Jensen Power760x5D, Power1100x1D Installation Manual

Power Series Class D Amplifiers

Installation Manual / Quick Start Guide

MODEL NUMBER FUSE SIZE MIN. WIRE GAUGE

2x30A

Power760x5D

Power1100x1D

3x35A

#4

#4

Installation Assistance

For installation assistance, call 1-866-382-5476 during normal business hours,
Monday-Friday, 9AM-5PM EST or visit www.jensenmobile.com at any time.

Supplies and Tools

To install the amplifier, you will need tools, supplies and adapters. It is best to
make sure you have everything you need before you start.

Disconnect Battery

Disconnect the negative (-) battery cable before starting the installation. Check
the battery ground (there should be two (2) ground wires coming from the

battery – one going to the starter mounting bolt or engine block and another
going to the vehicle chassis) and make sure the battery is grounded to the
chassis with at least a #4 gauge wire. Also check the alternator connections,
making sure they are tight and free from corrosion, rust or dirt.

Location and Mounting

The amplifier’s compact design allows great flexibility in mounting. Common

mounting locations include under the front passenger seat or in the trunk area.

When selecting a location, remember that amplifiers generate heat. Select a
location on a flat surface away from heat and moisture where air can circulate
around the amplifier.

Recommended Power Wire Size

Power Terminal (+12V) and Ground Terminal (Gnd)

Connect the main power wire to the battery, within 18 inches from the positive
(+) battery post, use an adequate size fuse or circuit breaker capable of
handling the current of the selected power wire. A fuse or circuit breaker must
be installed to prevent a possible electrical fire should the main power wire
short to ground.

POWER INPUT

GND REM +12V

Fuse or Circuit Breaker

Install as close to the

battery as possible.

Battery Terminal

Adapter

Make the ground lead as short as possible, leaving enough length to complete
the installation. To ensure a good ground, scrape away any paint or
undercoating to expose bare metal. Use a "ring" terminal of the proper gauge
and an "outside star washer" (between the chassis and ring terminal) when
making your ground connection.

Drill hole in chassis

Remote Terminal (Turn-On)

Connect the power antenna or amplifier turn-on lead (Switched +12VDC)
from the receiver to the amplifier remote terminal.

POWER INPUT

GND REM +12V

Remote Turn-On (Power Antenna) From Head Unit Receiver

B

A

L

T

SU

B-W

MO

NO

AS
/P

S

DIS

P

LOC/DX

1

2

INT

5

6

BAND

SCAN

i
EQ

MUTE

MODE

3

RPT

4

SHF

CD2620

DN

UP

i

BA

X

- SS

CH

A
NGER

40

WATT

Sx4

JPTH

CD

AU

-R/R
W

i

E

I
N
X

Q

4

AUX

CDRECE IVER

E

L

R

F

A

D

E

B

A

S

S

R

E

B

VOL

Drill hole in chassis sheet metal.

Note: Complete amplifier operation manuals are online at
www.jensenmobile.com

Speaker Wiring

The Speaker Wiring diagrams illustrate options for connecting speakers.
Observe the proper speaker polarity.

Power1100x1D

One Subwoofer

– – + +

Two Subwoofers

SPEAKER OUTPUT

4 Ohm / 2 Ohm

– – + +

SPEAKER OUTPUT

Power760x5D

Five Speakers

+ CH1 - + CH2 ­+ CH3 - + CH4 -

+ BRIDGED -

+ CH1 - + CH2 ­+ CH3 - + CH4 -

+ BRIDGED -

Power760x5D

Three Speakers

2 Ohm Minimum (Each)

4 Ohm / 2 Ohm Minimum

4 Ohm / 2 Ohm Minimum

4 Ohm Minimum

4 Ohm Minimum

Minimum load is 1 Ohm for any combination of subwoofers

2 Ohm Minimum

2 Ohm Minimum

Input Wiring

Most trunk/hatchback installations will require a 15-20 foot RCA cable, while
pickup trucks and under-seat mounting will require a 6-12 foot RCA cable.
Connect an RCA cable from your receiver to the RCA input on your amplifier.

Power1100x1D

Power760x5D

POWER

PROTECTION

BASS EQ

0

12

3

0.5

10

LEFT

RIGHT

LEVEL

6

0.3

2.5

V

LEVEL

6

0.3

2.5

V

LEVEL

6

0.3

2.5

V

FRONT

REAR SUB

FLAT HPF

FLAT HPF

X-OVER

MODE

5CH 4CH

REMOTE

LPFHPF

HPF

FRONT

REAR

SUB

3.5

1.5

5

16

Hz

160

16

Hz

160

30

Hz

160

3.5

1.5

3.5

1.5

5

1

30

22

45

22

45

35

80

30

50

150

RIGHT

LEFT

RIGHT

LEFT

POWER

PROTECTION

LEVEL

LOW
PASS

80

40

300

Hz

BASS

EQ

0

12

3

dB

SUB

SONIC

20

10

40

Hz

6

0.3

2.5

5

V

3.5

1.5

60

140

15

25

1

5

PHASE

OUTPUT

INPUT

REMOTE

©2015 Dual Electronics Corp. All rights reserved.

Printed in China

www.jensenmobile.com

Notes: