit
Check continuity from 'L' on the
mains connector block and the
taps ignition switches
Light burner manually
Check by pass simmer
adjusted
Check position of the
electrode
Check continuity from the tip of
each electrode to the terminals 1
to 4 on the ignitor unit
Check for breaks in the
insulation of the HT leads
Check fitting
of burners
Check continuity from ignition
switches connector to ignitor unit
Change the ignitor unit
11
Page 12
CommissioningCommissioning
Commissioning
CommissioningCommissioning
When the hob has been fully installed it will
be necessary to check the minimum flame
setting.
To do this, follow the procedure below.
z Turn the gas tap to the MAX position and
ignite.
z Set the gas tap to the MIN flame position
then turn the control knob from MIN to
MAX several times. If the flame is unstable
or is extinguished follow the procedure
below.
Procedure:Procedure:
Procedure:
Procedure:Procedure:
1) Re-ignite the burner and set to MIN.
)
2) Remove the control knob.
3) To adjust, use a thin bladed
screwdriver and turn the
adjustment screw (see diagram)
until the flame is steady and does
not extinguish, when the knob is
turned from MIN to MAX. Repeat
this procedure for all burners.
Minimum adjustment screwMinimum adjustment screw
Minimum adjustment screw
Minimum adjustment screwMinimum adjustment screw
Pressure testingPressure testing
Pressure testing
Pressure testingPressure testing
The pressure testing must be carried out on
the burners.
Proceed as follows:
)
1) Remove the pan supports and the
burner caps and crowns.
2) Fit manometer tube over the
injector.
3) Turn on the burner gas supply and
ignite another burner supply.
The pressure reading should be
nominally 20 mbar and must be
between 17 mbar and 25 mbar.
4) Turn off the burner supplies.
12
Page 13
Conversion from NaturalConversion from Natural
Conversion from Natural
Conversion from NaturalConversion from Natural
Gas to LPGGas to LPG
Gas to LPG
Gas to LPGGas to LPG
IMPORTANT:IMPORTANT:
IMPORTANT:
IMPORTANT:IMPORTANT:
conversion from natural gas toconversion from natural gas to
conversion from natural gas to
conversion from natural gas toconversion from natural gas to
LPG should only be undertakenLPG should only be undertaken
LPG should only be undertaken
LPG should only be undertakenLPG should only be undertaken
by a competent person.by a competent person.
by a competent person.
by a competent person.by a competent person.
It is important to note that this model is
designed for use with natural gas but can be
converted for use with butane or propane
gas providing the correct injectors are fitted.
The gas rate is adjusted to suit.
Proceed as follows:
)
1) Ensure that the gas taps are in the
'OFF' position
2) Isolate the hob from the electricity
supply
3) Remove all pan supports, burner
caps, rings, crowns and control
knobs.
4) With the aid of a 7mm box
spanner the burner injectors can
then be unscrewed and replaced
by the appropriate LPG injectors.
The replacement/The replacement/
The replacement/
The replacement/The replacement/
TT
o adjust the gas rate:o adjust the gas rate:
T
o adjust the gas rate:
TT
o adjust the gas rate:o adjust the gas rate:
With the aid of a thin bladed
screwdriver completely tighten down
the by pass adjustment screw. Upon
completion stick the replacement
rating plate on the under side of the
hob.
13
Page 14
Building inBuilding in
Building in
Building inBuilding in
IMPORTANT:IMPORTANT:
IMPORTANT:
IMPORTANT:IMPORTANT:
installed according to the instruction
supplied, and by
competent personnelcompetent personnel
competent personnel to the relevant
competent personnelcompetent personnel
National Standards.
Please ensure that when the hob is
installed it is easily accessible for the
engineer in the event of breakdown.
Building over a cupboardBuilding over a cupboard
Building over a cupboard
Building over a cupboardBuilding over a cupboard
or draor dra
or dra
or draor dra
If the hob is to be installed above a cupboard
or drawer it will be necessary to fit a heat
resistant board below the base of the hob on
the underside of the work surface.
It is also recommended to carry out the
electrical connection to the hob as shown in
diagrams 1 and 2.
ww
w
ww
erer
er
erer
This hob must be
qualified andqualified and
qualified and
qualified andqualified and
1
FLEX
OUTLET
2
ON/OFF SWITCH
ON/OFF SWITCH
14
FLEX
OUTLET
Page 15
Building over a kitchenBuilding over a kitchen
Building over a kitchen
Building over a kitchenBuilding over a kitchen
unit with doorunit with door
unit with door
unit with doorunit with door
Proper arrangements must be taken in
designing the furniture unit, in order to avoid
any contact with the bottom of the hob which
can be heated when it is operated. The
recommended solution is shown in diagram
3.
The panel fitted under the hob ("a") should
be easily removable to allow easy access if
technical assistance is needed. The space
behind the kitchen unit ("b") can be used for
connections.
Fitting the Hob into theFitting the Hob into the
Fitting the Hob into the
Fitting the Hob into theFitting the Hob into the
WW
orktoporktop
W
orktop
WW
orktoporktop
Before fitting the hob into the cut out, an
adhesive seal must be fitted to the underside
outside edge of the hob. It is essential that no
gaps are left in this seal in order to prevent
spillage near the hob seeping into the cabinet
below.
1) Remove the pan supports, the
burners caps and crowns and turn
the hob upside down, taking care
the ignition candles are not
damaged in this operation.
2) Place the sealing gasket all around
the glass top edge as shown in
diagram 4.
3) Fit the hob in the cut out and push
it down until the glass top and the
working top make contact, as
shown in diagram 5.
Dimensions are given in mm.
3
5
AA
A
AA
A)A)
A) Sealing gasket
A)A)
4
15
Page 16
ImporImpor
Impor
ImporImpor
This hob must be installed in accordance
with the Gas Safety (Installation and Use)
Regulations (Current Edition) and the IEE
Wiring Regulations (Current Edition).
For appliances installed in the Republic of
Ireland please refer to NSAI- Domestic Gas
Installation I.S. 813 Current Editions and the
ETCI Rules for Electrical Installations.
PrPr
oo
vision fvision f
Pr
o
vision f
PrPr
oo
vision fvision f
Detailed recommendations are contained in
the following British Standards Codes Of
Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S.
6891 Current Editions.
The hob should not be installed in a bed
sitting room with a volume of less than 20
m3. If it is installed in a room of volume less
than 5 m3 an air vent of effective area of 100
cm2 is required. If it is installed in a room of
volume between 5 m3 and 10 m3 an air vent
of effective area of 50 cm2 is required, while
if the volume exceeds 11 m3 no air vent is
required.
tant saftant saf
tant saf
tant saftant saf
or or
VV
entilationentilation
or
V
entilation
or or
VV
entilationentilation
ety rety r
ety r
ety rety r
equirequir
equir
equirequir
ementsements
ements
ementsements
However, if the room has a door which opens
directly to the outside no air vent is required
even if the volume is between 5 m3 and 11
m3.
If there are other fuel burning appliances in
the same room, B.S. 5440 Part 2 Current
Edition, should be consulted to determine
the requisite air vent requirements.
For appliances installed in the Republic of
Ireland please refer to the NSAI- Domestic
Gas Installation I.S. 813 Current Editions Table
Four.
16
Page 17
LocationLocation
Location
LocationLocation
The hob may be located in a kitchen, a
kitchen/diner or bed sitting room, but not in
a bathroom or shower room.
Ensure that there is a minimum distance of
55 mm between the rear cut out edge and
the wall.
A minimum distance of 450 mm must be left
between the side edges of the cut out and
any adjacent cabinets or walls.
The minimum distance combustible material
can be fitted above the hob in line with the
edges of the hob is 400 mm. If it is fitted
below 400 mm a space of 50 mm must be
allowed from the edges of the hob.
The minimum distance combustible material
or a cooker hood can be fitted above the
hob is 650 mm.
600
MIN.
17
Page 18
Instructions for the UserInstructions for the User
Instructions for the User
Instructions for the UserInstructions for the User
OperationOperation
Operation
OperationOperation
For easier lighting, proceedFor easier lighting, proceed
For easier lighting, proceed
For easier lighting, proceedFor easier lighting, proceed
before puttingbefore putting
before putting
before puttingbefore putting
support.support.
support.
support.support.
To light a burner:
)
z push in the relevant control and turn
it to maximum position.
z Upon ignition, keep the knob pushed
down about
allow the "thermocouple" (Fig. 1 -
DD
letter
D) to be heated and the safety
DD
device to be switched off, otherwise
the gas supply would be interrupted.
z Then adjust the flame as required.
z If the burner does not ignite, turn the
control knob to zero, and try again.
If the burner accidentally goes out,If the burner accidentally goes out,
If the burner accidentally goes out,
If the burner accidentally goes out,If the burner accidentally goes out,
turn the contrturn the contr
turn the contr
turn the contrturn the contr
position and wait for at least 1position and wait for at least 1
position and wait for at least 1
position and wait for at least 1position and wait for at least 1
minute before trying to light theminute before trying to light the
minute before trying to light the
minute before trying to light theminute before trying to light the
burner again.burner again.
burner again.
burner again.burner again.
Do not keep the control knobDo not keep the control knob
Do not keep the control knob
Do not keep the control knobDo not keep the control knob
pressed for more than 15pressed for more than 15
pressed for more than 15
pressed for more than 15pressed for more than 15
seconds. If the burner does notseconds. If the burner does not
seconds. If the burner does not
seconds. If the burner does notseconds. If the burner does not
light even after 15 seconds,light even after 15 seconds,
light even after 15 seconds,
light even after 15 seconds,light even after 15 seconds,
release the control knob, turnrelease the control knob, turn
release the control knob, turn
release the control knob, turnrelease the control knob, turn
it to the "off" position and waitit to the "off" position and wait
it to the "off" position and wait
it to the "off" position and waitit to the "off" position and wait
for at least 1 minute beforefor at least 1 minute before
for at least 1 minute before
for at least 1 minute beforefor at least 1 minute before
trying to light the burner again.trying to light the burner again.
trying to light the burner again.
trying to light the burner again.trying to light the burner again.
a pan on the pana pan on the pan
a pan on the pan
a pan on the pana pan on the pan
5 seconds 5 seconds
5 seconds. This will
5 seconds 5 seconds
ol knob to the ol knob to the
ol knob to the
ol knob to the ol knob to the
“off“off
“off
“off“off
””
”
””
AA
A - Burner cap
AA
BB
B - Burner crown
BB
CC
C - Ignition electrode
CC
DD
D - Thermocouple
DD
Fig. 1Fig. 1
Fig. 1
Fig. 1Fig. 1
If you use a saucepan which isIf you use a saucepan which is
If you use a saucepan which is
If you use a saucepan which isIf you use a saucepan which is
smaller than the recommendedsmaller than the recommended
smaller than the recommended
smaller than the recommendedsmaller than the recommended
size, the flame will spreadsize, the flame will spread
size, the flame will spread
size, the flame will spreadsize, the flame will spread
beyond the bottom of the vessel,beyond the bottom of the vessel,
beyond the bottom of the vessel,
beyond the bottom of the vessel,beyond the bottom of the vessel,
causing the handle to overheat.causing the handle to overheat.
causing the handle to overheat.
causing the handle to overheat.causing the handle to overheat.
TT
akak
e care car
e car
e care car
e when fre when fr
e when fr
e when fre when fr
T
ak
TT
akak
hot oil or fat, as the overheatedhot oil or fat, as the overheated
hot oil or fat, as the overheated
hot oil or fat, as the overheatedhot oil or fat, as the overheated
splashes could easily ignite.splashes could easily ignite.
splashes could easily ignite.
splashes could easily ignite.splashes could easily ignite.
ying fying f
ying f
ying fying f
ood inood in
ood in
ood inood in
18
Page 19
As soon as a liquid starts boiling, turn
down the flame so that it will barely
keep the liquid simmering.
If the control knobs become difficult
to turn, please contact your local
Service Force Centre.
When switching on the mains, after
installation or a power cut, it is quite
normal for the spark generator to be
activated automatically.
In the absence of electricity, ignition
can occur without the electrical device;
in this case, approach the burner with
a flame, push the relevant knob down
and turn it anti-clockwise until it
reaches the “maximum” position.
Using the hob correctlyUsing the hob correctly
Using the hob correctly
Using the hob correctlyUsing the hob correctly
To ensure maximum burner efficiency, it is
strongly recommended that you use only pots
and pans with a
the burner used, so that flame will not spread
beyond the bottom of the vessel (see the
table).
Use only pans or pots with flat bottom.
The stainless steel can become
tarnished if excessively heated.
Therefore prolonged cooking with
potstones, earthenware pans or castiron plates is inadvisable. Also, do not
use aluminium foil to protect the top
during use.
Make sure pots do not protrude over
the edges of the cooktop and that they
are centrally positioned on the rings
in order to obtain lower gas
consumption.
Do not place unstable or deformed
pots on the rings: they could tip over
or spill their contents, causing
accidents.
Pots must not enter the controlPots must not enter the control
Pots must not enter the control
Pots must not enter the controlPots must not enter the control
zone.zone.
zone.
zone.zone.
flat flat
flat bottom fitting the size of
flat flat
Burner minimum maximum
diameter diameter
Large (rapid) 180 mm 260 mm
Medium (semi-rapid)
rear 120 mm 220 mm
front 120 mm 220 mm
Small (auxiliary) 80 mm 180 mm
19
Page 20
Cleaning the hobCleaning the hob
Cleaning the hob
Cleaning the hobCleaning the hob
Before any maintenance orBefore any maintenance or
Before any maintenance or
Before any maintenance orBefore any maintenance or
cleaning can be carried out, youcleaning can be carried out, you
cleaning can be carried out, you
cleaning can be carried out, youcleaning can be carried out, you
must DISCONNECT the hobmust DISCONNECT the hob
must DISCONNECT the hob
must DISCONNECT the hobmust DISCONNECT the hob
frfr
om the electricity supplom the electricity suppl
fr
om the electricity suppl
frfr
om the electricity supplom the electricity suppl
The hob is best cleaned whilstThe hob is best cleaned whilst
The hob is best cleaned whilst
The hob is best cleaned whilstThe hob is best cleaned whilst
it is still warm, as spillage canit is still warm, as spillage can
it is still warm, as spillage can
it is still warm, as spillage canit is still warm, as spillage can
be removed more easily than ifbe removed more easily than if
be removed more easily than if
be removed more easily than ifbe removed more easily than if
it is left to cool.it is left to cool.
it is left to cool.
it is left to cool.it is left to cool.
This appliance cannot beThis appliance cannot be
This appliance cannot be
This appliance cannot beThis appliance cannot be
cleaned with steam or with acleaned with steam or with a
cleaned with steam or with a
cleaned with steam or with acleaned with steam or with a
steam cleaning machine.steam cleaning machine.
steam cleaning machine.
steam cleaning machine.steam cleaning machine.
yy
..
y
.
yy
..
The Hob The Hob
The Hob
The Hob The Hob
Regularly wipe over the hob top using a soft
cloth well wrung out in warm water to which a
little wasing up liquid has been added.
Avoid the use of the following:
- household detergent and bleaches;
- impregnated pads unsuitable for non-stick
saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily soiled, the
following products are recommended:
- For stainless steel hobs use a proprietary stainless
steel cleaner.
- For other hobs use Hob Brite or Bar Keepers
Friend.
Do not leave acid or alkalineDo not leave acid or alkaline
Do not leave acid or alkaline
Do not leave acid or alkalineDo not leave acid or alkaline
substances (esubstances (e
substances (e
substances (esubstances (e
lemon juice, etc.) on thelemon juice, etc.) on the
lemon juice, etc.) on the
lemon juice, etc.) on thelemon juice, etc.) on the
cooktop.cooktop.
cooktop.
cooktop.cooktop.
Pan SupportsPan Supports
Pan Supports
Pan SupportsPan Supports
The pan supports are notThe pan supports are not
The pan supports are not
The pan supports are notThe pan supports are not
dishwasher proof; they must bedishwasher proof; they must be
dishwasher proof; they must be
dishwasher proof; they must bedishwasher proof; they must be
washed bwashed b
washed b
washed bwashed b
drying them as the enamelling process
TT
opop
T
op
TT
opop
y hand.y hand.
y hand.
y hand.y hand.
.g..g.
vinegar vinegar
.g.
vinegar
.g..g.
vinegar vinegar
Take care when
,,
salt, salt,
,
salt,
,,
salt, salt,
20
Page 21
occasionally leaves rough edges. If
necessary, remove stubborn stains
using a paste cleaner.
After cleaning, make sure that the pan
supports are correctly positioned.
To keep the pan supports in the correct
position, they are mounted on metal pins
located in the lateral sides of the hob. To
ensure a better cleaning, pan supports can be
removed from the hob. Lift up the pan
suports keeping them in horizontal position
as shown in figure 2.
Avoid lifting the pan supports atAvoid lifting the pan supports at
Avoid lifting the pan supports at
Avoid lifting the pan supports atAvoid lifting the pan supports at
an angle, as this will put strainan angle, as this will put strain
an angle, as this will put strain
an angle, as this will put strainan angle, as this will put strain
on the metal pins. This mayon the metal pins. This may
on the metal pins. This may
on the metal pins. This mayon the metal pins. This may
damage the pins and cause themdamage the pins and cause them
damage the pins and cause them
damage the pins and cause themdamage the pins and cause them
to break.to break.
to break.
to break.to break.
PaPa
y attention when ry attention when r
Pa
y attention when r
PaPa
y attention when ry attention when r
pan supports in order to avoidpan supports in order to avoid
pan supports in order to avoid
pan supports in order to avoidpan supports in order to avoid
in order to avoid scratching thein order to avoid scratching the
in order to avoid scratching the
in order to avoid scratching thein order to avoid scratching the
glass hob top.glass hob top.
glass hob top.
glass hob top.glass hob top.
The BurnersThe Burners
The Burners
The BurnersThe Burners
The burner caps and crowns can be removed
for cleaning.
Wash the burners caps and crowns using hot
soapy water, and remove marks with a mild
paste cleaner. A well moistened soap
impregnated steel wool pad can be used with
caution, if the marks are particularly difficult
to remove.
eplacing theeplacing the
eplacing the
eplacing theeplacing the
YES
NO
After cleaning, be sure to wipe dry with a soft
cloth.
The Ignition electrodeThe Ignition electrode
The Ignition electrode
The Ignition electrodeThe Ignition electrode
The electric ignition is obtained through a
ceramic electrode which contains a metal
electrode (Fig. 1 components very clean, to avoid difficult
lighting, and check that the burner crown
holes (Fig. 1 -
BB
B) are not obstructed.
BB
CC
C). Keep these
CC
21
Fig. 2Fig. 2
Fig. 2
Fig. 2Fig. 2
Page 22
Something Not Something Not
Something Not
Something Not Something Not
If the hob is not working correctly, please carry
out the following checks before contacting
your local Service Force Centre.
W
WW
orking?orking?
orking?
WW
orking?orking?
SYMPT SYMPT
SYMPT
SYMPT SYMPT
There is no spark when lighting
the gas.
The gas ring burns unevenly.
If after all these checks, your hob still does
not operate correctly, contact your local
Service Force Centre.
Please note that it will be necessary to provide
proof of purchase for any in-guarantee service
calls.
OMOM
OM
OMOM
Check that the unit is plugged in and
Check that the RCCB has not
Check the mains fuse has not blown.
Check the burner cap and crown
Check the main jet is not blocked
Check the burner cap and crown
SOLUTIONSOLUTION
SOLUTION
SOLUTIONSOLUTION
the electrical supply is switched on.
tripped (if fitted).
have been replaced correctly, e.g.
after cleaning.
and the burner crown is clear of
food particles.
have been replaced correctly, e.g.
after cleaning.
In-guarantee customers should ensure that
the above checks have been made as the
engineer will make a charge if the fault is not
a mechanical or electrical breakdown.
22
Page 23
Repairs - Repairs -
Repairs -
Repairs - Repairs -
If your hob is not performing satisfactorily;
consult the fault finding guide within this
instruction book (Something not working on
the previous page). In the event of a fault
occurring which you cannot resolve yourself
from advice given within this instruction
manual.
Your first step is to contact our extended
warranty administrators on
who will give you details of your local Service
Force repair agent.
When contacting Service Force, please quote
the model (Mod.) and serial number (S.N.).
These details have been provided separately
within the pack containing this instruction
manual.
So that you always have these numbers at
hand, we recommend you to make a note of
them here:
Mod. Mod.
Mod. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mod. Mod.
PNC PNC
PNC : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PNC PNC
S.N.S.N.
S.N. : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S.N.S.N.
Your hob is covered by a 3 year parts and
labour guarantee (see separate details given
at point of sale). Please retain your purchase
receipt safely for the service engineer to verify
the purchase details.
After Sales SerAfter Sales Ser
After Sales Ser
After Sales SerAfter Sales Ser
0870 01078870870 0107887
0870 0107887
0870 01078870870 0107887
vicevice
vice
vicevice
Spare partsSpare parts
Spare parts
Spare partsSpare parts
This product should be serviced by an
authorised service engineer, and only genuine
spare parts should be used.
Under no circumstances should you attempt
to repair the hob yourself.
Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning.
Contact our extended warranty
administrators on
give you details for your local Service Force
repair agent.
Always insist on genuine spare parts.
0870 01078870870 0107887
0870 0107887 who will
0870 01078870870 0107887
23
Page 24
John Lewis PartnershipJohn Lewis Partnership
John Lewis Partnership
John Lewis PartnershipJohn Lewis Partnership
171 Victoria Street
London SW1E 5NN
www.johnlewis.com
ANC 39712-0102 04/09 R.A.
Loading...