BLUETOOTH ALL-IN-ONE HI-FI MUSIC SYSTEM
WITH PA
MODEL : SMPS-750
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS
UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
1
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE
FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR
SHOCK
he Caution Marking is located at the back enclosure of the apparatus.
T
The Rating plate is located at the back enclosure of the apparatus
HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that product heat.
9. AC adapter is used as disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the mains completely, the AC
adapter should be disconnected form the mains socket outlet completely.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with a cart, stand, tripod, bracket, or table recommended by
the manufacturer, or sold with the product. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from
tip-over.
12. Unplug this apparatus during lightning storms or when unused for a long
periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
14. This appliance shall not be exposed to dripping or splashing water and that no object filled
with liquids such as vases shall be placed on the apparatus.
15. Do not overload wall outlet. Use only power source as indicated.
E-
2
16. Use replacement part as specified by the manufacturer.
17. Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks.
18. Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to your
home, consult your product dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instruction.
19. Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on the product.
20. Damage Requiring Service - Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls may result in damage and will often require
extensive work by a qualified technician to restore the product to its normal operation.
If the product has been dropped or damaged in any way, and
e) When the product exhibits a distinct change in performance - this indicates a need
for service.
21. Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
22. Excessive sound pressure from earphones and headphone can cause hearing loss
23. Minimum distances of 10 cm around the apparatus for sufficient ventilation.
24. The ventilation should not be impeded by covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
25. No naked flame sources, such as lighted candles, should be placed on the apparatus.
26. The use of apparatus in moderate climates.
27. Attention should be drawn to the environmental aspects of battery disposal.
SAVE THESE INSTRUCTIONS
E-
3
COMPLIANCE WITH FCC REGULATIONS
FCC ID : RSBSMPS-750
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly appr
responsible for compliance could void the user’s authority to operate
the equipment.
oved by the party
PRECAUTIONS BEFORE USE
• DO NOT CONNECT THE AC ADAPTER TO THE MAINS BEFORE CHECKING THE
MAINS VOLTAGE AND UNTIL ALL OTHER CONNECTIONS HAVE BEEN MADE.
• DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF
SEVERAL INCHES AROUND THE UNIT FOR VENTILATION.
IMPORTANT NOTES
• Stop operation immediately if any liquid or solid object should fall into the cabinet.
• If the unit is not to be used for a long period of time, make sure that all power sources
are disconnected from the unit. Remove the battery from the remote control battery
compartment, and unplug the AC adapter from the wall outlet. Make it a practice to
remove the AC adapter by grasping the plug and not by pulling the cord.
• Places exposed to direct sunlight or close to heat radiating appliances such as electric
heaters.
• Places subject to constant vibration.
• Dusty, humid or moist places.
• Unplug the unit’s AC adapter from the electrical power outlet immediately in case of
malfunction.
E-
4
PROTECT YOUR FURNITURE
This model is equipped with non-skid rubber 'feet' to prevent the product from moving when
you operate the controls. These 'feet' are made from non-migrating rubber material specially
formulated to avoid leaving any marks or stains on your furniture. However certain types of
oil based furniture polishes, wood preservatives, or cleaning sprays may cause the 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any damage to your
furniture we strongly recommend that you purchase small self-adhesive felt pads, available
at hardware stores and home improvement centers everywhere, and apply these pads to
the bottom of the rubber 'feet' before you place the product on fine wooden furniture.
DEAR JENSEN CUSTOMER
Selecting fine audio equipment such as the unit you've just purchased is only the start of
your musical enjoyment. Now it's time to consider how you can maximize the fun and
excitement your equipment offers. This manufacturer and the Electronic Industries
Association's Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without
annoying blaring or distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing "comfort level" adapts to higher volumes
of sound. So what sounds "normal" can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
• Once you have established a comfortable sound level : Set the dial and leave it there.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a lifetime of
fun and enjoyment. Since hearing damage from loud noise is
often undetectable until it is too late, this manufacturer and the
Electronic Industries Association's Consumer Electronics Group
recommend you avoid prolonged exposure to excessive noise.
Customer's Record:
The serial number of this product is found on its back cover. You should note the serial
number of this unit in the space provided as a permanent record of your purchase to aid in
identification in the event of theft or loss.
Model Number: SMPS-750 Serial Number: ____________________
E-
5
MAIN UNIT
LOCATION OF CONTROLS
1. AUX IN 12. MODE/STANDBY
2. LED ON/OFF SWITCH 13. / CH-
. ECHO CONTROL 14. / SCAN
3
4. USB PORT 15. / CH+
5. SD CARD SLOT 16. LED DISPLAY
6. EQ ADJUSTMENT CONTROL 17. REPEAT
7. MIC IN 18. MASTER VOLUME
8. GUITAR IN 19. POWER SWITCH
9. TREBLE CONTROL 20. DC IN JACK
10. BASS CONTROL 21. AUX OUT
11. MIC/GUITAR VOLUME
E-
6
REMOTE CONTROL
The remote control operates on one CR2025 battery (i
ncluded).
To activate the remote control, remove the insulation tab inserted in the battery compartment.
When the operation of the remote control becomes intermittent or unsatisfactory, replace
the original battery with a new 3V lithium battery.
1. Press down on the compartment cover, slide out the battery holder from the remote
control case.
2. Replace the 3V CR2025 battery. Be sure the battery is installed correctly. The
remote will not work if the battery is installed with the wrong polarity.
CAUTION:
1. Danger of explosion if the battery is replaced incorrectly.
2. Replace only with the same or equivalent type battery.
Note: Only use a well-known brand of battery to ensure the longest life and best
performance.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
The remote control supplied with this product contains a coin/button cell battery. If the
coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and
can lead to death.
Keep new and used batteries away from children. If the battery compartment does not
close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
E-
7
CONTROLLING THE VOLUME
This unit features a MASTER VOLUME CONTROL (#18) located on the main unit. The
output volume level is initially controlled based on where this control is set.
It’s important that if you use the remote control to adjust the volume, make sure the MASTER
VOLUME CONTROL (#18) is always set to maximum prior to using the remote control.
Note: If the MASTER VOLUME CONTROL (#18) is set below the maximum volume level,
the output volume level will be reduced if you use the remote control. Example: if the
MASTER VOLUME CONTROL (#18) is set to 50%, you will only be able to adjust between
0 and 50% of the full volume when using the remote control.
When using the remote control to adjust the volume level, you will notice that the LED display
shows V00-V30 as you adjust the volume level. V00 meaning the lowest volume level, and
V30 is maximum. Make sure the volume level on the remote control is always left at V30 if
you decide to switch to using the MASTER VOLUME CONTROL (#18) instead of the remote
control. Leaving the remote control volume level set below V30 will reduce the audio output
on the SMPS-750. Turning the POWER SWITCH (#19) OFF and then ON again will reset
the volume control setting in the main unit, and restore full use of the MASTER VOLUME
CONTROL (#18).
LED DISPLAY
The LED display will show the following codes when that feature is active.
bt = displays when you are in BLUETOOTH mode
LInE = displays when you are in AUX mode
OnE = displays when “Repeat One” is selected during playback
ALL = displays when “Repeat ALL” is selected during playback
nOr = displays when “No Repeat” is selected during playback
6 Preset EQ Settings - Only accessible when using the "EQ" button on the remote control
nOr = displays when “NORMAL” EQ setting is selected
POP = displays when “POP” EQ setting is selected
rOC = displays when “ROCK” EQ setting is selected
JAZ = displays when “JAZZ” EQ setting is selected
CLA = displays when “CLASSIC” EQ setting is selected
Cut = displays when “COUNTRY” EQ setting is selected
Note: The preset EQ settings are only available when in Bluetooth or USB/SD modes.
Volume Level – Only shows when using the "VOLUME" buttons on the remote control V00
to V30
Note: The volume level range controlled by the remote control is limited by the MASTER
VOLUME CONTROL (#18). The MASTER VOLUME CONTROL (#18) should be set around
the half way point on the dial before you first power up the unit.
E-
8
POWER SOURCE
An AC 120V ~ 60Hz power adapter with an output voltage of DC15V 3A is included with the
SMPS-750.
POWER CONNECTION
1. Insert the DC plug of the AC adapter into the DC IN Jack (#20) on the unit.
2. Plug the AC adapter into an AC wall outlet.
3. Set the POWER Switch (#19) and the LED Switch (#2) to ON.
4. The SMPS-750 will turn ON, and all the LEDs on the top panel and in the speakers will
light.
Note:
Please remove the AC adapter from the wall outlet and unplug it from the SMPS-750 if the
unit is not being used for extended periods of time.
CAUTION
:
Only use the AC adapter included with the SMPS-750. Using a different adapter could
damage the unit and void the warranty.
RADIO OPERATION
The following steps can also be completed using the remote control. Check the remote control
diagram for the corresponding buttons.
1. Press the POWER SWITCH (#19) located on the back of the SMPS-750 to turn ON the
unit. Press and hold the MODE/STANDBY BUTTON (#12) to wake up the system if
necessary.
2. Tap the MODE/STANDBY BUTTON (#12) repeatedly to select FM mode. The frequency
will show on the LED DISPLAY (#16).
3. Press the BUTTON (#15) or BUTTON (#13) repeatedly to manually tune to a
desired station.
4. To automatically search for stations with strong signals, press and hold the
BUTTON (#15) or BUTTON (#13) until the frequency read out on display begins to
scan then release the button. The tuner will stop on the first strong station signal it finds.
5. Adjust the MASTER VOLUME CONTROL (#18) to the desired sound level.
To set / recall the radio presets
• The unit can automatically search and store the preset memories. Press and hold the
PLAY/PAUSE BUTTON (#14) for 4~5 seconds to activate auto preset mode and the
total number of stations can be stored depends on the signal strength of broadcasting
stations.
• To recall one of the preset stations already programmed, tap the PLAY/PAUSE
BUTTON (#14) repeatedly until you reach the desired preset number/radio station.
Notes:
• Use manual tuning to select weaker stations that might be skipped or missed during
automatic tuning.
• If the automatic tuning does not stop on the exact frequency of the station, for example,
it stops on 100.9MHz instead of 100.8MHz, use the manual tuning method to "fine tune"
to the exact frequency of the desired station.
• You can also direct enter the frequency by using the remote control.
For example, 88.1MHz (enter 881 with remote control), 100.8MHz (enter 1008 with
remote control).
E-
9
TIPS FOR BEST RECEPTION
FM - During FM reception, always keep the FM Wire Antenna fully extended and
hanging high up on the wall. If reception is weak, try
repositioning the FM Wire Antenna
until you find the strongest signal.
BLUETOOTH OPERATION
Pairing a Bluetooth enabled device with the SMPS-750.
1. Turn on the SMPS-750.
2. Tap the MODE BUTTON (#12) repeatedly to select Bluetooth mode. “bt” will appear on
the LED DISPLAY (#16) and flash. You will hear four (4) “beeps” confirming you are in
pairing mode.
3. Turn on the Bluetooth function of the device you want to link to and enable the search
or scan function to find the SMPS-750.
4. Select "SMPS-750" from the device list when it appears on your device screen. If
required, enter the pass code “0000” to pair (link) SMPS-750 with your device.
5. If you are pairing (linking) your computer to the speaker using Bluetooth, you may need
to set the SMPS-750 as your computer’s default sound device.
6. After successfully pairing the SMPS-750 with your Bluetooth device. You will hear two
(2) “beeps” confirming that the device is connected.
7. If you want to pair (link) the SMPS-750 with another Bluetooth device, disconnect the
connection by using the connected BT device. You will hear a disconnect tone which are
three (3) “beeps”. Repeat steps 3 & 4. You will hear a confirmation tone to confirm that
the new pairing is successful.
Now you can play music from your Bluetooth device wirelessly to the SMPS-750.
1. Select your favorite song, press the
PLAY/PAUSE BUTTON (#15)
on the SMPS-750 to play or pause the song from your
Bluetooth device.
2. Tap the BUTTON (#12) or BUTTON (#13) to select the Next or Previous track.
3. Slowly adjust both the volume control of your SMPS-750 and your Bluetooth device until
you reach a comfortable listening level.
Notes:
• Refer to the manual of your cell phone, tablet PC, computer or other Bluetooth
enabled devices for Bluetooth operation since it may vary from model to model.
• If your Bluetooth enabled device does not support A2DP profile, it will not play the
music through the speaker, even if paired (linked).
• Remember to turn off the SMPS-750 when you have finished listening.
• Don't forget to switch off the power of your Bluetooth device as well.
• The repeat function does not apply to the Bluetooth operation.
Play/Pause
on your Bluetooth device or the
E-
USB/SD PLAYER OPERATION
The SMPS-750 is compatible with, and will play MP3 files that are stored on a USB flash
drive or SD memory card.
1. Press the POWER SWITCH (#19) to turn the unit ON.
2. Plug a USB flash drive into the USB port (#4) or insert a SD CARD into the SD SLOT
(#5). The unit will automatically switch modes and begin reading the flash drive or SD
card. The total number of tracks will show on the LED DISPLAY (#16).
3. Press the PLAY/PAUSE BUTTON (#14) to pause the USB or SD card playback,
and press again to resume.
4. During PLAY mode, tap the
BUTTON (#15) or
BUTTON (#13), the player will
go to next or previous track.
5. During PLAY mode, press and hold the
BUTTON (#15) or
BUTTON (#13), the
player will play fast forward or fast backward.
6. Tap the REPEAT BUTTON on the remote control repeatedly during playback to select
repeat ONE, repeat ALL and cancel repeat.
AUX IN OPERATION
You can play other music sources (iPod, MP3 or other digital audio players) through the
speakers of the SMPS-750 by connecting the AUX IN Jack (#1) to your external player’s
audio out jack or headphone jack.
1. Plug one end of an audio cable (not included) into the AUX IN Jack (#1) and the other end
of the cable to the headphone jack of your digital audio player.
2. Turn on the SMPS-750 and your external audio device.
3. Press the MODE BUTTON (#12) repeatedly to select the AUX IN mode. ”LInE” will light
on the LED DISPLAY (#16).
4. The volume level can now be controlled through the main unit. Operate all other
functions on the auxiliary device as usual.
Notes:
• If you connect the SMPS-750 to the Line-Out Jack of your external device, you only
need to adjust the MASTER VOLUME CONTROL (#18) on your SMPS-750. If you
connect to the Headphone Jack of your external device, you may need to adjust both
the volume controls of your external device and the SMPS-750 to obtain the desirable
listening level.
• Remember to turn off the SMPS-750 when you have finished listening. Don't forget to
switch off the power of your external audio device as well.
E-10
AUX OUT CONNECTION
You can connect the SMPS-750 to an external Hi-Fi / AMPLIFIER system by connecting the
AUX OUT JACK (#21) to the auxiliary input jack on your Hi-Fi / Amplifier system with 3.5mm
cable (included).
Now you can adjust both the volume control of your external Hi-Fi / AMPLIFIER system and
the MASTER VOLUME CONTROL (#18) of the SMPS-750 to find the most desirable volume
setting.
USING THE UNIT AS A PUBLIC ADDRESS SYSTEM
This unit can also be used as a PA (Public Address System).
1. Plug the microphone or guitar (not included) into the MIC IN (#7)/GUITAR IN (#8) jack on
the top of the SMPS-750.
2. Turn on the SMPS-750.
3. Turn on your microphone or guitar (not included) and start your performance.
4. Adjust the MASTER VOLUME CONTROL (#18), MIC/GUITAR VOLUME (#11) and
ECHO CONTROL (#3) if necessary.
Note: To prevent feedback or loud whistling from occurring, please be sure that the
microphone is not held too close to the speakers on the SMPS-750.
RESETTING THE SMPS-750
In case of malfunction due to electrostatic discharge, reset the unit by disconnecting the DC
plug of the AC Adapter from its rear DC IN JACK (#20). Wait at least for 3 minutes before
reconnecting the DC plug to the DC IN JACK (#20).
CARE AND MAINTENANCE
• Do not subject the unit to excessive force, shock, dust or extreme temperatures.
• Do not tamper the internal components of the unit.
• Clean your unit with a dry cloth. Solvent or detergent should never be used.
• Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
• Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
CAUTION:
Never allow any water of other liquids to get inside the unit while cleaning.
Note: This unit is not magnetically shielded and may cause color distortion on the screen of
some TVs or video monitors. To avoid this, you may need to move the unit further away
from the TV or monitor if unnatural color shifts or image distortion occurs.
E-11
TROUBLESHOOTING
Fault
Possible Cause
s Solution
s
low.
volume.
Load MP3 songs into the flash
If you experience difficulties in the use of this music system, please check the following or
call 1-800-777-5331 for Customer Service.
No sound
Distortion of
sound
Karaoke
does not
work
MP3 does
not play
1. No input sound source.
2. Volume is too low.
1. Volume too high.
2. The speakers may be damaged.
1. Microphone plug is not fully
inserted.
2. Microphone switch is not on.
3. Microphone volume knob is too
1. The song format in the flash
drive is incompatible.
2. Improper operation has caused
a process disorder.
3. Flash drive/SD card are
disconnected.
1. Use a better music signal.
2. Adjust volume.
1. Turn down the volume.
2. Contact Customer Service for
repair instructions.
1. Plug microphone properly into
the socket.
2. Turn on microphone switch.
3. Increase the microphone
1.
drive or SD card.
2. Turn off the machine and then
turn on again.
3. Insert flash drive/SD card
properly.
SPECIFICATIONS
Power requirement:
AC adapter: Input AC 120V ~ 60Hz
Output DC 15V 3A
Main Unit DC input: DC 15V 3A
Battery for Remote Control: 1 x 3V CR2025 Lithium Battery
Frequency Range
Radio Band: FM 87.5 ~ 108 MHz
At Spectra, environmental and social responsibility is a core value
of our business. We are dedicated to continuous implementation
of responsible initiatives with an aim to conserve and maintain the
environment through responsible recycling.
Please visit us at http://www.spectraintl.com/green.htm for more information on Spectra’s
green initiatives or to find a recycler in your area.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Spectra Merchandising International, Inc. is under license.
Other trademarks and trade names are those of their respective owners.
E-12
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U.S.A. ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC. warrants this unit to be free from
defective materials or factory workmanship for a period of 90 days from the date of original
customer purchase and provided the product is utilized within the U.S.A. This warranty is
not assignable or transferable. Our obligation under this warranty is the repair or
replacement of the defective unit or any part thereof, except batteries, when it is returned to
the SPECTRA Service Department, accompanied by proof of the date of original consumer
purchase, such as a duplicate copy of a sales receipt.
You must pay all shipping charges required to ship the product to SPECTRA for warranty
service. If the product is repaired or replaced under warranty, the return charges will be at
SPECTRA’s expense. There are no other express warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
1. The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is
demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage
outside the descriptions and warnings covered within the user manual or nonSPECTRA approved modifications.
c. Claims are made within the warranty period.
2. This warranty does not cover damage or equipment failure caused by electrical wiring not
in compliance with electrical codes or SPECTRA user manual specifications, or failure to
provide reasonable care and necessary maintenance as outlined in the user manual.
3. Warranty of all SPECTRA products applies to residential use only and is void when
products are used in a nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary
from state to state. TO OBTAIN SERVICE please remove all batteries (if any) and pack the
unit carefully and send it freight prepaid to SPECTRA at the address shown below. IF THE
UNIT IS RETURNED WITHIN THE WARRANTY PERIOD shown above, please include a
proof of purchase (dated cash register receipt) so that we may establish your eligibility for
warranty service and repair of the unit without cost. Also include a note with a description
explaining how the unit is defective. A customer service representative may need to contact
you regarding the status of your repair, so please include your name, address, phone
number and email address to expedite the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for $60.00
to cover the cost of repair, handling and return postage. All out of warranty returns must be
sent prepaid.
It is recommended that you contact SPECTRA first at 1-800-777-5331 or by email at
custserv@spectraintl.com for updated information on the unit requiring service. In some
cases the model you have may be discontinued, and SPECTRA reserves the right to offer
alternative options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC.
4230 North Normandy Avenue,
Chicago, IL 60634, USA.
1-800-777-5331
To register your product, visit the link on the website below to enter your information.
http://www.spectraintl.com/wform.htm
0717 Printed in China
E-13
Loading...