Assembly Instructions and Parts List
Stand for JWL-1221VS Lathes
Stock No. 719202A
Read and understand the entire
owner's manual that accompanied your JWL1221VS lathe before attempting assembly or
operation of accessories.
WARNING: This product can expose you to
chemicals including lead and cadmium which are
known to the State of California to cause cancer and
birth defects or other reproductive harm. For more
information go to http://www.p65warnings.ca.gov.
WARNING: Drilling, sawing, sanding or
machining wood products generates wood dust and
other substances known to the State of California to
cause cancer. Avoid inhaling dust generated from
wood products or use a dust mask or other
safeguards for personal protection.
Wood products emit chemicals known to the State
of California to cause birth defects or other
reproductive harm. For more information go to
http://www.p65warnings.ca.gov/wood.
Inspect contents for shipping damage. Report any
damage or part shortages to your distributor. Do not
discard shipping materials until accessory is set up
and functioning properly.
Assembly
Refer to exploded view on reverse side for parts
clarification. Bracketed numbers refer to index
numbers in exploded view.
1. Install two levelers [5] into bottom of each leg.
Levelers can be adjusted for height and leveling
of lathe. Tighten hex nut [6] against leg to
secure setting.
2. Install cross bar [4] to bottom of legs with
screws and washers [7/8]. Make snug but do
not fully tighten yet.
3. Install tool tray [13] with screws, nuts and
washers [8/9/17]. Do not fully tighten yet.
4. Mount a bracket [1] to each leg with screws,
washers, and nuts [7/8/9]. Gussets on brackets
should face toward each other. Multiple holes
allow adjustment of lathe height. Make nuts
snug but do not fully tighten yet.
5. Place lathe onto stand brackets, and secure
with screws and washers [10/11/12]. Insert all
four screws first, then tighten each securely.
6. Fully tighten all screws and nuts in cross bar [4],
tool tray [13] and brackets [1].
Shipping contents
1 Cross bar
2 Legs
2 Brackets
4 Tube caps
4 Levelers with hex nut
1 Tool tray
1 Hardware package, includes:
4 Socket head cap screws, 5/16x3/4
4 Lock washers, 5/16
4 Flat washers, 5/16
8 Socket head cap screws, M8x80
4 Socket head cap screws, M8x75
20 Flat washers, 8mm
4 Hex nuts, M8
Tools required for assembly
6mm hex key (“Allen wrench”)
Open-end wrenches, 13mm (1/2"); 14mm (9/16”)
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Manual No. M-719202A
Ph.: 800-274-6848 Edition 3 09/2019
www.jettools.com Copyright © 2017 JET, a Division of JPW Industries, Inc.
Specifications
Stock no. 719202A
Assembled dimensions (WxDxH) approx. 788 x 584 x 800 mm (31 x 23 x 31-1/2 in.)
Height positions: 28-3/4, 29-3/4, 30-3/4, 32-1/2 in.
Shipping dimensions (WxDxH) approx. 810 x 700 x 220mm (31.9 x 27.6 x 8.7 in.)
Net weight (approx.) 18 kg (40 lbs)
Shipping weight (approx.) 21.5kg (47.3 lbs)
# 719202A Stand for JWL-1221VS Lathes
Index No Part No Description Size Qty
1 ................. JWL1221VSS-101 ....... Bracket ......................................................................... ........................................ 2
2 ................. JWL1221VSS-102 ....... Steel Leg ...................................................................... ........................................ 2
3 ................. JWL1221VSS-103 ....... Cover ........................................................................... ........................................ 4
4 ................. JWL1221VSS-104 ....... Cross Bar ..................................................................... ........................................ 1
5 ................. JWL1642-206 ............ Leveler ......................................................................... 3/8” .................................. 4
6 .................
7 ................. F005415 ...................... Hex Socket Hd Cap Screw * ........................................ M8-1.25 x 80 ................... 8
8 ................. TS-1550061 ................ Flat Washer * ............................................................... M8 ................................. 20
9 ................. TS-1540061 ................ Hex Nut *...................................................................... M8 ................................... 8
10 ............... TS-0680031 ................ Flat Washer * ............................................................... 5/16” ................................ 4
11 ............... TS-0720081 ................ Lock Washer * .............................................................. 5/16” ................................ 4
12 ............... TS-0208041 ................ Socket Head Cap Screw *............................................ 5/16”-18 x 3/4” ................. 4
13 ............... JWL1221VS-407 ......... Tool Tray ...................................................................... ........................................ 1
14 ............... JWL1221VS-409 ......... Tool Tray Cover ........................................................... ........................................ 1
15 ............... JWL1221VS-411A ....... Plate ............................................................................. ........................................ 1
16 ............... JWL1221VS-410 ......... Machine Tapping Screw .............................................. 3.5 x 10 mm .................. 10
17 ............... TS-2238751 ................ Hex Socket Hd Cap Screw * ........................................ M8-1.25 x 75 ................... 4
................... LM000288 ................... ID Label (not shown) .................................................... ........................................ 1
................... JWL1221VSS-HP ........ Hardware Package (includes items with *) ................... ..........................................
TS-0561031 ............... Hex Nut ........................................................................ 3/8”-16 ............................. 4
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00
p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to
serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually.
Loading...