Operating Instructions and Parts Manual
Lever-Operated Chain Hoist
JLH Compact Series 0.25T and 0.5T
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-181205
Ph.: 800-274-6848 Revision C 09/2015
www.jettools.com Copyright © 2015 JET
Warranty and Service
JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please
contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.
Warranty Period
The general warranty lasts for the time period specified in the literature included with your product or on the official
JET branded website.
• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)
• Accessories carry a limited warranty of one year from the date of receipt.
• Consumable items are defined as expendable parts or accessories expected to become inoperable within a
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.
Who is Covered
This warranty covers only the initial purchaser of the product from the date of delivery.
What is Co vered
This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty
does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear,
improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood.
Use of these machines in the processing of metal, plastics, or other materials may void the warranty. The exceptions
are acrylics and other natural items that are made specifically for wood turning.
Warranty Limitations
Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a
Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof
of initia l p u rch a s e whe n calling. If a product requires further inspection, the Technical Service representative will
explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the
United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service
Center Locator on the JET website.
More Informa tion
JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor
or visit the JET website.
How State Law Appli es
This warranty gives you specific legal rights, subject to applicable state law.
Limitations on This Warranty
JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT.
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR
INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are
given as general information and are not binding. JET reserves the right to effect at any time, without prior notice,
those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason
whatsoever. JET
Product Listing with Warranty Period
90 Days – Parts; Consumable items
1 Year – Motors; Machine Accessories
2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used
for industrial or commercial purposes
5 Year – Woodworking Machinery
Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools
NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries,
Inc., or any of its successors in interest to the JET brand.
®
branded products are not sold in Canada by JPW Industries, Inc.
2
Table of Contents
Warranty and Service ............................................................................................................................................ 2
Table of Contents .................................................................................................................................................. 3
Warning ................................................................................................................................................................. 4
Introduction ........................................................................................................................................................... 5
Specifications (JLH-25/50) .................................................................................................................................... 6
Unpacking ............................................................................................................................................................. 7
Contents of the Carton ...................................................................................................................................... 7
Installation ............................................................................................................................................................. 7
Pre-Operation Inspection ...................................................................................................................................... 7
Inspecting the Load Chain ................................................................................................................................. 7
Inspecting Hooks ............................................................................................................................................... 8
Other Inspections .............................................................................................................................................. 8
Operation .............................................................................................................................................................. 8
Precautions ....................................................................................................................................................... 9
Inspection and Maintenance ................................................................................................................................. 9
Allowable Limits for Load Chain and Hooks ........................................................................................................ 10
Load Chain ...................................................................................................................................................... 10
Hooks (Top and Bottom) ................................................................................................................................. 10
Troubleshooting .................................................................................................................................................. 11
Replacement Parts .............................................................................................................................................. 11
JLH Compact Series Lever Hoists (JLH-25/50) .............................................................................................. 12
Parts List: JLH-25 (0.25 Ton) .......................................................................................................................... 13
Parts List: JLH-50 (0.5 Ton) ............................................................................................................................ 14
3
Warning
1. Read and understand the entire owner’s manual before attempting operation. Failure to comply with
instructions and warnings may cause serious injury.
2. This lever hoist is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a lever hoist, do not use until proper training and
knowledge have been obtained.
3. Do not use this lever hoist for other than its intended use. If used for other purposes, JET disclaims any
real or implied warranty and holds itself harmless from any injury that may result from that use.
4. Do not use lever hoist to lift, support or transport people; or to lift or support loads over people.
5. Do not exceed the rated capacity of the hoist.
6. Do not attempt to extend the lever handle using a “cheater pipe” or any other such device.
7. Do not strike the lever handle with a hammer or any other object.
8. Do not use the chain as a sling. This may cause damage to the chain.
9. Always inspect the lever hoist for damage prior to use. If hoist is damaged, do not use until it has been
repaired or replaced.
10. Do not use more than one lever hoist to lift or move a load. If this is unavoidable, each hoist must have the
same capacity as the load to be moved.
11. Never allow chain to “set” over sharp edges. All pulls or lifts must be made with straight chain that is free of
obstacles.
12. If the lever handle is difficult to operate, then the load exceeds the capacity of the hoist. Reduce load or
select a hoist of larger capacity.
13. Do not use hoist if the chain is twisted, kinked or damaged.
14. Do not operate hoist unless load is centered between top and bottom hooks.
15. On hoists with the overload warning lever, do not use this device to measure load weight.
16. Always take time to study the job to be performed and choose the safest method. Do not place yourself or
other people in an unsafe position.
17. Always maintain your balance and firm footing when operating the lever hoist.
18. Leave all internal maintenance and inspections to a qualified JET Service Center.
19. Do not attempt to lengthen or repair load chain.
20. Replace chain with factory replacement chain only. Do not use any other type of chain.
21. If welding near the hoist, do not allow the chain or hook to be touched by a live electrode. Prevent weld
splatter upon the chain.
22. Never use the hoist if either hook is stretched, deformed, or has a broken or missing safety latch. Always
replace the safety latch and/or the hook before placing the hoist back in service.
23. Be sure supporting structures and load-attaching devices used in conjunction with this lever hoist provide
an adequate safety factor to handle the rated load plus the weight of the equipment. If in doubt, consult a
qualified structural engineer.
24. Understand and follow all procedures as set forth in American National Standards titled “Performance
Standard for Manually Lever Operated Chain Hoists” (ANSI/ASME HST-3) and “Manually Lever Operated
Hoists” (ANSI/ASME B30.21). These standards are available through the American Society of Mechanical
Engineers, Three Park Ave., New York, NY 10016, or visit www.ASME.org
25. Keep visitors a safe distance from the work area. Keep children away.
4
Introduction
This manual is provided by JET covering the safe operation and maintenance procedures for the JET JLH
Compact Series Lever Hoists. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. This tool has been designed and
constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this
manual. If there are any questions or comments, please contact either your local supplier or JET. JET can also
be reached at our web site: www.jettools.com.
The JLH Compact Series Lever Hoists comply with OSHA regulations, ANSI/ASME B30.21 and HS T-3
Standards.
Record your purchase information here for quick reference:
Model No.: Stock No.: Serial No.:
Purchased From: Date Purchased:
5
Specifications (JLH-25/50)
width
(in.)
“D”
Hook
Throat
Opening
(in.)
“E”
Net
Weight
(lbs)
Min.
Distance
Stock
Number Description
181205 JLH-25-5 0.25 5 1.40 1 3.2 0.42 44.97 5.71 2.68 3.43 0.83 3.53
181210 JLH-25-10 0.25 10 1.40 1 3.2 0.42 44.97 5.71 2.68 3.43 0.83 4.41
181215 JLH-25-15 0.25 15 1.40 1 3.2 0.42 44.97 5.71 2.68 3.43 0.83 5.29
181505 JLH-50-5 0.5 5 1.65 1 4.3 0.33 54.01 6.30 3.19 3.96 0.96 5.51
181510 JLH-50-10 0.5 10 1.65 1 4.3 0.33 54.01 6.30 3.19 3.96 0.96 7.05
181515 JLH-50-15 0.5 15 1.65 1 4.3 0.33 54.01 6.30 3.19 3.96 0.96 8.60
Rated
Capcty.
(ton)
Standard
Lift
(ft.)
between
hooks (in.)
“A”
No.
of
falls
Load
Chain
Diameter
(mm)
Lift per
full turn
(in.)
Lbs.
Pull
to Lift
capacity
Lever
Length
(in.)
“B”
Overall
(in.)
“C”
NOTE: The above stock numbers are representative; chain is available in other lengths. Specify length when
ordering.
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
6
Unpacking
Pre-Operation Inspection
Open carton and check for shipping damage.
Report any damage immediately to your distributor
and shipping agent. Do not discard any shipping
material until the Lever Hoist is assembled and
running properly. Read this entire instruction
manual thoroughly for set-up, maintenance and
safety instructions.
Contents of the Carton
1 Lever Hoist
1 Carry Pouch
1 Owner's Manual
1 Warranty Card
Inspecting the Load Chain
1. A chain stop must be attached to the secondto-last link on the slack end of the chain. See
Figure 2.
Figure 2
Do not operate the hoist with a
twisted, kinked or damaged chain. Do not
splice the chain.
2. Check that the chain does not twist along its
length from hoist to hook. If twist is present on
units with multiple falls, the hook must be
passed back through the chain loop to remove
all twist in the chain.
Figure 1
Features and terminology
Installation
Support for the hoist may be hook, clevis pin,
trolley, or beam clamp. Whatever method of
suspension is chosen, the support components
must be rated equal to, or greater than the
capacity of the lever hoist. Supporting structures
(such as I-Beams, etc.) should be installed by
properly licensed professional installers.
3. Replace the chain if links are stretched too
long or seriously worn on the surface,
especially at the points where links contact
each other. See “Allowable Limits” on page 12
for measuring chain elongation.
4. Do not use a chain that is seriously rusted or
cracked.
5. Periodically apply a light coat of 30W oil to the
chain. This will create easier operation and
prolong the chain’s life. For optimum results,
clean the chain with an acid-free solution
before oiling.
The load chain supplied with
your JET lever hoist is designed,
manufactured, and tested for proper fit and
durability. If chain should ever need replaci ng,
for your own safety use factory replacement
chain only. Use of other than factory
replacement chain may cause serious injury
and/or damage to the lever hoist.
Never extend load chain by welding a second
piece to the original.
7
Inspecting Hooks
Operation
It is important to check top and bottom hooks for
proper opening and other signs of deformation or
damage. Replace a hook immediately if any of the
following problems are identified:
• The safety latch no longer contacts the hook
opening.
• The vertical angle at the neck of the hook
reaches 10° (see Figure 3).
Figure 3
• Chemical corrosion or cracks on the hook.
• Excessive wear on the inside surface.
The JLH Mini Lever Hoist may be used either in
vertical position as a hoist; or in angled or
horizontal position as a puller. Below is the general
procedure for operating the hoist:
1. Set the top hook securely.
2. Correctly center the load on the bottom hook
(Figure 4). Incorrect loading is dangerous to
the operator, the lever hoist, and the load.
• Never load the hook in front of the safety
latch (A, Figure 5).
• Never load the hook tip (B, Figure 5).
• Never load the hook off the centerline (C,
Figure 5).
• Never load the hook sideways (D, Figure
5).
• The throat opening has enlarged. (See page 12
for the maximum allowable limits for the throat
opening.)
Do not attempt repair of a hook
by heat treating, bending or attaching anythi ng
by welding. Such procedures will weaken and
may cause failure of the hook.
Other Inspections
1. Check for appropriate clicking sounds: With
the selector lever in UP position, there will be a
clicking sound when the lever handle is rotated
in either direction. When the selector lever is in
DOWN position, there will be a clicking sound
only when the lever handle is ratcheted back
into position but not as the load is lowered. If
these sounds are not present, or if irregular
clicking noises develop, do not use the hoist –
have it inspected and repaired by an
authorized service center.
2. If the lever hoist has not been used for an
extended period of time, check for proper
operation before putting into service.
3. The brake mechanism must be kept clean and
free from dirt, water, and oil. Never allow oil to
penetrate the braking mechanism. The brake
should not slip while using the hoist.
Figure 4
Figure 5
3. Rotate the handwheel clockwise while
simultaneously pulling down on the load chain.
The handwheel will snap back into place, reengaging the gear.
4. Move selector switch to the UP position.
Ratchet the lever to raise or pull the load. Do
not overload the lever hoist.
8
Do not touch the handwheel
while lifting or lowering. Do not operate
freewheel mode while there is a load on the
hoist.
5. To release or lower the load, turn selector
switch on the handle to the DOWN position
and ratchet the handle.
NOTE: If the chain is pulled too suddenly in freewheel mode, the brake may set preventing further
pulling. Re-set the hoist by repeating step number
3 above, and then set the hoist back into freewheel
mode to continue the operation.
Avoid lifting one load with two hoists. If this is
unavoidable, apply equal weight to both hoists and
use hoists with the proper lift capacity. Capacity of
each hoist must be equal to the total load to be
lifted.
Precautions
• During lifting operations, do not stand under
the load.
• Do not use any extension on the lever handle.
Do not use your foot to apply pressure to the
lever handle.
• Prevent the chain from dragging over sharp
edges or corners. This will cause links to
weaken, bend, or break.
• When connecting to a wire rope sling, the lever
hoist must be applied along a straight line
parallel to the surface on which it is resting.
See Figure 6.
• When lifting loads, hook the load with slings.
Do not use the lever hoist chain as a sling
(Figure 7).
• Both ends of a sling or rope must be
completely on the inside of the safety latch
before pulling or lifting the load. Do not put
one end on the inside of the latch and leave
the other end on the hook end outside the
latch.
Figure 7
Inspection and Maintenance
Read and follow ANSI Inspection and Maintenance
Instructions. Know the meaning of Frequent
Inspection, Periodic Inspection, Normal Service,
Heavy Service, and Severe Service. It is the
customer’s responsibility to understand and follow
all ANSI and JET inspection and maintenance
instructions.
Figure 6
The lever hoist should be stored in a clean, dry
environment. Clean and oil the hoist before
storage.
Hoists that are installed out-of-doors should be
covered or brought inside when not in use.
Periodically apply a light coat of 30W oil to the load
chain. Also lubricate the safety latches and the
bearings in the hooks.
Annually, the hoist should be disassembled,
inspected, and cleaned by trained and experienced
personnel only. Contact a JET authorized service
center by calling your dealer or visiting our web site
at jettools.com.
9
Allowable Limits for Load Chain and Hooks
Load Chain
Carefully inspect the entire load chain. As
illustrated in Figure 8, measure five consecutive
links with calipers to find the length, Compare the
results with the table in Figure 8. Check every
three feet and especially where excessive wear is
indicated. Any load chain that shows noticeable
deformation or heat influence must be replaced
with a new one.
Never extend load chain by
welding a second piece to the original.
Hoist
Capacity
0.25 ton 45 46.3
0.5 ton 60 61.8
5 Links Normal
(mm)
Figure 8
5 Links Limit
Replace if ≥
Hooks (Top and Bottom)
Replace the hook when the distance between
indicator points – “A” in Figure 9 – is wider than the
limits given in the table.
Never heat treat the hook or attach anything to the
hook by welding.
Hoist
Capacity
0.25 ton 35.5 37.3
0.5 ton 41 43.1
“A” Dimension
Normal
(mm)
Figure 9
“A” Dimension
Replace if ≥
10
Troubleshooting
The numbers in parentheses refer to the parts breakdown on the following page.
Trouble Probable Cause Remedy*
Hoist will not lift (no
clicking sound).
Load slips or drifts
while being lowered.
Hoist will not lower
load.
Hoist will not
freewheel.
Pawl (#21) not engaging ratchet disc
(#24); possible dirt or foreign material.
Pawl spring (#20) is damaged. Replace pawl spring.
Selector switch spring is loose or
damaged.
Dirt/corrosion/foreign material in hoist
components.
Brake is slipping. Brake seat (#23) is
worn from long-term use, or is damaged
from overloading or misuse.
The brake has caught. (Hoist was left
under load condition for extended
period, or was shock-loaded while
operating.)
Brake components are corroded or
damaged.
Brake has caught because load chain
was pulled too hard.
Clean and lubricate pawl/ratchet disc
assemblies.
Tighten or replace selector switch
spring.
Inspect and correct problem. Keep hoist
clean and lubricated.
Replace disc hub. Do not overload
hoist.
Place selector lever in DOWN position
and pull hard on the lever handle to reset the brake. Resume operation.
Replace components as needed; keep
hoist clean and lubricated.
Reset by rotating handwheel clockwise
while pulling down on load chain.
Return hoist to freewheel mode and
continue. Pull load chain less forcibly.
* Any disassembly or repair of the lever hoist should be performed by properly trained personnel. Call JET or
go to www.jettools.com to find an authorized Service Center nearest you.
Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com). Having the
Model Number and Serial Number of your machine available when you call will allow us to serve you quickly
and accurately.
11
JLH Compact Series Lever Hoists (JLH-25/50)
12
Parts List: JLH-25 (0.25 Ton)
Parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH25-1G .................. Top Hook Assembly................................................. ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch Kit........................................................ ...................................... 1
.................. .................................. Top Hook Holder...................................................... ...................................... 1
2 ................ JLH25-2..................... Safety Latch Kit........................................................ ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... ...................................... 2
.................. .................................. Lock Nut................................................................... ...................................... 2
3 ................ JLH25-3..................... Top Hook Shaft ........................................................ ...................................... 1
4 ................ JLH25-4G .................. Bottom Hook Assembly ........................................... ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 1
.................. .................................. Safety Latch Kit........................................................ ...................................... 1
5 ................ JLH25-5..................... Chain pin and Lock Nut ........................................... M4 ................................. 1
7 ................ JLH25-6G .................. Gear Cover Set ........................................................ ...................................... 1
8 ................ JLH25-8..................... Reinforced Plate ...................................................... ...................................... 1
9 ................ JLH25-9..................... Load Gear ................................................................ ...................................... 2
10 .............. JLH25-10................... Pinion Shaft ............................................................. ...................................... 1
11 .............. JLH25-11................... Gear Side Plate ....................................................... ...................................... 1
12 .............. JLH25-12................... Chain Stripper .......................................................... ...................................... 1
13 .............. JLH25-13................... Stay Bolt .................................................................. ...................................... 2
15 .............. JLH25-15................... Load Sheave Assembly ........................................... ...................................... 1
18 .............. JLH25-18................... Chain G uide ............................................................. ...................................... 2
19 .............. JLH25-19................... Lever Side Plate Assembly ...................................... ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Pawl Pin ................................................................... ...................................... 2
20 .............. JLH25-20................... Pawl Spring (0.25,0.5 ton) ....................................... ...................................... 2
21 .............. JLH25-21................... Pawl (0.25,0.5 ton)................................................... ...................................... 2
22 .............. JLH25-22................... Snap Ring (0.25,0.5 ton).......................................... 6mm .............................. 2
23 .............. JLH25-23................... Brake Seat ............................................................... ...................................... 1
24 .............. JLH25-24................... Ratchet Disc ............................................................ ...................................... 1
25 .............. JLH25-25................... Friction Disc ............................................................. ...................................... 2
26 .............. JLH25-26................... Twisting Spr ing ........................................................ ...................................... 1
27 .............. JLH25-27................... Brake Plate .............................................................. ...................................... 1
28 .............. JLH25-28................... Bushing .................................................................... ...................................... 1
29 .............. JLH25-29................... Stop Knob ................................................................ ...................................... 1
30 .............. JLH25-30G ................ Brake Cover ............................................................. ...................................... 1
31 .............. JLH25-31G ................ Socket Head Screw and Spring Washer ................. M5x40 and 5mm ........... 3
33 .............. JLH25-33................... Snap Ri ng ................................................................ 9mm .............................. 1
34 .............. JLH25-34................... Change Over Gear .................................................. ...................................... 1
35 .............. JLH25-35................... Lever Handle Assembly ........................................... ..............
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Level .......................................................... ...................................... 1
.................. .................................. Change Over Pawl................................................... ...................................... 1
.................. .................................. Snap Ring ................................................................ 6mm .............................. 1
.................. .................................. Roller ....................................................................... Ø5mm ........................... 1
.................. .................................. Change Over Spring ................................................ ...................................... 1
36 .............. JLH25-36................... Snap Ri ng ................................................................ 22mm ............................ 1
37 .............. JLH25-37G ................ Handwheel ............................................................... ...................................... 1
38 .............. JLH25-38................... Snap Ri ng ................................................................ 7mm .............................. 1
40 .............. JLH25-40................... Rubber Grip ............................................................. ...................................... 1
41 .............. JLH25-41................... Bolt and Locking Nut (0.25,0.5 ton) ......................... M3.5 .............................. 1
48 .............. JLH25-48................... Load Chain – specify length .................................... 3.2x9 mm ...................... 1
49 .............. JLH25-49................... End Chain Ring........................................................ ...................................... 1
50 .............. JLH25-50................... Carry Pouch for JLH-25 (not shown) ....................... 95x70x180mm .............. 1
.................. LM000040 ................. Name Plate JLH-25 (not shown).............................. ...................................... 1
Note: All parts mentioned as assembly are sold as an assembly only.
When ordering replacement chain (#48), specify length.
........................ 1
13
Parts List: JLH-50 (0.5 Ton)
Parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH50-1G .................. Top Hook Assembly................................................. ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch Kit........................................................ ...................................... 1
.................. .................................. Top Hook Holder...................................................... ...................................... 1
2 ................ JLH50-2..................... Safety Latch Kit........................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... ...................................... 2
.................. .................................. Lock Nut................................................................... ...................................... 2
3 ................ JLH50-3..................... Top Hook Shaft ........................................................ ...................................... 1
4 ................ JLH50-4G .................. Bottom Hook Assembly ........................................... ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 1
.................. .................................. Safety Latch Kit........................................................ ...................................... 1
5 ................ JLH50-5G .................. Chain Pin & Lock Nut............................................... ...................................... 1
7 ................ JLH50-7G .................. Gear Cover Set ........................................................ ...................................... 1
8 ................ JLH50-8..................... Reinforced Plate ...................................................... ...................................... 1
9 ................ JLH50-9..................... Load Gear ................................................................ ...................................... 2
10 .............. JLH50-10................... Pinion Shaft ............................................................. ...................................... 1
11 .............. JLH50-11................... Gear Side Plate ....................................................... ...................................... 1
12 .............. JLH50-12................... Chain Stripper .......................................................... ...................................... 1
13 .............. JLH50-13................... Stay Bolt .................................................................. ...................................... 2
14 .............. JLH50-14................... Pin............................................................................ ...................................... 1
16 .............. JLH50-16................... Load Sprocket.......................................................... ...................................... 1
17 .............. JLH50-17................... Load Gear ................................................................ ...................................... 1
18 .............. JLH50-18................... Chain G uide ............................................................. ...................................... 2
19 .............. JLH50-19................... Lever Side Plate Assembly ...................................... ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Pawl Pin ................................................................... ...................................... 2
20 .............. JLH25-50................... Pawl Spring (0.25,0.5 ton) ....................................... ...................................... 2
21 .............. JLH25-21................... Pawl (0.25,0.5 ton)................................................... ...................................... 2
22 .............. JLH25-22................... Snap Ring (0.25,0.5 ton).......................................... 6mm .............................. 2
23 .............. JLH50-23................... Brake Seat ............................................................... ...................................... 1
24 .............. JLH50-24................... Ratchet Disc ............................................................ ...................................... 1
25 .............. JLH50-25................... Friction Disc ............................................................. ...................................... 2
26 .............. JLH50-26................... Twisting Spr ing ........................................................ ...................................... 1
27 .............. JLH50-27................... Brake Plate .............................................................. ...................................... 1
28 .............. JLH50-28................... Bushing .................................................................... ...................................... 1
29 .............. JLH50-29................... Stop Knob ................................................................ ...................................... 1
30 .............. JLH50-30G ................ Brake Cover ............................................................. ...................................... 1
31 .............. JLH50-31G ................ Socket Head Screw & Spring Washer ..................... M6x45 & 6mm ............... 3
34 .............. JLH50-34................... Change Over Gear .................................................. ...................................... 1
35 .............. JLH50-35................... Lever Handle Assembly ........................................... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Pawl................................................... ...................................... 1
.................. .................................. Snap Ring ................................................................ 6mm .............................. 1
.................. .................................. Roller ....................................................................... Ø5mm ........................... 1
.................. .................................. Change Over Spring ................................................ ...................................... 1
36 .............. JLH50-36................... Snap Ri ng ................................................................ 25mm ............................ 1
37 .............. JLH50-37G ................ Handwheel ............................................................... ...................................... 1
38 .............. JLH50-38................... Snap Ri ng ................................................................ 7mm .............................. 1
40 .............. JLH50-40................... Rubber Grip ............................................................. ...................................... 1
41 .............. JLH25-41................... Bolt & Locking Nut (0.25, 0.5 ton) ............................ M3.5 .............................. 1
48 .............. JLH50-48................... Load Chain – specify length .................................... 4.3x12mm ..................... 1
49 .............. JLH50-49................... End Chain Ring........................................................ ...................................... 1
50 .............. JLH50-50................... Carry Pouch for JLH-50 (not shown) ....................... 100x75x200mm ............ 1
.................. LM000041 ................. Name Plate JLH-50 (not shown).............................. ...................................... 1
Note: All parts mentioned as assembly are sold as an assembly only.
When ordering replacement chain (#48), specify length.
14
This page intentionally left blank.
15
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.jettools.com
16
Loading...