JET 719201 Operating Instructions and Parts Manual
Assembly Instructions and Parts List
22-1/2” Bed Extension for JWL-1221VS Lathe
Stock No. 719201
Read and understand the entire owner's manual that accompanied your JWL-1221VS
lathe before attempting assembly or operation of accessories.
WARNING: This product can expose you to chemicals including lead and cadmium which are known to the
State of California to cause cancer and birth defects or other reproductive harm. For more information go to
http://www.p65warnings.ca.gov.
WARNING: Drilling, sawing, sanding or machining wood products generates wood dust and other
substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood
products or use a dust mask or other safeguards for personal protection.
Wood products emit chemicals known to the State of California to cause birth defects or other reproductive
harm. For more information go to http://www.p65warnings.ca.gov/wood.
Inspect contents for shipping damage. Report any
damage or part shortages to your distributor. Do
not discard shipping materials until accessory is set
up and functioning properly.
Shipping contents
1 Bed extension
2 Socket head screws, 5/16x1
2 Lock washers, 5/16x1
2 Flat washers, 5/16x1
1 Positioning plate
1 Pan head screw, 1/4x1/2
Tools required for assembly
6mm hex key (“Allen wrench”)
Cross point screwdriver
Assembly
(Parts in brackets refer to index numbers in the
exploded view.)
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-719201
Ph.: 800-274-6848 Revision A2 11/2018
www.jettools.com Copyright © 2014 JET
1. Use the pan head screw [1] to attach plate [2]
to end of bed extension [3] where the beds will
meet.
2. Place bed extension against lathe bed and
hold in place with the plate [2].
3. Insert two socket head screws [6], lock
washers [5] and flat washers [4]. Align beds as
closely as possible, then snug the screws but
do not fully tighten yet.
4. Move tailstock over the seam of lathe bed and
bed extension and align the clamping nut in
the center where the beds meet. (Shift bed
extension as needed until tailstock can slide
onto it). Tighten tailstock clamping lever – this
will properly align and make flush the beds.
5. Tighten both socket head screws [6].
6. Unlock tailstock, and slide it back and forth
across seam to verify smooth travel.
Specifications
Stock number .............................................................................................................................................. 719201
Assembled dimensions ...................................................................... 572 x 229 x 216 mm (22.5”L x 9”W x 8.5”H)
Net weight ...................................................................................................................................... 19 kg (41.89 lb)
Shipping dimensions ..................................................................... 640 x 288 x 277 mm (25.20” x 11.33” x 10.90”)
Shipping weight ................................................................................................................................ 22 kg (48.5 lb)
Specifications were current at time of publication, but because of our policy of continuous improvement, JET
reserves the right to change specifications at any time and without prior notice, without incurring obligations.
# 719201 Bed extension (22-1/2”) for JWL-1221VS lathe
Index No Part No Description Size Qty
1 ................. TS-081F032 ................ Phillips Pan Head Machine Screw ............................... 1/4”-20x1/2” ..................... 1
2 ................. JWL1221VS-502 ......... Plate ............................................................................. ........................................ 1
3 ................. JWL1221VS-503 ......... Extension Bed .............................................................. ........................................ 1
4 ................. TS-0680031 ................ Flat Washer .................................................................. 5/16” ................................ 2
5 ................. TS-0720081 ................ Lock Washer ................................................................ 5/16” ................................ 2
6 ................. TS-0208061 ................ Socket Head Cap Screw .............................................. 5/16”-18x1” ...................... 2
To order parts or reach our service department, call 1-800-274-6848 Monday through Friday, 8:00 a.m. to 5:00
p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us
to serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Loading...