Operating Instructions and Parts Manual
10" Compound Miter Saw
Benchtop Series – Model No. JMS-10CMS
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-707100
Ph.: 800-274-6848 Revision B 04/2010
www.waltermeier.com Copyright © 2010 Walter Meier (Manufacturing) Inc.
R
CUS
174315
Warranty and Service
Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our
Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these
Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine
®
maintenance and major repair on your JET
6848.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your
local Walter Meier distributor, or visit waltermeier.com.
WARRANTY
JET products carry a limited warranty which varies in duration based upon the product (MW stands for Metalworking, WW
stands for Woodworking).
WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools, abrasives
and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general JET warranty lasts for the time period specified in the product literature of each product.
WHAT IS NOT COVERED?
Three Year, Five Year and Lifetime Warranties do not cover products used for industrial or educational purposes. Products
with Three Year, Five Year or Lifetime Warranties that are used for industrial or education purposes revert to a One Year
Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal
wear-and-tear, improper repair or alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name of the
location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise. If our
inspection discloses a defect, we will repair or replace the product, or refund the purchase price, at our option. We will return
the repaired product or replacement at our expense unless it is determined by us that there is no defect, or that the defect
resulted from causes not within the scope of our warranty in which case we will, at your direction, dispose of or return the
product. In the event you choose to have the product returned, you will be responsible for the shipping and handling costs of
the return.
HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED
WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR
INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general information and
are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice, those alterations to parts,
fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET
sold in Canada by Walter Meier.
tools. For the name of an Authorized Service Center in your area call 1-800-274-
®
branded products are not
2
Table of Contents
Warranty and Service................................................................................................................................2
Table of Contents .....................................................................................................................................3
Warnings..................................................................................................................................................4
Compound Miter Saw Safety .....................................................................................................................6
Introduction ..............................................................................................................................................7
Specifications ...........................................................................................................................................7
Cutting Capacity .......................................................................................................................................7
Electrical ..................................................................................................................................................8
Features ..................................................................................................................................................9
Shipping Contents .................................................................................................................................. 10
Assembly ............................................................................................................................................... 11
Adjustments ........................................................................................................................................... 14
Operation ............................................................................................................................................... 18
Crown Molding Chart .............................................................................................................................. 23
Maintenance .......................................................................................................................................... 24
Troubleshooting – Motor ......................................................................................................................... 25
Troubleshooting – Operation ................................................................................................................... 25
Parts ...................................................................................................................................................... 26
Wiring Diagram....................................................................................................................................... 33
The specifications in this manual are given as general information and are not binding. Walter Meier
(Manufacturing) Inc. reserves the right to effect, at any time and without prior notice, changes or alterations to
parts, fittings, and accessory equipment deemed necessary for any reason whatsoever.
Warnings
1. Read and understand the entire owners' manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This saw is designed and intended for use by properly trained and experienced personnel only. If you
are not familiar with the proper and safe operation of a compound miter saw, do not use until proper
training and knowledge have been obtained.
5. Do not use this saw for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury
that may result from that use.
6. Always wear approved safety glasses/face shields while using t his miter saw. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this saw, remove tie, rings, watches and other jewelry, and roll sleeves up past the
elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some d ust created by power sanding, sawing, grinding, drilling and other constructio n activities
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples
of these chemicals are:
• Lead from lead based paint.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area and work with approved safety
equipment, such as face or dust masks that are specifically designed to filter out microscopic
particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
16. Make sure this machine is firmly secured to the floor or bench before use.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
4
20. Don't use in dangerous environment. Don't use power tools in damp or wet locations, or expose them
to rain. Keep work area well lighted.
21. Keep visitors a safe distance from the work area. Keep children away.
22. Make your workshop child proof with padlocks, master switches or by removing starter keys.
23. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
24. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
25. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not desig ned. The right tool will do the job better and safer.
26. Use recommended accessories; improper accessories may be hazardous.
27. Maintain tools with care. Keep saw blades sharp and clean for the best and safest performance.
Follow instructions for lubricating and changing accessories.
28. Disconnect tools before servicing and when changing accessories such as blades.
29. Make sure the work piece is securely attached or clamped to the table.
30. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do
not us e your hands.
31. Do not stand on the machine. Serious injury could occur if the machine tips over.
32. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
33. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
5
Compound Miter Saw Safety
Specific safety instructions for this compound miter saw
1. Do not operate the miter saw until it is completely assembled and installed according to these
instructions.
2. If you are not thoroughly familiar with the operation of miter saws, seek guidance from your
supervisor, instructor or other qualified person.
3. Always hold the work firmly against the fence and table.
4. Do not perform any operation free hand (use clamp wherever possible).
5. Keep hands out of the path of the saw blade. If the workpiece you are cutting would cause your
hands to be within 6-3/4 in. of the saw blade, the workpiece should be clamped in place before
making the cut.
6. Be sure the blade is sharp, runs freely and is free of vibration.
7. Allow the motor to come up to full speed before starting a cut.
8. Keep the motor air slots clean and free of chips or dust.
9. Always make sure all handles are tight before cutting, even if the table is positioned in one of the
positive stops.
10. Be sure both the blade and the collar are clean and the arbor bolt is tightened securely.
11. Use only blade collars specified for your saw.
12. Never use blades larger in diameter than 10 inches.
13. Never apply lubricants to the blade when it is running.
14. Always check the blade for cracks or damage before operation. Replace a cracked or damaged blade
immediately.
15. Never use blades recommended for operation at less than 4800 RPM.
16. Always keep the blade guards in place and use at all times.
17. Never reach around the saw blade.
18. Make sure the blade is not contacting the workpiece before the switch is turned ON.
19. Important: After completing the cut, release the trigger and wait for the blade to stop before returning
the saw to the raised position.
20. Make sure the blade has come to a complete stop before removing or securing the workpiece,
changing the workpiece angle or changing the angle of the blade.
21. Never cut metals or masonry products with this tool. This miter saw is designed for use on wood and
wood-like products.
22. Never cut small pieces. If the workpiece being cut would cause your hand or fingers to be within 6-3/4
in. of the saw blade the workpiece is too small.
23. Provide adequate support to the sides of the saw table for long work pieces.
24. Never use the miter saw in an area with flammable liquids or gases.
25. Never use solvents to clean plastic parts. Solvents could possibly dissolve or otherwise damage the material.
26. Shut off the power before servicing or adjusting the tool.
27. Disconnect the saw from the power source and clean the machine when finished using.
28. Make sure the work area is clean before leaving the machine.
29. Should any part of your miter saw be missing, damaged, or fail in any way, or any electrical
component fail to perform properly, lock the switch and remove the plug from the power supply outlet.
Replace missing, damaged, or failed parts before resuming operation.
6
Introduction
This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and
maintenance procedures for the JET Model JMS-10CMS Compound Miter Saw with laser. This manual
contains instructions on installation, safety precautions, general operating procedures, maintenance
instructions and parts breakdown. This machine has been designed and constructed to provide years of
trouble free operation if used in accordance with instructions set forth in this manual. If there are any
questions or comments, please contact either your local supplier or Walter Meier. Walter Meier can also
be reached at our web site: www.waltermeier.com.
Specifications
Model Number ................................................................................................................... JMS-10CMS
Stock Number .......................................................................................................................... 707100
Motor ......................................................................................................................... 120V, 60Hz, 15A
No Load Speed (Arbor) .......................................................................................................... 4800RPM
Motor Arbor Shaft Size .................................................................................................................... 5/8"
Blade ............................................................................................................... 10", 40T, carbide tipped
Blade Arbor Size............................................................................................................................. 5/8"
Net Weight ................................................................................................................................33.3 lb.
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, Walter Meier reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
Cutting Capacity
Cutting Capacity
Cut Type Miter Angle Bevel Angle Cutting Capacity
Cross Cut 0º 0º 2-5/8" x 5-1/2" 3-1/2" x 3-1/2"
Miter 45º Right & Left 0º 2-5/8" x 3-1/2" 3-1/2" x 2"
Bevel 0º 45º Left 1-1/2" x 5-1/2" 2" x 3-1/2"
Compound Cut 45º Right & Left 45º Left 1-1/2" x 3-1/2" 2" x 2"
Vertical Capacity (Base
Board)
-- -- 4"
with 3/4"
Auxiliary Fence
Read and understand the entire contents of this manual before attempting
assembly or operation! Failure to comply may cause serious injury!
7
Electrical
Power Supply and Motor
Specifications
The AC motor used in this saw is a universal,
nonreversible type (see Motor in the Specifica-
tions section on page 7).
To avoid electrical hazards,
fire hazards, or damage to the machine, use
proper circuit protection. Your saw is wired
at the factory for 120V operation. Connect to
a 120V, 15 Amp circuit and use a 15 amp time
delay fuse or circuit breaker. If power cord is
worn or cut, or damaged in any way, have it
replaced immediately to avoid shock or fire.
Electrical Requirements
This machine is double insulated to provide a
double thickness of insulation between the user
and the machine's electrical system. All exposed
metal parts are isolated from the internal metal
motor components with protective insulation.
This saw has a plug that looks like the one
shown in Figure A.
Extension Cords
Make sure your extension cord is in good
conditio n. When usi ng a n extension cord, be
sure to use one heavy enough to carry the
current your machine will draw. An undersized
cord will ca use a drop in the line voltage
resulting in power loss and overheating. The
table below shows the correct size to use
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. Remember, the smaller the gauge
number, the heavier the cord.
Cord Length AWG
00 – 25ft 016
25 – 50ft 014
Important: Make certain the receptacle in
question is properly grounded. If you are not
sure, have a registered electrician check the
receptacle.
Figure A
To reduce the risk of electrical shock, this saw
has a polarized plug (one blade is wider than the
other). This plug will fit in a polarized outlet only
one way; if the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet.
Do not change the plug in any way.
Double insulation does not take the place of
normal safety precautions w hen operating t his
tool.
To avoid electrocution:
1. Use only identical replacement parts when
servicing a tool with double insulation.
Servicing should be performed by a qualified
technician.
2. Do not use power tools in wet or damp
locations or expose them to rain or snow.
8
Features
9
Shipping Contents
Unpacking
1. Remove the contents from the shipping
container.
2. Compare the contents of the shipping
container with the list found below. Make
certain that all items are accounted for
before discarding any packing material.
Report any shortages or damage to your
JET distributor.
Contents of the Shipping Container
A Miter Saw (1)
B Hold-down Clamp (1)
C Miter Handle (1)
E Lock Knob (2)
F Dust Bag (1)
G Extension Table (2)
H Screw (2)
-- Owner’s Manual (1)
-- Warranty Registration Card
Tools Supplied for Assembly
D Blade Wrench
Tools not included
00Adjustable Wrench
006mm Hex Wrench
00Crosspoint Screwdriver
00Combination Wrench
Read and understand all
assembly instructions before attempting
assembly! Failure to comply may cause
serious injury!
Contents of Shipping Container
10
Assembly
Releasing the Cutting Head
When not in use, lock the
cutting head in the down position. Failure to
comply can cause serious injury or damage
equipment.
Refer to Figure 1.
Unlocking
1. Push down on the switch handle (A).
2. Pull out the hold-down latch (B).
3. Raise the cutting head to the up position.
Locking
Note: When not in use, lock the cutting head in the
down position.
1. Push the cutting head down.
2. Press the hold-down latch (B) in to lock.
Important: Always use the carrying handles when
lifting or moving to avoid damage to the machine.
Installing the Extension Table
Referring to figure 2:
1. Loosen the extension table lock knob (E).
2. Place the extension mounting tube (D) into the
two holes provided in the miter saw base.
3. From underneath the saw, insert one screw (B)
into the mounting tube hole (4) and tighten.
4. Slide the extension table to desired position
and tighten the extension table lock knob (E).
5. Install the right extension table in the same
manner.
Installing the Miter Handle
Thread the miter handle (F, Fig. 2) into the hole
located at the front of the miter table.
Figure 1
Figure 2
Installing the Dust Bag
Referring to Figure 3:
1. Squeeze the metal collar wings of the dust bag (A).
2. Place the dust bag neck opening around the
exhaust port (B), and release the collar wings.
To empty the dust bag, remove from exhaust port,
open zipper on underside of bag and empty into
waste container.
Note: Check and empty bag frequently. Do not wait
for it to get full.
Figure 3
11
Installing the Safety Hold-down Clamp
1. Place the hold-down clamp assembly (A, Fig.
4) in a mounting hole located behind the right
or left (shown) fence (C).
2. Thread the hold-down clamp knob (B) into the
hole located at the rear of the saw base.
3. Tighten the hold-down clamp knob (B).
Figure 4
Table Inserts
Always unplug the saw to avoid
accidental starting. Failure to comply may
cause serious injury!
Remove table insert to remove all small pieces of
debris from the table cavity before performing
any cuts.
Be sure to reattach the table insert prior to
performing a cutting operation.
Mounting the Saw
Observe the following safety measures to avoid
injury form unexpected saw movement:
• Disconnect the power cord and lock the cutting
head in the lower position.
When lifting:
• Use the carry handle.
• Bend at the knees, not from the back.
• Clamp or bolt the saw on a level work surface.
For stationary use:
Select a location for the saw, such as the top of a
workbench, making sure to provide sufficient room for
handling the wor kpiece. Secure t he saw to the bench.
Mounting hardware is not included and must be
purchased separately.
For portable use:
Place the saw on a 3/4 in. thick piece of plywood
and bolt the base securely to the plywood using the
mounting holes on the base. Mounting hardware is
not included and must be purchased separately.
Use C-clamps to clamp this mounting board to a
stable work surface at the worksite.
Removing the Blade
Disconnect power and make
sure the switch is in the OFF position to avoid
accidental starts. Failure to comply may cause
serious injury!
Referring to Figure 5:
Do not start the saw without
checking for interference between the blade
and table insert.
Damage could result to the blade, table insert or
turntable if blade strike occurs during the cutting
operation.
To remove:
1. Loosen and remove four screws on the table
insert (see Features on page 9) with a cross-
point screwdriver
2. Remove the insert.
To install:
1. Reposition the table insert.
2. Install the four screws and tighten.
Check for blade clearance by moving the slide
carriage through the full motion of the blade in the
table slot.
1. Unplug the saw from the outlet.
2. Raise the miter saw to the upright position.
3. Raise the lower blade guard (A) to the
uppermost position.
4. While holding the lower blade guard, loosen the
cover plate screw (B) with a cross-point
screwdriver.
5. Rotate the cover plate (D) to expose t he arbor
bolt (C).
6. Place the blade wrench over the arbor bolt (C).
7. Locate the arbor lock (F) on the motor, below
the switch handle (E).
8. Press the arbor lock, holding it in firmly while
turning the blade clockwise. The arbor lock will
then engage and lock the arbor. Continue to
hold the arbor lock, while turning the wrench
clockwise to loosen the arbor bolt.
12
9. Remove the arbor bolt (H), arbor collar (J), and
blade (K). Do not remove the inner blade collar.
Note: Pay attention to the pieces removed, noting
their position and direction they face. Wipe the
blade collars clean of any sawdust before installing
a new blade.
Installing Blade
Important: This machine requires a 10-inch
diameter blade.
Unplug the miter saw before changing and/or
installing the blade.
Referring to Figure 5:
1. Install a 10-in. blade, making sure the rotation
arrow on the blade matches the clockwise
rotation arrow on the upper guard and the
blade teeth are pointing downward.
2. Place t he arbor collar (J) against the blade and
on the arbor (L). Thread the arbor bolt (H) on
the arbor in a counterclockwise direction.
Important: Make sure that the flat edge inside
opening of the arbor collar (J) is aligned with the
flat edge on the arbor shaft (L). Also, the flat-side of
the arbor collar (J) must be placed against the
blade (K).
3. Place the blade wrench on the arbor bolt (H).
4. Press the arbor lock (F), holding it in firmly
while turning the blade counterclockwise
(opposite the cutting direction of the blade).
When it engages, continue to press the arbor
lock (F) in, while tightening the arbor bolt (H)
securely.
5. Rotate the cover plate (D) back to its original
position until the slot in the cover plate engages
with the cover plate screw (B). While holding
the lower blade guard (A) up as show n, tighten
the screw (B) with a cross-point screwdriver.
The cover plate keeps the arbor bolt from falling out
if it accidentally loosens, and helps prevent the
spinning blade from coming off the saw.
6. Lower the blade guard (A) and verify that the
operation of the guard does not bind or stick.
7. Tur n the blade to disengage the arbor lock (F);
then verify that the blade will spin freely.
Never use the saw without the
cover plate secure in place. Fa ilure to comply
may cause serious injury!
Figure 5
Verify that the collars are clean
and properly installed. Lower the blade into the
table and verify that it does not come in contact
with the metal base or the turn table. Failure to
comply may cause serious injury!
13
Adjustments
Before attempting any adjustments, make sure the trigger is released and
remove the power cord from the power source
to avoid injury from unexpected starting or
electrical shock. Failure to comply may cause
serious injury!
Note: Your miter saw was adjusted at the factory.
However , during shipme nt sl ight misal ig nm ent may
have occurred. Check the following settings and
adjust if necessary prior to using this miter saw.
Bevel Stop Adjustments
To avoid injury from
unexpected starting or electrical shock, make
sure the trigger is released and remove the
power cord from the power source.
90°(0°) Bevel Adjustment
1. Set the miter angle to 0° (see Miter Angle on
page 15).
Note: A bevel angle of 0° corresponds to a blade-
to-miter-table angle of 90°.
Figure 6
2. Turn t he bevel lock handle (A, Fig. 6) clockwise
to loosen and tilt the cutting arm to the 0° bevel
angle. Turn the bevel lock handle (A)
counterclockwise to tighten.
3. Place a combination square on the miter table
with the rule against the table and heel of t he
square against the saw blade.
If the blade is not 90° to the miter table:
4. To adjust, tilt the cutting arm to 45°, loosen the
lock nut (B, Fig. 7) and turn the stop bolt (A,) in
or out accordingly.
5. Tilt the cutting arm back to the right and
recheck alignment.
6. Repeat steps 1–4 if necessary until the blade is
90° to the table, then tighten the lock nut (B,
Fig. 7) to secure the stop bolt (A, Fig. 7).
Bevel Scale Indicators
1. Set the blade to be exactly 90°(0°) to the table.
2. With cross-point screwdriver, loosen two bevel
indicator screws (B, D, Fig. 8).
3. Adjust bevel indicators (A, E, Fig. 8) to the “0”
marks (C, F, Fig. 8) on the bevel scale and
retighten the screws (B, D).
Figure 7
Figure 8
14
45° Left Bevel Positive Stop Adjustment
1. Set the miter angle to 0° (Miter Angle - page
15) and fully extend the sliding fence (Sliding
Fence - page 19) completely to the left.
2. Loosen the bevel lock handle (A, Fig. 6) and tilt
the cutting arm completely to the left.
3. Using a combination square, check to see if the
blade is 45° to the table.
If the blade is not 45° to the miter table:
4. To adjust, tilt the cutting arm to zero degrees,
loosen the lock nut (B, Fig. 9) and turn the stop
bolt (A, Fig. 9) in or out accordingly.
5. Tilt the cutting arm back to the left and rec heck
alignment.
6. Repeat steps 1–4 if necessary until the blade is
45° to the table, then tighten the lock nut (B,
Fig. 9) to secure the stop bolt (A, Fig. 9).
Miter Angle
The compound miter saw scale can be easily read,
showing miter angles from 0° to 45° to the left, and
0° to 45° to the right. The miter saw table has nine
of the most common angle settings with positive
stops at 0°, 15°, 22.5°, 31.6°, and 45°. These
positive stops position the blade at the desired
angle quickly and accurately.
Figure 9
Follow the process below for quickest and most
accurate adjustments.
Referring to Figure 10:
1. Lift up on the quick-cam miter table lock (B) to
unlock the table.
2. Lift up on the positive stop locking lever (D) and
move the turntable with handle (C) to align the
indicator (E) to the desired degree
measurement.
3. Lock the table into position by pressing down
on the quick-cam miter table lock (B).
Miter Scale Indicator Adjustment
1. Move the table to the 0° positive stop.
2. Remove the table insert (A).
3. Loosen the screw (F) that secures the indicator (E).
4. Adjust the indicator (E) to the 0° mark and
retighten screw (F).
5. Replace t he table insert (A).
Figure 10
15
Adjusting Fence Squareness
Referring to Figure 11:
1. Loosen two fence locking screws (C).
Note: O ne locking screw is located on each fence.
2. Lower the cutting arm and lock in position.
3. Using a square (B), lay the heel of the square
against the blade (D) and the ruler against the
fence (A).
4. Adjust the fence 90° to the blade and tighten
the two fence locking screws (C).
If the saw has not been used
recently, recheck blade squareness to the fence
and readjust if needed.
5. After fence has been aligned, using a scrap
piece of wood, make a cut at 90º then check
squareness on the piece. Readjust if
necessary.
Positive Stop Miter Angle Adjustment
Referring to Figure 12:
1. Unlock the miter table by lifting up on the quick-
cam miter table lock (A).
Figure 11
2. Raise the positive stop locking lever (C) up; at the
same time grasp the mi ter handle (B) and rotate
the miter table left or right to the desired angle.
3. Release the positive stop locking lever (C) and
set the miter at the desired angle making sure
the lever snaps into place.
Note: There are nine positive stops into which the
lever will lock.
4. After the angle is selected, press down on the
quick-cam miter table lock (A).
Quick-cam Miter Table Lock Operation
If a miter angle required is not one of nine positive
stops, the miter table can be locked at any angle
between these positive stops by using the quickcam miter table lock.
Referring to Figure 12:
1. Unlock the miter table by lifting up on the quick-
cam miter table lock (A).
2. Raise the positive stop locking lever (C) up; at
the same time grasp the miter handle (B) and
rotate the miter table left or right to the desired
angle.
Figure 12
3. Release the positive stop locking lever (C).
4. Press down on the quick-cam miter table lock
(A) until it locks the miter table in place.
Note: The quick-cam miter table lock should lock
the table and prevent it from moving. If adjustment
is needed, see Quick-cam Miter Table Lock
Adjustment on following page.
16
Quick-cam Miter Table Lock Adjustment
Referring to Figure 13:
1. Place the quick-cam miter lock (A) in the down
position to lock.
2. Loosen the lock nut (D) with a 13mm wrench,
then turn the stop nut (E) to extend the locking
arm against the base of the miter saw.
3. Test the quick-cam miter lock (C) to verify that
it locks the table securely into position.
4. Tighten the lock nut (D) to lock the miter
locking mechanism into place.
Laser Beam
The laser is turned on with a switch located on the
saw handle (C, Fig. 15). When left on indefinitely, a
sensor will turn the laser off after 20 minutes. The
switch must be reset (turned off for two seconds,
then on again) to restart.
The laser has no adjustments and should not
require adjustment. If adjustment should become
necessary, take t he miter saw to an approved
service center.
• Laser radiation. Avoid direct eye exposure.
Always un-plug miter saw from power
source before making any adjustments.
• Laser Warning Label: Max output <1mW
DIODE LASER: 522-542nm, Complies with
21CFR 1040.10 and 1040.11.
Figure 13
Cutting Arm Pivot Adjustment
The raising and lowering of the cutting arm should
be free of side-to-side play for accurate miter cuts.
It should be tight enough to prevent side-to-side
movement while still allowing the arm to move
freely up and down when cutting.
Referring to Figure 14:
If the cutting arm (A) is too loose, tighten by turning
the cutting arm adjusting nut (B) clockwise with a 19
mm wrench to tighten.
If cutting arm travel is too tight, turn the cutting arm
adjusting nut counterclockwise.
Use of controls or adjustments
or performance of procedures other than those
specified in this manual may result in
hazardous radiation exposure.
The use of optical instruments
with this product will increase eye hazard.
• Do not attempt to repair or disassemble the
laser. If unqualified persons attempt to
repair this laser product, serious injury may
result. Any repair required on this laser
product should be performed by authorized
service center personnel.
Figure 14
17
Operation
Before attempting any operation
with your miter saw, make sure that you have
read and thoroughly understand the warnings
contained on pages 4-5 and the Compound
Miter Saw Safety section on page 6. Failure to
comply may result in serious injury!
Starting a cut
1. Place hands at least 6-3/4 in. away from the
path of the blade.
2. Hold workpiece firmly against the fence to
prevent movement toward the blade.
3. Bring the saw blade down to the workpiece to
see the cutting path of the blade.
4. Squeeze the trigger switch (A, Fig. 15) to start
saw.
5. Lower blade into workpiece with a firm
downward motion.
Finishing a cut
1. Hold the cutting arm in the down position.
C
2. Release trigger switch (A, Fig. 15) and wait for
all moving parts to stop before moving your
hands and raising the cutting arm.
3. If the blade does not stop within 10 seconds,
unplug the saw and follow the instructions in
the Troubleshooting section.
Jammed Material
If material becomes jammed:
1. Release trigger switch.
2. Wait for all moving parts to stop.
3. Unplug the miter saw.
To Turn the Saw On
Depress the trigger switch (A, Fig. 15).
Note: Make the On/Off switch child-proof by
inserting a padlock through the hole (B, Fig. 15) in
the trigger switch.
The miter saw is equipped with an automatic blade
brake. When the trigger switch is released, t he
electric blade brake will stop the blade within
approximately 10 seconds.
Figure 15
18
Sliding Fence
The sliding fence must be
extended to the left or right when making bevel
cuts. Failure to comply may cause serious injury!
Failure to extend t he sliding fence will not allow
enough space for the blade to pass t hrough. This
could result in serious injury. At extreme miter or
bevel angles the saw blade may also contact the
fence resulting in damage to equipment as well as
personal injury.
To adjust the sliding fence (refer to Figure 16):
1. Unlock the fence cam locking lever (A) (shown
locked in Figure 16) by pushing it toward the
rear of the machine.
2. Extend the fence (B) by sliding it out (C) to
ensure that the blade will clear the fence for
degree of the bevel cut selected. Lock the
fence cam locking lever (A) as shown.
Note: Secure the sliding fence in position closest to
the saw blade when transporting the saw.
Miter Cut
Referring to Figure 17:
The sliding compound miter saw has nine positive
miter stop detents (A) located on the saw base.
The stops represent the following miter cut angles:
0, 15, 22.5, 31.6 and 45 degrees left and right. To
make a miter cut:
1. Unlock the miter table by lifting up on the quick-
cam miter table lock (E).
2. Raise the positive stop locking lever (C) up, at
the same time grasp the miter handle (D) and
rotate the miter table left or right to the desired
angle.
3. Release the positive stop locking lever (C),
making sure the lever snaps into place at one
of the miter stop detents (A).
Note: The miter can be set for any angle between
0° and 45° left and right. However, the lever will
only lock into place at one of the nine positive stops
indicated above.
Figure 16
Once the desired miter angle is achieved:
4. Press down on the quick cam miter table
lock (E) to secure the table into position.
If the miter angle desired is not one of the nine
positive stops noted above:
5. Simply lock the table at t he desired angle by
pressing down on the quick-cam miter table
lock (E).
Figure 17
19
Bevel Cut
The sliding fence must be
extended to the left when making bevel cuts.
Failure to comply may cause serious injury!
Failure to extend t he sliding fence will not allow
enough space for the blade to pass t hrough. This
could result in serious injury. At extreme miter or
bevel angles the saw blade may also contact the
fence resulting in damage to equipment as well as
personal injury.
Referring to Figure 18:
1. Loosen the bevel lock handle (B).
2. Tilt the cutting head to the desired level ranging
from 0° for a straight cut to a 45° left bevel as
displayed on the bevel scale (F).
3. Tighten the bevel lock handle (B) by pushing
down to lock the cutting head in position.
Compound Cuts
Referring to Figure 18:
Setting the bevel angle
G
1. Extend the fence (G) by sliding it out to the
required location (see Sliding Fence on page 19).
2. Loosen the bevel lock handle (B).
3. Set the desired bevel angle; then lock the bevel
lock handle (B).
Setting the miter angle
4. Unlock the miter table by lifting up on the quick-
cam miter table lock (E).
5. Raise the positive stop locking lever (C) up, at the
same time grasp the miter handle (D) and rotate
the miter table left or right to the desired angle.
6. Release the positive stop locking lever (C).
7. Lock the miter table by pressing down on the
quick-cam miter table lock (E).
Cutting Bowed Material
Always unplug the saw when
removing small pieces of debris. Failure to
comply may cause serious injury!
Referring to Figure 19:
1. Position a curved workpiece (A) against the fence (B).
Figure 18
2. Secure the curved workpiece with a clamping
device (C).
Cutting a curved workpiece without the support of
the fence and clamping device could result in
personal injury.
Figure 19
20
Repetitive Cutting
Note: Long workpieces need extension table
support.
Referring to Figure 20:
Loosen the knob (E) then slide the extension wing
(D) to desired position and tighten the knob.
The stop plate (C) is designed for use during
repetitive cutting. Simply rotate the stop plate (C) to
vertical position.
Auxiliary Wood Fence
Referring to Figure 21:
When making repetitive cuts that produce cut-off
pieces of one inch or less, it is possible for the saw
blade to catch the cut-off piece and throw it out of
the saw or into the blade guard and housing,
possibly causing damage or injury. To minimize
this, construct an auxiliary wood fence (A) to be
mounted to your saw which will provide additional
depth of cut. Mounting holes are provided on the
saw fence (B) for this purpose.
1. Construct the auxiliary wood fence (A) of a
single, straight piece of wood approximately 3/4
in. thick by 1-1/2 in. high by 22 in. long.
2. Attach the wood fence (A) securely to the saw
fence (B)
3. Make a full depth cut to create a blade slot (C).
Check for interference between the wood fence
and the lower blade guard.
4. Make adjustment if necessary.
Note: Adding a 3/4" t hick auxiliary wood fence will
also add cutting capacity (see Cutting Capacity on
page 7).
E
Figure 20
Figure 21
21
D
Cutting Base Molding
Base moldings and many other moldings can be
cut on a compound miter saw. The setup of the
saw depends on molding characteristics and
application, as shown. Perform practice cuts on
scrap material to achieve best results:
1. Always make sure moldings rest firmly against
fence and table. Use hold-down, crown molding
vise or C-clamps, whenever possible, and
place tape on the area being clamped to avoid
marks.
2. Reduce splintering by taping the cut area prior
to making the cut. Mark the cut line directly on
the tape.
3. Splintering typically happens due to an
incorrect blade application and thinness of the
material.
Note: Always perform a dry run cut so you can
determine if the operation being attempted is
possible before power is applied to the saw.
Crown Molding
Your compound miter saw is suited for the difficult
task of cutting crown molding. To fit properly, crown
molding must be compound-mitered with extreme
accuracy. The two surfaces on a piece of crown
molding that fit flat against t he ceiling and wall are
at angles that, when added together, equal exactly
90°.
Most crown molding has a top rear angle (the
section that fits flat against the ceiling) of 52°and a
bottom rear angle (the section that fits flat against
the wall) of 38°.
In order to accurately cut crown molding for a 90°
inside or outside corner, lay the molding with its
broad back surface flat on the saw table.
When setting the bevel and miter angles for
compound miters, remember that the settings are
interdependent; changing one changes the other,
as well.
Bevel/Miter Settings
Settings for standard crown molding lying flat on
compound miter saw table.
Note: The chart below references a compound cut
for crown molding only when the angle between the
walls equals 90°.
Type of Cut Key
Inside corner – Left
Side
Inside corner – Right
Side
Outside corner – Left
Side
Outside corner –
Right Side
IL 33.9° 31.6° Right 1. Position top of molding against fence.
IR 33.9° 31.6° Left 1. Position bottom of molding against fence.
OL 33.9° 31.6° Left 1. Position bottom of molding against fence.
OR 33.9° 31.6° Right 1. Position top of molding against fence.
Bevel
Setting
Miter
Setting Procedure
2. Miter table set at RIGHT 31.6°.
3. LEFT side is finished piece.
2. Miter table set at LEFT 31.6°.
3. LEFT side is finished piece.
2. Miter table set at LEFT 31.6°.
3. RIGHT side is finished piece.
2. Miter table set at RIGHT 31.6°.
3. RIGHT side is finished piece
22
Crown Molding Chart
Compound miter saw miter and bevel angle settings, wall to crown molding angles
52/38º Crown Molding 45/45º Crow n Molding 52/38º Crown Molding 45/45º Crown Molding
Angle
Between
Walls
67 42.9 3 41.08 46.89 36.13 124 18.13 21.71 20.61 19.39
68 42.3 9 40.79 46.35 35.89 125 17.77 21.34 20.21 19.06
69 41.8 5 40.50 45.81 35.64 126 17.42 20.96 19.81 18.72
70 41.3 2 40.20 45.28 35.40 127 17.06 20.59 19.42 18.39
71 40.7 9 39.90 44.75 35.15 128 16.71 20.21 19.03 18.06
72 40.2 8 39.61 44.22 34.89 129 16.37 19.83 18.64 17.72
73 39.7 6 39.30 43.70 34.64 130 16.02 19.45 18.25 17.39
74 39.2 5 39.00 43.18 35.38 131 15.67 19.07 17.86 17.05
75 38.7 4 38.69 42.66 34.12 132 15.33 18.69 17.48 16.71
76 38.2 4 38.39 42.15 33.86 133 14.99 18.31 17.09 16.38
77 37.7 4 38.08 41.64 33.60 134 14.66 17.93 16.71 16.04
78 37.2 4 37.76 41.13 33.33 135 14.30 17.55 16.32 15.70
79 36.7 5 37.45 40.62 33.07 136 13.97 17.17 15.94 15.36
80 36.2 7 37.13 40.12 32.80 137 13.63 16.79 15.56 15.02
81 35.7 9 36.81 39.62 32.53 138 13.30 16.40 15.19 14.62
82 35.3 1 36.49 39.13 32.25 139 12.96 16.02 14.81 14.34
83 34.8 3 36.17 38.63 31.98 140 12.63 15.64 14.43 14.00
84 34.3 6 35.85 38.14 31.70 141 12.30 15.25 14.06 13.65
85 33.9 0 35.52 37.66 31.42 142 11.97 14.87 13.68 13.31
86 33.4 3 35.19 37.17 31.34 143 11.64 14.48 13.31 12.97
87 32.9 7 34.86 36.69 30.86 144 11.31 14.09 12.94 12.62
88 32.5 2 34.53 36.21 30.57 145 10.99 13.71 12.57 12.29
89 32.0 7 34.20 35.74 30.29 146 10.66 13.32 12.20 11.93
90 31.6 2 33.86 35.26 30.00 147 10.34 12.93 11.83 11.59
91 31.1 7 33.53 34.79 29.71 148 10.01 12.54 11.46 11.24
92 30.7 3 33.19 34.33 29.42 149 9.69 12.16 11.09 10.89
93 30.3 0 32.86 33.86 29.13 150 9.37 11.77 10.73 10.55
94 29.8 6 32.51 33.40 28.83 151 9.05 11.38 10.36 10.20
95 29.4 3 32.17 32.94 28.54 152 8.73 10.99 10.00 9.85
96 29.0 0 31.82 32.48 28.24 153 8.41 10.60 9.63 9.50
97 28.5 8 31.48 32.02 27.94 154 8.09 10.21 9.27 9.15
98 28.1 6 31.13 31.58 27.64 155 7.77 9.82 8.91 8.80
99 27.7 4 30.78 31.13 27.34 156 7.46 9.43 8.55 8.45
100 27.3 2 30.4 3 30.6 8 27.03 157 7.14 9.04 8.19 8.10
101 26.9 1 30.0 8 30.2 4 26.73 158 6.82 8.65 7.83 7.75
102 26.5 0 29.7 3 29.8 0 26.42 159 6.51 8.26 7.47 7.40
103 26.0 9 29.3 8 29.3 6 26.12 160 6.20 7.86 7.11 7.05
104 25.6 9 29.0 2 28.9 2 25.81 161 5.88 7.47 6.75 6.70
105 25.2 9 28.6 7 28.4 8 25.50 162 5.57 7.08 6.39 6.35
106 24.8 9 28.3 1 28.0 5 25.19 163 5.26 6.69 6.03 6.00
107 24.4 9 27.9 6 27.6 2 24.87 164 4.95 6.30 5.68 5.65
108 24.1 0 27.5 9 27.1 9 24.56 165 4.63 5.90 5.32 5.30
109 23.7 1 27.2 3 26.7 7 24.24 166 4.32 5.51 4.96 4.94
110 23.3 2 26.8 7 26.3 4 23.93 167 4.01 5.12 4.61 4.59
111 22.9 3 26.5 1 25.9 2 23.61 168 3.70 4.72 4.25 4.24
112 22.5 5 26.1 5 25.5 0 23.29 169 3.39 4.33 3.90 3.89
113 22.1 7 25.7 8 25.0 8 22.97 170 3.08 3.94 3.54 3.53
114 21.7 9 25.4 2 24.6 6 22.66 171 2.77 3.54 3.19 3.10
115 21.4 2 25.0 5 24.2 5 22.33 172 2.47 3.15 2.83 2.83
116 21.0 4 24.6 8 23.8 4 22.01 173 2.15 2.75 2.48 2.47
117 20.6 7 24.3 1 23.4 3 21.68 174 1.85 2.36 2.12 2.12
118 20.3 0 23.9 4 23.0 2 21.36 175 1.54 1.97 1.77 1.77
119 19.9 3 23.5 7 22.6 1 21.03 176 1.23 1.58 1.41 1.41
120 19.5 7 23.2 0 22.2 1 20.70 177 0.92 1.18 1.06 1.06
121 19.2 0 22.8 3 21.8 0 20.38 178 0.62 0.79 0.71 0.71
122 18.8 4 22.4 6 21.4 0 20.05 179 0.31 0.39 0.35 0.35
123 18.4 8 22.0 9 21.0 0 19.72
0Mi t er
0Setting
0Bevel
0Setting
0Mi t er
0Setting
0Bevel
0Setting
Angle
Between
Walls
0Mi t er
0Setting
0Bevel
0Setting
0Mi t er
0Setting
0Bevel
0Setting
23
Maintenance
To avoid injury while
performing maintenance, always unplug the
power cord before working on the saw.
Failure to comply may cause serious injury!
Never use gasoline or any
highly volatile solvents to clean the miter
saw. Failure to comply may cause serious
injury!
Use only replacement parts
that are identical to the parts list at the end
of this manual and reassemble exactly as the
original assembly to avoid electrical shock.
Failure to comply may cause serious injury!
Replacing Carbon Brushes
Replace both carbon brushes when either has
less than 1/4 in. length of carbon remaining, or if
the spring or wire is damaged or burned.
To inspect or replace brushes:
1. Unplug the saw.
2. Remove the black plastic cap on the side of
the motor
Remove the cap cautiously, because it is springloaded.
3. Pull out the brush and replace.
4. Reverse above steps to reassemble.
Tighten the cap snugly, but do not overtighten.
Replace the brush for the other side in the same
manner described above.
Note: To reinstall the same brushes, first make
sure the brushes go back in the way they came
out. This will avoid a break-in period that
reduces motor performance and increases wear.
Lower Blade Guard
Do not use the saw without the lower blade
guard. The lower blade guard is attached to the
saw for your protection. Should the lower guard
become damaged, do not use the saw until the
damaged guard has been replaced. Develop a
regular check to make sure the lower guard is
working properly. Clean the lower guard of any
dust or buildup with a damp cloth.
When cleaning the lower
guard, unplug the saw from the power
source receptacle to avoid unexpected
startup.
Do not use solvents on the
guard. They could make the plastic “cloudy” and
brittle.
Saw Dust
Periodically, saw dust will accumulate under the
work table and base. This could cause difficulty
in the movement of the worktable when setting
up a miter cut. Frequently blow out or vacuum
up the saw dust.
If blowing saw dust, wear
proper eye protection to keep debris from
entering eyes.
Lubrication
All the motor bearings in this tool are lubricated
with a sufficient amount of high grade lubricant
for the life of t he unit under normal operating
conditions; therefore, no further lubrication is
required.
Lubricate the following as necessary:
Chop pivot: Apply light machine oil to points
indicated in illustration.
Central pivot of plastic guard: Use light
household oil (sewing machine oil) on metal-tometal or metal-to-plastic guard contact areas as
required for smooth, quiet operation. Avoid
excess ive oil, to which saw dust will cling.
24
Troubleshooting – Motor
Trouble Probable Cause Remedy
1. Motor brushes not sealed or lightly
sticking.
2. Motor brake overheated from use of
Brake does not stop
blade within 10
seconds.
Motor does not start
Brush spark when
switch released.
defective or wrong size blade or rapid
ON/OFF cycling.
3. Arbor bolt loose.
4. Brushes cracked, damaged, etc.
5. Other.
1. Limit switch failure
2. Brush worn.
3. Fuse blown or circuit breaker tripped
on home panel.
1. Worn brush.
2. Other.
Troubleshooting – Operation
1. Inspect/clean/replace brushes.
2. See MAINTENANCE section.
3. Use a recommended blade. Let cool
down. See REMOVING OR INSTALLING
THE BLADE section.
4. Retighten. See REMOVING OR
INSTALLING THE BLADE section.
5. Replace brushes.
Contact your Service Center.
1. Replace limit switch.
2. Replace brushes. See Maintenance
section.
3. Verify there is electrical power at the
outlet.
1. Replace brushes. See Maintenance
section.
2. Contact your Service Center.
Trouble Probable Cause Remedy
Blade hits table.
Angle of cut not
accurate. Can not
adjust miter.
Cutting arm wobbles. 1. Loose pivot points. 1. Contact Service Center.
Cutting arm will not
fully raise, or blade
guard won’t fully
close.
Blade binds, jams,
burns wood.
Saw vibrates or
shakes.
1. Misalignment. 1. See the Setting Cutting Depth section in
1. Miter table unlocked.
2. Saw dust under table.
1. Pivot spring not replaced properly after
service.
2. Saw dust build-up.
1. Improper operation.
2. Dull or warped blade.
3. Improper blade size.
4. Wood is moving during cut.
1. Saw blade not round / damaged /
loose.
2. Arbor bolt loose.
Adjustments
1. See the Miter Angle Adjustment section
in Operations
2. Vacuum or blow out dust.
Important: Wear eye protection.
1. Contact Service Center.
2. Clean and lubricate moving parts.
1. See Operations section.
2. Replace or sharpen blade.
3. Replace with 10 in. diameter blade.
4. Use hold down clamp to secure
workpiece to table.
1. Replace blade.
2. Tighten arbor bolt.
Laser not aligned -- 1. Contact Service Center.
Laser turns off
1. Laser turns off after 20 minutes to
prevent heat buildup.
1. Reset laser switch on trigger handle (turn
off for two seconds, then on again).
25
Parts
Ordering Replacement Parts
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for
business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available
when you call will allow us to serve you quickly and accurately.
Parts List
Note: Parts without part numbers are for reference only and cannot be purchased individually.
Index No. Part No. Description Size Qty
1 .............. JMS10CMS-1 ..........Lower Handle ..................................................................................... 1
2 .............. JMS10SCMS-10 ......Cord Clamp ........................................................................................ 1
3 .............. JMS10CMS-3 ..........Compression Spring ........................................................................... 1
4 .............. JMS10CMS-4 ..........Spring Wire ........................................................................................ 1
5 .............. JMS10CMS-5 ..........Handle Segment ................................................................................. 1
6 .............. JMS10SCMS-19 ......Blade Wrench..................................................................................... 1
7 .............. JMS10CMS-7 ..........Pan Head Tapping Screw..................................M4-18x16 ................... 2
8 .............. JMS10SCMS-88 ......Terminal............................................................................................. 2
9 .............. JMS10CMS-9 ..........Pan Head Tapping Screw..................................M6-1x25..................... 2
10 ............ JMS10SCMS-69 ......Pan Head Tapping Screw..................................M4-18x25 ................... 4
12 ............ JMS10CMS-12 ........Limit Switch ........................................................................................ 1
13 ............ JMS10CMS-13 ........Cord Guard ........................................................................................ 1
14 ............ JMS10SCMS-170 ....Rocker Switch .................................................................................... 1
15 ............ JMS10CMS-15 ........Lead Wire .......................................................................................... 1
16 ............ TS-1533062 ............Pan Head Screw...............................................M5x20........................ 1
17 ............ JMS10CMS-17 ........Upper Handle ..................................................................................... 1
18 ............ JMS10CMS-18 ........Trigger ............................................................................................... 1
19 ............ JMS10CMS-19 ........Green Laser Controller Assembly ........................................................ 1
20 ............ JMS10CMS-20 ........Pan Head Screw with Washer ...........................M6x45........................ 2
21 ............ JMS10CMS-21 ........Motor ................................................................................................. 1
22 ............ JMS10CMS-22 ........Motor Brush Cover.............................................................................. 2
23 ............ JMS10CMS-23 ........Motor Brush ....................................................................................... 2
24 ............ TS-2342161 ............Nylon Insert Lock Nut ........................................M16 ........................... 1
25 ............ TS-1541041 ............Nylon Insert Lock Nut ........................................M10 ........................... 1
26 ............ TS-155010 ..............Flat Washer......................................................M16 ........................... 2
27 ............ TS-0680041 ............Flat Washer......................................................3/8 ............................. 1
28 ............ JMS10CMS-28 ........Special Bolt ........................................................................................ 1
29 ............ JMS10CMS-29 ........Pivot Shaft ......................................................................................... 1
30 ............ TS-2171012 ............Pan Head Screw...............................................M4x6 ......................... 2
31 ............ JMS10CMS-31 ........Pin ..................................................................................................... 1
32 ............ JMS10CMS-32 ........Table ................................................................................................. 1
33 ............ JMS10CMS-33 ........Shaft .................................................................................................. 1
34 ............ JMS10CMS-34 ........O-Ring ............................................................................................... 1
35 ............ JMS10CMS-35 ........Pointer ............................................................................................... 1
36 ............ JMS10SCMS-14 ......Knob .................................................................................................. 1
37 ............ TS-2342121 ............Nylon Insert Lock Nut ........................................M12 ........................... 1
38 ............ TS-0680061 ............Flat Washer......................................................1/2 ............................. 1
39 ............ JMS10CMS-39 ........Pointer, Right ..................................................................................... 1
40 ............ JMS10CMS-40 ........Disc ................................................................................................... 1
41 ............ JMS10CMS-41 ........Pan Head Tapping Screw..................................M5-16x10 ................... 1
42 ............ TS-2360121 ............Flat Washer......................................................M12 ........................... 1
43 ............ JMS10SCMS-104 ....Bushing.............................................................................................. 1
44 ............ TS-1502051 ............Socket Head Cap Screw ...................................M5x20........................ 1
45 ............ JMS10CMS-45 ........Locking Rod ....................................................................................... 1
46 ............ TS-1540041 ............Hex Nut............................................................M6 ............................. 2
47 ............ TS-1541031 ............Nylon Insert Lock Nut ........................................M8 ............................. 1
26
Parts List
Index No. Part No. Description Size Qty
48 ............ TS-1550061 ............Flat Washer......................................................M8 ............................. 1
49 ............ TS-1533032 ............Pan Head Screw...............................................M5x10........................ 1
50 ............ JMS10CMS-50 ........Pointer ............................................................................................... 1
51 ............ JMS12SCMS-188 ....Handle ............................................................................................... 1
52 ............ TS-1482041 ............Hex Cap Screw ................................................M6x20........................ 2
53 ............ JMS10SCMS-33 ......Flat Washer......................................................1/4x1/2x3/32 .............. 1
54 ............ TS-2361061 ............Lock Washer ....................................................M6 ............................. 1
55 ............ TS-1503041 ............Socket Head Cap Screw ...................................M6x16........................ 1
56 ............ JMS10CMS-56 ........Pin ..................................................................................................... 1
57 ............ JMS10CMS-57 ........Screw Stop......................................................................................... 1
58 ............ JMS10SCMS-8 ........Nut .................................................................................................... 1
59 ............ JMS10SCMS-41 ......E-Clip ...............................................................E-6 ............................ 1
60 ............ JMS10CMS-60 ........Miter Lock Handle Assembly ............................................................... 1
61 ............ ...............................Miter Lock Handle ............................................................................... 1
62 ............ ...............................Link ................................................................................................... 1
63 ............ ...............................Shaft .................................................................................................. 1
64 ............ ...............................Spring Pin ........................................................Ø2.5x8 ....................... 2
65 ............ JMS10CMS-65 ........Compression Spring ........................................................................... 1
66 ............ TS-1541011 ............Nylon Insert Lock Nut ........................................M5 ............................. 1
67 ............ JMS10CMS-67 ........Follower Plate .................................................................................... 1
68 ............ JMS10CMS-68 ........Hex Cap Screw with Flat & Lock Washers ..........M6x16........................ 1
69 ............ JMS10CMS-69 ........Compression Spring ........................................................................... 1
70 ............ TS-1523061 ............Socket Set Screw .............................................M6x20........................ 1
71 ............ TS-1502081 ............Socket Head Cap Screw ...................................M5x35........................ 1
73 ............ JMS10CMS-73 ........Table Insert ........................................................................................ 1
74 ............ TS-2284082 ............Pan Head Screw...............................................M4x8 ......................... 4
75 ............ JMS10CMS-75 ........Bevel Arm .......................................................................................... 1
76 ............ JMS10CMS-76 ........Locking Handle Assembly ................................................................... 1
77 ............ JMS10CMS-77 ........Release/Stop Lever ............................................................................ 1
78 ............ JMS10SCMS-37 ......Wave Washer...................................................WW-8 ........................ 2
79 ............ TS-1533042 ............Pan Head Screw...............................................M5x12........................ 2
80 ............ TS-1541011 ............Nylon Insert Lock Nut ........................................M5 ............................. 2
81 ............ JMS10CMS-81 ........Extens ion Rod .................................................................................... 2
82 ............ JMS10CMS-82 ........Pan Head Screw...............................................M5x6 ......................... 2
83 ............ JMS10CMS-83 ........Stop Plate, Left ................................................................................... 1
84 ............ JMS10CMS-84 ........Extension Wing, Left ........................................................................... 1
85 ............ JMS10CMS-85 ........Extens ion Rod .................................................................................... 2
87 ............ JMS10CMS-87 ........Fence Exte ns ion ................................................................................. 1
88 ............ JMS10CMS-88 ........Fence ................................................................................................ 1
89 ............ JMS10SCMS-56 ......Socket Head Cap Screw with Washer ................M8x25........................ 1
90 ............ JMS10CMS-90 ........Socket Head Cap Screw with Washer ................M8x30........................ 2
91 ............ JMS10SCMS-17 ......Center Bolt ......................................................................................... 1
92 ............ JMS10SCMS-95 ......Knob .................................................................................................. 2
93 ............ JMS10CMS-93 ........Slide Plate.......................................................................................... 3
94 ............ JMS12SCMS-118 ....Knob .................................................................................................. 2
95 ............ JMS10CMS-95 ........Locking Handle Assembly ................................................................... 1
96 ............ ...............................Cushion ............................................................................................. 1
97 ............ ...............................Lock Ha ndle ....................................................................................... 1
98 ............ ...............................Pin ...................................................................Ø5x16 ........................ 1
99 ............ ...............................Lock Screw ........................................................................................ 1
100 .......... ...............................Plate .................................................................................................. 1
101 .......... ...............................Flat Washer......................................................M6 ............................. 1
102 .......... ...............................Nylon Insert Lock Nut ........................................M6 ............................. 1
103 .......... JMS10CMS-103 ......Extension Wing, Right ......................................................................... 1
104 .......... JMS10CMS-104 ......Stop Plate, Right................................................................................. 1
105 .......... JMS10CMS-105 ......Base .................................................................................................. 1
27
Parts List
Index No. Part No. Description Size Qty
106 .......... JMS10SCMS-54 ......Arbor Bolt ........................................................................................... 1
107 .......... JMS10CMS-107 ......Torsion Spring .................................................................................... 1
108 .......... JMS10SCMS-64 ......Truss Head Round Neck Screw .........................M6x14........................ 1
109 .......... JMS10SCMS-16 ......Guard Spring ...................................................................................... 1
110 .......... TS-1541021 ............Nylon Insert Lock Nut ........................................M6 ............................. 1
111 .......... JMS10SCMS-64 ......Truss Head Round Neck Screw .........................M6x14........................ 1
112 .......... JMS10CMS-112 ......Guard Plate ........................................................................................ 1
114 .......... JMS10CMS-114 ......Blade Guard ....................................................................................... 1
115 .......... TS-1541021 ............Nylon Insert Lock Nut ........................................M6 ............................. 1
116 .......... JMS10CMS-116 ......Saw Arm ............................................................................................ 1
118 .......... JMS10SCMS-1 ........Shaft Sleeve ....................................................................................... 1
119 .......... JMS10CMS-119 ......Lever ................................................................................................. 1
120 .......... TS-1503041 ............Socket Head Cap Screw ...................................M6x16........................ 2
121 .......... JMS10CMS-121 ......Shim .................................................................................................. 1
122 .......... TS-1503041 ............Socket Head Cap Screw ...................................M6x16........................ 1
123 .......... JMS10CMS-123 ......Anchor Block ...................................................................................... 1
124 .......... JMS10CMS-124 ......Truss Head Screw ............................................M6x8 ......................... 1
125 .......... JMS10SCMS-15 ......Coll ar ................................................................................................. 1
126 .......... TS-1534051 ............Flat Head Screw ...............................................M6x16........................ 1
127 .......... TS-1541021 ............Nylon Insert Lock Nut ........................................M6 ............................. 1
128 .......... JMS10CMS-128 ......Rubber Sleeve.................................................................................... 1
129 .......... JMS10CMS-129 ......Arbor Collar ........................................................................................ 2
130 .......... TS-1550041 ............Flat Washer......................................................M6 ............................. 1
131 .......... JMS10CMS-131 ......SHCS with Plastic Lock Washer ........................M5x35........................ 3
134 .......... TS-1523031 ............Socket Set Screw .............................................M6x10........................ 2
136 .......... JMS10CMS-136 ......Link Bracket ....................................................................................... 1
137 .......... JMS10CMS-132 ......Truss Head Screw ............................................M4x8 ......................... 3
138 .......... JMS10CMS-138 ......Cable Shield ....................................................................................... 1
139 .......... JMS10SCMS-37 ......Wave Washer...................................................WW-8 ........................ 1
141 .......... TS-1541021 ............Nylon Insert Lock Nut ........................................M6 ............................. 1
142 .......... JMS10CMS-142 ......Anchor Block ...................................................................................... 1
143 .......... TS-1503031 ............Socket Head Cap Screw ...................................M6x12........................ 1
144 .......... JMS10CMS-144 ......Clamp Hold Down Assembly ............................................................... 1
145 .......... ...............................Flange Pad......................................................................................... 1
146 .......... ...............................Clamp Hold Down Arm ........................................................................ 1
147 .......... ...............................Flat Washer......................................................M10 ........................... 1
148 .......... ...............................Flat Washer......................................................3/16 ........................... 1
149 .......... ...............................Pan Head Screw with Lock Washer ...................M5x10........................ 1
150 .......... ...............................Support Post ...................................................................................... 1
151 .......... ...............................Lock Kno b .......................................................................................... 1
152 .......... ...............................Clamp Spindle & Knob Assembly ......................................................... 1
153 .......... JMS10SCMS-90 ......Dust Bag ............................................................................................ 1
154 .......... JMS10CMS-154 ......Power Cord ........................................................................................ 1
155 .......... JMS10SCMS-192 ....Saw Blade........................................................10”x40Tx5/8” Arbor ..... 1
156 .......... JMS10SCMS-11 ......Warning Label .................................................................................... 1
157 .......... JMS10CMS-157 ......Label: Miter Quick Lock ....................................................................... 1
158 .......... JMS10SCMS-103 ....Warning Label: Avoid Exposure ........................................................... 1
159 .......... JMS10CMS-159 ......Bevel Angle Scale............................................................................... 1
160 .......... JMS10CMS-160 ......Miter Angle Scale ............................................................................... 1
161 .......... JMS10CMS-161 ......ID Label ............................................................................................. 1
162 .......... JMS10CMS-162 ......Label: Laser On/Off ............................................................................ 1
163 .......... JMS10CMS-163 ......JET Label for Handle .......................................................................... 1
164 .......... JMS10SCMS-202 ....JET Label........................................................................................... 1
165 .......... JMS10SCMS-198 ....Label: Laser Caution ........................................................................... 1
166 .......... JMS10SCMS-172 ....Label: Do Not Remove ........................................................................ 1
28
Parts List
Index No. Part No. Description Size Qty
167 .......... JMS10CMS-167 ......Label: Bevel Lock ............................................................................... 1
168 .......... JMS10SCMS-93 ......Label: Rotation ................................................................................... 1
169 .......... JMS10CMS-169 ......Cross Recessed Truss Head Tapping Screw ......M3-24x8 ..................... 1
170 .......... TS-1550021 ............Flat Washer......................................................M4 ............................. 1
171 .......... TS-1533042 ............Cross Recessed Pan Head Screw .....................M5x12........................ 4
172 .......... JMS10CMS-172 ......Cross Rec. Pan Head Round Neck Screw ..........M6x9 ......................... 1
173 .......... JMS10CMS-173 ......Laser Assembly .................................................................................. 1
174 .......... JMS10CMS-174 ......Cross Recessed Truss Head Screw ...................M4x10........................ 4
175 .......... JMS10CMS-175 ......Cover ................................................................................................. 2
176 .......... JMS10CMS-176 ......Slotted Set Screw .............................................M6x8 ......................... 4
177 .......... JMS10CMS-177 ......Flat Washer......................................................M5x14-T1................... 4
178 .......... JMS10CMS-178 ......Bracing Plate ...................................................................................... 2
179 .......... JMS10CMS-179 ......Laser Plunger Housing ........................................................................ 1
29
Assembly Drawing
30
Assembly Drawing (continued)
31
Assembly Drawing (continued)
32
Wiring Diagram
33
Notes
34
Notes
35
40
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.waltermeier.com
Loading...