Metal Band Saw
Metallbandsäge
2013.09
SX-815DV
Scie à ruban portable
SX-815DVP
Schweiz / Suisse
Walter Meier (TOOL) AG
Tämperlistrasse 5
CH-8117 Fällanden
Switzerland
tool-ag@waltermeier.com
www.jettools.com
France
TOOL France / PROMAC
57, rue du Bois Chaland, Z.I. du Bois Chaland
case postale 2935
FR-91029 Evry Cedex
info@promac.fr
www.promac.fr
Deutschland / Oestreich
JET Tools GmbH
Im Taubental 4
DE-41468 Neuss
team@jetgmbh.de
www.jettools.com
Diese Maschine wurde durch gemäss folgenden Richtlinien geprüft und
2
zertifiziert
- Maschinenrichtlinien
- elektromagnetische Verträglichkeit 2004/108/EC
- Niedervolt Direktiven 2006/95/EC
SGS Taiwan Ltd.
2006/42/EC
Registriernummer EZ/2009/90008C vom 29.12.2009
Registriernummer ED/2009/90011C vom 08.09.2009
Registriernummer EZ/2009/90009C vom 29.12.2008
E
SX-815DV / SX-815DVP
sofern diese gemäss der beigelegten Bedienungsanleitung gebraucht und gewartet werden, den Vorschriften betreffend Sicherheit und Gesundheit von Personen, gemäss den
oben aufgeführten Richtlinien der EG entsprechen.
La machine ci-dessous a été contrôlée et certifiée par selon les normes
suivantes
- les directives Européennes
d’enregistrement EZ/2009/90008C du 29.12.2009
- compatibilité électromagnétique 2004/108/EC
d’enregistrement ED/2009/90011C du 08.09.2009
- Directives basses tension 2006/95/EC
d’enregistrement EZ/2009/90009C du 29.12.2008
SGS Taiwan Ltd.
2006/42/EC
SX-815DV / SX-815DVP
sont, sous condition qu’elles soient utilisées et maintenues selon les instructions du
manuel d’instruction joint, conformes aux préscription sur la santé et la sécurité des
personnes, selon les directives sur la sécurité des machines mentionnées ci-dessus.
Technical file compiled by: Hansjörg Brunner, Product Management
2012-08-31 Eduard Schärer, General Manager
Walter Meier (Tool) AG, Tämperlistrasse 5, CH-8117 Fällanden, Switzerland
GB - ENGLISH
3
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new machine. This manual has been prepared
for the owner and operators of a SX-815DV / SX-815DVP metal band saw to promote safety during installation, operation and
maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read this
manual thoroughly and follow instructions carefully.
…Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
4. Machine specifications
5. Description of the machine
6. Setting up the machine
7. Commissioning
8. Choosing the saw blade
9. Maintenance
10. Environmental protection
11. Available accessories
1. Declaration of conformity
On our own responsibility we hereby declare that this
product complies with the regulations* listed on page 2.
Designed in consideration with the standards**.
2. Warranty
The Seller guarantees that the supplied product is free from
material defects and manufacturing faults. This warranty
does not cover any defects which are caused, either directly
or indirectly, by incorrect use, carelessness, accidental
damage, repair, inadequate maintenance or cleaning and
normal wear and tear.
Guarantee and/or warranty claims must be made within twelve months from the date of purchase (date of invoice). Any further claims shall be excluded.
This warranty includes all guarantee obligations of the Seller and replaces all previous declarations and agreements concerning warranties.
The warranty period is valid for eight hours of daily use. If this is exceeded, the warranty period shall be reduced in proportion to the excess use, but to no less than three months.
Returning rejected goods requires the prior express consent of the Seller and is at the Buyer’s risk and expense.
Further warranty details can be found in the General Terms and Conditions (GTC). The GTC can be viewed at www.jettools.com or can be sent by post upon request.
The Seller reserves the right to make changes to the product and accessories at any time.
3. Safety
3.1 Authorized use
This machine is designed for sawing machinable metal and
plastic materials only.
Machining of other materials is not permitted and may be
carried out in specific cases only after consulting with the
manufacturer.
Never cut magnesiumhigh danger to fire!
The workpiece must allow to safely be loaded and clamped
for machining.
The proper use also includes compliance with the operating
and maintenance instructions given in this manual.
The machine must be operated only by persons familiar with
its operation and maintenance and who are familiar with its
hazards.
The required minimum age must be observed
The machine must only be used in a technically perfect
condition.
When working on the machine, all safety mechanisms and
covers must be mounted.
In addition to the safety requirements contained in these
operating instructions and your country’s applicable
regulations, you should observe the generally recognized
technical rules concerning the operation of metalworking
machines.
Any other use exceeds authorization.
In the event of unauthorized use of the machine, the
manufacturer renounces all liability and the responsibility is
transferred exclusively to the operator.
3.2 General safety notes
Loading...