JET J-2500, J-2530, J-2550 Operating Instructions and Parts Manual

This .pdf document is bookmarked
Operating Instructions and Parts Manual
Drill Press
Models: J-2500, J-2530, J-2550
J-2530 J-2500 J-2550
WALTER MEIER (Manuf acturing), Inc.
427 New Sanford Road
Ph.: 800-274-6848 Revision B 04/2012 www.waltermeier.com Copyright © 2012 Walter Meier (Manufacturing), Inc.

W arranty and Service

YEAR
DAY
WARRANTY
90
WARRANTY
1
YEAR
WARRANTY
5
LIFETIME
WARRANTY
LIFE
YEAR
WARRANTY
2
YEAR
WARRANTY
3
Walter Meier (Man ufacturing), Inc., warran ts every produc t it se lls. If one of our tools need s ser vice or repair, one of our Authorized Service Centers located throughout the United States c an give you quick ser vice. In most cases, any of these W alter Meier Authorized S ervice Centers can a uthorize warranty repair, assist you in obtaini ng parts, or perfor m routine mai ntenance and major repair on your JET® tools. For the n ame of an Authoriz ed Ser vice Center in your area call 1-800-274-684 8.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For c omplete, up-to-date product information, check with your local Walter Meier distributor, or visit walter meier.co m.
WARRANTY
JET products carry a limi ted warranty which varies in dur ation based upon th e product. ( MW = Metalworki ng, W W = Woodworki ng)
Beam Clamps Chain Hoist­ Manual Lever Hoists
WARRANTY
Pullers-JCH Models Scissor Lift Tables Screw Jacks Trolleys-Geared Trolleys-Plain Winches-Manual WW Air Filtration WW Bandsaws WW Buffers
WARRANTY
YEAR
WW Drill Presses WW Dust Collectors WW Dust Filters WW Dust Fittings WW Jointers WW Lathes WW Planers WW Sanders
WW Shapers WW Tablesaws
LIFE
LIFETIME
Fastening Tools Mechanics Hand Tools Striking Tools Vises (no -precision) Clamps
WARRANTY
90
DAY
Lathe Accessories Machine Accessories Mobile Bases Safety Equipment Specialty Items Vise Accessories
WARRANTY
YEAR
Air Tools­ Contractor Air Tools-Industrial Air Tools-Light Industrial Lubrication
Body Repair Kits Bottle Jacks Cable Pullers Cold Saws
WARRANTY
Hoists-Air Hoists-Electric Metal forming Mill/Drills Milling Machines MW Bandsaws MW Drill Presses MW Finishing Equipment MW Lathes MW Precision Vises
WARRANTY
YEAR
Palet Trucks Rigging Equip. Service Jacks Stackers Surface Grinders Tapping Trolleys-Air Trolleys-Electric Web Slings Winches-Electric
YEAR
WW Benchtop Tools
Warranty reverts to 1 Year Warranty if woodworking (WW) products listed above are used for industrial or educational purposes.
WHAT IS COV ERED?
This warranty covers any defects in work manship or materia ls subject to the exceptions stated below. Cutting tools, abrasives a nd other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warran ty covers only the ini tia l purchaser of the pro duct.
WHAT IS THE PERIOD O F COVERAGE?
The general JET warranty lasts for the ti me period spec ified in the produc t literature of each pro duct.
WHAT IS NOT COVERED?
Five Year Warranties do not cover wood working (WW) products use d for commercial, industrial or educational purpos es. Woodworking products with Five Y ear W arranties that are use d for commercial, ind ustrial or education purposes revert to a One Year Warranty. This warranty doe s not cover defec ts due direc tly or indirectly to misuse, abuse, n egligence or accidents, nor mal wear-and­tear, improper repair or alterations, or lack of maintenance.
HOW TO G ET SERVICE
The product or part must be returned for examinatio n, postage pr epaid, to a location designated by us. For the name of the locati on nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and a n explanation of the c omplai nt must accompany the merchandi se. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price, at our option.
We will return the repaired product or replace ment at our expense unless it is de termined by us that there is no d efect, or that the defect resu lted from causes not within the scope of our warranty in which case we will, at your direction, dispose of or return the produc t. In the event you choose to have th e product r eturned, y ou will be responsi ble for the shipping an d hand ling costs of the return.
HOW STATE LAW APPLIES
This warran ty gives you specific legal rights; y ou may also have other rights whic h vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MA NUFACTURI NG), I NC., LIMITS ALL IMPLIED WARRANTIES TO THE PE RIOD OF THE LI MITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED W ARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDE NTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSI ON OR LIMITATION OF INCIDENTAL OR CONSEQUE NTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSI ON MAY NOT APPLY TO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are gi ven as ge neral infor matio n and are not binding. Members of Walter Meier reser ve the right to effect a t any time, without prior notice, those alterations to parts, fittings, and accessory equip ment which they may deem necessary for any reaso n wha tsoever. J ET® branded products are not sold in Canada by Walter Meier.
2

Table of Contents

Warranty and Service......................................................................................................................................2
Table of Contents ...........................................................................................................................................3
Warnings........................................................................................................................................................4
Introduction ....................................................................................................................................................6
Specifications .................................................................................................................................................6
Shipping Contents ..........................................................................................................................................7
Required Tools ...............................................................................................................................................7
Assemb ly .......................................................................................................................................................8
Before Assembly .........................................................................................................................................8
Column Assembly .......................................................................................................................................8
Table Bracket ..............................................................................................................................................8
Crank Handle and Table Lock Handle...........................................................................................................8
Column Lock Handle ...................................................................................................................................9
Table Installation .........................................................................................................................................9
Head Assembly ...........................................................................................................................................9
Chuck and Arbor Installation ........................................................................................................................9
Chuck and Arbor Removal ......................................................................................................................... 10
Adjustment ................................................................................................................................................... 10
Depth Stop Adjustment .............................................................................................................................. 10
Changing Spindle Speeds .......................................................................................................................... 11
Return Spring Adjustment .......................................................................................................................... 11
Work Light (J-2500 and J-2530 only) .......................................................................................................... 11
Table Tilt Adjustment ................................................................................................................................. 12
Operation ..................................................................................................................................................... 12
Installing Drills ........................................................................................................................................... 12
Positioning the Workpiece .......................................................................................................................... 12
Using the Vise ........................................................................................................................................... 12
Basic Operation......................................................................................................................................... 12
Maintenance ................................................................................................................................................ 12
Lubrication ................................................................................................................................................... 12
Electrical ...................................................................................................................................................... 13
Grounding Instructions ............................................................................................................................... 13
115 Volt Operation .................................................................................................................................... 13
230 Volt Operation .................................................................................................................................... 13
Extension Cords ........................................................................................................................................ 13
Troubleshooting ............................................................................................................................................ 14
Replacement Parts .................................................................................................................................... 15
Parts List – J-2500, J-2530 ........................................................................................................................ 15
Exploded View – J-2500, J-2530 ................................................................................................................ 18
Parts List – J-2550 .................................................................................................................................... 19
Exploded View – J-2550 ............................................................................................................................ 22
Wiring Diagram............................................................................................................................................. 23
J-2500/J-2530 – 115V ............................................................................................................................... 23
J-2500/J-2530 – 230V ............................................................................................................................... 23
J-2550 ...................................................................................................................................................... 24
The specifications in this manual are given as general information and are not binding. Walter Meier (Manufacturing), Inc., reserves the right to effect, at any time and without prior notice, changes or alterations to parts, fittings, and accessory equipment deemed necessary for any reason whatsoever.
3

Warnings

1. Read and understand the entire owners manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of
these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This drill press is designed and intended for use by properly trained and experienced personnel only. If you
are not familiar with the proper and safe operation of a drill press, do not use until proper training and knowledge have been obtained.
5. Do not use this drill press for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing), Inc., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
6. Always wear approved safety glasses/face shields while using this drill press. Everyday eyeglasses only have
impact resistant lenses; they are not safety glasses.
7. Before operating this drill press, remove tie, rings, watches and other jewelry, and roll sleeves up past the
elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other co nstruction activities co ntain
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of expos ure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are
removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes,
use extreme caution and replace the guards immediately.
16. Make sure the drill press is firmly sec ured to the floor or bench before use.
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work area. Keep children away.
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.
4
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless
acts that can result in serious injury.
23. Maintain a balanced stance at all times so that you do not fall or lean against the spindle or ot her moving
parts. Do not overreach or use excessive force to perform any machine operation.
24. Us e the right tool at the correct speed and feed rate. Do not for ce a tool or attachment to do a job for which it
was not designed. The right tool will do the job better and safer.
25. Use recommended accessories; improper accessories may be hazardous.
26. Maintain tools with care. Keep drill bits sharp and clean for the best and safest performance. Follow
instructions for lubricating and changing accessories.
27. Make sure the work piece is securely attached or clamped to the table. Never use your hand to hold t he work
piece.
28. Turn off the machine before cleaning. Use a brush or compressed air to remove c hips or debris — do not use
your hands.
29. Do not stand on the machine. Serious injury could occur if the machine tips over.
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes
to a complete stop.
31. Remove loose items and unnecessary work pieces from the area before starting the machine.
Familiarize yours elf with the f ollow ing saf et y not ices used in t his manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
- - SAVE THESE I NSTRUCTI ONS - -
5
Introduction
The JET 15-Inch 16-Speed Drill Presses and 20-Inch 12-Speed Drill Presses, Models J-2500, J-2530 and J-2550, feature rugged cast iron design with ground-steel columns for drilling accuracy in metal, wood, and plastic. The head casting features a ball bearing spindle assembly, supported by four permanently-lubricated, heavy duty ball bearings that are mounted in an enclosed quill for extended life.

Specifications

Model
J-2500 J-2530 J-2550
Stock Number ................................................ 354400 .............................. 354401 ...............................354402
Model Type .................................................... 15-Inch Floor ..................... 15-Inch Bench....................20-Inch Floor
Drilling Capacity
Cast Iron.................................................... Up to 5/8 In. ....................... Up to 5/8 In. .......................Up to 3/4 In.
Steel .......................................................... Up to 1/2 In. ....................... Up to 1/2 In. .......................Up to 5/8 In.
Drill to Center ................................................. 15 Inches ........................... 15 Inches ...........................20 Inches
Motor
Rating ........................................................ 3/4 hp, 1-Phase ................. 3/4 hp, 1-Phase .................1 hp, 1-Phase
RPM .......................................................... 1725 .................................. 1725 ...................................1725
Voltage............................................115/230V (prewired 115V).......115/230V (prewired 115V) ......115/230V (prewired 115V)
Column Diameter ........................................... 2-7/8 In. ............................. 2-7/8 In...............................3-5/8 In.
Quill
Diameter.................................................... 1-7/8 In. ............................. 1-7/8 In...............................2-1/4 In.
Travel ........................................................ 3-1/8 In. ............................. 3-1/8 In...............................4-3/4 In.
Table
Overall ....................................................... 11-1/2 x 11-1/2 In. ............. 11-1/2 x 11-1/2 In...............18-1/2 x 16-1/2 In.
Working Surface........................................ 9-1/2 x 9-1/2 In. ................. 9-1/2 x 9-1/2 In...................15-1/2 x 13-1/2
Travel ........................................................ 24 In. ................................. 15-1/2 In.............................21-1/2 In.
Base
Size ........................................................... 11 x 19-1/2 In. ................... 10-1/2 x 18 In. ....................22-3/4 x 17-3/4 In.
Working Surface........................................ 7 x 7-1/2 ........................... 8 x 8 ...................................13 x 14-1/2
Chuck Size ..................................................... 5/8-In., Key Chuck ............. 5/8-In., Key Chuck .............5/8-In, Key Chuck
Overall Dimensions
Length ....................................................... 31 In. ................................. 31 In. ..................................33-1/2 In.
Width ......................................................... 13 In. ................................. 13 In. ..................................18-1/2 In.
Height ........................................................ 63 In. ................................. 39-1/2 In.............................67 In.
Spindle to Table (Max.) .................................. 24 In. ................................. 15-1/2 In.............................24 In.
Spindle to Column (Max.) ............................. 7-1/2 In. ............................. 7-1/2 In...............................10-1/2 In.
Spindle
To Base ..................................................... 48 ...................................... 24 .......................................43-1/2
Taper ......................................................... MT-2 .................................. MT-2 ..................................MT-3
Number of speeds .................................... 16 ....................................... 16 .......................................12
RPM ......................................................... 200, 290, 350, 430 ............. 200, 290, 350, 430 .............150, 260, 300,
500, 580, 640, 720 500, 580, 640, 720 440, 490, 540, 800, 870, 1440, 1630 800, 870, 1440, 1630 1150, 1550, 1840, 1820, 2380, 2540, 3630 1820, 2380, 2540, 3630 2220, 2950, 4200
Shipping Weight ............................................. 185 pounds........................ 157 pounds ........................321 pounds
6

Shippi ng Cont ents

Unpack the carton and verify that all parts listed below are included.
Main Parts
1 ea Head Assembly 1 ea Table 1 set Column and Table Bracket Assembly 1 ea Base
Additiona l Part s
1. 1 set Chuck and Chuck Key
2. 1 pc Arbor
3. 1 pc Drift Key
4. 1 pc Table Crank Handle
5. 1 pc Table Lock Handle
6. 1 pc Column Lock Handle
7. 3 pcs Downfeed Handles and Knobs
8. 4 pcs M10 x 40 Hex Cap Screws
9. 1 set Hex Wrenches (3mm, 5mm, 6mm)
Other Material
1 ea Owner’s Manual 1 ea Warranty Registration Card
Required Tools
1. 17mm Box Wrench or a 6” – 8” Adjustable Wrench
2. 15/16" wrench
Additional Parts
7

Assembly

Read and understand all assembly instructions before attempting assembly! Failure to comply may cause serious injury!

Before Assembly

1. Remove the contents from the shipping container.
2. Compare the contents of the shipping container with the list found above. Report any shortages or damage to your JET distributor.
3. Clean all rust protected surfaces with kerosene or a light solvent. Do not use lacquer thinner, paint thinner, or gasoline. These will damage plastic components and painted surfaces.

Col u mn Assembly

Referring to Figure 1:
1. Place the base (A) on a level floor.
2. Install the table bracket (A) together with the rack (B) as shown in Figure 2.
Figure 2
3. Slide the rack ring (D) over the column (C), placing it so it rests against the rack (B) as
shown in Figure 3 and tighten firmly.
2. Place the colum n assembly (B) on the base (A)
and align the holes in the column support with the holes in the base.
3. Note: The column shown in Figure 1 is for the
JDP-15MF. While the JDP-15M column is slightly different in appearance, the assembly procedure is the same.
4. Using a 17mm wrench, secure the column (B) with four M10 x 40 hex cap screws (C) to the
base.
Figure 1
Figure 3

Crank Han dle and Table Lo ck Handle

Referring to Figure 4 (shown already assembled):
1. Loosen the setscrew (B) on the table crank handle (A).
2. Slide the handle (A) onto the table bracket shaft.
3. Turn the handle until the setscrew is opposite the flat section on the shaft, and tighten the setscrew to secure the handle.
4. Inst all the table lock handle (C), but do not tighten.

Tab le Bracket

When shipped, the rack ring and rack are bundled
together with the column in plastic wrap.
Referring to Figures 2 and 3:
1. Remove the wrap and take the rack ring (D) and
rack (B) off the column (C).
Figure 4
8

Col u mn Lock Hand le

Referring to Figure 5:
Thread the column lock handle (D) into the table
bracket (E).
Figure 5

Table Installation

Referring to Figure 6:
1. Place the table (A) on the bracket (B).
2. Tighten the table lock handle (C).
2. Rotate head assembly unt il sides of the pulley cover are parallel with the sides of the base.
3. Tighten two setscrews (A) with a 5mm hex
wrench (provided) until they are snug.
Figure 7
4. Install three downfeed handles (B) into the
downfeed hub (C).

Chuck and Arbor Installation

Referring to Figure 8:
1. Twist the chuck (B) to retract the chuck jaws if
they are exposed.
2. Install the chuck (B) to the arbor (A) tightly.
3. Insert the chuck and arbor assembly into the
spindle (C). Pull the downfeed handle down to
press the arbor in place.
Note: Put a piece of scr ap wood (D) on the table to protect the chuck nose when pulling the downfeed
handle (E) down to press into place.
Figure 6

Head Ass embly

Referring to Figure 7:
1. With the aid of a second person, carefully lift the
head onto the column top and slide it down into
position
The head assembly is heavy! Use care when lifting onto the col um n!
Figure 8
9

Chuck and Arbor Removal

Referring to Figure 9:
1. Unplug machine from the power source.
2. Raise the table until it is about seven inches below the chuck.
3. Place a piece of scrap wood on the table, and
lower quill (A) using the downfeed handle.
4. Rotate spindle to align the keyhole in the spindle with the keyhole in the quill.
5. Insert the drift key (B) into the aligned slots and
tap lightly. The chuck and arbor assembly should fall from the spindle.

Adjustment

Depth Stop Adjustment

Referring to Figure 10:
To drill multiple holes at the same preset depth, use the depth stop:
1. Use a pencil to mark the depth the bit will drill into the workpiece.
2. With the drill bit in the chuck, lower downfeed
handle to advance bit to your mark (A).
3. With yo ur other hand, advance the lock nuts (B)
on the depth stop rod until they are snug to the
seat (C).
4. The drill bit will now advance to this point.
5. To release, advance the nuts counter-clockwise to the top of the depth stop.
Figure 9
Figure 10
10

Changing Spindle Speeds

A spindle speed and pulley/belt arrangement chart
for all models is found on the inside of the pulley cover (D, Fig. 11). Refer to this chart whenever
changing speeds.
Note: The chart in Figure 12 is for models J-2500
and J-2530 only.
To change spindle speeds:
1. Unplug the machine from the power source.
2. Loosen two bar knobs (E, Fig. 11) found on
each side of the head assembly.
3. Rotate the tension adjuster (F, Fig. 11)
clockwise to bring the motor base as close to the head as possible.
4. For desired speed, change the location of belts per pulley/belt arrangement chart.
5. Rotate the tension adjuster (F. Fig. 11)
counterclockwise to tension the belts.
6. Tighten two bar knobs (E, Fig. 11). Belts are
properly tensioned when finger and thumb pressure midway between the two pulleys causes approximately ½” deflection.
Figure 11
Figure 12 – Spi ndle Speed Chart for J-2500, J- 2530

Return Spring Adju st ment

The return spring is adjusted at the factory and should not need further adjustment. If adjustment is deemed necessary, follow the steps below while referring to Figure 13:
1. Unplug the machine from the power source.
2. Loosen two hex nuts (A). Do not remove.
3. Firmly hold the coil spring cover (B).
4. Pull out the cover and rotate until the pin (C) on
the return spring plate engages the next notch in the coil spring cover. Turn the cover clockwise to decrease tension and counter-clockwise to increase tension.
5. Tighten two hex nuts (A). Do not over-t ighten. Nuts
should not contact the housing when tight. The hex nuts should be tightened against each other.
Figure 13

Wo rk Light ( J- 2500 and J-2530 only)

Install a light bulb, no larger than 60 watts into the socket accessed from beneath the head. The rocker
switch controls the light switch (D, Fig. 13).
11

Table Tilt Adjustment

The table tilt adjustments are made on the table bracket under the table.
To tilt the table (refer to Figures 14 and 15):
In the following steps do not over loosen. This could result in the table assembly to separate from the column, f all and cause injury.
1. Loosen the socket head set screw (A) with a
3mm hex w rench.
2. Using a 15/16" wrench, loosen the hex cap screw (B), and tilt the table to the desired angle by aligning the arrow (C, Fig. 15) on the rotating
part of the bracket to the desired angle (in
degrees) displayed on the scale (D, Fig 15) at
the base of the bracket.
3. Tighten the hex cap s cr ew (B).
4. Tighten the sock et head se t scr ew (A).

Positioni ng the Workpiece

Always place a piece of wood (or plywood) on the table. This will prevent "splintering" or making heavy burrs on the underside of the workpiece as the drill breaks through. The wood should contact the left side of the column.

Using the Vise

For the small workpiece that cannot be clamped to the table, use a drill press vise. The vise must be clamped or bolted to the table. Always use a back­up piece of scrap wood to cover the table. This protects both the table and the drill bit.

Basic Operatio n

Place material to be drilled in such as way as to come into contact with the left side of the column. This prevents the material from spinning.
If the work piece is not large enough to come into contact w ith t he col um n, use a clamp or drill press vise that is securely fastened to the table! Failure to comply may cause ser ious injury!

Oper ation

Figure 14
Figure 15
Feed the bit into the material with only enough force to allow the drill bit t o wor k. Feeding too slowly may cause burning of the workpiece. Feeding too quickly may cause t he motor t o stop and/or t he drill bit to break.
Generally speaking, the smaller the drill bit, the greater the RPM required. Wood requires higher speeds than metal. Metal is usually drilled at slower speeds.
In dusty environments, frequently blow out any dust that accumulates inside the motor.

Maintenance

Before any intervention on the machine, disconnect it from the electrical supply by pulling out the plug or switching off the main switch! Failure to comply may cause serious injury.
A coat of automobile-type wax applied to the table and column will help to keep the surfaces clean.
If the power cord is worn, cut, or damaged in any way, have it replaced immediately.

Installing Drills

Insert the drill into the chuck jaws about 1" (25.4mm) long. When using a small drill do not insert it so far that the jaws touch the flutes of the drill. Make sure that the drill is centered in the c huck before tightening the chuck with the key.

Lubrication

All of the ball bearings are packed with grease at the factory. They require no further lubrication.
Periodically lubricate the gear, rack, table elevation mechanism, the splines (grooves) in the spindle, and the teeth of the quill with a #2 tube grease.
12

Electrical

Grounding Instructions
This tool must be grounded while in use to protect the operator f rom electric shoc k.
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor, with insulation having an outer surface that is green with or without yellow stripes, is the equipment­grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug.
230 Volt Operation
Referring to Figure 17:
If 230V, single-phase operation is desired, the following instructio ns must be followed:
Disconnect the machine from the power source.
The JET drill press motor has four numbered leads that are f actory connected for 115V operation, as s hown in (A). For 230V operation reconnect the leads as shown in (B).
The 115V attachment plug (C), supplied with the drill press, must be replaced with a UL/CSA listed plug suitable for 230V operation (D). Contact your local Authorized JET Service Center or qualified electrician for proper procedures to install the plug. The drill press must comply with all local and national codes after the 230-volt plug is installed.
The drill press with a 230-volt plug should o nly be connected to an outlet having the same configuration as shown in (D). No adapter is available nor should be used with the 230-volt plug.
Repair or replace a damaged or worn cord immediately.
115 Volt Operation
Referring to Figure 16:
As received from the factory, your drill press is ready to run at 115-volt operation. This drill press, when wired for 115 volt, is intended for use on a circuit that has an outlet and a plug that looks like the one illustrated in (A). A temporary adapter, which looks like the adapter sho wn in (B), may be used to connect this plug to a two-pole receptacle if a properly grounded outlet is not available. The temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. This adapter is not applicable in Canada. The green colored rigid ear, lug, or tab, extending from the adapter, must be connected to a permanent ground such as a properly grounded outlet box.
Figure 16
Figure 17
Extension Cords
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your machine will draw. An undersized cord will cause a drop in the line voltage resulting in power loss and overheating. The table following shows the correct size to use depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. Remember, the smaller the gauge number, the heavier the cord.
Length of Cord AWG
000 – 25 Feet 16 025 – 50 Feet 14
The drill press with a 230-volt plug should only be connected to an o utlet having the same configuration (D, Fig. 17). No adapter is available or should be used with the 230-volt plug.
Important: In all cases (115 or 230 volts), make certain the receptacle in question is properly grounded. If you are not sure, have a registered electrician check the receptacle.
13

Troubleshooting

Trouble Probable Cause Remedy
Drill press unplugged from wall, or motor. Check all plug connections.
Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker.
Drill press will not start.
Cord damaged. Replace cord.
Starting capacitor bad. Replace starting capacitor.
Drill press does not come up to speed.
Drill Press vibrates excessively.
Noisy Operation.
Workpiece Burns.
Drill bit wanders.
Extension cord too light or too long. Replace with adequate size and length cord.
Low current. Contact a qualified electrician.
Stand on uneven surface. Adjust stand so that it rests evenly on the floor.
Bad belt(s). Replace belts.
Incorrect belt tension.
Dry spindle.
Loose spindle pulley.
Loose motor pulley. Tighten setscrews in pulleys.
Incorrect Speed.
Chips not clearing from hole or bit. Retract drill bit frequently to remove chips.
Dull drill bit. Resharpen, or replace drill bit.
Feeding too slowly. Increase feed rate.
Bit sharpened incorrectly. Resharpen bit correctly.
Bent drill bit. Replace drill bit.
Adjust belt tension. See the Changing Spindle Speeds section.
Lubricate spindle. See the Lubrication section.
Check tightness of retaining nut on pulley, and tighten if necessary.
Change to appropriate speed; see the Changing Spindle Speeds section.
Wood splinters on the underside.
Drill bit binds in workpiece.
Excessive drill bit runout, or wobble.
Quill returns too slow, or too fast.
Chuck or arbor does not stay in place.
Bit, or chuck not installed properly. Reinstall the chuck, or bit properly.
No backing board used.
Workpiece pinching the bit. Support or clamp workpiece.
Excessive feed rate. Decrease feed rate.
Chuck jaws not tight. Tighten chuck jaws.
Improper belt tension.
Bent drill bit. Replace drill bit.
Worn spindle bearings. Replace spindle bearings.
Bit, or chuck not properly installed. Reinstall the bit, or chuck properly.
Spring has improper tension.
Dirt, grease, etc on arbor, chuck, or spindle.
Place a scrap board underneath the workpiece to prevent splintering.
Adjust belt tension (Changing Spindle Speeds )
Adjust spring tension. See the Return Spring Adjustment section.
Clean all mating surfaces thoroughly with a cleaner degreaser.
14

Parts

Repl acement Part s
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

Parts L ist – J-2500, J-2530

Index No. Part No. Description Size Qty
1A............ 10600110 ................Base for J-2530 / JDP-15M ................................................................. 1
1B............ 10800101 ................Base for J-2500 / JDP-15MF (not shown) ............................................. 1
2A............ JDP15-1002A ..........Column Holder for J-2530 / JDP-15M ................................................... 1
2B............ 10600204 ................Column Holder for J-2500 / JDP-15MF ................................................. 1
3 .............. TS-2279121 ............Hex Socket Set Screw ......................................M10-12 ...................... 3
4A............ JDP15-1004A ..........Body Column for J-2530 / JDP-15M ..................................................... 1
4B............ JDP15-1004B ..........Body Column for J-2500 / JDP-15MF ................................................... 1
................ 10600404A1 ............Column Assy for J-2530 / JDP-15M (includes #2A and #4A) .................. 1
................ 10400401A1 ............Column Assy for J-2500 / JDP-15MF (includes #2B, #3 and #4B) .......... 1
5 .............. TS-2229403 ............Hex Head Bolt ..................................................M10x40 ...................... 4
6 .............. 10600604 ................Table Bracket ..................................................................................... 1
................ JDP15-1006 ............Table Bracket Assy (includes #6 thru #18) ............................................ 1
7 .............. 10600702 ................Gear .................................................................................................. 1
8 .............. 10600802 ................Gear Shaft ......................................................................................... 1
9 .............. 10600902 ................Worm ................................................................................................. 1
10A.......... 10601009A1 ............Crank Handle Assy ............................................................................. 1
12 ............ JDP15-1012 ............Table Bracket ..................................................................................... 1
13 ............ TS-0071011 ............Hex Head Bolt ..................................................5/8-11 x 1-1/2 ............. 1
14 ............ TS-2276101 ............Hex Socket Set Screw ......................................M6-10 ........................ 1
16 ............ 10601601 ................Tilting Scale ....................................................................................... 1
17 ............ JDP15-1017 ............Centering Scale .................................................................................. 1
18 ............ JDP15-1018 ............Drive Screw......................................................Φ 2.3-5 ...................... 2
19 ............ 10601901 ................Column Lock Handle.........................................M12 x 1.75-35 ........... 1
20 ............ 10602001 ................Table Lock Handle ............................................M10 x 1.5 .................. 1
21 ............ J-5625221 ...............Table ................................................................................................. 1
22A.......... 10602204 ................Rack for J-2530 / JDP-15M ................................................................. 1
22B.......... 10602205 ................Rack for J-2500 / JDP-15MF ............................................................... 1
23 ............ 10602304 ................Rack Ring ........................................................Φ 73.5........................ 1
24 ............ TS-2276081 ............Hex Socket Set Screw ......................................M6-8 .......................... 1
25 ............ JDP15-1025 ............Head.................................................................................................. 1
26 ............ TS-2279121 ............Hex Socket Set Screw ......................................M10-12 ...................... 2
27 ............ JDP15-1027 ............Lamp Socket ...................................................................................... 1
28 ............ TS-1534042 ............Cr. Re. Pan Head Screw ...................................M6-12 ........................ 2
29 ............ 10602901 ................Handle Shifter .................................................................................... 1
30 ............ 10603002 ................Motor Bar Shifter ................................................................................ 1
31 ............ TS-2228161 ............Hex Head Bolt ..................................................M8-16 ........................ 1
32 ............ 10603206 ................Motor Rod .......................................................................................... 1
33 ............ 10603301 ................Shifter Bolt .......................................................M10-33 ...................... 2
34 ............ 10603416 ................Motor Base.......................................................75 x 125mm ............... 1
35 ............ 2502NBC412 ...........Spring Washer..................................................Φ1/2" ......................... 1
36 ............ TS-1540081 ............Hex Nut............................................................M12 ........................... 2
37 ............ 10603704 ................Hub ................................................................................................... 1
38 ............ 10603807 ................Feed Shaft ......................................................................................... 1
................ JDP15-1038 ............Feed Shaft Assy (includes #37 thru #39) .............................................. 1
39 ............ TS-209402 ..............Roll Pin ............................................................M5-16 ........................ 1
43A.......... JDP15-1043 ............Handle Bar ......................................................................................... 1
15
Parts L ist – J-2500, J-2530
Index No. Part No. Description Size Qty
45 ............ 10604505 ................Scale Ring ......................................................................................... 1
50A.......... JDP15-1050 ............Spring Cap ......................................................................................... 1
51 ............ 10605115 ................Shaft Seat .......................................................................................... 1
53 ............ TS-0561052 ............Hex Nut............................................................1/2"-20 ....................... 1
54 ............ 10605403 ................Quill Set Screw .................................................M10-28 ...................... 1
55 ............ TS-1540071 ............Hex Nut............................................................M10 ........................... 1
56 ............ 10605608 ................Quill .................................................................MT2 ........................... 1
................ JDP15-1056 ............Quill and Spindle Assy (includes #56 thru # 64) .................................... 1
57 ............ 10605702 ................Rubber Washer .................................................................................. 1
58 ............ 10605822 ................Spindle ............................................................MT2 ........................... 1
59 ............ 2001ZZ6204 ............Ball Bearing........................................................................................ 1
61 ............ 2001ZZ6203 ............Ball Bearing........................................................................................ 1
62 ............ TS-2360161 ............Washer ............................................................M16 ........................... 1
63 ............ 10606301 ................Nut Lock ............................................................................................ 1
64 ............ 10606401 ................Spindle Nut ........................................................................................ 1
65 ............ 10606505 ................Driving Sleeve .................................................................................... 1
................ JDP15-1065 ............Driving Sleeve Assy (includes #65 thru #67) ......................................... 1
66 ............ 2001ZZ6204 ............Ball Bearing........................................................................................ 2
67 ............ 10606703 ................Rack ring..........................................................Φ 45 T=4.................... 1
68 ............ 10606801 ................Retaining Ring .................................................................................... 2
69 ............ 10606904 ................Pulley Set Nut .................................................................................... 1
70 ............ JDP15-1070 ............Spindle Pulley .................................................................................... 1
71 ............ 21015M2J30 ...........Drilling Arbor ....................................................MT2*JT3 .................... 1
72A.......... JDP15-1072 ............Chuck Assy ........................................................................................ 1
73 ............ 10607303 ................Wedge Shifter .................................................................................... 1
74 ............ JDP15-1074 ............Motor ................................................................................................. 1
................ JDP15-1074A ..........Centrifugal Switch (not shown) ............................................................ 1
................ JDP15-1074B ..........Start Capacitor (not shown) ...............................200MFD 125VAC ....... 1
75 ............ JDP15-1075 ............Motor Wire ......................................................................................... 1
76 ............ TS-2208201 ............Hex. Hd. Screw ................................................M8-20 ........................ 4
77 ............ TS-1550061 ............Flat Washer......................................................M8 ............................. 8
78 ............ TS-1540061 ............Hex Nut............................................................M8 ............................. 4
79 ............ JDP15-1079 ............Motor Pulley ....................................................................................... 1
80 ............ 2571MNC307 ..........Parallel Key ......................................................5 x 5-20...................... 1
81 ............ TS-1504021 ............Hex Socket Set Screw ......................................M8-12 ........................ 1
83 ............ JDP15-1083 ............Strain Relief ....................................................................................... 1
84 ............ TS-1534042 ............Cr. Re. Pan Head Screw ...................................M6-12 ........................ 1
85 ............ JDP15-1085 ............Power Cable ...................................................................................... 1
87 ............ JDP15-1087 ............Rocker Switch .................................................................................... 1
88 ............ JDP15-1088 ............Switch Box ......................................................................................... 1
89 ............ TS-1533042 ............Cr. Re. Pan Head Screw ...................................M5-12 ........................ 3
90A.......... JDP15-1090 ............Pulley Cover Assy............................................................................... 1
................ JDP15-1090A ..........U Shaped Protecting Rubber (not shown)............................................. 1
92 ............ JDP15-1092 ............Cr. Re. Round Washer Hd. Screw......................M6 x 1.0-12 ................ 4
95 ............ JDP15-1095 ............Center Pulley...................................................................................... 1
................ JDP15-1095A ..........Center Pulley Assy (includes #95 thru #98) .......................................... 1
96 ............ JDP15-1096 ............Ball Bearing........................................................................................ 2
98 ............ 10609801 ................Center Pulley Shaft ............................................................................. 1
99 ............ VB-A28 ...................V-Belt...............................................................A-28........................... 1
101 .......... TS-0680021 ............Flat Washer......................................................1/4" ............................ 4
106 .......... TS-0561052 ............Hex Nut............................................................½”-20 ......................... 1
109 .......... JDP15-1109 ............Clamp-Cord ........................................................................................ 3
110 .......... 2668BBDA23...........Cr. Re. Pan Head Screw ..................................M5-8 .......................... 3
112 .......... 10611201 ................Chuck Key Holder ............................................................................... 1
113 .......... TS-2286122 ............Cr. Re. Round Washer Hd. Screw......................M6-12 ........................ 1
119 .......... VB-A26 ...................V-Belt...............................................................A-26........................... 1
16
Parts L ist – J-2500, J-2530
Index No. Part No. Description Size Qty
128 .......... TS-2285162 ............Cr. Re. Truss Hd. Tapping Screw ......................M5-16 ....................... 2
137 .......... JDP15-1137 ............Switch Cover ...................................................................................... 1
138 .......... TS-1533042 ............Cr. Re. Pan Head Screw ...................................M5-12 ....................... 2
139 .......... JDP15-1139 ............Rocker Switch .................................................................................... 1
140 .......... 10614001 ................Motor Rod .......................................................................................... 1
149 .......... 2536MBE616...........Roll Pin ............................................................6-25 ........................... 2
162 .......... 10916202 ................Warning Label .................................................................................... 1
166 .......... JDP15-1166 ............Speed Diagram .................................................................................. 1
169 .......... JDP15-1169 ............Trade-Mark Label ............................................................................... 1
170 .......... 2658MZDU36 ..........Drive Screw......................................................Φ 2.3-5 ...................... 6
601 .......... TS-2245082 ............Cr. Re. Pan Head Screw ...................................M5-8 .......................... 4
602 .......... TS-0733031 ............External Tooth Lock Washer..............................No 10 ......................... 2
610 .......... TS-1534692 ............Cr. Re. Pan Head Screw ...................................M6-35 ....................... 2
611 .......... JDP15-1611 ............Cr. Re. Pan Head Screw ..................................................................... 1
612 .......... TS-1540071 ............Hex Nut............................................................M10 ........................... 1
613 .......... 10661301 ................Set Bolt .............................................................................................. 1
................ JDP15-1613 ............Set Bolt Assy (includes #613, 848, 849) ............................................... 1
614 .......... 13005701 ................Nut………………………………………….M16........................................ 2
615 .......... 13005601 ................Washer ............................................................Φ24 ........................... 1
616 .......... TS-1502081 ............Hex. Soc. Hd. Cap Blot .....................................M5-35 ....................... 1
617 .......... JDP15-1617 ............Set Ring ............................................................................................. 1
618 .......... 10661801 ................Circular Nut ........................................................................................ 1
634 .......... 2502ABC410 ...........Spring Washer..................................................Φ10 ........................... 1
700 .......... TS-152704 ..............Wrench Hex ....................................................................................... 1
701 .......... TS-152706 ..............Wrench Hex ....................................................................................... 1
702 .......... TS-152707 ..............Wrench Hex ....................................................................................... 1
801 .......... JDP15-1801 ............Lead Wire Assembly ........................................................................... 1
848 .......... JDP15-1848 ............Drive Screw......................................................Φ 2.3-5 ...................... 2
849 .......... JDP15-1849 ............Scale ................................................................................................. 1
922 .......... 2801ABRF04 ...........Strain Relief .....................................................Φ 20 .......................... 2
999 .......... TS-1540081 ............Hex Nut............................................................M12x10 ...................... 3
1000 ........ 100633Y8................Plastic Sleeve................................................. ................................... 1
1001 ........ 10810401A1 ............Chuck Guard Assembly................................... ................................... 1
17

Exploded View – J-2500, J-2530

18

Parts L ist – J-2550

Index No. Part No. Description Size Qty
1 .............. J-5627751 ...............Base .................................................................................................. 1
2 .............. J-5627761 ...............Collar, Column.................................................................................... 1
3 .............. 5626231 ..................Set Screw ........................................................M10 x 40 mm ............. 1
4 .............. 5627771 ..................Column .............................................................................................. 1
5 .............. 5627781 ..................Screw, Hex Head..............................................M12 x 40 mm ............. 4
6 .............. J-5627791 ...............Bracket, Table .................................................................................... 1
7 .............. 5625071 ..................Gear, Pinion ....................................................................................... 1
8 .............. 5625081 ..................Shaft, Gear......................................................................................... 1
9 .............. 5625091 ..................Worm ................................................................................................. 1
10 ............ 5627811 ..................Handle, Lowering/Raising.................................................................... 1
11 ............ 5626251 ..................Screw, Hex Head..............................................M6 x 12 mm ............... 1
13 ............ 5627821 ..................Screw, Hex Head..............................................5/8” x 2” ..................... 1
14 ............ 5627831 ..................Pin, Location ...................................................................................... 1
15 ............ 5627841 ..................Nut, Hex...........................................................1/4" x 20” ................... 1
16 ............ 5627851 ..................Scale, Tilting....................................................................................... 1
17 ............ 5625181 ..................Scale, Angle ....................................................................................... 1
18 ............ 5625191 ..................Set Screw ........................................................Ø2.3x 5 mm ............... 3
19 ............ 5625211 ..................Handle, Lock ....................................................M12 x 180 mm............ 1
21 ............ J-5627861 ...............Table ...............................................................18-3/4” x 16-3/4” ......... 1
22 ............ 5627871 ..................Rack .................................................................................................. 1
23 ............ J-5627881 ...............Retainer, Rack.................................................................................... 1
24 ............ 5627061 ..................Screw Set, Hex Socket .....................................M6 x 10mm ................ 1
25 ............ J-5627891 ...............Head.................................................................................................. 1
26 ............ 5627021 ..................Screw Set, Hex Socket .....................................M10 x 12mm .............. 2
28 ............ 5627911 ..................Screw, Pan Head, Cr.-Re. .................................M6 x 12mm ................ 2
29 ............ 5627121 ..................Lever, Tension Adjustment .................................................................. 1
30 ............ 5627131 ..................Cam................................................................................................... 1
31 ............ 5627141 ..................Screw, Hex Head..............................................M8 x 16 mm ............... 1
32 ............ 5627921 ..................Shaft, Motor Base ............................................................................... 1
33 ............ 5627931 ..................Lock, Motor Bar .................................................................................. 2
34 ............ J-5627941 ...............Base, Motor........................................................................................ 1
35 ............ 5627181 ..................Washer, Spring.................................................Ø1/2” ......................... 2
36 ............ 5627191 ..................Nut, Hex...........................................................M12 ........................... 2
37 ............ 5627211 ..................Hub ................................................................................................... 1
38 ............ 5627951 ..................Shaft, Feed Pinion .............................................................................. 1
38A.......... 5627961 ..................Shaft Assembly, Feed Pinion ............................................................... 1
39 ............ 5627971 ..................Pin, Roll ............................................................................................. 1
40 ............ 5627241 ..................Pin, Scale Set..................................................................................... 1
41 ............ 5627981 ..................Wedge, Scale Locking ........................................................................ 1
42 ............ 5627991 ..................Screw, Depth Lock............................................M8 x 17 mm ............... 1
43 ............ 5629011 ..................Handle ............................................................................................... 3
43A.......... 5629021 ..................Bar Assembly, Handle......................................................................... 3
44 ............ 5627271 ..................Grip ................................................................................................... 3
45 ............ 5629031 ..................Housing, Spindle Depth....................................................................... 1
46 ............ 5629041 ..................Scale ................................................................................................. 1
47 ............ 5625481 ..................Pointer ............................................................................................... 1
48 ............ 5626551 ..................Screw, Drive ....................................................................................... 3
49 ............ 5629051 ..................Coil .................................................................................................... 1
50 ............ 5629061 ..................Housing, Spring .................................................................................. 1
50A.......... 5629071 ..................Housing Assembly, Spring .................................................................. 1
51 ............ 5629081 ..................Seat, Spring ....................................................................................... 1
53 ............ 5629091 ..................Nut, Hex...........................................................1/2"-20 ....................... 2
54 ............ 5627321 ..................Screw, Set, Quill ...............................................M10 x 27mm .............. 1
55 ............ 5627331 ..................Nut, Hex...........................................................M10 ........................... 1
56 ............ 5629111 ..................Quill ................................................................................................... 1
56A.......... 5629121 ..................Quill Assembly (includes #56 thru 64) .................................................. 1
19
Parts L ist – J-2550
Index No. Part No. Description Size Qty
57 ............ 5629131 ..................Washer, Rubber ................................................................................. 1
58 ............ 5629141 ..................Spindle ............................................................MT3, Ø34 ................... 1
59 ............ 5629151 ..................Bearing, Ball .....................................................6206ZZ ...................... 1
60 ............ 5629161 ..................Bearing, Ball, Thrust .........................................2906 ............................
61 ............ 5635271 ..................Bearing, Ball .....................................................6204Z ........................ 1
62 ............ 5629171 ..................Washer .............................................................................................. 1
63 ............ 5629181 ..................Lock, Washer ..................................................................................... 1
64 ............ 5629191 ..................Lock, Nut............................................................................................ 1
65 ............ 5629211 ..................Lock, Driving ...................................................................................... 1
66 ............ 5629221 ..................Bearing, Ball .....................................................6206Z ........................ 2
67 ............ 5629231 ..................Collar ................................................................................................. 1
68 ............ 5629241 ..................Ring, Retaining ................................................................................... 2
69 ............ 5629251 ..................Nut, Pulley Lock ................................................................................. 1
70 ............ 5629261 ..................Pulley, Spindle.................................................................................... 1
71 ............ 5624641 ..................Arbor ...............................................................MT3 x JT3 .................. 1
72 ............ 5628931 ..................Chuck ..............................................................RJ3 - 16L .................. 1
72A.......... 5627401 ..................Chuck and Key ................................................................................... 1
73 ............ 5624671 ..................Wedge, Taper .................................................................................... 1
74 ............ J-5629271 ...............Motor ................................................................................................. 1
76 ............ 5629291 ..................Screw, Hex Head..............................................M8 x 25 mm ............... 4
77 ............ 5627511 ..................Washer, Flat ....................................................5/16” .......................... 4
78 ............ 5625821 ..................Nut, Hex...........................................................M8 ............................. 4
79 ............ 5629311 ..................Pulley, Motor ...................................................................................... 1
80 ............ 5629321 ..................Key .................................................................................................... 1
81 ............ 5629331 ..................Screw, Set .......................................................M8 x 8 mm ................. 1
83 ............ 5627551 ..................Cla mp ................................................................................................ 2
84 ............ 5626841 ..................Screw, Pan Head..............................................M5 x 8 mm ................. 2
85 ............ 5629341 ..................Cord, Power ....................................................................................... 1
87 ............ JDP15-1087 ............Push-Button Switch ............................................................................ 1
88 ............ 5629361 ..................Cover, Switch ..................................................................................... 1
89 ............ 5626871 ..................Screw, Pan Head..............................................M5 x 12 mm ............... 2
92 ............ 5627591 ..................Washer, Round Head Screw .............................M6 x 12 mm ............... 4
93 ............ 5629381 ..................Screw, Truss Head Tapping ..............................M4 x 12 mm ............... 1
94 ............ 5627611 ..................Knob .................................................................................................. 1
95 ............ 5629391 ..................Pulley, Center..................................................................................... 1
96 ............ 5621681 ..................Bearing, Ball .....................................................6202Z ........................ 2
98 ............ 5629411 ..................Shaft, Pulley ....................................................................................... 1
99 ............ 5624701 ..................V-Belt...............................................................A-30........................... 1
101 .......... 5627641 ..................Washer, Flat .....................................................1/4" ............................ 4
119 .......... 5637541 ..................V-Belt...............................................................A-32........................... 1
128 .......... TS-2285162 ............Screw, Machine ................................................M5 x 16 mm ............... 2
129 .......... 5629421 ..................Screw, Socket Head Cap ..................................M8 x 30 mm ............... 2
130 .......... 5629431 ..................Screw, Socket Head Cap ..................................M8 x 25 mm ............... 1
131 .......... 5629441 ..................Key, Chuck......................................................................................... 1
140 .......... 5629451 ..................Shaft, Motor Base ............................................................................... 1
149 .......... 5629461 ..................Pin, Roll ............................................................................................. 2
601 .......... 5629471 ..................Screw, Pan Head..............................................M4 x 12 mm ............... 1
602 .......... 5629481 ..................Washer, External Tooth Lock.............................Ø4 ............................. 2
605 .......... 5629491 ..................Pin, Roll ............................................................................................. 1
606 .......... 5629511 ..................Pin, Roll ...........................................................Ø2.5 x 10 mm............. 1
610 .......... 5513738 ..................Screw ................................................................................................ 2
611 .......... 5513739 ..................Block, Depth Stop ............................................................................... 1
612 .......... 5513740 ..................Nut .................................................................................................... 1
613 .......... 5513741 ..................Rod, Depth Stop Adjustment .............................2550 Only .................. 1
614 .......... 5513742 ..................Nut, Adjustment Lock .......................................................................... 1
615 .......... 5513743 ..................Washer .............................................................................................. 1
20
Parts L ist – J-2550
Index No. Part No. Description Size Qty
616 .......... 5513744 ..................Screw, Clamping ................................................................................ 1
617 .......... J-5518233 ...............Clamp, Depth Stop support ................................................................. 1
618 .......... 5513746 ..................Nut .................................................................................................... 1
700 .......... 5627711 ..................Wrench, Allen ...................................................3 mm ......................... 1
701 .......... 5629521 ..................Wrench, Allen ...................................................5 mm ......................... 1
903 .......... 5627721 ..................Grommet ............................................................................................ 2
904 .......... J-5629371 ...............Cover Assembly, Pulley ...................................................................... 1
905 .......... 10810402A1 ............Chuck Guard Assembly....................................................................... 1
906 .......... 11361702 ................Set Ring ............................................................................................. 1
21

Exploded View – J-2550

22

Wiri ng Diagram

J-250 0/ J- 2530 – 115V

J-250 0/ J- 2530 – 230V

23

J-255 0 – 115V

J-255 0 – 230V

24
Loading...