JET 414502, 414500 User Manual

This .pdf document is bookmarked

Operating Instructions and Parts Manual

14-inch Vertical Band Saws

Models: J-8201, J-8203, J-8201VS, J-8203VS

JET

Warranty and Service

JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.

Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website.

• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the date of receipt.

• Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Co vered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of maintenance.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initia l p u rch a s e whe n calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET website.

More Informa tion

JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET website.

How S tate Law A pplies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET

Product Listing with Warranty Period

90 Days – Parts; Consumable items; Light-Duty Air Tools 1 Year – Motors; Machine Accessories; Heavy-Duty Air Tools; Pro-Duty Air Tools 2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used for industrial or commercial purposes 5 Year – Woodworking Machinery Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools

NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.

branded products are not sold in Canada by JPW Industries, Inc.

Section Page

Warranty and Service ............................................................................................................................................ 2

Table of contents ................................................................................................................................................... 3

Warning ................................................................................................................................................................. 4

Machinery General Safety Warnings .................................................................................................................... 4

General Electrical Cautions ................................................................................................................................... 5

Switch Padlock ...................................................................................................................................................... 5

Safety Instructions for Sawing Sys tems ................................................................................................................ 6

Specifications ........................................................................................................................................................ 7

Introduction ........................................................................................................................................................... 8

Band Saw Features ............................................................................................................................................... 8

Setup and Operation ............................................................................................................................................. 8

Set-up ................................................................................................................................................................ 8

Electrical ................................................................................................................................................................ 9

Connecting to 3-phase power ........................................................................................................................... 9

GROUNDING INSTRUCTIONS ........................................................................................................................ 9

Installing Optional Frame Riser ....................................................................................................................... 12

Installing Optional Rip Fence ................................................................................................. ......................... 12

Operating Controls .............................................................................................................................................. 13

START/STOP Switch ...................................................................................................................................... 13

Variable Speed Control ................................................................................................................................... 13

Operating Instructions ......................................................................................................................................... 13

Saw blades ...................................................................................................................................................... 13

Adjustments ........................................................................................................................................................ 14

Adjusting Blade Support/Guide Height ............................................................................................................ 14

Adjusting Blade Tension .................................................................................................................................. 14

Adjusting Table Angle ..................................................................................................................................... 14

Leveling Work Table ........................................................................................................................................ 14

Adjusting Miter Gauge Slot Parallelism ........................................................................................................... 15

Adjusting Blade Speed (Models J-8201/J-8203) ............................................................................................. 15

Adjusting Blade Speed (Models J-8201VS/J-8203VS) ................................................................................... 15

Changing Clutch Position ................................................................................................................................ 15

Changing Drive Belt Position ........................................................................................................................... 16

Changing Pulley-to-Belt Posi tion ..................................................................................................................... 16

Using Miter System ......................................................................................................................................... 17

Using Rip Fence .............................................................................................................................................. 17

Using the Dust Control Chute .......................................................................................................................... 17

Maintenance ........................................................................................................................................................ 17

Changing Saw Blade ....................................................................................................................................... 17

Replacing drive wheel rubber protectors ......................................................................................................... 19

Draining and refilling the reduction gearbox .................................................................................................... 19

Periodic Maintenance .......................................................................................................................................... 19

Troubleshooting .................................................................................................................................................. 19

Periodic Maintenance .......................................................................................................................................... 20

Troubleshooting the J-8201/8203/8201VS/8203VS ............................................................................................ 21

Replacement Parts .............................................................................................................................................. 22

Exploded View and Parts List – Base – Models J-8201 and J-8203 ............................................................... 23

Exploded View and Parts List – Base – Models J-8201VS and J-8203VS ..................................................... 24

Exploded View – Saw Head – Models J-8201,J-8203,J-8201VS and J-8203VS ............................................ 25

Parts List – Saw Head – Models J-8201,J-8203,J-8201VS and J-8203VS ..................................................... 26

Exploded View – Gearbox – Models J-8201 and J-8203 ................................................................................ 28

Parts List – Gearbox – Models J-8201 and J-8203 ......................................................................................... 29

Exploded View – Gearbox – Models J-8201VS and J-8203VS ....................................................................... 30

Parts List – Gearbox – Models J-8201VS and J-8203VS ............................................................................... 31

Exploded View and Parts List – 5782181 Optional Riser Block – All Models ................................................. 32

Rip Fence Assembly (Optional Equipment) .................................................................................................... 33

Electrical Connections ......................................................................................................................................... 34

Warning

- Misuse of this machine can cause serious

injury.

- For safet y, m ac hine must be set up, used and

serviced pr operl y .

- Read, understand and follow instructions in

the Operating Instructions and Parts Manual which was shipped with your m ac hine.

When setting up machine:

- Always avoid using machine in damp or

poorly li ghted work areas.

- Always be sure the machine support is

securely anchored to the floor or the work bench.

When using machine:

- Alwa ys wear saf ety glasse s with sid e shields

(See ANSI Z87.1)

- Never wear loose cl othing or jewelry.

- Never overr eac h—you may sli p and fall.

When servicing machine:

- Always disconnect the machine from its electric al suppl y while servicing.

- Always follow instructions in Operating Instructi ons and Parts Manual when changi ng accessory tool s or parts.

- Never modif y the machine without consulting JET Tools .

You—the stationary power tool user—hold the key to safety.

Read and follow these simple rules for best results and full benefits from your machine. Used properly, JET machinery is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use t hem correc tly. T hey should read and understand the Operating Instructions and Parts Manual as well as all labels affixed to the machine. Failure in following all of th ese warnings can cause serious injuries.

Machinery General Safety Warnings

1. KEEP GUARDS IN PLACE and in working order.

2. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.

3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted.

5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from work area.

6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.

7. DON’ T FORCE TOOL It will do the job better and safer at the rate for which it was designed.

8. USE RIGHT TOOL Don’t force tool or attachment to do a job for which it was not designed.

9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An under-sized cord will cause a drop in line voltage resulting in loss of

power and overheating. Table 1 shows the correct size to use depending on cord length and name-plate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.

10. WEAR PROPER APPAREL Do not wear loose clot hing, g loves, neckties, rings, bracelets, or othe r je welr y whic h ma y get caug ht i n movi ng parts. Non-slip footwear is recommended. Wear protective ha ir covering to contain lo ng hair.

11. WEAR EYE PROTECTION. Always use safety glasse s. A lso u se fac e or d ust m ask if cutt ing operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.

13. DON’T OVERREACH. Keep proper footing and balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.

15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL STA RT ING. Ma ke sur e sw it ch i s in of f po sit ion before plugging in.

17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recomm ended accessories. The use of improper accessories may cause risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be properly repaired or replaced.

20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction of rotation of the blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.

22. DO NOT REMOVE JAMMED CUTOFF PIECES until the blade has stopped.

23. MAINTAIN PROPER ADJUSTMENT of blade tension, blade guides and thrust bearings.

24. ADJUST UPPER BLADE GUIDE TO JUST CLEARWORKPIECE.

25. HOLD WORKPIECE FIRMLY AGAINST TABLE.

General Electrical Cautions

This saw should be grounded in accordance with the National Electrical Code and local codes and ordi nances. This work should be done by a qualified electrician. The saw should be grounded to protect the user from electrical shock.

Caution: For circuits which are f ar away from the electrical service box, the wire size must be increased in order to deliver ample voltage to the motor. To minimize power lo sses and to prevent motor o verheating and burnout, the use of wire sizes for branch circuits or electrical extension cords according to the f ollowing table is recommended.

Volts Total length of cord in feet

120 V

Ampere Rating

More than Not more than AWG minimum gage

0 6

6 10 10 12 12 16 14 12 Not recommended

Only the applicable parts of the Table need to be included. For instance, a 120-volt product need not include the 240-volt heading.

240 V 50 ft. 100 ft. 200 ft. 300 ft.

25 ft. 50 ft. 100 ft.

18 16 16 18 16 14 16 16 14

150 ft.

14 12 12

Swi t c h Padlock

To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock (not provided) is highly recommended.

To lock the main switch in the OFF position, remove the sw itch key f rom the swit ch. Place the key in a location that is inaccessible to children and others not qualified to use the tool.

1. Open the padlock (Fig. A).

2. Insert through holes in the start button (Fig. B).

3. Close the padlock.

For three phase tools without the lock-off feature, observe the following instruction: The installer shall follow local regulations and National Electrical Code, ANSI/NFPA 70 installation requirements.

4. Place the key in a saf e place and out of reac h of children.

Safety Instructions for Sawing Systems

1. Always wear leather gloves when handling saw blade. The operator shall not wear gloves when operating the machine.

2. All doors shall be closed, a ll panels replaced, and other safety guards in place prior to the machine being started or operated.

3. Be sure that the blade is not in contact with the workpiece when the motor is started. The motor shall be started and you should allow the saw to come up to full speed before bringing the saw blade into contact with the workpiece.

4. Keep hands away from the blade area. See Figure A.

5. Remove any cut off piece carefully while keeping your hands free of the blade area.

6. Saw must be stopped and electrical supply must be cut off before any blade replacement or adjustment of blade support mechanism is done, or before any attempt is made to change the drive belts or before any periodic service or maintenance is performed on the saw.7.

7. Remove loose items and unnecessary workpieces from area before starting machine.

8. Bring adjustable saw guides and guards as close as possible to the workpiece.

9. Always wear protective eye wear when operating, servicing, or adjusting machinery. Eyewear shall be impact resistant, protective safety glasses with side shields complying with ANSIZ87.1 specifications. Use of eye wear which does not comply with ANSI Z87.1 specifications could result in severe injury from breakage of eye protection. See Fi gure B.

10. Nonslip footwear and safety shoes are recommended. See Figure C.

11. Wear ear protectors (plugs or muffs) during extended periods of operation. See Figure D.

12. The workpiece, or part being sawed, must be securely clamped before the saw blade enters the workpiece.

13. Remove cut off pieces carefully, keeping hands away from saw blade.

14. Saw must be stopped and electrical supply cutoff or machine unplugged before reaching into cutting area.

15. Avoid contact wit h coolant, especiall y guarding your eyes .

Specifications

JET’s 14-inch Vertical Band Saws are specially designed to effectively cut a variety of materials including wood, plastic, bakelite, composites, ferrous and non-ferrous metals. Models J-8201 and J-8203 are wood and metal cutting band saws. JET’s Model J-8201VS and J-8203VS 14-inch Variable Speed Band Saws are ideally suited for metal cutting only wit h an infinitely variable speed ra nge from116 to 334 SFP M. The variable speed drive system allows the operator to fine-tune the blade speed to the material being cut to maximize the life of today’s bi-metal blades. These versatile a nd dependable saws are capable of contour c utting, straight cutti ng and resawing, and these band saws can cut delicate curves in thick or thin stock.

Model number ...........................................J-8201K ..................... J-8203K ................. J-8201VS ................ J-8203VS

Stock number ............................................. 414500 ....................414504C .................... 414502 .................... 414503

Capacities:

Under Guide (in.) ............................................ 6 .............................. 6 .............................. 6 ............................. 6

Under Guide with Riser Block (in.) ................. 12 ..............................12 ............................ 12 ........................... 12

Throat Capacity (in.) ................................... 13.5 ........................... 13.5 ......................... 13.5 ........................ 13.5

Blade Wid th Capacity (in.) ................... 1/8 to 3/4 ................... 1/8 to 3 /4 ..................1/8 to 3/4 ................. 1/8 to 3/4

Motor:

Rating ................................................ 1HP 1PH ................... 1HP 3PH ..................1HP 1PH ................. 1HP 3PH

Voltage ......................................... 115/230 VAC ............. 230/460 VAC ........... 115/230 VAC ........... 230/460 VAC

(Prewired 115 V ) ...... (Prewired 23 0 V ) ....... (Prewire d 115V) ...... (Prewired 230V)

Listed Full Load Amps ............................ 10/5 A .................... 3.6/1.8 A ...................... 10/5 A ................. 3.6/1.8 A

Speed .............................................. 1725 RPM ................. 1725 RPM ................ 1725 RPM ............... 1725 RPM

Cutting Speeds:

Wood (SFPM) ............................................ 3300 .......................... 3300 ........................ 2600 ........................2600

Metal (SF PM ) ............................... 39 ,57 ,78 ,1 07 .............39,57 ,78 ,1 07 , ..................... 90 -340 ............ ........ 90-3 4 0

142,196,278 .............. 142,196,278 ......... Va ria ble spe e d ........ Va ria ble spe e d

Table:

Size (in.) ................................................ 14 x 14 ...................... 14 x 14 .....................14 x 14 .................... 14 x 14

He ig h t from F loor (in .) ................................... 44 ..............................44 ............................ 44 ........................... 4 4

Tilt to Right ............................................ 45 deg. ...................... 45 deg. .................... 45 deg. .................... 45 deg.

Tilt to Left .............................................. 15 deg. ...................... 15 deg. .................... 15 deg. .................... 15 deg.

Miter Gauge Groove (WxD/in.) ............. 3/4 x 3/8 .................... 3/4 x 3/8 ................... 3/4 x 3/8 .................. 3/4 x 3/8

Miter Ga uge.............................................. standard .................... standard .................. standard .................. standard

Noise emission (tested @3ft from machine):

Idle .......................................................... 70 dB ........................ 70 dB ....................... 70 dB ...................... 70 dB

With load ................................................. 75 dB ........................ 75 dB ....................... 75 dB ...................... 7 5 dB

Blade Dimensions (in.) ................ 3/8 x 0.025 x 93.5 ...... 3/8 x 0.025 x 93.5 ..... 3/8 x 0.025 x 93.5 .... 3/8 x 0.025 x 93.5

Floor Space Required (LxWxH/in.) ..... 26x18-1/2x67 ............. 26x18-1/2x67 ........... 26x18-1/2x67 .......... 26x18-1/2x67

Net Weight (lb)..................................................171 ............................ 155 .......................... 325 ......................... 325

The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring obligations.

Introduction

This manual includes operating and maintenance instructions for the JET 14-Inch Vertical Band Saws, Models J-8201, J-8203, J-8201VS, and J8203VS. This manual also includes parts listings and illustrations of replaceable parts.

Band Saw Features

Refer to Figures 1 through 3 for k ey features of the band saw. Refer to the Specifications section for additional information on the features and capabilities of the saw.

Figure 3: Band Saw Features – Front View (All Models

Setup and Operation

Figure 1: Band Saw Features - Rear View (Models J-8201/J-8203)

Figure 2: Band Saw Features – Rear View (Models J-8201VS/J-8203VS)

Set-up

1. The saw should be bolted securely to the shop floor to make sure the saw is stable when sawing long, heavy or unwieldy work pieces. Always use extra support for long or heavy stock. There are lugs in the bottom of the saw base for use in bolti ng down of the saw. A fter positioning the saw, open the door i n the base and mark the positions of the four lug holes. Move the saw to expo se the marks. Prepare for attachment as required by the attachment method being used. Install the applicable fast ener s. Inst a ll s him s as r eq uir ed t o le vel t he saw. T ighten t he fa steners to secure the saw to the floor.

2. Check belt tension (refer to Changing Drive Belt Position).

3. Check gearbox fluid level in sight gauge. If required, add lubricant to bring level halfway up the sight gauge. (Two containers of Shell Spirax 90 HD gear oil are packed with the saw. The containers have sufficient amount of lubricant to fill the gearbox.)

4. Check blade tension and support mechanism adjustment (refer to Changing Saw Blades).

5. Connect power to the saw. For 3-phase motors, follow the instructions in the Electrical section to complete the electrical hookup.

NOTE: Observe all electrical codes. Local codes or difficult environmental conditions may demand special electrical hook-ups. Always use a licensed electrician for any special electrical hook-up.

Electrical

Models J-8201 and J-8201VS are de livered with a 115 volt single phase motor. Models J-8203 and J8203VS are delivered with a 220/440 volt, 3-phase motor.

When the saw is a 115 volt model, it is supplied with a standard 115 volt plug and power cord which can be plugged into any suitable branch circuit.

When the saw is equipped with a 3-phase motor there will be no plug on the 4-wire cable to the saw switchbox. Instead, follow these instructions to connect the 3-phase motor to the power source:

Connecting to 3-phase power

1. Disconnect and lock out the branch circuit to the saw before attempting electrical connections.

2. Connect the green or green-with-white-trace wire to the branch circuit ground wire.

3. Connect the remaining three wires to the power wires in the 3-phase branch circuit.

4. Reestablish power in the electrical branch.

5. Turn on power to the saw motor using the switch.

6. Observe the direction of the blade. It should be going DOWNWARD, into the slot on the table. If it is not going downward, the power wires are hooked-up incorrectly.

7. To correct hook-up, disconnect and lock out power to the branch, again. Reverse any two of the power wires on the hook-up to the saw cable.

8. Reestablish power i n the branch and tur n the saw on again. The blade should now be going downward into the table slot.

Note: local electrical codes or ot her codes may require direct connection to a covered, protected junction box, or other electrical hook-up method. Especially under difficult industrial conditions, specialized electrical connections may be necessary. For special electrical hook-ups, a licensed electrician should be used to connect the saw to power.

CAUTION: KNOW AND OBSERVE ALL LOCAL AND OTHER APPROPRIATE ELECTRICAL CODES WHEN ATTACHING THIS BAND SAW TO YOUR POWER SUPPLY.

Figure 4: Wiring Diagrams

GROUNDING INSTRUCTIONS

1. All grounded, cord-connected tools:

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce t he risk of electr ic shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ord i nances.

Do not modify the plug provided - if it will not fit the outlet; have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The cond uctor with insulation having an outer surf ace that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Use only 3-wire extension cords that have 3pronggrounding plugs and 3-pole receptacles that accept the tool’s plug.

Repair or replace damaged or worn cord immediately.

2. Grounded, cord-connected tools intended for

use on a supply circuit having a nominal rating less than 150 volts:

This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Sketch A. The tool has a grounding plug that looks like the plug illustrated in Figure 5-A. A temporary adapter, which looks like the adapter illustrated in Figure 5B and C, may be used to connect this plug to a 2pole receptacle as shown in Sketch B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. (This adapter is not permitted in Canada.) The green-co lored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.

3. Grounded, cord-connected tools intended for

use on a supply circuit having a nominal rating between 150 – 250 volts, inclusive:

This tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Figure 5A. The tool has a grounding plug that looks like the plug illustrated in Sketch A. Make sure the tool i s connected to an outlet having the same configuration as the plug. No adapter is available or should be used with this tool. If the tool must be reconnected for use on a diff erent type of electric circuit, the reconnection should be made by qualified service personnel; and after reconnection, the tool should comply with all local codes and ordinances.

4. Permanently connected tools:

This tool should be connected to a g ro unded metal per mane nt wir i ng syst em; or to a sy stem hav i ng an equipment-grounding conductor.

Figure 5: Grounding methods

+ 25 hidden pages