Operating Instructions and Parts Manual
2-Ton Hydraulic Shop Crane
Model: JHC- 200X
WALTER M EIE R (Manufa c turin g) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-106200
Ph.: 800-274-6848 Revision B2 02/2012
www.waltermeier.com Copyright © 2012 Walter Meier (Manufacturing) Inc.
Warranty and Service
Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of
our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any
of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or
perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in
your area call 1-800-274-6848.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with
your local Walter Meier distributor, or visit waltermeier.com.
WARRANTY
JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW =
Woodworking).
WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools,
abrasives and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general JET warranty lasts for the time period specified in the product literature of each product.
WHAT IS NOT COVERED?
Five Year Warranties do not cover woodworking (WW) products used for commercial, industrial or educational
purposes. Woodworking products with Five Year Warranties that are used for commercial, industrial or education
purposes revert to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse,
abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name
of the location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the
merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price,
at our option. We will return the repaired product or replacement at our expense unless it is determined by us that
there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will,
at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be
responsible for the shipping and handling costs of the return.
HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE
LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR
FOR INCIDENTAL, CONTINGENT, SPECI AL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF
OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general
information and are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice,
those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason
whatsoever. JET® branded produc ts are not sold in Canada by Walter Meier.
2
Warnings
1. Study and understand all operating instructions before operating crane.
2. Do not exceed the rated capacity of the crane (position 1, 1/2 ton; position 2, 1 ton; position 3, 1-1/2 ton;
position 4, 2 ton. See Figure 1.
3. Assure that the load is not allowed to drop suddenly or swing during transporting.
4. Make sure that boom is fully lowered before adding oil to unit reservoir.
5. This shop crane is designed f or use only on hard, leve l surfaces capable of sustai ning the load. Use on
other than hard level surfaces can result in shop crane instability and possible loss of load.
6. Slowly lower boom and load to the lowest possible position before transporting load.
7. Assemble crane according to the owner’s manual. Make sure all bo lts and nuts are tight before placing
crane into operation.
8. Do not use crane for any other purpose than for which it was designed and intended.
9. Crane legs must always extend beyond the boom and each leg must be extended to the same length.
10. Do not extend any leg farther than red warning indicator line on each leg.
11. Boom extension hardware must be secure before attempting to lift any load.
12. Never place any part of the body under the load or crane while in use.
13. Never use the crane as the only means of support. Always move the load to a stable platform or work
surface before attempting any work.
14. Keep others away from the area while the crane is in operation.
15. Before attempting to raise load, make sure it is securely fastened and safety latches are secure.
16. Do not operate crane with twisted or kinked chain.
17. Do not remove labels from crane.
18. Never use crane for lifting people or loads over people.
19. Do not remove ram and use separately for any purpose.
20. Never operate the crane under the influence of medication, drugs or alcohol.
21. Fail ure to comply with all of these warnings may result in loss of load, damage to the shop crane, and/or
failure resulting in personal injury or property damage.
Familiarize yourself with the following safety notices used in this manual:
This means that if preca utions are not heeded, it m ay result in minor injury a nd/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
3
Specifications
Model Number ........................................................................................................................................ JHC-200X
Stock Number ............................................................................................................................................. 106200
Figure 1
The specifications in this manual are given as general information and are not binding. Walter Meier
(Manufacturing) Inc., reserves the right to effect, at any time and without prior notice, changes or alterations to
parts, fittings, and accessory equipment deemed necessary for any reason whatsoever.
Read and understand the entire contents of this ma nual before attempting assembly
or operation! Failure to comply may cause serious injury!
4
Assembly Instructions
Note: Refer to parts breakdown for part numbers
found in parenthesis (#):
1. Slide short extension legs (03) into the rear
support of base (01). Tighten bolt s to hold in
place.
2. Slide long extension legs (08) into front
supports of base (01). Tighten bolts to hold i n
place.
3. Connect post (10) to base (01) with two M12 x
25 hex cap bolts (09) and two M12 nuts (02).
4. Attach supports (11) to base (01) and top of
post (10) using three M12 x 100 hex cap bolt s
and three M12 nuts (15). Tighten firmly.
5. Connect boom (13) to post (10) using one M20
x 125 hex cap bolt (14) and one M20 nut (15).
6. Slide boom extension (16) into boom (13) and
fasten with one adjustment pin (26) and one
hitch pin (27).
7. Bolt lower portion of ram (21) to post (10)
using one M16 x 100 hex cap bolt (17) and
one M16 nut (18).
8. Bolt upper portion of ram (21) to boom (13)
using one M16 x 75 (22) hex cap bolt and one
M16 nut (18).
9. Insert small covers (28) into the short
extension legs (03), long extension legs (08),
and boom extension (16). Insert big cover (29)
into back end of boom (13).
Operation
1. Load to be lifted must be securely attached
with slings or chain of adequate size and
strength. Before lifting the load, be sure load
cannot twist, or fall from attachment.
2. Move crane into position. Legs must be
extended out beyond the boom extension.
3. Close hydraulic valve at base of ram by
inserting groove in handle into valve, and
turning clockwise until tight.
4. Place slings, or chains in center of hook and
make sure safety latch is s e curely latched.
5. Slowly raise load to desired height by inserting
handle into ram and pumping handle. Be
careful to note if the load wants to shift, and
keep load from rotating or swinging.
6. Move load to desired location by rolling cra ne
assembly. Use caution so that load does not
swing or rotate.
7. Carefully lower load to desired location by
inserting ram handle into valve at base of ram,
and slowly turning counter-clockwi se. Do not
lower too quickly, and confirm load is secure
once lowered fully.
Parts
Ordering Replacement Parts
To order parts or reach o ur service department, call 1-80 0-274-6848 Monday through Fr iday (see our w ebsite
for business hours, www.walteremeier.com). Having the Model Number and Serial Number of your machine
available when you call will allow us to serve you quickly and accurately.
5
Hydraulic Crane Assembly – Exploded View
6
Hydraulic Crane Assembly – Parts List
Index No. Part No. Description Size Qty
01 .............. JHC200X-01.............. Base......................................................................... ...................................... 1
02 .............. TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 6
03 .............. JHC200X-03.............. Extension Leg (short)............................................... ...................................... 2
04 .............. TS-1490031 .............. Hex Cap Bolt............................................................ M8×20 ......................... 16
05 .............. JHC200X-05.............. Caster Assembly...................................................... ...................................... 4
06 .............. TS-1551061 .............. Lock Washer ............................................................ M8 ............................... 16
07 .............. TS-1540061 .............. Hex Nut .................................................................... M8 ............................... 16
08 .............. JHC200X-08.............. Extension Leg (long) ................................................ ...................................... 2
09 .............. TS-1492011 .............. Hex Cap Bolt............................................................ M12×25 ......................... 2
10 .............. JHC200X-10.............. Post.......................................................................... ...................................... 1
11 .............. JHC200X-11.............. Support .................................................................... ...................................... 2
12 .............. TS-1492101 .............. Hex Cap Bolt............................................................ M12×100 ....................... 2
13 .............. JHC200X-13.............. Boom ....................................................................... ...................................... 1
14 .............. JHC200X-14.............. Hex Cap Bolt............................................................ M20 ×125 ....................... 1
15 .............. TS-1540121 .............. Hex Nut .................................................................... M20 ............................... 1
16 .............. JHC200X-16.............. Boom Extension....................................................... ...................................... 1
17 .............. JHC200X-17.............. Hex Cap Bolt............................................................ M16 ×100 ....................... 1
18 .............. TS-1540101 .............. Hex Nut .................................................................... M16 ............................... 3
19 .............. JHC200X-19.............. Load Hook w/chain .................................................. ...................................... 1
20 .............. TS-1499141 .............. Hex Cap Bolt............................................................ M12×80 ......................... 1
21 .............. JFHC200X-6 ............. Ram Assembly......................................................... ...................................... 1
22 .............. JHC200X-22.............. Hex Cap Bolt............................................................ M16 ×75 ......................... 1
23 .............. JHC200X-23.............. Handle ..................................................................... ...................................... 1
24 .............. JHC200X-24.............. Steering Handle ....................................................... ...................................... 2
25 .............. JHC200X-25.............. Washer .................................................................... ...................................... 2
26 .............. JHC200X-26.............. Adjustment Pin......................................................... ...................................... 1
27 .............. JHC200X-27.............. Hitch Pin .................................................................. ...................................... 1
28 .............. JHC200X-28.............. Small Cover ............................................................. ...................................... 5
29 .............. JHC200X-29.............. Big Cover ................................................................. ...................................... 1
.................. JHC200X-RK............. Ram Repair Kit (not shown)..................................... ...................................... 1
.................. JHC200X-ID .............. I.D. Label (not shown).............................................. ...................................... 1
.................. JHC200X-WL ............ Warni ng Label (not shown) ...................................... ...................................... 1
.................. JHC200X-CL ............. Capacity Labels (set of 4: 1/2T,1T,1.5T,2T)(not shown) ................................ 1
7
Hydraulic Ram – Exploded View
8
Hydraulic Ram – Parts List
Index No. Part No. Description Size Qty
.................. JFHC200X-6 ............. Hydraulic Ram Assembly......................................... ...................................... 1
30 .............. JFHC200X-30 ........... Valve Body............................................................... ...................................... 1
31 .............. JFHC200X-31 ........... Copper Washer * ..................................................... M46 ............................... 1
32 .............. JFHC200X-32 ........... Cylinder.................................................................... ...................................... 1
33 .............. JFHC200X-33 ........... O-ring * .................................................................... M40x5.5 ........................ 1
34 .............. JFHC200X-34 ........... O-ring Retainer * ...................................................... M31.3x3.55 ................... 1
35 .............. JFHC200X-35 ........... Ram ......................................................................... ...................................... 1
36 .............. JFHC200X-36 ........... Top Nut .................................................................... M48 ............................... 1
37 .............. JFHC200X-37 ........... O-ring * .................................................................... M33.5x3.55 ................... 1
38 .............. JFHC200X-38 ........... Gasket * ................................................................... M70x1 ........................... 1
39 .............. JFHC200X-39 ........... Oil Chamber............................................................. ...................................... 1
40 .............. JFHC200X-40 ........... Oil Plug * .................................................................. M15x9.5 ........................ 1
41 .............. JFHC200X-41 ........... Seal Ring * ............................................................... M81x4 ........................... 1
42 .............. JFHC200X-42 ........... Tube......................................................................... ...................................... 1
43 .............. SB-6MM .................... Steel Ball.................................................................. M6 ................................. 1
44 .............. JFHC200X-44 ........... Seal Ring * ............................................................... M88x6 ........................... 1
45 .............. JFHC200X-45 ........... Release Valve.......................................................... ...................................... 1
46 .............. SB-6MM .................... Steel Ball.................................................................. M6 ................................. 2
47 .............. JFHC200X-47 ........... Copper Washer * ..................................................... M18 ............................... 2
48 .............. JFHC200X-48 ........... Pump Cylinder ......................................................... ...................................... 2
49 .............. JFHC200X-49 ........... O-ring * .................................................................... M66x3 ........................... 2
50 .............. JFHC200X-50 ........... Back-up Ring * ......................................................... M12x 7 ........................... 2
51 .............. JFHC200X-51 ........... Plunger
.................. JFHC200X-51A ......... Plunger
52 .............. JFHC200X-52 ........... Link Pin .................................................................... ...................................... 1
53 .............. JFHC200X-53 ........... Handle Socket ......................................................... ...................................... 1
54 .............. JFHC200X-54 ........... Connecting Pin ........................................................ ...................................... 3
55 .............. JFHC200X-55 ........... Cotter Pin ................................................................. ...................................... 3
56 .............. JFHC200X-56 ........... Pin............................................................................ M2x 30 ........................... 1
57 .............. JFHC200X-57 ........... Bolt........................................................................... M14x4 5 ......................... 1
.................. JFHC200X-RK .......... Ram Repair Kit (includes items with asterisk *) ....... ........................................
(s/n 12020001 and higher)
(previous to s/n 12020001)
........................... ...................................... 2
........................... ...................................... 1
9
10
11
WALTER M EIE R (Ma nufa cturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.waltermeier.com
12
Loading...