JET JJP-10BTOS 10” Jointer-Planer with Stand
Designed with the space limitations faced by many of
today’s woodworkers, the JET 10" Jointer/Planer packs
the capabilities of the jointer and planer into a single,
space-saving footprint. Combining the jointer and planer,
two of the most-used core woodworking machines also
saves money.
Power with Precision
The JET 10" Jointer/Planer is powered by a 13A, 120V
(only) motor. A paddle-style switch controls the motor.
This switch has a removable “key” that helps prevent
usage of the machine when you are not present. A push
button next to the paddle switch resets the automatic
thermal protection circuit.
The motor power is delivered to the cutterhead with a
drive belt for smooth, consistent operation. The
cutterhead spins at 9000 RPM to give the best overall
performance with the various wood species and grain
types you may encounter. The motor also powers the
feed rollers for the planning function using a chain drive.
The entire drive system is enclosed within a housing that
keeps you safe while helping to protect the mechanism
from dust contamination.
Knife System
The precision machined, all-steel
cutterhead is equipped with two high-quality knives. The knives
are 10”-long and 0.060”-thick and made from premium steel so
they take and hold a sharp edge. The knives are retained with
tried and true wedge blocks and gib screws. A jackscrew is
located at each end of the knives to make setting critical heights
easier and more accurate. A knife setting gauge is also provided
to make setting the knives fast and easy.
This cutterhead is used for both jointing and planning operations.
The large diameter and mass of the all steel cutterhead body adds
considerable inertia that helps keep the JET 10" Jointer/Planer
cutting smoothly.
The JET 10" Jointer/Planer packs lots
of capability into a space and cost-
The motor powers the cutterhead and
feed rollers using tried and true belt
and chain drives.
saving package.
The twin knife system is
designed to be consistent
yet easy to adjust.
Jointing Table and Fence
The cast aluminum
jointing table is 36”long and 10-1/4”wide overall. The
table surface is
precisely machined
to be flat and
smooth. The JET
10" Jointer/Planer is
capable of a
maximum cut depth
of 1/8” with the cut adjusted using a single knob at the end of the infeed table. A handy
cut depth gauge is provided at the front edge of the infeed table. The infeed table is
locked in position with a pair of finger-operated knobs.
The extruded aluminum fence is 4-7/8”-tall and 25”-long. The fence can be used at 90degrees to the table surface for squaring stock or it can be tilted up to 45-degrees (right)
for bevel cuts. The fence is locked in place with an easy-to-use handle on the rear.
Planer Table
The planer table surface is 19-3/4”-long (with
the included extension table) by 10-1/2”-wide.
The table is raised and lowered with a hand
crank that plugs into the top of the JET 10"
Jointer/Planer. A handy scale next to the planer
infeed opening shows the current table to knife
distance and makes setup fast and easy. The
planer table moves up and down on four lead
screws, one in each corner of the main cabinet
for maximum stability. The table is secured for
making cuts with a single locking handle.
The JET 10" Jointer/Planer has a maximum planer thickness capacity of 4-1/2”, max cut
width of 10” and a maximum cut depth of 5/64”. The JET 10" Jointer/Planer will also
plane work pieces with a minimum length of 6”! For the best overall performance the
JET 10" Jointer/Planer has a fixed feed rate of 19.5 FPM. (feet per minute)
The infeed table adjustment (left) is operated by a single, easy to use knob. The fence
has a full 45-degree (out) adjustment (right) and locks with a repositionable lever on
the rear.
Despite its overall size, the JET 10” Jointer/Planer
has a very useful capacity range that will handle
the needs of even active home woodworking
shops.
Dust Collection
The JET 10" Jointer/Planer comes with a
single dust shroud assembly that can be
installed for either jointing or planer
functions. This chute is attached using fingeroperated knobs that make installation fast and
tool free. The dust shroud is also designed as
a safety interlock for the jointer-planer. This
means the machine will not operate unless the
dust shroud is installed in either the jointing
or planning mode.
We also include a hose adapter that allows
using either a 2-1/2” or 4”-diameter hose so
that the JET 10" Jointer/Planer is compatible
with your shop-vac or dust collection unit. The hose adapter also works in both jointing
and planer modes.
Stand
This all-steel stand is easy to assemble and very sturdy to
keep the JET 10" Jointer/Planer stable during use. Its design
helps to retain the small footprint to maximize shop floor
space.
If you have a small shop or workspace, the JET 10"
Jointer/Planer could be for you. Despite its space saving
footprint, the JET 10" Jointer/Planer includes many full-sized
machine features, accuracy and power. The user-friendly
features mean you will be up and running in no time.
The dust collection hood is used for both jointing
(here) and planing. It attaches using the same two
finger operated knobs in both modes. Note the hose
adapter that allows using standard 4”-diameter hose
or 2-1/2”-diameter shop-vac hoses.
The stand kit lets you use the
JET 10” Jointer/Planer as a
stand alone unit.
Loading...