Jenn-Air W30400P, W30400PF, W30400PG, W30400PK, W30400PR Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

	This Data Sheet Includes Information On
	Jenn-Air
•	Product Model Number (s):		•
	30" Undercounter or Wall Ovens:
	W30400P, W30400PF, W30400PG, W30400PK,
	W30400PR and W30400PU
•	Dimensions (Actual Size)		•
	Cutout width:	28	3/16"
	Cutout height:	27	7/16"
	Minimum cabinet width:	30"
	Minimum cabinet depth:	23	1/2"

Recommended cutout location from floor : 4" to 33"

Distance from face of cabinet to

outer edge of open door (Door swing): 20 1/2"

Distance from face of cabinet to

front of closed door handle: 2 5/8"

Overall unit width: 29 3/4"

Overall unit height: 29"

Penetration into cabinet: 23 1/2"

Oven overlap distances when using cutout dimensions listed above:

Top overlap: 1 5/16"

Bottom overlap: 0"

Right side overlap: 3/4"

Left side overlap: 3/4"

•

Additional Information

•

•Total connected load: 3.6KW, 15 amps @120/240v. 3 wire single phase, 60Hz.

•A complete floor is recommended to prevent unusual drafts and capable of supporting 142 lbs.

•Minimum distance from bottom of opening to any object protruding from cabinet face (i.e. cabinet door) directly below: 7/8" (because it is an air flow area)

SEE PAGE 2 FOR UNDERCOUNTER INSTALLATION

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2002.	214

Cabinet Opening

(not to scale)

Locate electrical box in this location. Provide a 1 1/4" conduit hole in the rear right hand side of the opening floor.

30"

	28 3/16"
						23 1/2"

27 7/16"

4" to 33"

Overall Dimensions

(not to scale)

29"

23 1/2"

29 3/4"

2 5/8"

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN205.05 • A214B149 • • 032603 • 95654 • 23941
associated with reusing old Data Sheets.

www.dexpress.com					This Data Sheet Includes Information On
DIMENSION EXPRESS					Jenn-Air
	Page 2			•	Product Model Number (s):	•
Fax on Demand [phone]					30" Undercounter or Wall Ovens:
					W30400P, W30400PF, W30400PG, W30400PK,
					W30400PR and W30400PU
Additional Information:

•If you are stacking two units: Maximum distance from floor to bottom of lower oven opening is 7 1/2". Minimum distance from top of lower oven opening to bottom of upper oven opening is 1".

•House wire to enter junction box at left side. Range wires to enter right side of junction box.

•Can be installed under Jenn-Air models CCE1400, CCE3400, CCE3530, CCG2420 an CCG2421 cooktops..

•See below for undercounter installation.

Cabinet (under counter) Opening

25" normal counter top depth

CL

(not to scale)

Cooktops listed above

may be installed over

oven. See cooktop

installation instructions for

cooktop cutout size. The

1 1/2" countertop

oven cutout should be

27 7/16"

23 1/2"

located so that the oven

1 1/4" Dia conduit access hole as close

will not interfere with the

cooktop tub.

to the rear right corner as possible or in

adjacent right side compartment.

5/8" plywood bottom must

28 3/16"

support 142 pounds

36" standard countertop height

24"

1 1/2" countertop thickness

Recommended cutout:

36" countertop height reccomended

28 3/16" wide by 27 7/16" high

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.

Copyright © Dimension Express, 2002.

149

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN205.05 • A214B149 • • 032603 • 95654 • 23941
associated with reusing old Data Sheets.