Jensen XS525, XS650, XS6090, XS5768 Installation Manual

Speaker Installation Manual

XS525 / XS650 / XS5768 / XS6090

INTRODUCTION

Thank you for purchasing this quality Jensen product! Your
new Jensen speaker system is the ultimate complement to your
car stereo system. Jensen speakers feature injection molded
mica-reinforced polypropylene cones, nitrile rubber surrounds,
optimized magnet systems and silk dome tweeters with
neodymium magnets for unparalleled audio reproduction and
outstanding durability.

The speaker system should be connected to your car radio or
an additional car stereo amplifier, which we recommend for
even better sound quality. Technical data plus installation tips
and further advice are contained in this instruction manual.

Highlighted Features

!

!

!

!

!

!

Black warp-resistant, low-resonance steel basket
Low distortion mica-reinforced injection molded
polypropylene woofer cones for smooth frequency response
and great weather resistance
Nitrile rubber surrounds for excellent damping
Nomex-reinforced spiders for excellent linearity
Silk dome tweeters provide smooth, crisp high frequencies
Optimized magnet systems provide outstanding bass
performance
Metal mesh grilles included on all models except 5x7/6x8.

1

Para obtener instrucciones en Español, diríjase a la página 7.
Pour des instructions en Francais, référez-vous à la page 13.

!

Preparation

! Disconnect battery cable from negative ( - ) battery terminal.

WARNING: Check vehicle's owner's manual before
disconnecting the battery. Disconnecting the battery in
some vehicles may require an anti-theft code when
reconnecting. Some vehicles may run rough after
reconnecting the battery and require that the on-board
computer be reset at the dealership. Check with your local
dealer if you are uncertain.

! Check all safety regulations in your vehicle's owner's manual.
! To ensure an obstacle-free fit, check and double check

mounting depth of the speakers against available depth, as
well as the location of window mechanics, door handles, and
window handles.

! If using provided grilles, be sure mounting location is sufficient

distance from door and/or window handles.

Since some of these Jensen full range speakers are most often
used as direct replacements for stock speakers, some of the
following instructions will not apply. For custom installations see
your authorized Jensen dealer.

If, after reading your manual, you still have questions regarding
this product, we recommend that you see your Jensen dealer. If
you need further assistance, you can call us direct at
1-888-921-4088. Be sure to have your model number and date

of purchase available when you call. Please read your warranty
clearly and retain your receipt for possible future use.

Speakers

Basic Installation Steps

Step 1: Remove existing speaker.
Step 2: Position new speaker and align with existing mounting

holes.

Step 3: Attach the positive (+) and negative (-) speaker terminals

(see FIGURE 2). Be sure to observe proper polarity when
connecting the wires (the striped wire is the negative
lead).

Step 4: If not using factory grilles, attach grille.
Step 5: Mount speaker (using factory hardware when possible).
Step 6: Reconnect negative battery terminal.

INSTALLATION

FIGURE 2 - CONNECTING SPEAKER WIRES

FIGURE 3 - REAR DECK INSTALLATION

FIGURE 1 - DOOR PANEL INSTALLATION

Speaker

Door Panel

2

Grille

Speakers

3

SPECIFICATIONS

Woofer Diameter

Frequency Response

Power Handling

Woofer Cone Material

Woofer Surround Material

Tweeter Driver(s)

Sensitivity (1W/1M) Magnet

Weight

Xmax

Impedance

Mounting Depth Mounting

Cutout

Grille Height

Tweeter Height

XS5768

5"x7" / 6"x8"

42Hz - 30kHz (-3dB)

70 Watts RMS

280 Watts Peak

Mica Impregnated Injection

Molded Polypropylene

Nitrile Butadiene Rubber

25mm Silk Dome Tweeter

92dB

13 oz

3.4mm

4 Ohm

2.20" (56mm)

5.05" x 7.1" (128 x 181mm)

1.0" (25.5mm)

0.65" (16.5mm)

XS6090

6"x9"

32Hz - 35kHz (-3dB)

100 Watts RMS

400 Watts Peak

Mica Impregnated Injection Molded

Polypropylene

Nitrile Butadiene Rubber

25mm Silk Dome Tweeter

13mm Silk Dome Tweeter

91dB

20 oz

4.5mm

4 Ohm

3.35" (85mm)

5.9" x 8.58" (150 x 218mm)

1.15" (29mm)

0.45" (11mm)

XS525

5.25"

45Hz - 35kHz (-3dB)

60 Watts RMS

240 Watts Peak

Mica Impregnated Injection

Molded Polypropylene

Nitrile Butadiene Rubber

20mm Silk Dome Tweeter

90dB

10 oz

3.0mm

4 Ohm

2.0" (51.5mm)

4.45" (113mm)

0.87" (22mm)

0.67" (17mm)

XS650

6.5"

42Hz - 30kHz (-3dB)

70 Watts RMS

280 Watts Peak

Mica Impregnated Injection

Molded Polypropylene

Nitrile Butadiene Rubber

25mm Silk Dome Tweeter

91dB

13 oz

3.4mm

4 Ohm

2.05" (52mm)

5.05" (128mm)

1.06" (27mm)

0.88" (22.5mm)

Speakers