JL Audio Slampak SB-POL-RGRRZR, Slampak SLPK-POL-RZR800, 94456 Installation Manual
I N S T A L L A T I O N G U I D E
for th e
SB-POL-RGRRZR
SKU#94456
2009+
Thank you for choosing a JL Audio Slampak® for your side by side sport utility sound system. With
proper installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening
pleasure.
We strongly recommend that you have your new Slampak
®
installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that the
Slampak
®
be properly mounted to the vehicle according to these instructions.
Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Unpack the Slampak® mount the two brackets as shown
Continued on Next Page
S T E P 2
There are two each of the pictured clamps, the ones with
the short spacers (un-assembeled in the bag) go directly
in front of the speakers, the ones with the long spacers
(assembeled on the right) are installed from below, there are
also locking pins that are not shown that are available and,
can be put in place through the clamps to keep them in the
locked positions. Make sure that all of the hardware on each
of the clamps is snug so that when the arm is pushed flat,
the rubber section of the clamp is squeezed and expands to
hold the clamp in place.
S T E P 3
Line up the brackets with the existing holes as shown in the
pictures at left and below.
SB-POL-RGRRZR INSTR_SKU# 94456
INS TALLATIO N
D I F F I C U LT Y :
25
OU T
OF
EST IMATED TIME:
12 HOU RS
Slampak
Continued on Next Page
SB-POL-RGRRZR INSTR_SKU# 94456
S T E P 7
Run the cabling to the outside of the vehicle and secure
using zip-ties as shown, make sure that there is clearence for
the seat so that when it’s in place, the cabling isn’t pinched.
S T E P 6
Plug the two jacks for the included harness into the
Stealthbox®
S T E P 5
This is seen from the rear wheel looking up and to the front,
notice the expansion clamp inserted from below going up
into the enclosure from below. This will be done on each
side then the locking pins need to go into place to secure
the clamp.
S T E P 4
once both compression clamps are in place, fold the lever
down and insert the locking pin.
Page 2 • JL Audio, Inc 2009
D e t a i l
S t e P 1 0
Remove the four screws that hold up the “belly pan” on the
Drivers side of the vehicle, secure the cabling along with the
OEM Harness along this run. When completed, re-install the
removed screws.
S t e P 9
Looking down through the battery area, run the cabling
along side the large harness seen at the bottom of the
picture towards the front of the vehicle, secure the cabling as
needed to the main cable that is right next to it.
S t e P 8
Looking back from the front, run the cabling through this
access hole near the floor and, secure it as shown in the
DETAIL picture below.
Loading...