Assembly Instructions and Parts Manual
5C Collet Closer for E-1236VS ELITE Lathe
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-892006
Ph.: 800-274-6848 Edition 1 03/2017
www.jettools.com Copyright © 2017 JET
1
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1. Read and understand the entire owner's
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace warning labels if they become
obscured or removed.
4. Familiarize yourself thoroughly with the
operation and safety instructions in your lathe
manual before using this collet closer.
5. This lathe accessory is designed and intended
for use by properly trained and experienced
personnel only. If you are not familiar with the
proper and safe operation of a lathe, do not use
until proper training and knowledge have been
obtained.
6. Do not use this product for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
7. Always wear ANSI Z87.1 approved safety
glasses or face shield while using a lathe.
(Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
8. Before operating the lathe, remove tie, rings,
watches and other jewelry, and roll sleeves up
past the elbows. Do not wear loose clothing.
Confine long hair. Non-slip footwear or anti-skid
floor strips are recommended. Do not wear
gloves.
9. Wear ear protectors (plugs or muffs) if noise
exceeds safe levels.
10. CALIFORNIA PROPOSITION 65 WARNING:
This product contains chemicals known to the
State of California to cause cancer, or birth
defects or other reproductive harm.
11. This product, when used for welding, cutting, or
working with metal, produces fumes, gases, or
dusts which contain chemicals known to the
State of California to cause birth defects and, in
some cases, cancer. (California Health and
Safety Code Section 25249.5 et seq.)
12. Make certain the switch is in the OFF position
before connecting the machine to the power
supply.
13. Make certain the machine is properly grounded.
14. Make all machine adjustments or maintenance
with the machine unplugged from the power
source.
15. Remove adjusting keys and wrenches. Form a
habit of checking to see that keys and adjusting
wrenches are removed from the machine
before turning it on.
16. Keep safety guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
17. Check damaged parts. Before further use of the
machine, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced.
18. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
19. Keep the floor around the machine clean and
free of scrap material, oil and grease.
20. Keep visitors a safe distance from the work
area. Keep children away.
21. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
22. Give your work undivided attention. Looking
around, carrying on a conversation and “horseplay” are careless acts that can result in serious
injury.
23. Maintain a balanced stance at all times so that
you do not fall or lean against the cutter or other
moving parts. Do not overreach or use
excessive force to perform any machine
operation.
24. Use the right tool at the correct speed and feed
rate. Do not force a tool or attachment to do a
job for which it was not designed. The right tool
will do the job better and more safely.
25. Use recommended accessories; improper
accessories may be hazardous.
26. Maintain tools with care. Keep cutting tools
sharp and clean for the best and safest
performance. Follow instructions for lubricating
and changing accessories.
2
27. Turn off the machine before cleaning. Use a
brush or vacuum to remove chips or debris —
do not use bare hands.
28. Do not stand on the machine. Serious injury
could occur if the machine tips over.
29. Never leave the machine running unattended.
Turn the power off and do not leave the
machine until it comes to a complete stop.
30. Remove loose items and unnecessary work
pieces from the area before starting the
machine.
31. Do not attempt to adjust or remove tools during
operation.
32. Never stop a rotating chuck or workpiece with
your hands.
33. Choose a low spindle speed when working
unbalanced workpieces, and for threading and
tapping operations.
34. Do not exceed the maximum speed of the
workholding device.
35. Do not exceed the clamping capacity of the
chuck or collet.
36. Workpieces longer than 3 times the chucking
diameter must be supported by the tailstock or
a steady rest.
37. Avoid small chuck diameters with large turning
diameters.
38. Avoid short chucking lengths and small
chucking contact.
39. Do not operate the lathe in flammable or
explosive environments. Do not use in a damp
environment or expose to rain.
3
2.0 Assembly
Note: The following illustrations may or may not
show your specific lathe model.
1. Disconnect machine from power source.
2. Unpack and clean all rust protected surfaces
with a mild solvent or kerosene. Do not use
paint thinner, lacquer thinner, or gasoline, as
these items will damage painted surfaces.
3. Turn cam locks (A, Figure 1) to release chuck.
Remove chuck and place it on a piece of wood.
Figure 1
4. Clean spindle nose and internal taper
thoroughly.
5. Screw coupling assembly (A, Figure 2) onto
spindle threads located at rear of spindle.
Adjustments can be made by loosening three
socket head cap screws (C, Figure 2).
8. Thread drawbar (A, Figure 3) into collet closer
assembly (B, Figure 3) until it is flush with the
assembly.
Figure 3
9. Slide collet closer assembly into spindle. Make
sure it completely engages castled gear on the
coupling.
10. Insert collet sleeve into spindle nose (A, Figure
4).
11. Insert collet (B, Figure 4).
Figure 2
6. Tighten coupling in place using three hex
socket screws (B, Figure 2).
7. Measure runout on coupling using a dial
indicator. Runout should be 0.005” or less.
Figure 4
12. Screw collet closer into collet by releasing collet
closer assembly lock and turning collet closer
outer flange (B, Figure 3) clockwise. Note: It is
4
necessary to push in collet while turning closer
body to engage draw bar with collet. Continue
turning until collet taper is seated, but not
tensioned in the taper.
13. Assemble all linkage and attach to collet closer
body (Figure 5).
Figure 5
14. With the help of another person, hold the collet
closer in position with the fixed seat against the
headstock. Note: The bearing shaft should be
centered in bearing body (Figure 5).
15. Once the location of the fixed seat has been
determined (should be similar to location shown
in Figure 6), use a transfer punch to mark the
location of the four mounting holes.
16. Drill four appropriate sized holes with a 0.203
drill bit. Note: Do not drill through headstock
panel.
17. Tap drilled holes with a 1/4”-20 tap.
18. Install fixed seat to headstock with f our 1/4”-20
x 3/4” hex socket cap screws, and four 1/4" lock
washers.
19. Connect and adjust all linkage so that bearing
shaft is centered in bearing body (Figure 5).
20. Place a cutter or material into collet so you can
adjust the outward flange (B, Figure 3). Turn
outward flange until you can move the lever and
it “pops” into place, locking the cutter or material
into the collet.
Figure 6
(measurements shown for reference only; your
lathe model measurements may vary slightly.)
3.0 Replacement Parts
Replacement parts are listed on the following pages. To order parts or reach our service department, call 1-800274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of
your machine available when you call will allow us to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually.
5
3.1.1 Collet Closer for E-1236VS Lathe – Exploded View
3.1.2 Collet Closer for E-1236VS Lathe – Parts List
Index No Part No Description Size Qty
.................. 892006 ...................... 5C Collet Closer Kit (includes #1 thru 30)................ ........................................
1 ................ C510350 .................... Sleeve Coupling ...................................................... .................................. .... 1
2 ................ C52302004 ................ Fixed Seat (Length) ................................................. ...................................... 1
3 ................ C53004118 ................ Sleeve ...................................................................... #5 .................................. 1
4 ................ C54002038 ................ Coupling .................................................................. ...................................... 1
5 ................ C54004047 ................ Arbor ........................................................................ ...................................... 1
6 ................ C54006001 ................ Buckle ...................................................................... ...................................... 3
7 ................ C54008007 ................ Buckling Plate .......................................................... ...................................... 1
8 ................ C54012019 ................ Outward Flange ....................................................... ...................................... 1
9 ................ C54014002 ................ Bearing Shaft ........................................................... ...................................... 1
10 .............. C54016011 ................ Bearing Stand .......................................................... ...................................... 1
11 .............. C54018020 ................ Collar ....................................................................... ...................................... 1
12 .............. C54020023 ................ Bearing Body ........................................................... ...................................... 1
13 .............. C54021000 ................ Socket Set Screw .................................................... ...................................... 2
14 .............. C54025015 ................ Coupling .................................................................. ...................................... 2
15 .............. C54026005 ................ Special Pin ............................................................... ................................. ..... 2
16 .............. C540271 .................... Stud ......................................................................... 105L mm ....................... 1
17 .............. C54029208 ................ Lever Shaft .............................................................. 205L mm ....................... 1
18 .............. C55440000 ................ Draw Bar .................................................................. 440L mm ....................... 1
19 .............. BB-6208ZZ ................ Ball Bearing ............................................................. 6208ZZ ......................... 1
20 .............. SB-6MM .................... Steel Ball.................................................................. Ø6.0mm ........................ 1
21 .............. 5510484 .................... Spring Pin ................................................................ 5 x 20L .......................... 1
22 .............. F012000 .................... Spring Pin ................................................................ 1/4"x1-1/2L .................... 3
23 .............. F006053 .................... C-Retaining Ring, Ext .............................................. 32mm ............................ 1
24 .............. GD020596 ................. Grip .......................................................................... 1/2" ................................ 1
25 .............. GE040176 ................. Spring ...................................................................... ...................................... 1
26 .............. TS-1501021 .............. Hex Socket Cap Screw ........................................... M4 x 8L ......................... 3
27 .............. TS-1523031 .............. Socket Set Screw .................................................... M6 x 10L ....................... 3
28 .............. GF030823 ................. Locking Nut .............................................................. AN08 ............................. 1
29 .............. TS-0570021 .............. Hex Nut .................................................................... 5/16”-18 ........................ 2
30 .............. TS-0561051 .............. Hex Nut .................................................................... 1/2”-13 .......................... 3
6
4.0 Warranty and service
JET® warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please
contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.
Warranty Period
The general warranty lasts for the time period specified in the literature included with your product or on the official
JET branded website.
• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)
• Accessories carry a limited warranty of one year from the date of receipt.
• Consumable items are defined as expendable parts or accessories expected to become inoperable within a
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.
Who is Covered
This warranty covers only the initial purchaser of the product from the date of delivery.
What is Covered
This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty
does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear,
improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood.
Use of these machines in the processing of metal, plastics, or other materials outside recommended guidelines may
void the warranty. The exceptions are acrylics and other natural items that are made specifically for wood turning.
Warranty Limitations
Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a
Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.
How to Get Technical Support
Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof
of initial purchase when calling. If a product requires further inspection, the Technical Service representative will
explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the
United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service
Center Locator on the JET website.
More Information
JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor
or visit the JET website.
How State Law Applies
This warranty gives you specific legal rights, subject to applicable state law.
Limitations on This Warranty
JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT.
EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR
INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR
PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are
given as general information and are not binding. JET reserves the right to effect at any time, without prior notice,
those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason
whatsoever. JET
Product Listing with Warranty Period
90 Days – Parts; Consumable items
1 Year – Motors; Machine Accessories
2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used
for industrial or commercial purposes
5 Year – Woodworking Machinery
Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist
Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools
NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries,
Inc., or any of its successors in interest to the JET brand.
®
branded products are not sold in Canada by JPW Industries, Inc.
7
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.jettools.com
8
Loading...