JET 756018 User Manual
Operating Instructions and Parts Manual
Manual Shrinker/Stretcher
Model MSS-1
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-756018
Ph.: 800-274-6848 Edition 1 09/2016
www.jettools.com Copyright © 2016 JET
1.0 IMPORTANT SAFETY
INSTRUCTIONS
WARNING – To reduce risk of injury:
1. Read and understand the entire owner’s
manual before attempting assembly or
operation.
2. Read and understand the warnings posted on
the machine and in this manual. Failure to
comply with all of these warnings may cause
serious injury.
3. Replace warning labels if they become
obscured or removed.
4. This shrinker/stretcher is designed and
intended for use by properly trained and
experienced personnel only. If you are not
familiar with the proper and safe operation of a
shrinker/stretcher, do not use it until proper
training and knowledge have been obtained.
5. Do not use this machine for other than its
intended use. If used for other purposes, JET
disclaims any real or implied warranty and holds
itself harmless from any injury that may result
from that use.
6. Always wear ANSI Z87.1 approved safety
glasses or face shield while using this machine.
(Everyday eyeglasses only have impact
resistant lenses; they are not safety glasses.)
7. Before operating the machine, remove tie,
rings, watches, other jewelry, and roll sleeves
up past the elbows. Remove all loose clothing
and confine long hair.
8. Keep the floor around the machine clean and
free of scrap material, oil and grease.
9. Keep machine guards in place at all times when
the machine is in use. If removed for
maintenance purposes, use extreme caution
and replace the guards immediately after
completion of maintenance.
10. Do not over reach. Maintain a balanced stance
at all times, so that you do not fall or lean
against moving parts.
11. Use the right tool. Do not force a tool or
attachment to do a job that it was not designed
to do.
12. Give your work undivided attention. Looking
around, carrying on a conversation and "horseplay" are careless acts that can result in serious
injury.
13. Keep visitors a safe distance from the work
area. Keep children away.
14. Make your workshop child proof with padlocks,
master switches or by removing starter keys.
15. Use recommended accessories; improper
accessories may be hazardous.
16. CALIFORNIA PROPOSITION 65 WARNING:
This product contains chemicals known to the
State of California to cause cancer, or birth
defects or other reproductive harm.
17. This product, when used for welding, cutting, or
working with metal, produces fumes, gases, or
dusts which contain chemicals known to the
State of California to cause birth defects and, in
some cases, cancer. (California Health and
Safety Code Section 25249.5 et seq.)
18. Do not operate this machine while under the
influence of drugs, alcohol or any medication.
19. Keep tools sharp and clean for safe and best
performance.
20. Provide for adequate space surrounding work
area and non-glare, overhead lighting.
21. Use only JET factory authorized replacement
parts and accessories; otherwise, the warranty
and guarantee are null and void.
22. Use caution handling metal workpieces. Wear
leather gloves to prevent cuts from sharp
edges.
23. Keep fingers away from jaws, cams and other
pinch points during operation.
24. When finished using the tool, insert the locking
pin to prevent foot pedal movement.
2
Familiarize yourself with the following safety notices used in this manual:
This means that if precautions are not heeded, it may result in minor injury and/or possible
machine damage.
This means that if precautions are not heeded, it may result in serious, or possibly even fatal,
injury.
SAVE THESE INSTRUCTIONS
2.0 About this manual
This manual is provided by JET, covering safe operation and maintenance procedures for a JET Model MSS-1
Manual Shrinker/Stretcher. This manual contains instructions on installation, safety precautions, general
operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and
constructed to provide consistent, long-term operation if used in accordance with the instructions as set forth in
this document.
If there are questions or comments, please contact your local supplier or JET. JET c an also be reached at our
web site: www.jettools.com.
Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.
Read and understand the entire contents of this manual before attempting assembly or
operation! Failure to comply may cause serious injury!
Register your product online -
http://www.jettools.com/us/en/service-and-support/warranty/registration/
3
3.0 Table of contents
Section Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2
2.0 About this manual .......................................................................................................................................... 3
3.0 Table of contents ............................................................................................................................................ 4
4.0 Specifications for Shrinker-Stretcher .............................................................................................................. 4
5.0 Setup and assembly ....................................................................................................................................... 5
5.1 Shipping contents ....................................................................................................................................... 5
5.2 Additional tools required ............................................................................................................................. 5
5.3 Assembly .................................................................................................................................................... 5
5.4 Installing jaw sets ....................................................................................................................................... 6
5.5 Locking pin ................................................................................................................................................. 6
6.0 Operation ....................................................................................................................................................... 7
6.1 General instructions and tips ...................................................................................................................... 7
6.2 General procedure for flange ..................................................................................................................... 7
7.0 User-maintenance .......................................................................................................................................... 7
7.1 Lubrication .................................................................................................................................................. 7
7.2 Additional servicing .................................................................................................................................... 7
8.0 Replacement Parts ......................................................................................................................................... 7
8.1.1 MSS-1 Shrinker/Stretcher – Exploded View ............................................................................................ 8
8.1.2 MSS-1 Shrinker/Stretcher – Parts List .................................................................................................... 9
9.0 Warranty and Service ................................................................................................................................... 10
4.0 Specifications for Shrinker-Stretcher
Model number .............................................................................................................................................. MSS-1
Stock number .............................................................................................................................................. 756018
Capacities:
Maximum thickness capacity, mild steel .................................................................................................... 16 ga.
Maximum thickness capacity, aluminum ................................................................................................... 18 ga.
Throat depth .............................................................................................................................. 6 in. (152.4 mm)
Throat height ............................................................................................................................. 2.5 in. (63.5 mm)
Maximum flange capacity ...................................................................................................... 1-1/8 in. (28.6 mm)
Main mate ri a l s :
Base ................................................................................................................................................... steel tubing
Wheels ....................................................................................................................................................... plastic
Stand ................................................................................................................................................... steel plate
Jaws ........................................................................................................................ hardened steel, HRC 40~45
Dimensions:
Overall dimensions, assembled (LxWxH) ................... 920 x 410 x 1175 mm (36-7/32 x 16-9/64 x 46-17/64 in.)
Shipping dimensions (LxWxH) .................................................... 118 x 50 x 21 mm (46-1/2 x 19-5/8 x 8-1/4 in.)
Weights:
Net weight (approx..) ........................................................................................................................... 38 kg (84 lb)
Shipping weight (approx..) ................................................................................................................ 50 kg (110 lb)
L= length; W=width; H=height
The specifications in this manual were current at time of publication, but because of our policy of continuous
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring
obligations.
4
Loading...