Jenn-Air W10439669A User Manual

USE AND INSTALLATION INSTRUCTIONS

DUCT FREE DOWNDRAFT FILTER ACCESSORY KIT

INSTRUCTIONS D'UTILISATION ET D’INSTALLATION

SYSTÈME DE FILTRAGE SANS CONDUIT POUR

ÉVACUATION PAR LE BAS

Table of Contents/Table des matières

DOWNDRAFT FILTER SAFETY.....................................................1

INSTALLATION REQUIREMENTS................................................2

Tools and Parts ............................................................................2

Location Requirements................................................................2

INSTALLATION INSTRUCTIONS..................................................3

Install Cooktop in the Cabinet .....................................................3

Prepare the Base Cabinet Bottom...............................................4

Assemble Filter System ...............................................................7

Check Operation .......................................................................... 8

Filter System Care........................................................................8

TROUBLESHOOTING ....................................................................8

SÉCURITÉ DU FILTRE D’ÉVACUATION PAR LE BAS................9

EXIGENCES D’INSTALLATION.....................................................9

Outils et pièces.............................................................................9

Exigences d’emplacement.........................................................10

INSTRUCTIONS D’INSTALLATION.............................................10

Installation de la table de cuisson dans le meuble....................10

Préparation du plancher du placard inférieur ............................12

Assemblage du système de filtrage...........................................14

Contrôle du fonctionnement ......................................................15

Entretien du système de filtrage ................................................15

DÉPANNAGE.................................................................................16

DOWNDRAFT FILTER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT:

Installer: Leave installation instructions with the homeowner. Homeowner: Keep installation instructions for future reference.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

IMPORTANT :

Installateur : Remettre les instructions d'installation au propriétaire. Propriétaire : Conserver les instructions d'installation pour référence ultérieure.

W10439669A

IMPORTANT INSTRUCTIONS:

The Duct Free Filter Accessory Kit is designed to filter the air from the downdraft system and ventilate the conditioned air out into the room through the toe-kick area of the base cabinet. Do not ventilate the air from the downdraft system into the base cabinet, base cabinet pedestal, crawl space, wall or attic.

The Duct Free Filter cartridge is designed for six (6) months of normal cooking activity. The filter cartridge is not designed to be cleaned and reused. The filter must be changed as indicated by the Timestrip

. If the filter is not changed as recommended, the downdraft

performance will be reduced.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Too ls ne ed ed

■ Tape measure

■ Framing square

■ Hammer

■ Set punch

■ Pliers

■ Marker or pencil

■ Flat-blade screwdriver

■ Phillips screwdriver

■ Drill

■ ¼" (6.4 mm) drill bit

■ ⁷⁄₆₄" (2.8 mm) drill bit

■ Jigsaw or keyhole saw

■ Masking tape

Parts supplied

■ Flow test card

■ Poster board template

■ Duct free filter housing assembly

■ Flex duct

■ 2 - clamps

■ Duct free filter with Timestrip

■ 4 - mounting screws

Location Requirements

The Jenn-Air® Duct Free Filter System accessory is approved for use with JED3430, JED3536, JED 4430, JED4546, JGD3430, and JGD3536 series Jenn-Air downdraft products.

The Jenn-Air be installed in cabinetry that is constructed to meet Kitchen Cabinet Manufacturers Association (KCMA) requirements for toekick space. At a minimum, KCMA toe kick requires a depth dimension of 2½" (6.4 cm) and a height dimension of 3" (7.6 cm) as shown in the following illustration.

The Duct Free Filter

The Jenn-Air 1 Duct Free filter cartridge. The filter included with the kit comes with a 6 month Timestrip Timestrip filter housing.

After the installation is complete, press the button on the Timestrip Timestrip have elapsed.

A JDA8000WX replacement filter can be obtained by calling 1-800-JENNAIR (1-800-536-6247) or visiting www.jennair.com.

In Canada, call 1-800-807-6777 or visit www.jennair.ca.

Duct Free Filter System accessory is designed to

Duct Free Filter System accessory kit includes

sensor will be visible after the filter is installed in the

sensor to activate. Once activated, the window of the

sensor will darken along the time line until 6 months

A. Floor B. 2½" (6.4 cm) C. 3" (7.6 cm)

sensor preinstalled on the filter. The

INSTALLATION INSTRUCTIONS

Install Cooktop in the Cabinet

Follow the manufacturer’s recommended instructions for installing your downdraft cooktop with the downdraft blower exhaust scroll turned straight down.

To rotate the blower exhaust scroll down, complete the following steps.

Rotate Blower

IMPORTANT: The following additional steps must be performed

if the cooktop is being installed in a peninsula or island cabinetry. The blower exhaust scroll is shipped from the factory set to

exhaust straight out the back of the cabinet through an exterior wall.

NOTE: There are two different styles of blowers. See the following illustrations.

Blower Style A - With Top Label

To rotate blower:

1. Locate the 4 plastic plugs in the plenum bypass.

2. Use the pliers to remove the plastic plugs. IMPORTANT: Do not throw away the plastic plugs. The

plastic plugs must be reinstalled after the blower exhaust scroll has been rotated.

A. Blower motor B. Exhaust scroll C. Plenum

3. Insert the ³⁄₈" socket and extension into the hole and use the ratchet handle to loosen the nut half of a rotation. Repeat this process for each of the 4 nuts.

4. With the nuts loosened, the blower exhaust scroll can be easily rotated downward.

D. Blower bypass

E. Plastic plugs (4)

A. Blower exhaust scroll B. Plenum C. Blower motor

D. Top label

E. 10-32 machine nuts (4) F. Motor mounting plate

Blower Style B - Without Top Label

A. Blower exhaust scroll B. 10-32 machine nuts (4)

C. Plenum D. Motor mounting plate

E. Blower motor

5. Retighten each nut with the ³⁄₈" socket, extension and ratchet.

6. Reinstall the 4 plastic plugs.

To rotate blower motor (blower style A only):

NOTE: The “Top” label location on the blower motor is at the

9 o’clock position.

1. Using a ratchet with a ³⁄₈" socket and supporting the motor

with one hand, remove the 4 machine nuts that attach the blower motor to the exhaust scroll.

2. Remove the blower motor and wheel assembly from the weld

studs.

Prepare the Base Cabinet Bottom

Installation of the Jenn-Air® Duct Free Filter System requires modification to the cabinet base bottom in the toe-kick area of the base cabinet. A cutout and 4 pilot holes are required for mounting the Duct Free filter housing.

Remove Cabinet Brace

1. Open the cabinet doors.

2. Determine if a wooden or plastic brace is attached to the

cabinet floor and to the back of the center mullion as shown in the following illustration.

A. Top label B. Blower motor C. Motor mounting plate

D. Weld stud location

E. Blower wheel

3. When the motor mounting plate clears the threaded weld

studs, rotate the assembly clockwise 90° and reinstall the 4 #10-32 machine nuts.

4. Verify the “Top” label is positioned as shown.

A. Brace B. 2½" (6.4 cm)

C. 3" (7.6 cm) D. Floor

3. If a wooden or plastic brace is installed, remove the brace.

Cabinet Floor Cutout

The installation of the Jenn-Air® Duct Free Filter System Accessory Kit is dependent upon the type of cooktop purchased and the base cabinet dimension. For example, a 30" (76.2 cm) cooktop is designed to fit in a 30" (76.2 cm) base cabinet, and a 36" (91.4 cm) cooktop is designed to fit in a 36" (91.4 cm) base cabinet.

The poster board template provided with the kit is universal. However, the actual location of the exhaust cutout is different between the 30" (76.2 cm) and 36" (91.4 cm) products, due to the length difference between the base cabinets. The sketches that follow show the general position of the template.

For a 30" (76.2 cm) base cabinet: The template will be located in the front left corner. Note the area to be cut out of the cabinet floor is in the toe-kick area.

Top View of Cabinet

A. Top label

A. Front of cabinet B. Area to be cut out C. Toe kick

D. Template

E. Left side of cabinet

For a 36" (91.4 cm) base cabinet: The poster board template will be located closer to the center of the cabinet. Note the area to be cut out of the cabinet floor is in the toe-kick area.

Top View of Cabinet

3. Extend the line made in Step 1 to the cabinet front. NOTE: For clarity, the cabinet front is not shown in this view.

A. Front of cabinet B. Area to be cut out C. Toe kick

D. Template

E. Left side of cabinet

NOTE: For illustration purposes, the cabinet front is not shown in most of the following illustrations.

IMPORTANT: Do not cut the cabinet front. Cutout Steps

1. Use the framing square and draw a line on the cabinet floor

parallel to the edge of the blower exhaust scroll.

Top View of Cabinet

4. Locate template included with the installation kit.

A. Pilot hole locations B. Alignment notch

5. Center the line made in Step 3 within the alignment notch of the template. Make sure the edge of the template is against the cabinet front.

6. Tape template to bottom of cabinet with masking tape as shown in the following illustrations.

30" (76.2 cm) Base Cabinet Template Position

Top View of Cabinet

A. Blower exhaust scroll B. Framing square C. Cabinet floor

2. Flip the framing square over and slide it against the cabinet

front.

A. Left side of cabinet B. Toe-kick area

C. Area to be cut out

D. Cabinet front

E. Center mullion

+ 11 hidden pages