This .pdf document is bookmarked
Operating Instructions and Parts Manual
AFS-2000 Air Filtration
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-708615
Ph.: 800-274-6848 Revision B2 10/2018
www.jettools.com Copyright © 2014 JET
IMPORTANT SAFETY INSTRUCTIONS
WARNING – To reduce risk of injury:
1. FOR YOUR OWN SAFETY, READ INSTRUCTION MANUAL BEFORE OPERATING THE TOOL.
Learn the tool’s application and limitations as well as the specific hazards peculiar to it.
2. KEEP GUARDS IN PLACE and in working order.
3. ALWAYS WEAR EYE PR O TECTION.
4. GROUND ALL TOOLS. If tool is equipped with three prong plug, it should be plugged into a threehole electrical receptacle. If an adapter is used to accommodate a two prong receptacle, the adapter
lug must be attached to a known ground. Never remove the third prong.
5. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
6. DON’T USE IN DANGEROUS ENVI RO NMENT. Don’t use power tools in damp or wet locations, or
expose them to rain. Keep work area well-lighted.
7. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance
from work area.
8. MAKE WORKSHOP CHILDPROOF. Use padlocks, master switches, or remove starter keys.
9. DON’T FORCE TOOL. It will do the job better and be safer at the rate for which it was designed.
10. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
11. WEAR PROPER APPAREL. No loose clothing, gloves, neckties, rings, bracelets, or other jewelry to
get caught in moving parts. Nonslip footwear is recommended. Wear protective hair covering to
contain long hair.
12. ALWAYS USE SAFETY GLASSES. Wear safety glasses (must comply with ANSI Z87.1). Everyday
eyeglasses only have impact resistant lenses; they are not safety glasses. Also use face or dust
mask if cutting operation is dusty.
13. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hands
and frees both hands to operate tool.
14. DON’T OVERREACH. Keep proper footing and balance at all times.
15. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
16. DISCONNECT TOOLS before servicing and when changing filters.
17. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not
recommended by manufacturer may cause hazards or risk of injury to persons.
18. AVOID ACCIDENTAL STARTING. Make sure switch is in “OFF” position before plugging in power
cord.
19. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the fan blade is
accidentally contacted.
20. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged
should be carefully checked to ensure that it will operate properly and perform its intended functioncheck for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other part that is damaged should be
properly repaired or replaced.
21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it
comes to a complete stop.
22. DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol
or any medication.
2
23. MAKE SURE TOOL IS DICONNECTED FROM POWER SUPPLY while motor is being mounted,
connected or reconnected.
WARNING: This product can expos e you to ch emic als includi ng lead which is kno wn to the Stat e
of California to ca us e c anc er an d b irth defects or other r eproduc t ive har m. For more inform ation go to
http://www.p65warnings.ca.gov.
WARNING: Drilling, sa wing, sandi ng or mac hining wood produc ts generates wood dust and ot her
substances known to the State of California to cause cancer. Avoid inhaling dust generated from
wood products or use a dust mask or other safeguards for personal protection.
Wood products emit chemicals known to the State of California to cause birth defects or other
reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.
-- SAVE THESE INSTRUCTIONS --
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious or even fatal
injury.
Safety Rules for the AFS-2000
1. Read and understand instruction manual before installing or operating air cleaner.
2. To reduce the risk of injury disconnect the air cleaner from the power source (unplug) before servicing
or changing filters.
3. If ceiling mounted, bottom of air cleaner must be at least 7 feet above the floor.
4. If ceiling mounted, mounts must be anchored to building structure which will support a minimum of at
least 220 pounds. Never mount to surfaces such as dry wall or false ceiling grids, etc.
5. To reduce the risk of electrical shock, do not expose air cleaner to water or rain.
6. Never duct a machine directly into the air cleaner.
7. To avoid a potentially dangerous situation, do not use this equipment to filter volatile fumes or smoke.
This air cleaner is designed and intended for the filtration of air borne wood dust only. It is neither
designed nor intended for an y other purpose wha tsoe v er .
8. Failure to comply may result in serious injury and / or property damage.
3
Table of Contents
IMPORTANT SAFETY INSTRUCTIONS .............................................................................................................. 2
Safety Rules for the AFS-2000 ............................................................................................................................. 3
Table of Contents .................................................................................................................................................. 4
Introduction ........................................................................................................................................................... 4
Specifications ........................................................................................................................................................ 4
Electrical Requirements ........................................................................................................................................ 5
Unpacking ............................................................................................................................................................. 6
Contents of Shipping Carton ............................................................................................................................. 6
Assembly ............................................................................................................................................................... 6
Controls and Features ........................................................................................................................................... 7
Changing the Filters .............................................................................................................................................. 7
AFS-2000 Parts Breakdown .............................................................................................................................. 9
AFS-2000 Parts List ........................................................................................................................................ 10
Electrical Connections ......................................................................................................................................... 11
Warranty and service .......................................................................................................................................... 12
Introduction
This manual is provided by JET covering the safe operation and maintenance procedures for a JET Model
AFS-2000 Air Filtration Unit. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. This machine has been designed and
constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this
manual. If there are any questions or comments, please contact either your local supplier or JET. JET can also
be reached at our web site: www.jettools.com.
Register your product using the mail-in card provided, or register online:
http://www.jettools.com/us/en/service-and-support/product-registration/
Specifications
Model Number ......................................................................................................................................... AFS-2000
Stock Number ............................................................................................................................................. 708615
Outer Filter .............................................................................................................................................. 5 Microns
Inner Filter ................................................................................................................................................. 1 Micron
Overall Dimensions (LxWxH/in) .......................................................................................................... 44 x 24 x 20
Sound Rating @ 3ft ................................................................................................................. High Speed 73.8 dB
.......................................................................................................................................... Medium Speed 62.0 dB
................................................................................................................................................. Low Speed 59.1 dB
Air Flow .............................................................................................................................. High Speed 1700 CFM
...................................................................................................................................... Medium Speed 1200 CFM
.............................................................................................................................................. Low Speed 800 CFM
Filter Cycle ..................................................................................................................................... 1.88 per minute
Cycles (20’x20’x8’) ........................................................................................................................... 31.91 per hour
Motor .............................................................................................................................. 1/3 HP, 115V, 115V Only
Shipping Size (LxWxH/in) ................................................................................................................... 46 x 26 x 22
Net Weight ................................................................................................................................................. 110 lbs.
Shipping Weight ............................................................................................................... .......................... 121 lbs.
The above specifications were current at the time this manual was published, but because of our policy of
continuous improvement, JET reserves the right to change spec ifications at any time and without prior notice,
without incurring obligations.
4
Loading...