JET DC-1200VX-BK1, DC-1200VX-CK1, DC-1200VX-BK3, DC-1200VX-CK3 Operating Instructions and Parts Manual

Operating Instructions and Parts Manual
DC-12 00V X S eries Dust Co llectors
Now with
DC-1200VX with Bag Fil ter Ki t DC-1200VX with Canister Kit
WALTER MEIER (Manuf acturing), Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M- 710701
Ph.: 800-274-6848 Revision A 03/2011 www.waltermeier.com Copyright © 2011 Walter Meier (Manufacturing), Inc.
W arranty and Service
Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine
®
maintenance and major repair on your JET 1-800-274-6848.
MORE INFORMATION
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit waltermeier.com.
WARRANTY
JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW = Woodworking).
WHAT IS COVERED?
This warranty covers any defects in workmanship or materials subject to the exceptions stated below. Cutting tools, abrasives and other consumables are excluded from warranty coverage.
WHO IS COVERED?
This warranty covers only the initial purchaser of the product.
WHAT IS THE PERIOD OF COVERAGE?
The general JET warranty lasts for the time period specified in the product literature of each product.
WHAT IS NOT COVERED?
Five Year Warranties do not cover woodworking (WW) products used for commercial, industrial or educational purposes. Woodworking products with Five Year Warranties that are used for commercial, industrial or education purposes revert to a One Year Warranty. This warranty does not cover defects due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair or alterations, or lack of maintenance.
HOW TO GET SERVICE
The product or part must be returned for examination, postage prepaid, to a location designated by us. For the name of the location nearest you, please call 1-800-274-6848.
You must provide proof of initial purchase date and an explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we will repair or replace the product, or refund the purchase price, at our option. We will return the repaired product or replacement at our expense unless it is determined by us that there is no defect, or that the defect resulted from causes not within the scope of our warranty in which case we will, at your direction, dispose of or return the product. In the event you choose to have the product returned, you will be responsible for the shipping and handling costs of the return.
HOW STATE LAW APPLIES
This warranty gives you specific legal rights; you may also have other rights which vary from state to state.
LIMITATIONS ON THIS WARRANTY
WALTER MEIER (MANUFACTURING) INC., LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
WALTER MEIER SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Walter Meier sells through distributors only. The specifications in Walter Meier catalogs are given as general information and are not binding. Members of Walter Meier reserve the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET products are not sold in Canada by Walter Meier.
tools. For the name of an Authorized Service Center in your area call
®
branded
2
Table of Contents
Warranty and Service .................................................................................................................................2
Table of Contents ......................................................................................................................................3
Warnings ...................................................................................................................................................4
Introduction ...............................................................................................................................................5
Specifications ............................................................................................................................................6
Unpacking .................................................................................................................................................7
Shipping Content .......................................................................................................................................7
Base Units .............................................................................................................................................7
Canister Filter Kit ....................................................................................................................................8
30 Micron Bag Filter Kit ...........................................................................................................................8
5 Micron Bag Filter Kit (Optional) .............................................................................................................8
Base Unit Assembly ...................................................................................................................................9
Base ......................................................................................................................................................9
Motor and Fan Assembly ........................................................................................................................9
Connector Housing .................................................................................................................................9
Cone Assembly .................................................................................................................................... 10
Hose.................................................................................................................................................... 10
Filter Bag Kit Assembly ............................................................................................................................ 11
Filter Bag Installation ............................................................................................................................ 11
Collector Bag Installation....................................................................................................................... 11
Canister Kit Assembly .............................................................................................................................. 12
Canister Filter ....................................................................................................................................... 12
Collector Bag ....................................................................................................................................... 12
Electrical Connections .............................................................................................................................. 13
Turning the Machine On & Off .................................................................................................................. 13
All Models ............................................................................................................................................ 13
Remote Control (Optional Accessory) .................................................................................................... 13
Turning the DC-RC230 On & Off ........................................................................................................... 13
Changing Operating Frequency ............................................................................................................. 14
Installing the DC-RC Remote Power Control .......................................................................................... 14
Maintenance............................................................................................................................................ 15
Cleaning the Filter Bag - DC-1200VX-BK1 and DC-1200VX-BK3 ............................................................. 15
Removing the Collector Bag – DC-1200VX-BK1 and DC-1200VX-BK3 .................................................... 15
Cleaning the Canister Filter – DC-1200VX-CK1 and DC-1200VX-CK3 ..................................................... 15
Removing the Collector Bag – DC-1200VX-CK1 and DC-1200VX-CK3 .................................................... 15
Motor ................................................................................................................................................... 15
Connecting the Dust Collector to a Machine ........................................................................................... 15
Grounding the Dust Collection System ................................................................................................... 15
Parts Breakdown for the DC-1200VX Dust Collector ............................................................................... 16
Ordering Replacement Parts..................................................................................................................... 17
Parts List for the DC-1200VX Dust Collector........................................................................................... 17
Canister Filter Kit (708639B) ................................................................................................................. 19
30 Micron Filter Bag Kit (708636F) ........................................................................................................ 20
5-Micron Filter Bag Kit (708636MF) Optional Accessory ......................................................................... 21
3
Warnings
1. Read and understand the entire owner's manual before attempting assembly or operation.
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of
these warnings may cause serious injury.
3. Replace the warning labels if they become obscured or removed.
4. This dust collector is designed and intended for use by properly trained and experienced personnel only. If
you are not familiar with the proper and safe operation of a dust collector, do not use until proper training and knowledge have been obtained.
5. Do not use this dust collector for other than its intended use. If used for other purposes, Walter Meier
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
6. Always wear approved safety glasses/face shields while using this dust collector. Everyday eyeglasses
only have impact resistant lenses; they are not safety glasses.
7. Before operating this dust collector, remove tie, rings, watches and other jewelry, and roll sleeves up past
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips are
recommended. Do not wear gloves.
8. Wear ear protectors (plugs or muffs) during extended periods of operation.
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain
chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
Lead from lead based paint.
Crystalline silica from bricks, cement and other masonry products.
Arsenic and chromium from chemically treated lumber.
Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.
12. Make certain the machine is properly grounded.
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches
are removed from the machine before turning it on.
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance purposes,
use extreme caution and replace the guards immediately.
16. Check damaged parts. Before further use of the machine, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
17. Provide for adequate space surrounding work area and non-glare, overhead lighting.
18. Keep the floor around the machine clean and free of scrap material, oil and grease.
19. Keep visitors a safe distance from the work area. Keep children away.
4
20. Make your workshop child proof with padlocks, master switches or by removing starter keys.
21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are
careless acts that can result in serious injury.
22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings,
metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector.
23. Use recommended accessories; improper accessories may be hazardous.
24. Maintain tools with care. Follow instructions for lubricating and changing accessories.
25. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do not
use yo ur hands.
26. Do not stand on the machine. Serious injury could occur if the machine tips over.
27. Never leave the machine running unattended. Turn the power off and do not leave the machine until it
comes to a complete stop.
28. Remove loose items and unnecessary work pieces from the area before starting the machine.
29. Never place hands near the inlet of the machine.
30. Always make certain machine is off and unplugged when making any connections to the inlet.
Familiarize yours elf with the f ollow ing saf et y not ices used in t his manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly even
death.
- - SAVE THESE I NSTRUCTI ONS - -
Introduction
This manual is provided by Walter Meier (Manufacturing) Inc., covering the safe operation and maintenance procedures for model DC-1200VX Series Dust Collectors. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This machine has been designed and constructed to provide years of trouble free operation if used in accordance to instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or Walter Meier (Manufacturing) Inc.
5
Specifications
Main Du st Collec tion Kit s
Model Number s Stock Numbers
DC-1200VX-BK1 (Single Phase, with 30 Micron Bag Filter Kit) .............. .....................................710701K
DC-1200VX-BK3 (Three Phase, with 30 Micron Bag Filter Kit) ............... .....................................710703K
DC-1200VX-CK1 (Single Phase, with Canister Filter Kit) ....................... .....................................710702K
DC-1200VX-CK3 (Three Phase, with Canister Filter Kit) ........................ .....................................710704K
Base Machine
Stock Number.............................................................................. 710701 ................................... 710703
Impeller Diameter ................................................................................ 12 .......................................... 12
Sound Rating at 3 foot distance .................................................. 70-80 db ................................. 70-80 db
1-Hose Connection Diameter (in.) ...........................................................6 ............................................ 6
2-Hose Connection Diameter (in.) ...........................................................4 ............................................ 4
Air Flow (CFM) ............................................................................... 1,200 ......................................1.200
Velocity at 4” (FPM) ...................................................................... 13,745 .................................... 13,745
Static Pressure (inch of water) ........................................................... 11.5 ....................................... 11.5
Overall Dimensions with Bag Filter installed-approx.(in.) ... 37L x 28W x 79H .................... 37L x 28W x 79H
Motor, TEFC ............................................................ 2HP, 1PH, 230V only ............... 2HP, 3PH, 230/460V
................................................................................................. 8A, 60Hz ...... Prewired 230V, 6/3A, 60Hz
Net Weight, approximate (lbs)............................................................. 127 ........................................ 127
30 Micron Filter Bag Kit
Stock Number......................................................................................................................... 708636F
Filter Bag Efficiency ...................................................................................... 96% of 30 micron particles
Filter Bag Length, installed (in.).......................................................................................................... 32
Filter and Collector Bag Diameter (in.) ................................................................................................ 20
Collector Bag Capacity (cu. ft.).......................................................................................................... 5.3
Collector Bag Length, installed (in.) .................................................................................................... 29
Canister Filter Kit
Stock Number......................................................................................................................... 708639B
Canister Length (in.).......................................................................................................................... 25
Canister Efficiency ................................................... 86% of 1 micron particles; 98% of 2 micron particles
Collector Bag Diameter (in.)............................................................................................................... 20
Collector Bag Capacity (cu. ft.).......................................................................................................... 5.3
Collector Bag Length, installed (in.) .................................................................................................... 29
5 Micron Filter Bag Kit ( Optional Accessory)
Stock Number...................................................................................................................... 708636MF
Filter Bag Efficiency .................................... 74% of 1 micron particles; 92% of 3 micron; 98% of 5 micron
Filter Bag Length, installed (in.).......................................................................................................... 32
Filter and Collector Bag Diameter (in.) ................................................................................................ 20
Collector Bag Capacity (cu. ft.).......................................................................................................... 5.3
Collector Bag Length, installed (in.) .................................................................................................... 29
IR Re mo te Control Unit (Optional Accessory)
Stock Number (main unit and remote control switch) (115V only) ............................................... 708636D
Stock Number (Remote Control Switch only) ............................................................................ 708636T
The above specifications were current at the time this manual was published, but because of our policy of continuous im provement, Walter Mei er (Manuf acturing) Inc., reserves the right to change specifications at any time and without prior noti ce, without incur r i ng obli gations .
Read and understand the ent ire cont ent s of t his manual bef ore at t emptin g set - up or operation! Failur e t o comply may cause seri ous in jury.
6
Unpacking
Shippi ng Cont ent
The table below lists the shipping cartons that are included with the various models of the DC-1200 Dust Collector.
1. Locate your particular model and verify that you
have received the all the correct cartons.
2. Check contents of each carton against the ship-
ping content listings on this and the following page.
3. Report any damage to your distributor.
4. Do not discard any shipping material until after
the dust collector has been assembled and is running properly.
Base Unit
(SN 710701)
Base Unit
(SN 710703)
30M Filter Bag
Kit (SN
708636F)
Canister Filter
Kit (708639B)
DC-1200VX-BK1 x x DC-1200VX-CK1 x x DC-1200VX-BK3 x x DC-1200VX-CK3 x x
Table – DC-1200VX Dust Coll ector c ar tons
Hardware Ba g for Base Unit
(SN DC1100-HP)
Base Uni t
(SN 710701 and 710703)
s
1 – Housing (A) 2 – Hose Clamps (B) 1 – Hose (C) 1 – Impeller (Motor/Fan Assembly) (D) 1 – Inlet Port (E) 1 – Impeller Cover (F) 3 – Support Legs (G) 1 – Base (H) 4 – Casters (J) 1 – Owner's Manual (not shown) 1 – Warranty Card (not shown) 1 – Hardware Bag Base Assly. (SN DC1100-HP) 1 – Hardware Bag, Cone Assly. (SN DC1100-HP2)
16 – M8 x 16 Hex Cap Screws (K) 22 – M8 Flat Washers (L)
08 – M6 x 12 Pan Head Flange Screws (M) 06 – M8 Hex Nuts (N)
Base Assembly Hardware
Hardware Bag for Cone Assembly
(SN DC1100-HP2)
1 – M8 x 16 Hex Cap Screw (O) 1 – M8 Flat Washer (P) 1 – M8 Hex Nut (R) 4 – M6 x 12 Hex Cap Screws (S) 4 – M6 Hex Nuts (T)
Cone Assembly Hardware
Base Machine Shi pping Contents
7
Cani st er Filter Kit
(SN 708639B)
1 – Handle (O) 1 – Canister Filter (P) 1 – Snap Ring (Q) 5 – Collector Bags (R) 1 – Canister Filter Hardware Bag (SN DC1100-CHP)
Contains: (2) M10 Hex Nuts (S) (2) M10 Flat Washers (T) (1) M10 Lock Washer (U) (4) Knobs (V)
30 M icron Bag Fi lter Kit
(SN 708636F)
1 – Upper Bag Hanger (Y) 1 – Hanger Bracket (Z) 1 – Collector Bag (X) 1 – Filter Bag (W) 1 – Retainer Strap (AA)
Canister Filter Kit Contents
Canister Filter Hardware
(SN DC1100-CHP)
30 Micr on Bag Fil ter Kit Contents
5 M icron Bag Fil t er Kit (Optional)
(SN 708636MF)
1 – Upper Bag Hanger (BB) 1 – Hanger Bracket (CC) 1 – Filter Bag (DD) 5 – Collector Bags (EE) 1 – Retainer Strap (FF) 1 – Snap Ring (GG)
Canister Filter Hardware
5 Micron Bag Filter Ki t Contents
8
Base Unit Assembly
Base
1. Install four casters to the under side of the base as
pictured in Fig. 2.
Referring to Figure 1:
2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft.
Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten
the nut (B) against the base with a 14mm wrench.
This will give t he caster proper clearance.
M otor and Fan Assembly
Referring to Figure 2:
3. Place the base (C) with casters on the ground. Attach the mo tor and f an assem bly (A) to the base
using four each M8 x 16 hex cap screws, and M8 flat washers (B). Tighten with a 13mm wrench.
Figure 1
Figure 2
The dust collector must not be connected to the power source during assembly. Failure to comply may resu lt in serious injury!
Referring to Figure 3:
4. Attach impeller cover (A) to fan housing (D) using
eight M6 x 12 pan head screws (B). Press the inlet ports (C) onto the inlet guard until it snaps into
place.
To reduce the risk of injury from moving parts, always keep inlet port covered with the caps provided, if they are not connected to a hose. Failure to comply may result in serious injury!
Connector Housing
5. Attach three support legs (A, Fig. 4) to the base
using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand-tighten only at this time.
Figure 3
Figure 4
9
6. Install the housing (A, Fig. 5) to two support
legs (B, Fig. 5) using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts (C,
Fig. 5). Be sure hose opening faces f an housing. Note: For models DC-1200VX-BK1 or DC-
1200VX-BK3 only – Before attaching third support
bracket, place the hanger bracket (D, Fig.5)
between the support bracket and the housing.
7. Tighten all nuts and bolts at this time with a 13mm
wrench.
Con e Assembly
Referring to Figure 6:
8. Mount the cone support bracket (E) to the housing
with four M6x12 hex cap screws (F), and tighten from beneath with four M6 hex nuts (G).
9. Install the cone (H) from beneat h using the M8x16
hex cap screw (J), M8 flat washer (K), and M8 hex nut (L), and tighten.
Figure 5
Hose
Referring to Figure 7:
10. Attach the hose (B) between the fan housing (A)
and the im peller housing (D) with two clamps (C).
Tighten the clamps to secure the hose.
This completes the Base Unit assembly. If you purchased the DC-1200VX-BK1 or DC-1200VX-BK3 Dust Collector (filter bag version), continue on the following page. If you purchased the DC-1200VX-CK1 or DC-1200VX-CK3 Dust Collector (canister filter version), proceed to Canister Kit Assembly section on
page 12.
Figure 6
Figure 7
10
Filter Bag Kit Assembly
If you purchased Model DC-1200VX-BK1 or DC­1200VX-BK3 Dust Collector, this section describes the assembly and installation of the contents of the 30 Micron Filter Bag Kit (SN 708636F). These instructions also apply to the optional 5 Micron Filter Bag Kit (SN 708636MF).
Filter Bag Installation
Referring to Figure 8:
1. Place the hanger (A) on the hanger bracket (B).
2. Slide the filter bag loop (C) over the hanger hook.
3. Feed the retainer strap (D) through the loops on
the filter bag (E) and fasten to the collector housing (F).
Collector Bag Installation
Referring to Figure 9:
4. Insert the ring of the collector bag (A) at an angle
into the housing (B) through the opening at the
bottom. Pull down on the bag to make sure it “seats” in the housing.
5. Position the plastic window in front so that you can
easily see when the collector bag is full.
Figure 8
After completing the filter bag and collector bag
installation, proceed to Electrical Connections.
Figure 9
11
Canister Kit Assembly
If you purchased Model DC-1200VX-CK1 or DC­1200VX-CK3 Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708636F).
Cani st er Filter
1. Mount the handle onto the canister filter with two
M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 10).
2. Mount the canister filter on top of the collector
housing (A, Fig. 5) and tighten the knobs on the canister f il ter (Figure 10).
Figure 10
Col l ect or Bag
3. Place the ring over the top of the plastic bag and
fold over the bag approximately three inches, Figure 11.
4. Insert the snap ring (A, Fig. 12) of the collector
bag into the bottom of the housing at an angle.
5. Pull down on the ring to make sure it “seats” in the
housing.
Note: make sure the snap ring “snaps” into place
in the housing, and also that the plastic bag hangs down approximately 3” so that there are no air leaks.
Figure 11
Figure 12
12
Electrical Connections
Dust Collector RF Remote
All electrical connections must
be done by a qualified electri­cian. All adjustments or repairs must be done with the dust collector disconnected from the power source, unplugge d. Failure to comply may res u lt in serious inju ry!
The DC-1200VX single phase dust collectors are rated for 230V Only. The dust collector is not
supplied with a plug. Use a plug and outlet rated at least 20 amps. The circuit for the machine should also be protected by at least a 20 amp circuit breaker or fuse.
The DC-1200VX three phase dust collectors are rated for 230V/460V, Prewired 230V. If you wish to
run these on 460 volt, refer to the wiring diagram found on the inside of the switch box cover.
Keep in mind that a circuit being used by other machines, tools, lights, heaters, etc. at the same time will add to the electrical load. A dedicated circuit to the dust collector will give you the best results since dust collectors are generally used at the same time other tools are running.
Turning the Machine On & Off
This machine is intended f or indoor use only.
All Models
Before hooking up to the power source, make sure that the switch is in the off position.
Turn the dust collector on by pressing the Start button mounted next to the motor. Press the Stop
button to turn off the dust collector.
Power Control (optional)
The DC-RC230 Remote Power Control (Figure 14)
should be used for activating Dust Collection units
powered by 230V only up to 3HP, 1 Phase. The DC­RC230 Remote Power Control unit is rated at 230V, Single Phase only. Use an outlet rated at least
20amps. The circuit for the device being controlled by
the DC-RC230 s hould also be protected by at least a
20 amp circuit breaker or fuse.
Before hooking up to the power source, make sure that the switch is initially in the off position on both
the dust collector and remote control unit (Figure 13).
Turning the DC-RC230 On & Off
This machine is intended f or indoor use only.
1. Plug the dust collector into the main unit
(Figure 14) and plug the main unit into the power outlet.
To start a machine or device:
2. Turn the machine itself on.
3. On the main unit place the switch to the ON
position (Figure 13A). The red LED on the main unit should lig ht up.
4. Press the button on the remote control transmitter (Figure 14) to turn the machine on.
5. To stop the machine, press the button on the
re mote co n trol transmitte r again.
Remote Co ntrol ( Opti on al Accessory)
The DC-RC230 RF Remote Power Control unit is available as an optional accessory (contact Customer Service by calling the number on the cover).
Important: The DC-RC230 Remote Power Control
can be used for activating Dust Collection units
powered by 230V only up to 3HP, single phase only.
Figure 13A Figure 13B
Figure 14
When the machine is running, it can be stopped by placing the switch on the main unit in the off position (Figure 14). To restart, repeat steps 3 and 4.
13
Chan ging Operat i ng Frequency
If several devices are controlled by the same type remote control unit, each remote control unit can be set to operate at its' own unique operating frequency as follows:
Referring to Figure 15:
1. Unplug the DC-RC230 Remote Power Control
unit.
2. Remove the back covers of the main unit (A) and remote control switch (B).
3. Locate the DIP switch (C) in each unit.
4. Change the position of the DIP switches in the
main uni t (A) to any combination desired as long
as they are not the same as other units that may be present and located within the radio frequency range.
5. Set the DIP switches (C) in the remote control
switch (B) to match the switch settings in the main unit (A).
6. Replace the back covers to the main unit and remote control switch.
7. Operate a device as described in Turning the DC-RC230 On & Of f and verify that other devices
using the same type remote control do not turn on.
To mount the DC-RC230 Remote Power Control
(refer to Figure 16):
Note: Mounting hardware is not included and must
be supplied by the machine’s owner or user.
1. Place RC Power Control Unit (A) on the open clearing of the base (B) of the dust collector near the motor (C).
2. Using a marker, mark the base through the mounting holes of the power control units mounting tabs.
3. Drill two holes (D) through the base where marked.
4. Insert screws through the tabs and base. Place washers and hex nuts on the threaded ends of the screw underneath the base and tighten.
Figure 15
Installing the DC-RC Remote Power Control
The DC-RC230 Remote Power Control unit can be
placed anywhere for convenience and portability if used to control other machines or it can be mounted as a permanent part of a machine, such as the DC­1200VX Dust Collector.
Figure 16
14
Maintenance
Clean i ng th e Canister F il t er – DC- 1200VX­CK1 and DC-1200VX-CK3
Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injur y!
Clean i ng th e Fi lter Bag - DC- 1200VX-BK1 and DC- 1200V X-BK3
Wearing a particle mask or respirator for protection against fine dust particles dur ing cle ani ng is hi ghly recommended.
During first use and after cleaning, the filter bag may allow some dust to escape. This is normal and will stop after a short period of time.
Clean both the filter and collector bags frequently to keep the collector's performance at its optimum. To clean:
1. Disconnect the machine from the power source.
2. Unhook the filter bag from the hanger and shake
the bag so that the majority of the dust falls into the collector bag.
3. Loosen the retaining strap, and remove the filter
bag from the housing.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and re-attach to the
housing using the retainer strap to secure.
Removi n g the Co llecto r Bag – DC-1200VX-BK1 and DC-1200VX-BK3
1. Disconnect the machine from the power source.
2. Remove the collector bag by pushing the ring of
the collector bag upwards and pulling the bag out at an angle.
3. Empty the contents into an appropriate
container.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and insert into the
housing.
To replace the collector bag, refer to Collector Bag Installation on page 11.
Never perform maintenance on this machine before turning switch off and removing plug from power source. Failure to comply may cause serious injur y!
Clean both the filter and collector bags frequently to keep the collector's performance at its optimum.
To clean the filter, turn the handle a couple of rotations so the dust falls into the collector bag.
Removi n g the Co llecto r Bag – DC-1200VX-CK1 and DC-1200VX-CK3
Wearing a particle mask or respirator for protection against fine dust particles dur ing cle ani ng is hi ghly recommended.
1. Disconnect the machine from the power source
outlet.
2. Remove the collector bag by pushing the ring of
the collector bag upwards at an angle and pulling the bag and snap ring out.
3. Empty the contents into an appropriate
container.
To replace the collector bag, refer to the Collector Bag section on page 12.
Motor
Make frequent inspections of the motor fan and blow out (with low pressure air hose) or vacuum any accumulation of foreign material in order to maintain normal motor ventilation.
Con necting the Dust Co llecto r t o a Machine
Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Customize your installation and obtain maximum performance with JET's dust hoods, hoses, clamps, fittings, and blast gates.
Use the proper type hose to connect the dust collector to the machine being operated. Dryer vent hose is not acceptable for this purpose. Contact your
nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Customize your
installation and obtain maximum performance with JET's dust hoods, hoses, clamps, fittings, and blast gates.
Grounding the Dust Collection System
The dust collection system includes the dust collector and the hose, or ductwork you use to connect the tools. The dust collector is grounded through the ground wire in the cord. The hose or ductwork you use to connect the tool to the dust collector must also be grounded.
15
Parts Breakdown for the DC-1200VX Dust Collect or
 16
Orderi ng Replacement Parts
To order parts or reach our service department, call 800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Parts L i st f or the DC-1200V X Dust Col lector
Index No. Part No. Description Size Qty
1 .............. 411035W ................Impeller Housing............................................................................................. 1
2 .............. 411026W ................Motor Bracket ................................................................................................. 1
3 .............. 998621....................Strain Relief ................................................................................................... 1
4 .............. MA411003...............Motor ...............................................................2 HP, 1Ph .............................. 1
................ MA411003-3............Motor ...............................................................2 HP, 3 Ph ............................. 1
................ DC1100-50W...........Motor Fan Cover (not shown) .......................................................................... 1
................ MF411012 ...............Motor Fan (not shown) .................................................................................... 1
................ CA003030 ...............Running Capacitor (not shown)..........................30MFD, 300V ......................... 1
................ CA020010 ...............Starting Capacitor (not shown)...........................200MFD, 125V ....................... 1
5 .............. 411051....................Switch Box ..................................................................................................... 1
6 .............. 411053....................Switch Plate ................................................................................................... 1
7 .............. 994542....................Switch ..............................................................1 Ph ....................................... 1
................ DC1900-23B ...........Switch ..............................................................3 Ph ....................................... 1
8 .............. IC420002 ................Power Cord ......................................................1 Ph ....................................... 1
................ IC420002-3 .............Power Cord ......................................................3 Ph ....................................... 1
9 .............. 420051....................Motor Packing ................................................................................................ 1
10 ............ AB411059 ...............Impeller ............................................................12” ......................................... 1
11 ............ 411036W ................Inlet Guard ..................................................................................................... 1
12 ............ 427028....................Inlet Port ..........................................................2 @ 4”.................................... 1
13 ............ 420203....................Inlet Cap ........................................................................................................ 2
14 ............ 430034....................Inlet Flange Packing ....................................................................................... 1
15 ............ 411041W ................Base .............................................................................................................. 1
16 ............ 402036....................Pivoting Caster ............................................................................................... 4
17 ............ 420012W ................Housing ......................................................................................................... 1
18 ............ 402004W ................Support .......................................................................................................... 3
20 ............ 411009....................Hose ................................................................5”x65(CM) .............................. 1
21 ............ 420010....................Ring Clamp ......................................................5”........................................... 2
31 ............ ST039304 ...............Tapping Screw .................................................M3.5x12(AB) .......................... 6
32 ............ KS050525 ...............Key ..................................................................5x5 x25 ................................... 1
34 ............ TS-1540061 ............Nut ..................................................................M8 ....................................... 10
35 ............ TS-0561031 ............Nut ..................................................................3/8”-16UNC ............................ 4
36 ............ SH080402 ...............Hex Head Bolt ..................................................M8x20 L.H ............................. 1
37 ............ TS-1490011 ............Hex Head Bolt ..................................................M8x12.................................... 4
38 ............ TS-1490021 ............Hex Head Bolt ..................................................M8x16.................................. 16
39 ............ TS-1490041 ............Hex Head Bolt ..................................................M8x25.................................... 4
40 ............ TS-1554041 ............Pan Head Bolt W/Flange ...................................M6x12.................................... 2
41 ............ TS-0680031 ............Flat Washer......................................................M8 ......................................... 1
42 ............ TS-1554041 ............Pan Head Bolt W/Flange ...................................M6x12.................................... 8
43 ............ TS-0680031 ............Flat Washer ......................................................M8 ....................................... 34
44 ............ TS-0720081 ............Spring Washer..................................................M8 ......................................... 8
45 ............ TS-1551071 ............Spring Washer..................................................M10 ....................................... 4
46 ............ ST059304 ...............Tapping Screw .................................................M5x12.................................... 2
47 ............ DC1100-47 ..............Cone.............................................................................................................. 1
48 ............ DC1100-47-1 ...........Support Bracket .............................................................................................. 1
49 ............ TS-1490021 ............Hex Cap Screw ................................................M8x16.................................... 1
50 ............ TS-1550061 ............Flat Washer......................................................M8 ......................................... 1
51 ............ TS-1540061 ............Hex Nut............................................................M8 ......................................... 1
52 ............ TS-1482021 ............Hex Head Bolt .................................................M6x12.................................... 4
53 ............ TS-2311061 ............Hex Nut............................................................M6 ......................................... 4
 17
Index No. Part No. Description Size Qty
................ DC1200A-NP...........Name Plate (not shown) .................................................................................. 1
................ DC1100-HP .............Hardware Package (not shown) ....................................................................... 1
................ DC1100-HP2 ...........Hardware Package for cone assy (index # 49 thru 53)....................................... 1
................ DC1200A-CS...........Centrifugal Switch (not shown) ........................................................................ 1
................ DC1900-53 ..............Warning Label (not shown) .............................................................................. 1
................ DC1200-53 ..............Grounding Label (not shown)........................................................................... 1
................ DC1200-54 ..............Direction Label (not shown) ............................................................................. 1
 18
Cani st er Filter Kit (70863 9B)
Index No. Part No. Description Size Qty
................ 708639B................. Canister Filter Kit (i ndex #1- 24)......................... ...............................................
1 .............. 331050 ................... Handle ............................................................ ..............................................1
2 .............. TS-1540071............ Hex Nut ........................................................... M10 .......................................2
3 .............. TS-1550071............ Flat Washer ..................................................... M10 .......................................2
4 .............. TS-2361101............ Lock Washer ................................................... M10 .......................................1
5 .............. BR000052 .............. Rivet ............................................................... 5-2 .........................................3
6 .............. 331014 ................... Bracket ........................................................... ..............................................1
7 .............. 150623 ................... Pad ................................................................. ..............................................1
8 .............. 331051 ................... Soft Grip Handle .............................................. ..............................................2
9 .............. TS-1540041............ Hex Nut ........................................................... M6 .........................................8
10 ............ 708739 ................... Filter ............................................................... ..............................................1
11 ............ 331052 ................... Shaft ............................................................... ..............................................1
12 ............ TS-1482041............ Hex Cap Screw................................................ M6X20 ...................................4
13 ............ TS-2361061............ Lock Washer ................................................... M6 .........................................4
14 ............ TS-1550041............ Flat Washer ..................................................... M6 .........................................4
15 ............ 331012 ................... Scraper ........................................................... ..............................................2
16 ............ 331017 ................... Strip ................................................................ ..............................................2
17 ............ 331015 ................... Press Plate ...................................................... ..............................................2
18 ............ TS-1482021............ Hex Cap Screw................................................ M6x12 ....................................4
19 ............ 331037 ................... Knob ............................................................... ..............................................4
20 ............ 331031 ................... Pad ................................................................. ..............................................1
21 ............ 331009 ................... Support ........................................................... ..............................................1
22 ............ ST049200............... Tapping Screw................................................. M4X8 .....................................4
23 ............ 331038 ................... Snap Ring ....................................................... ..............................................1
24 ............ 709563 ................... Plastic Bag ...................................................... ..............................................5
..................DC1100-CHP...........Canister Hardware Package....................................................................................
 19
30 M icron Filter Bag Ki t ( 708636F)
Index No. Part No. Description Size Qty
................ 708636F ................. 30 Micron Filter Bag Kit (i ndex #1- 5) ................. ...............................................
1 .............. 708698 ................... Filter Bag ........................................................ 30 Micron Bag ........................1
2 .............. AB410012 .............. Retainer Strap ................................................. ..............................................1
3 .............. 708699A................. Collection Bag ................................................ ..............................................1
4 .............. 430038 ................... Hanger ............................................................ 30 Micron Bag Hanger ............1
5 .............. 523011W................ Hanger Bracket................................................ ..............................................1
 20
5-Micron Fi lter Bag Ki t ( 708636MF) Op t ional Accesso ry
Index No. Part No. Description Size Qty
................ 708636MF ...............5-Micron Filter and Collection Bag Kit (index # 1-6) .............................................
1 .............. 708706....................Filter Bag ........................................................5 Micron ................................. 1
2 .............. AB410012 ...............Retainer Strap ................................................................................................ 1
3 .............. 331038....................Snap Ring ...................................................................................................... 1
4 .............. 709563....................Plastic Bag (Package of 5) .............................................................................. 1
5 .............. 430038....................Hanger .......................................................................................................... 1
6 .............. 523011W ................Hanger Bracket .............................................................................................. 1
 21
Wiring Diagram For 3 Phase 230/460V Dust Collector (DC-1200VX)
Wiring Diagram For Single Phase 230V Only Dust Collector (DC-1200VX)
 22
 23
WALTER MEIER (Manuf acturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.waltermeier.com
24
Loading...