Jet Tools JTS-315SP User Manual

JTS

-

315SP

Construction

Saw

Original:

GB
Operating Instructions

Translations:

D
Gebrauchsanleitung

F
Mode d´emploi

Walter Meier (Fertigung) AG

Bahnstrasse 24
8603 Schwerzenbach
Switzerland
Phone [phone]
Fax [phone]
[e-mail]
www.jettools.com

M-10000910SM/ST 10000914M 2009-10

CE-Conformity Declaration

Product: Circular Saw Bench

JTS-315SP

Stock Number: 10000910SM, 10000910ST, 10000914M

Brand: JET

Manufacturer:

Walter Meier (Fertigung) AG, Bahnstrasse 24, 8603 Schwerzenbach, Switzerland

On our own responsibility we hereby declare that this product complies

with the regulations

* 2006/42/EC Machinery Directive
* 2004/108/EC EMC Directive (Electro Magnetic Compatibility)
* 2006/95/EC Low Voltage Directive
* 2002/95/EC RoHS Directive (Reduction of Hazardous Substances)

designed in consideration of the standards

** EN 61029-1, EN 61029-2-1

EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3

Technical file compiled by: Marcel Hofstetter, Head of Product Management

CE type examination

*** BM 60007827 0001

performed by

**** TÜV Rheinland Product Safety GmbH,

Am Grauen Stein, DE-51105 Köln ( notified body No 0197).

2009-10-30 Carl Müller, General Manager

Walter Meier (Fertigung) AG, Bahnstrasse 24, 8603 Schwerzenbach, Switzerland

2

GB - ENGLISH

Operating Instructions

Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been

prepared for the owner and operators of a JET JTS-315SP table saw to promote safety during installation, operation and
maintenance procedures. Please read and understand the information contained in these operating instructions and the
accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read
this manual thoroughly and follow instructions carefully.

…Table of Contents

1. Declaration of conformity

2. Warranty

3. Safety

Authorized use
General safety notes
Remaining hazards

4. Machine specifications
Technical data
Noise emission
Contents of delivery
Description of machine

5. Transport and start up
Transport and installation
Assembly
Dust connection
Mains connection
Starting operation

6. Machine operation

7. Setup and adjustments

Changing saw blade
Mounting the raving knife
Mounting the saw guard
Rising and tilting sawblade
Rip fence setup
Adjusting 90°stop
Adjusting sawblade parallel

8. Maintenance and inspection

9. Troubleshooting

10. Environmental protection

11. Available accessories

12. „Safe operation”........ appendix A

1. Declaration of conformity

On our own responsibility we hereby
declare that this product complies
with the regulations* listed on page

2. Designed in consideration with the
standards**. CE type examination***
performed by****.

2. Warranty

The Seller guarantees that the
supplied product is free from material
defects and manufacturing faults.
This warranty does not cover any
defects which are caused, either
directly or indirectly, by incorrect use,
carelessness, accidental damage,
repair, inadequate maintenance or
cleaning and normal wear and tear.

Guarantee and/or warranty claims
must be made within twelve months
from the date of purchase (date of
invoice). Any further claims shall be
excluded.

This warranty includes all guarantee
obligations of the Seller and replaces
all previous declarations and
agreements concerning warranties.

The warranty period is valid for eight
hours of daily use. If this is
exceeded, the warranty period shall
be reduced in proportion to the
excess use, but to no less than three
months.

Returning rejected goods requires
the prior express consent of the
Seller and is at the Buyer’s risk and
expense.

Further warranty details can be found
in the General Terms and Conditions
(GTC). The GTC can be viewed at
www.jettools.com or can be sent by
post upon request.

The Seller reserves the right to make
changes to the product and
accessories at any time.

3. Safety

3.1 Authorized use

This machine is designed for sawing
wood, wood derived materials as well
as similar to be machined hard
plastics only.
Machining of other materials is not
permitted and may be carried out in
specific cases only after consulting
with the manufacturer.

No metal workpieces may be
machined.

The workpiece must allow to safely
be loaded, supported and guided.

Do not cut round stock without
suitable jigs or fixtures. The rotating
saw blade could turn the work-piece.

The proper use also includes
compliance with the operating and
maintenance instructions given in
this manual.
The machine must be operated only
by persons familiar with its
operation, maintenance and repair
and who are familiar with its hazards.
The required minimum age must be
observed

The machine must only be used in a
technically perfect condition
When working on the machine, all
safety mechanisms and covers must
be mounted.

In addition to the safety requirements
contained in this operating
instructions and your country’s
applicable regulations, you should
observe the generally recognized
technical rules concerning the
operation of woodworking machines.

Any other use exceeds authorization.
In the event of unauthorized use of
the machine, the manufacturer
renounces all liability and the
responsibility is transferred
exclusively to the operator.

3.2 General safety notes

Woodworking machines can be
dangerous if not used properly.
Therefore the appropriate general
technical rules as well as the
following notes must be observed.

Read and understand the entire
instruction manual before attempting
assembly or operation.
Keep this operating instruction close
by the machine, protected from dirt
and humidity, and pass it over to the
new owner if you part with the tool.

No changes to the machine may be
made.

Daily inspect the function and

3