This .pdf document is bookmarked
Operating Instructions and Parts Manual
6-inch Bench Top Jointer
Model JJ-6HHBT
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-718600
Ph.: 800-274-6848 Edition 1 06/2020
www.jettools.com Copyright © 2020 JET
1.0 IMPORTANT SAFETY INSTRUCTIONS
Warning – To reduce risk of injury:
1. Read and understand the entire owner’s manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with
all of these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This jointer is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a jointer, do not use until proper training and
knowledge have been obtained.
5. Do not use this jointer for other than its intended use. If used for other purposes, JET disclaims any
real or implied warranty and holds itself harmless from any injury that may result from that use.
6. Always wear approved safety glasses/face shields while using this jointer. Everyday eyeglasses only
have impact resistant lenses; they are not safety glasses.
7. Before operating this jointer, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips
are recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
10. Make certain the switch is in the OFF position before connecting the machine to the power supply.
11. Make certain the machine is properly grounded.
12. Make all machine adjustments or maintenance with the machine unplugged from the power source.
13. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting
wrenches are removed from the machine before turning it on.
14. Keep safety guards in place at all times when the machine is in use. If removed for maintenance
purposes, use extreme caution and replace the guards immediately.
15. Make sure the jointer is firmly secured to the stand or a bench before use.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged
should be carefully checked to determine that it will operate properly and perform its intended
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting
and any other conditions that may affect its operation. A guard or other part that is damaged should
be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Maintain a balanced stance at all times so that you do not fall or lean against the knives or other
moving parts. Do not overreach or use excessive force to perform any machine operation.
2
23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for
which it was not designed. The right tool will do the job better and safer.
24. Use recommended accessories; improper accessories may be hazardous.
25. Maintain tools with care. Keep knives sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
26. Turn off the machine and disconnect from power before cleaning. Use a brush or compressed air to
remove chips or debris — do not use bare hands.
27. Do not stand on the machine. Serious injury could occur if the machine tips over.
28. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
29. Before turning on machine, remove all extra equipment such as keys, wrenches, scrap, stock, and
cleaning rags away from the machine.
30. Always use a hold-down or push block when surfacing stock less than 12" inches long, or 3 inches
wide, or 3 inches thick.
31. Do not perform jointing operations on material shorter than 8", narrower than 3/4" or less than 1/4"
thick.
32. The hands must never be closer than 3 inches to
the cutterhead (see Figure).
33. Never apply pressure to stock directly over the
cutterhead. This may result in the stock tipping
into the cutterhead along with the operator's
fingers. Position hands away from extreme ends
of stock, and push through with a smooth, even
motion. Never back workpiece toward the infeed
table.
34. To avoid kickback, the grain must run in the
same direction you are cutting. Before attempting
to joint or plane, each work piece must be carefully examined for stock condition and grain
orientation.
35. When working with a swirl grain wood or burls, making it necessary to plane against the grain, use a
lesser depth of cut and a slow rate of feed.
36. Move the hands in an alternate motion from back to front as the work continues through the cut. Never
pass the hands directly over the cutter knife. As one hand approaches the knives remove it from the
stock in an arc motion and place it back on the stock in a position beyond the cutter knife.
37. At all times hold the stock firmly.
WARNING: This product can expose you to chemicals including lead and cadmium which are
known to the State of California to cause cancer and birth defects or other reproductive harm. For more
information go to http://www. p65warnings.ca.gov.
WARNING: Drilling, sawing, sanding or machining wood products generates wood dust and other
substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood
products or use a dust mask or other safeguards for personal protection.
Wood products emit chemicals known to the State of California to cause birth defects or other
reproductive harm. For more information go to http://www.p65warnings. ca.gov/wood.
- - SAVE THESE INSTRUCTIONS - -
3
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
2.0 About this manual
This manual is provided by JET covering the safe operation and maintenance procedures for the JET
Model JJ-6HHBT Jointer. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. This machine has been designed
and constructed to provide consistent, long-term operation if used in accordance with instructions set
forth in this manual. If there are any questions or comments, please contact either your local supplier or
JET. JET can also be reached at our web site: www.jettools.com.
Retain this manual for future reference. If the machine transfers ownership, the manual should
accompany it.
Read and understand the entire contents of this manual before attempting
assembly or operation. Failure to comply may cause serious injury.
Record your purchase information here for quick reference:
Stock no.:
Model no.:
Date of purchase:
Place of purchase:
4
3.0 Table of Contents
1.0 IMPORTANT SAFETY INSTRUCTIONS ............................................................................................... 2
2.0 About this manual .................................................................................................................................. 4
3.0 Table of Contents ................................................................................................................................... 5
4.0 Features................................................................................................................................................. 6
5.0 Specifications ......................................................................................................................................... 6
6.0 Shipping contents .................................................................................................................................... 7
7.0 Unpacking .............................................................................................................................................. 7
8.0 Assembly ................................................................................................................................................ 8
8.1 Attach support to planer ..................................................................................................................... 8
8.2 Install dust chute and filter bag ........................................................................................................... 8
8.3 Install fence and bracket to planer ..................................................................................................... 8
8.4 Mounting brackets .............................................................................................................................. 9
9.0 Operating controls .................................................................................................................................. 9
10.0 Adjustments ....................................................................................................................................... 10
10.1 Table positioning/depth of cut ........................................................................................................ 10
10.2 Fence positioning ........................................................................................................................... 10
10.3 Replacing/rotating knife inserts ...................................................................................................... 11
11.0 Basic Operation .................................................................................................................................. 11
11.1 Operating precautions .................................................................................................................... 11
11.2 Correct operating position .............................................................................................................. 11
11.3 Hand placement ............................................................................................................................. 12
11.4 Surfacing ........................................................................................................................................ 12
11.5 Direction of grain ............................................................................................................................ 12
11.6 Edge jointing ................................................................................................................................... 13
11.7 Beveling .......................................................................................................................................... 13
12.0 User-maintenance .............................................................................................................................. 14
12.1 Cutterhead care ............................................................................................................................. 14
12.2 Lubrication ..................................................................................................................................... 14
12.3 Belt replacement (drive/fan) ........................................................................................................... 14
13.0 Replacement Parts ............................................................................................................................. 15
13.1 JJ-6HHBT Jointer – Exploded View ............................................................................................... 16
13.2 JJ-6HHBT Jointer – Parts List ........................................................................................................ 17
14.0 Electrical Connection ......................................................................................................................... 20
15.0 Warranty and Service......................................................................................................................... 21
5
4.0 Features
Figure 4-1
5.0 Specifications
Table 1
Model number
Stock number 718600
Motor Brushed DC, 115V, 60Hz, 15A
On/off switch toggle switch with safety key
Recommended circuit size 1 15A
Sound emission 2 92 dB
Cutterhead speed 10,000 RPM
Cutterhead diameter 2 in. (50.8 mm)
Number of knives 14 inserts in 2 spiral rows
Cutter knife size (LxWxT) 0.59 x 0.59 x 0.10 in., R6/37° (HM15x15x2,5 mm R150/ 37°)
Dust port diameter 2-3/8 in. (fits 2-1/2 in. dust hose)
Jointer table 28-5/8 x 6-1/4 in. (727 x 159 mm)
Maximum stock removal 1/8 in. (3.175 mm)
Maximum cutting width 6 in. (152.4 mm)
Fence 22-3/4 x 4-3/8 in. (578 x 111 mm)
Fence tilt 45° L, 90°, 45° R
Fence positive stop 45° L, 90°, 45°R
Overall dimensions (LxWxH) 30 x 20 x 13 in. (762 x 508 x 330 mm)
Net weight 71 lbs. (32 kg)
Shipping weight 76 lbs. (34 kg)
1
subject to local/national electrical codes
2
The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace
conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks
involved only.
L = length, W = width, H = height, T = thickness
JJ-6HHBT
The specifications in this manual were current at time of publication, but because of our policy of
continuous improvement, Powermatic reserves the right to change specifications at any time and without
prior notice, without incurring obligations.
6
6.0 Shipping contents
Figure 6-1 – Contents of main carton
7.0 Unpacking
Remove all contents from the shipping carton.
Do not discard the carton or packing material
until your Model JJ-6HHBT Jointer is assembled
and is running satisfactorily.
Compare the contents of the carton against the
list of parts shown on these pages. The letter
identification in the list corresponds to the items
shown in the Figures. This is your key for
identifying the parts used throughout the
Assembly section for easy reference.
Remove the protective coating that is applied to
the table with a household grease-and-spot
remover.
Carton Contents
A ...... Planer with blade guard
B ...... Angle Fence
C ...... Fence tilting handle with spacer
D ...... Fence bracket assembly
E ...... Fence support
F ...... Spring
G ...... Fence sliding handle with spacer
H ...... Locking plate assembly
I ....... Filter bag
J… .... Dust chute
K ....... Push block
L… ... Push stick
......... (2) Star point screwdrivers (not shown)
......... Operator’s manual
......... Product registration card
Hardware bag includes:
2 Socket head bolts M6x20 (mount to fence)
2 Socket head bolts M6x16
2 Flat Washer 6mm
2 Lock Washer 6mm (mount to planer base)
3, 4, and 5mm Hex wrenches
4 Mounting brackets
Figure 7-1
7
8.0 Assembly
Slide the arm with the spring over the dust
exhaust port.
For assembly convenience, the item letter
designators used throughout the Assembly
section are the same as those used to identify
shipping content and hardware.
8.1 Attach support to planer
Attach fence support (E, Figure 8-1) to planer
with two M6x16 socket head bolts, flat washers
and lock washers.
Insert locking plate assembly (H) into support.
Position plate so that pins are against bottom
edge of support.
Secure plate in position with fence sliding handle
and spacer (G, Figure 8-1).
Close the zipper. See Figure 8-3.
Figure 8-3
8.3 Install fence and bracket to
planer
Attach fence (B, Figure 8-4) to fence bracket
assembly (D) with two M6x20 socket head bolts.
Slide fence and bracket over and onto dovetails
of support (E) and locking plate (H, Figure 8-1)
Figure 8-1
8.2 Install dust chute and filter bag
Slide the dust chute onto the end of the chip
exhaust. Tighten the pan head screw. See
Figure 8-2.
Figure 8-2
Open the zipper on the bottom of the bag, place
the spring inside of the filter bag arm.
Continue to slide fence forward so that the fence
is over the planer tables. At this position the
edge of the blade guard will rest against the
fence, and the entire width of the cutter head is
covered. Secure bracket in position with fence
sliding handle (G, Figure 8-1).
Insert fence tilting handle with spacer (C, Figure
8-4) through right link and thread into left link.
See Figure 8-5:
Make sure limit plate (A, Figure 8-5) is resting in
slot of block (B). Position fence against shaft (D)
and lock fence in position with fence tilting
handle.
Place a combination square against face of
fence and table surface. The fence and table
must be at 90° to each other. If not, loosen tilting
handle (C, Figure 8-4), loosen hex nut (C, Figure
8-5) and turn shaft (D, Figure 8-5) with a screw
driver until fence is square. Secure in position by
tightening hex nut (C, Figure 8-5).
Use a bevel gauge or protractor to check 45°
inward and outward limit stops. The 45° inward
stop (E, Figure 8-5) is the hex head bolt located
beneath the shaft. The 45° outward stop is
located at the top of the fence.
8
If adjustment is needed, loosen hex nut, turn hex
head bolt to proper position and secure in place
with hex nut.
Figure 8-4
Figure 8-6
9.0 Operating controls
Disconnect machine from
power source before making any
adjustments. Failure to comply may cause
serious injury.
Refer to Figure 9-1.
The operating positions of the On-Off switch are
located on the front of your jointer.
Figure 8-5
8.4 Mounting brackets
The jointer weighs approximately 72 lbs. when
completely assembled. The jointer must be
installed in a place with ample lighting and
correct power supply.
Make sure there is plenty of room for moving the
workpiece through the entire cut. There must be
enough room that neither operator nor
bystanders will have to stand in line with the
wood while using the tool.
Jointer can be installed on a workbench using
the provided mounting brackets (A, Figure 8-6).
Secure with bolts, lock washers and hex nuts
(not supplied).
Push the switch up to turn jointer on and push
down to turn the unit off.
The switch has a removable key that allows the
unit to be locked in the OFF position.
To activate locking mechanism:
Push the switch (A) to OFF position.
Pull switch key (B).
To deactivate locking mechanism:
Insert and press switch key in the slot on switch.
Figure 9-1
The jointer must be bolted to a firm, level
surface. Make sure the jointer does not rock and
the tables are level.
9
10.0 Adjustments
it outwards, turn the handle to the new
position, and release it.
10.1 Table positioning/depth of cut
The outfeed table (the left hand one when facing
the machine) is set to be level with the knives at
the highest point in their revolution.
The infeed and outfeed tables are preset at the
factory to be aligned with the cutterhead.
Rotate the knob beneath the infeed table (#2,
Figure 10-1) to raise or lower the infeed table for
desired depth of cut, according to the scale on
the front of the table.
3. Slide the fence to the desired position. The
fence can be positioned over the blade so
that only the desired width of the blade is
exposed. Make sure the exposed width
matches that of the workpiece.
4. Tighten the fence sliding handle so that the
fence is secure.
Figure 10-2
10.2.2 Bevel angles
The fence can be positioned to joint the wood at
any angle from 45° inward to 45° outward.
Figure 10-1
10.2 Fence positioning
10.2.1 Forward and back
1. Turn machine OFF.
2. Loosen the fence sliding handle (#1, Figure
10-2).
When “beveling” – cutting the entire edge of a
work piece to an angle – several passes may be
required due to the depth of cut needed.
“Chamfering” refers to removing only the corner
of the edge of the workpiece. Normally a
chamfer is made in one pass, so a 1/8 in. (3mm)
depth of cut is made.
1. Turn machine OFF.
2. Turn the fence tilt handle counterclockwise
to loosen it.
3. Manually tilt the fence to desired angle
inward or outward. If you have set up the
machine as described in sect. 8.0, the fence
will hit the stops inward or outward at 45°
and measurement should not be necessary
(Figure 10-2). However, it is advisable to
confirm the settings with a machinist square,
or similar angle gauge before commencing
Note: The handles are spring-loaded: if you
find it necessary to reposition a handle, pull
10
Figure 10-3
IMPORTANT: When removing or rotating
inserts, clean saw dust from the screw, the
insert, and the cutterhead platform. Dust
accumulation between these elements can
prevent the insert from seating properly, and
may affect the quality of the cut.
Before installing each screw, lightly coat the
screw threads with machine oil and wipe off any
excess.
Securely tighten each screw which holds the
knife inserts before operating the planer. Knife
inserts should be torqued to approximately 50 to
55 inch- pounds.
Make sure all knife insert
screws are tightened securely. Loose inserts
can be propelled at high speed from a
rotating cutterhead, causing injury.
10.3 Replacing/rotating knife inserts
Knife inserts are extremely
sharp. Use caution when cleaning or
changing. Failure to comply may cause
serious injury.
Disconnect jointer from power source/unplug.
The knife inserts on the model JJ-6HHBT are
four-sided. When dull, simply remove each
insert, rotate it 90° for a fresh edge, and re-install
it.
Use the provided star point screwdriver to
remove the knife insert screw. See Figure 10-4.
It is advisable to rotate all inserts at the same
time to maintain consistent cutting. However, if
one or more knife inserts develops a nick, rotate
only those inserts affected.
Each knife insert has etched numerals to keep
track of the rotations.
11.0 Basic Operation
Note: The Figures are general in nature and
may not show your particular jointer model.
11.1 Operating precautions
Always use sharp cutter knives.
The jointer fence must securely be locked
before machine use.
Check workpiece for foreign objects (nails,
screws) and for loose knots.
Feed with thicker workpiece end at the
front, hollow side downward.
Plane the stock with the grain, if possible.
Support long workpieces with roller stands
or an assistant.
Use push block(s) or push stick if possible
to keep hands away from cutting area.
11.2 Correct operating position
The operator must be positioned offset to the
infeed table, as shown in Figure 11-1.
Figure 10-4
11
Figure 11-1
11.3 Hand placement
Never pass hands directly
over the cutterhead.
At the start of the cut, the left hand holds the
workpiece firmly against the infeed table and
fence while the right hand pushes the workpiece
in a smooth, even motion toward the cutterhead.
After the cut is under way, the new surface rests
firmly on the outfeed table. The left hand is
transferred to the outfeed side and presses
down on this part of the workpiece, at the same
time maintaining flat contact of workpiece with
fence. The right hand presses the workpiece
forward, and before the right hand reaches the
cutterhead it should be moved to the work on the
outfeed table.
11.4 Surfacing
The purpose of surfacing (see Figure 11-2) on a
jointer is to produce one flat surface. The other
side can then be milled to precise, final
dimensions on a thickness planer resulting in a
board that is smooth and flat on both sides and
each side parallel to the other.
If the wood to be jointed is cupped or bowed,
place the concave side down, and take light
cuts until the surface is flat.
Never surface pieces shorter than 12 inches
or thinner than 3/8 inch without the use of a
special work holding fixture.
Never surface pieces thinner than 3 inches
without the use of a push block.
Cuts of approximately 1/16" or less at a time
are recommended, which provides for better
control over the material being surfaced.
More passes can then be made to reach the
desired depth.
11.5 Direction of grain
Avoid feeding work into the jointer against the
grain (Figure 11-3). This may result in chipped
and splintered edges.
It is strongly recommended that the provided
push block and push stick be used whenever
possible. See Figure 11-2. These are mandatory
when jointing smaller stock.
Figure 11-2
Figure 11-3
Feed with the grain to obtain a smooth surface,
as shown in Figure 11-4.
Figure 11-4
12
11.6 Edge jointing
Jointing (or edging) is the process of creating a
finished, flat edge surface that is suitable for
joinery or finishing (Figure 11-5). It is also a
necessary step prior to ripping stock to width on
a table saw.
Figure 11-5
Never edge a board that is less than 3 inches
wide, less than 1/4 inch thick, or 12 inches long,
without using a push block.
When edging wood wider than 3 inches lap the
fingers over the top of the wood, extending them
back over the fence such that they will act as a
stop for the hands in the event of a kickback.
2. Inspect stock for soundness and grain
direction.
3. Set the infeed table for a cut of
approximately 1/16.
4. If the board is bowed (curved), place the
concave edge down on the infeed table.
5. Feed the stock through the cutterhead,
making sure the face of the stock is
completely flat against the fence and the
edge is making solid contact on the infeed
and outfeed tables (Figure 11-6).
For wood wider than 3 inches – hold with
fingers close together near the top of the
stock, lapping over the board and extending
over the fence.
For wood less than 3 inches wide – use
beveled push blocks and apply pressure
toward the fence. Keep fingers near top of
push block.
6. Several passes may be required to achieve
full bevel.
When workpiece is twice the
length of the jointer infeed or outfeed table
use an infeed or outfeed support.
To edge a board:
1. Make sure the fence is set to 90°. Double
check it with a square.
2. Inspect stock for soundness and grain
direction. If the board is bowed (curved),
place the concave edge down on the infeed
table.
3. Set infeed table for a cut of approximately
1/16 inch.
4. Hold the stock firmly against the fence and
table, feed the stock slowly and evenly over
the cutterhead, as shown in Figure 11-5.
11.7 Beveling
Beveling an edge is the same operation as edge
jointing, except that the fence is tilted to a
specified angle.
Make certain material being beveled is over 12
inches long, more than 1/4 inch thick and 1 inch
wide.
Figure 11-6
To bevel:
1. Use a bevel gauge to determine the desired
angle. Then set the fence to the same angle.
13
12.0 User-maintenance
12.1 Cutterhead care
Blades are extremely sharp!
Use caution when cleaning or changing.
Failure to comply may cause serious injury!
The condition of the knife inserts will affect the
precision of the cut. Observe the quality of the
cut that the machine produces to check the
condition of the knives. Dull knives will tear,
rather than cut the wood fibers and produce a
fuzzy appearance.
When gum and pitch collect on the knife inserts,
carefully remove with a strong solvent. Failure to
remove gum and pitch build up may result in
excessive friction, blade wear and overheating.
When knife inserts become dull, rotate them.
After three rotations, replace them.
12.2 Lubrication
The cutterhead ball bearings are lifetime
lubricated and need no further care.
3. Remove the two screws that hold the belt
cover in place and remove cover situated at
the end of the cutter head.
4. Remove the four screws that hold the
bottom cover on and remove cover.
5. Remove the fan belt (B, Figure 12-1) from
the cutter head pulley first, then the drive
belt. Pull the belt towards you and turn the
belt at the same time until it rolls off the
pulleys.
6. Install new drive belt, then fan belt, by rolling
them onto the pulleys while turning the belts.
Make sure belts seat fully in groves of both
pulleys.
7. Reinstall covers.
12.3 Belt replacement (drive/fan)
1. Disconnect jointer from power source;
unplug.
2. Lay the jointer on its side so that the switch
is facing upward. See Figure 12-1.
Figure 12-1
14
Troubleshooting
Trouble Probable Cause Remedy
Low line voltage Correct low line voltage
Motor does not start.
Motor starts slowly or
fails to come to full
speed.
Motor running too hot
Snipe (gouging at end
of boards)
Defective switch Have switch replaced
Motor failure. Have motor repaired or replaced
Defective motor windings. Have motor repaired or replaced.
Take shallow depth of cut and attach
Clogged with wood chips
Motor overloaded Reduce load on motor
Restricted air circulation due to dust
accumulation
Dull knife inserts Rotate or replace inserts.
Inadequate support of long boards
Uneven feed Feed workpiece evenly and smoothly.
a shop-vac to exhaust port. Inspect
chip blower assembly and fan belt
Clean dust and restore normal air
circulation
Support long boards with roller stand
or an assistant.
13.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call
1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and
Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from
Powermatic. Some parts are shown for reference only, and may not be available individually.
15
13.1 JJ-6HHBT Jointer – Exploded View
16
13.2 JJ-6HHBT Jointer – Parts List
Index No. Part No. Description Size Qty
1 ............... TS-2311061 ............. Hex Nut ................................................................ M6 ............................... 1
2 ............... JJ6HHBT-002 .......... Block .................................................................... .................................... 1
3 ............... JJ6HHBT-003 .......... Shaft ..................................................................... .................................... 1
4 ............... JJ6HHBT-004 .......... Spring ................................................................... .................................... 1
5 ............... JJ6HHBT-005 .......... Limit Plate ............................................................ .................................... 1
6 ............... TS-1503111 ............. Socket Head Cap Screw ...................................... M6x50 ......................... 1
7 .................. JJ6HHBT-007 .......... Fence Bracket ...................................................... .................................... 1
8 .................. TS-2311061 ............. Hex Nut ................................................................ M6 .............................. 1
9 .................. JJ6HHBT-009 .......... Bracket Shaft........................................................ .................................... 1
10 ............. TS-1503051 ............. Socket Head Cap Screw ...................................... M6x20 ......................... 4
11 ................ JJ 6HH BT- 01 1 .......... Push Nut .............................................................. .................................... 2
12 ................ JJ 6HH BT- 01 2 .......... Right Link ............................................................. .................................... 1
13 ............. JJ6HHBT-013 .......... Spacer .................................................................. .................................... 1
14 ................ JJ 6HH BT- 01 4 .......... Fence Tilting Handle ............................................ .................................... 1
15 ................ JJ 6HH BT- 01 5 .......... Plate Shaft ............................................................ .................................... 1
16 ................ TS- 1481061 ............. Hex Cap Screw .................................................... M5x25 ......................... 1
17 ................ TS- 2331051 ............. Cap Nut ................................................................ M5 ............................... 1
18 ............. JJ6HHBT-018 .......... Fence ................................................................... .................................... 1
19 ................ JJ 6HH BT- 01 9 .......... Left Link ................................................................ .................................... 1
20 ................ TS- 1481061 ............. Hex Cap Screw .................................................... M5x25 ......................... 1
21 ............. TS-2331051 ............. Cap Nut ................................................................ M5 ............................... 1
22 ............. JJ6HHBT-022 .......... Fence Sliding Handle ........................................... .................................... 1
23 ............. JJ6HHBT-023 .......... Spacer .................................................................. .................................... 1
24 ................ TS- 1503041 ............. Socket Head Cap Screw ...................................... M6x16 ......................... 2
25 ............. TS-2361061 ............. Lock Washer ........................................................ 6 .................................. 2
26 ................ JJ 6HH BT- 02 6 .......... Fence Support ..................................................... .................................... 1
27 ............. JJ6HHBT-027 .......... Pin ........................................................................ .................................... 1
28 ............. JJ6HHBT-028 .......... Locking Plate ....................................................... .................................... 1
29 ............. JJ6HHBT-029 .......... Pin ........................................................................ .................................... 8
30 ............. JJ6HHBT-030 .......... Bracket ................................................................. .................................... 4
31 ................ JJ 6HH BT- 03 1 .......... Infeed Table ......................................................... .................................... 1
32 ................ TS- 1502021 ............. Socket Head Cap Screw...................................... M5x10 ......................... 8
33 ............. TS-2361051 ............. Lock Washer ........................................................ 5mm ............................ 8
34 ................ JJ 6HH BT- 03 4 .......... Connection Bracket .............................................. .................................... 4
35 ................ JJ 6HH BT- 03 5 .......... Table Support Plate ............................................. .................................... 1
36 ............. TS-1522011 ............. Socket Set Screw ................................................. M5x6 ........................... 4
37 ............. TS-2276081 ............. Socket Set Screw ................................................. M6x8 ........................... 4
38 ................ TS- 1523071 ............ Socket Set Screw ................................................. M6x25 ......................... 1
39 ............. TS-2311061 ............ Hex Nut ................................................................ M6 ............................... 1
40 ............. TS-1523081 ............ Socket Set Screw ................................................. M6x35 ......................... 1
41 ............. TS-2311061 ............ Hex Nut ................................................................ M6 ............................... 1
42 ............. JJ6HHBT-042 ......... Support Plate ....................................................... .................................... 1
43 ............. JJ6HHBT-043 ........ Lock Washer ........................................................ 5mm ............................ 2
44 ............. TS-1502021 ............ Socket Head Cap Screw ...................................... M5x10 ......................... 2
45 ............. JJ6HHBT-045 ......... Elevation Screw ................................................... ..................
46 ............. JJ6HHBT-046 ......... Handwheel ........................................................... .................................... 1
47 ............. JJ6HHBT-047 ......... Flat Washer .......................................................... 5mm ............................ 1
48 ............. TS-1533032 ............ Pan Head Machine Phillips Screw ....................... M5x10 ......................... 2
49 ............. JJ6HHBT-049 ......... Bearing Housing .................................................. .................................... 1
50 ............. BB-6201ZZ .............. Ball Bearing .......................................................... 6201-2Z ...................... 1
51 ............. JJ6HHBT-051 ......... Body With Outfeed Table ..................................... .................................... 1
52 ............. TS-1523051 ............ Socket Set Screw ................................................. M6x16 ......................... 4
53 ............. TS-1550041 ............ Flat Washer .......................................................... 6mm ............................ 6
.................. 1
17
Index No. Part No. Description Size Qty
54 ............. TS-2361061 ............ Lock Washer ........................................................ 6mm ............................ 4
55 ................. TS -1503071 ............. Socket Head Cap Screw ...................................... M6x30 ......................... 4
56 ............. JJ6HHBT-056 ......... Serrated Washer .................................................. 5mm ............................ 2
57 ............. TS-1550031 ............ Flat Washer .......................................................... 5mm ............................ 2
58 ............. TS-2361051 ............ Lock Washer ....................................................... 5mm ............................ 2
59 ............. TS-1533032 ............ Pan Head Machine Phillips Screw ....................... M5x10 ......................... 2
60 ............. JJ6HHBT-060 ......... Motor Brush.......................................................... .................................... 2
61 ............. JJ6HHBT-061 ......... Motor .................................................................... .................................... 1
62 ............. JJ6HHBT-062 ......... Motor Pulley ......................................................... .................................... 1
63 ............. TS-1550041 ............ Flat Washer .......................................................... 6mm ............................ 4
64 ............. TS-2361061 ............ Lock Washer ........................................................ 6mm ............................ 4
65 ............. TS-1503031 ............ Socket Head Cap Screw ...................................... M6x12 ......................... 4
66 ............. JJ6HHBT-066 ......... Motor Support ...................................................... .................................... 1
67 ............. TS-2361051 ............ Lock Washer ........................................................ 5mm ............................ 4
68 ............. TS-1503071 ............ Socket Head Cap Screw ...................................... M5x10 ......................... 4
69 ............. JJ6HHBT-069 ......... Cord Clamp .......................................................... .................................... 1
70 ............. .JJ6HHBT-070 ......... Spring ................................................................... .................................... 1
71 ............. JJ6HHBT-071 ......... Pin ........................................................................ .................................... 1
72 ............. TS-1533032 ............ Pan Head Machine Phillips Screw ....................... M5x10 ......................... 1
73 ............. JJ6HHBT-073 ......... Bumper ................................................................. .................................... 1
74 ............. JJ6HHBT-074 ......... Blade Guard ......................................................... .................................... 1
75 ............. JJ6HHBT-075 ......... Bushing ................................................................ .................................... 1
76 ............. JJ6HHBT-076 ......... Spring ................................................................... .................................... 1
77 ................ TS- 1550031 ............. Flat Washer .......................................................... 5mm ............................ 1
78 ................ TS- 1503071 ............. Socket Head Cap Screw ...................................... M5x10 ......................... 1
79 ................ JJ6 HH BT- 07 9 .......... Drive Belt ................................................................ 5PJ170 ....................... 1
80 ................ JJ 6HH BT- 08 0 .......... Cutterhead, Helical Body ..................................... .................................... 1
81 ................ JJ 6HH BT- 08 1 .......... Knife Insert Screw ................................................ .................................. 14
82 ................ 718601 ..................... Knife Inserts (sold in set of 5; includes #81 screws) ............................... 14
83 ................... BB -6201ZZ .............. Ball Bearing .......................................................... 6201-ZZ ...................... 1
84 ................ JJ6 HH BT- 08 4 .......... Bearing Housing .................................................. .................................... 1
85 ................ JJ 6HH BT- 08 5 .......... Star Point Screwdriver ......................................... .................................... 2
86 ................. TS -1504021 ............. Socket Head Cap Screw ...................................... M8x12 ......................... 4
8 7 ................... T S - 2276081 ............. Socket Set Screw ................................................. M6x8 ........................... 1
88 ................ JJ6 HH BT- 08 8 .......... Drive Pulley .......................................................... .................................... 1
89 ............. JJ6HHBT-089 .......... Cover .................................................................... .................................... 1
90 ................ TS- 1502011 ............. Socket Head Cap Screw ...................................... M5x8 ........................... 2
91 ............. JJ6HHBT-091 .......... Fan Belt ................................................................ 2PJ140 ........................ 1
92 ............. TS-1550031 ............. Flat Washer .......................................................... 5mm ..........
93 ............. TS-1533032 ............. Pan Head Machine Phillips Screw ....................... M5x10 ......................... 3
94 ............. JJ6HHBT-094 .......... Chip Collector....................................................... .................................... 1
95 .............JJ6HHBT-095 ........... Chip Exhaust ........................................................ .................................... 1
96 ............. JJ6HHBT-096 .......... Dust Chute ........................................................... .................................... 1
97 ................ TS- 2286252 ............. Pan Head Machine Phillips Screw ....................... M6x25 ......................... 1
98 ................ TS- 1502021 ............. Socket Head Cap Screw ...................................... M5x10 ......................... 1
99 ................ JJ6 HH BT- 09 9 .......... Flat Washer .................................................. Ø15xØ5x2 .................. 1
100 ........... JJ6HHBT-100 .......... Fan ....................................................................... .................................... 1
101 .............. JJ6 HHBT-1 01 .......... Mounting Plate ..................................................... .................................... 1
102 ............... TS- 1550041 ............. Flat Washer .......................................................... M6 ............................... 2
103 ........... TS-2361061 ............. Lock Washer ........................................................ M6 .............................. 2
104 ........... TS-1503031 ............. Socket Head Cap Screw ...................................... M6x12 ......................... 2
105 ........... JJ6HHBT-105 .......... Fan Shaft .............................................................. .................................... 1
106 ........... BB-6000ZZ ............... Ball Bearing .......................................................... 6000-ZZ ...................... 2
107 ........... JJ6HHBT-107 .......... Spacer .................................................................. .................................... 1
108 ........... TS-1523031 ............. Socket Set Screw ................................................. M6x10 ......................... 1
109 ........... JJ6HHBT-109 .......... Fan Pulley ............................................................ .................................... 1
.................. 3
18
Index No. Part No. Description Size Qty
110 ........... JJ6HHBT-110 .......... Self-Tapping Screw .............................................. ST4.2x9.5 ................... 6
111 ........... JJ6HHBT-111 .......... Base ..................................................................... .................................... 1
112 ........... JJ6HHBT-112 .......... Switch ................................................................... .................................... 1
113 ........... TS-1513011 ............ Socket Head Flat Screw ...................................... M5x10 ...................... 13
114 ........... JJ6HHBT-114 ......... Cover .................................................................... .................................... 1
115 ........... TS-1550021 ............ Flat Washer .......................................................... 4mm ............................ 6
116 ........... TS-1532032 ............ Pan Head Machine Phillips Screw ....................... M4x10 ........................ 6
117 ........... JJ6HHBT-117 ......... Foot B ................................................................... .................................... 2
118 ........... JJ6HHBT-118 ......... Foot A ................................................................... .................................... 2
119 ........... JJ6HHBT-119 ......... Strain Relief.......................................................... .................................... 1
120 ........... JJ6HHBT-120 ......... Power Cord .......................................................... ................................... 1
121 ........... JJ6HHBT-121 ......... Push Stick ............................................................ .................................... 1
122 ........... JJ6HHBT-122 ......... Push Block ........................................................... .................................... 1
123 ........... JJ6HHBT-123 ......... Spring ................................................................... .................................... 1
124 ........... JJ6HHBT-124 ......... Filter Bag .............................................................. .................................... 1
125 ........... JWBS10OS-25-1 .... Switch Safety Key ................................................ .................................... 1
126 ........... JJ6HHBT-126 ......... Pointer .................................................................. .................................... 1
127 ........... JJ6HHBT-127 ......... Depth Scale.......................................................... .................................... 1
128 ........... JJ6HHBT-128 ......... Rivet ..................................................................... .................................... 2
129 ........... JJ6HHBT-129 .......... Mounting Bracket (set of 4) .................................. .................................... 4
130 ........... TS-1550071 ............. Flat Washer .......................................................... 10mm .......................... 2
131 ........... JJ6HHBT-131 .......... Spring ................................................................... .................................... 1
132 ........... JJ6HHBT-132 .......... Model Label.......................................................... .................................... 1
133 ........... JJ6HHBT-133 .......... JET Warning Label .............................................. .................................... 1
134 ........... JJ6HHBT-134 .......... JET Logo Label ................................................... 4“x4“ ............................ 1
135 ........... JJ6HHBT-135 .......... ID Label ............................................................... .................................... 1
................. JJ6HHBT-136 .......... Motor Label (not Shown) ...................................... .................................... 1
301 ........... JJ6HHBT-301 .......... Block Assembly (#1 thru 3) .................................. .................................... 1
302 ........... JJ6HHBT-302 .......... Fence Bracket Assembly (#4 thru 12, #15, #19 thru 21) .......................... 1
303 ........... JJ6HHBT-303 .......... Locking Plate Assembly (#27, #28) ..................... .................................... 1
304 ........... JJ6HHBT-304 .......... Cutterhead Helical Assembly (#80 thru 85, #49, #50) ........... …………….1
305 ........... JJ6HHBT-305 .......... Mounting Plate Assembly (#105 thru 110) ........... .................................... 1
Note: Some parts may be listed for reference, but are only available as part of a larger assembly.
19
14.0 Electrical Connection
20
15.0 Warranty and Service
JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact
Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.
Warranty Period
The general warranty lasts for the time period specified in the literature included with your product or on the official JET
branded website.
JET products carry a limited warranty which varies in duration based upon the product. (See chart below)
Accessories carry a limited warranty of one year from the date of receipt.
Consumable items are defined as expendable parts or accessories expected to become inoperable within a
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.
Who is Covered
This warranty covers only the initial purchaser of the product from the date of delivery.
What is Covered
This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not
cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair,
alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood. Use of these machines
in the processing of metal, plastics, or other materials outside recommended guidelines may void the warranty. The
exceptions are acrylics and other natural items that are made specifically for wood turning.
Warranty Limitations
Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year
Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of
initial purchase when calling. If a product requires further inspection, the Technical Service representative will explain and
assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the
name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET
website.
More Information
JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit
the JET website.
How State Law Applies
This warranty gives you specific legal rights, subject to applicable state law.
Limitations on This Warranty
JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT.
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL,
CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as
general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to
parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET
products are not sold in Canada by JPW Industries, Inc.
Product Listing with Warranty Period
90 Days – Parts; Consumable items
1 Year – Motors; Machine Accessories
2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used for
industrial or commercial purposes; Air Tools
3 Year – selected bench top machinery
5 Year – Woodworking Machinery
Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools
NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or
any of its successors in interest to the JET brand.
®
branded
21
22
23
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.jettools.com
24
Loading...