JET 728200 Operating Instructions and Parts Manual

JET

728200 Flip-Top Stand

Instructions and Parts List

IMPORTANT SAFETY INSTRUCTIONS

• Review all instructions before assembling the table. Improper assembly can cause personal injury and/or property damage.

• Do not exceed maximum load for the stand.

• Do not stand on this product.

• WARNING: This product can expose you to

chemicals including lead and cadmium which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca.gov.

Tools required for assembly

10mm and 16mm wrenches (a manual ratcheting socket wrench will speed assembly time)

Shipping contents

1 Table Assembly 4 Lower Braces (2 Long, 2 Short) 4 Vertical Legs 4 Adjustment Legs 4 Leveling Pads 1 Instructions and Parts List 1 Product Registration Card 1 Hardware Package (728200-HP)

44 Carriage Bolt M6-1.0x16 – AA 44 Flat Washer 6mm– BB 44 Lock Washers 6mm –CC 44 Hex Nut M6-1.0–DD

Assembly instructions

Use the exploded view and parts list as guides to assembly. Make all leg and brace fasteners only finger tight until the entire unit has been assembled.

1. Turn table assembly upside down; use a mat or piece of cardboard underneath to prevent scratching.

2. Assemble the four main legs (#20) to the table brackets (#8/26). Finger tighten only.

3. Determine the height desired, then connect the adjustment legs (#21) to the main legs. These can be repositioned later if needed. (It is recommended that each adjustment leg be secured by at least 4 screws to the main leg.)

4. Determine placement of lower braces (#24/25) and assemble them to the main legs/adjustment legs.

5. Install the leveling foot pads (#22) and tighten each hex nut (#23) against the adjustment leg. (If using the optional swivel casters, install those instead of the pads.)

6. Turn the unit over and push down lightly to make sure stand rests evenly upon the floor.

7. Fully tighten all fasteners. Take care to not overtighten.

Holes are provided in the lower braces for attaching a user-made shelf, not provided.

see page 4 for operating instructions

728200 Flip-Top Stand – Exploded View

To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

728200 Flip-Top Stand – Parts List

Index No. Part No. Description Size Qty

1 ................. TS-1541011 ................ Nylon Lock Hex Nut ..................................................... M5-0.8 ............................. 2

2 ................. 728200-002 ................. Flip-Top Table Locking Knob ....................................... ........................................ 2

3 ................. 728200-003 ................. Spring .......................................................................... ........................................ 2

4 ................. 728200-004 ................. Long Pin ....................................................................... ........................................ 2

6 ................ TS-1541041 ................ Nylon Lock Hex Nut ..................................................... M10-1.5 ........................... 2

7 ..................... TS-1550071 ................ Flat Washer .................................................................. 10mm .............................. 2

8 ......................728200-008 ................. Flip-Top Table Bracket (L) (#8-1 thru 8-3) ................... ........................................ 1

8-1 .................. .................................... Support Plate ............................................................... ........................................ 2

8-2 .................. .................................... Sleeve A....................................................................... ........................................ 2

8-3 .................. .................................... Sleeve B....................................................................... ........................................ 2

9 ..................... 728200-009 ................. Spring .......................................................................... ........................................ 2

10 ............... TS-1522021 ................ Socket Set Screw ........................................................ M5-0.8x8 ......................... 2

11 ................... 728200-011 ................. Pin ................................................................................ ........................................ 2

12 ................... 728200-012 ................. Flanged Hex Nut .......................................................... M6-1.0 ............................. 8

13 ............... 728200-013 ................. Flip-Top Table Connecting Plate (#13-1 thru 13-2) ...... ........................................ 2

13-1 ............ .................................... U Plate ......................................................................... ........................................ 2

13-2 ............ .................................... Shaft ............................................................................ ........................................ 2

14 ............... 728200-014 ................. Carriage Bolt ................................................................ M6-1.0x35 ....................... 8

15 ............... 728200-015 ................. Table (Plywood Top) .................................................... ........................................ 1

15.0 ............ 728200-015.0 .............. Table Assembly (#1 thru 15, #26) ................................ ........................................ 1

16 ...................728100-008 ................. Carriage Bolt ................................................................ M6-1.0x16 ..................... 44

17 ............... TS-1550041 ................ Flat Washer .................................................................. 6mm .............................. 44

18 ............... TS-2361061 ................ Lock Washer ................................................................ 6mm .............................. 44

19 ............... TS-2311061 ................ Hex Nut ........................................................................ M6-1.0 ........................... 44

20 .................. 728100-009 ................. Vertical Leg .................................................................. ........................................ 4

21 ............... 728100-010 ................. Adjustment Leg Weldment (#21-1 thru 21-3) ............... ........................................ 4

21-1 ............... .................................... Adjustment Leg ............................................................ ........................................ 4

21-2 ............... .................................... Plate ............................................................................. ........................................ 4

21-3 ............ .................................... Hex Nut ........................................................................ M10-1.5 ........................... 4

22 ................... 728100-012 ................. Bolt with Leveling Pad .................................................. M10-1.5 ........................... 4

23 .................... TS-2311101 ................ Hex Nut ........................................................................ M10-1.5 ........................... 4

24 .................... 728100-013 ................. Lower Brace Short ....................................................... ........................................ 2

25 .................... 728100-014 ................. Lower Brace Long ........................................................ ........................................ 2

26 ...................728200-026 ................. Flip-Top Table Bracket (R) (#8-1 thru 8-3) ................... ........................................ 1

27 ............... 728100-015 ................. JET Logo with Adhesive ............................................. 4.75”x3.3” ........................ 1

................... 728200-030 ................. ID Label 728200 (not shown) ....................................... ........................................ 1

................... 728200-031 ................. Flip-Top Stand Decal (not shown) ................................ ........................................ 1

................... 728200-HP .................. Hardware Package (#16 thru 19) ................................. ........................................ 1

Optional Accessory* – Swivel Caster

28 ............... 98-0129 ....................... Swivel Casters (set of 4) .............................................. .................................. 1 set

* Optional Accessory – see your dealer to order.

Operation

CAUTION: If the optional casters are used, make sure they are locked in place.

To tilt table:

1. Pull out left and right handles and rotate them 90degrees to keep them disengaged.

2. Begin tilting front edge of table downward until it just clears the handle pins, then turn handles 90degrees and allow them to slide back in.

3. Continue to tilt table slowly, while helping stabilize the machine(s), until table passes the beveled pins at the rear and snaps into level position.

When machines are

mounted to table, tilt table slowly and help stabilize the machines throughout the tilt process. Do not allow the table to swing uncontrollably. Failure to comply may cause personal injury and/or unnecessary stress upon stand components.

Machine selection

The stand will accept most bench top machines up to load capacity and within the table size range (see specifications). Secure the machine to the table with appropriate fasteners (not provided). Make sure machine(s) are securely fastened before attempting to tilt the table.

Position of machines upon the table is user’s choice; however, consideration should always be given to the machines’ center of balance and weight distribution. Ideally, they are centered upon the table. But the design of some machines may require them to be shifted off center for optimum position and/or easier tilting to the down position.

(machines and user-made shelf not provided)

Specifications for JET Flip-Top Stand

Stock number

728200

Table size (D x W)

20 x 25 in. (508 x 635 mm)

Height range

29 to 34 in. (736.6 to 863.6 mm)

Height adjustment

5.10 in. (130 mm)

Load capacity

300 lb. (136 kg)

Table material

MDF/Vinyl

Assembled weight

45 lb. (20 kg)

Shipping weight

49 lb. (22 kg)

The 728200 Flip-Top Stand will accommodate most bench top machines, including the following models:

Brand

Model

Stock No.

Notes

JET

13” Planer

722130

JET

8” Jointer/Planer

707400

JET

8” Grinder

726101

JET

1020 Drum Sander

723510

JET

9” Belt/Disc Sander

708595

JET

Spindle Sander 5”

708404

JET

18” Scroll Saw

727300B

JET

22” Scroll Saw

727200B

JET

10” Miter Saw

707210

Secure miter arm before tilting underneath.

JET

12” Miter Saw

707212

Secure miter arm before tilting underneath.

JET

JET Mortiser

708580

Remove handle if needed before tilting underneath.

Powermatic

PM Mortiser

1791310

Remove handle if needed before tilting underneath.

JET

10” Band saw

714400

JET

12” Drill Press

716000

JET

15” Drill Press

716200

Powermatic

PM1250 Air Filtration

1791250