Jenn-Air W10274316B User Manual

JENN-AIR® 30", 36", AND 48" (76.2 CM, 91.4 CM, AND

121.9 CM) COMMERCIAL STYLE WALL-MOUNT CANOPY RANGE HOOD

HOTTE DE CUISINIÈRE JENN-AIR® DE STYLE

COMMERCIAL POUR POUR MONTAGE MURAL DE

30'', 36" ET 48" (76,2 CM, 91,4 CM ET 121,9 CM)

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à www.jennair.ca.

Table of Contents/Table des matières ...................2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

LI3UNB/W10274316B

TABLE OF CONTENTS

TABLE DES MATIÈRES

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS................................................5

Tools and Parts ............................................................................5

Location Requirements................................................................5

Venting Requirements..................................................................7

Electrical Requirements ...............................................................8

INSTALLATION INSTRUCTIONS.................................................. 8

Prepare Location..........................................................................8

Install Range Hood.......................................................................9

Install Range Hood Blower Motor................................................ 9

Make Electrical Connection .......................................................10

Complete Installation and Check Operation..............................11

RANGE HOOD USE......................................................................11

Range Hood Controls ................................................................11

RANGE HOOD CARE...................................................................12

Range Hood Lamps ...................................................................12

Cleaning......................................................................................12

WIRING DIAGRAM .......................................................................13

ASSISTANCE OR SERVICE.........................................................14

In the U.S.A. ...............................................................................14

Accessories................................................................................14

In Canada ...................................................................................14

WARRANTY ..................................................................................15

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE................................17

EXIGENCES D'INSTALLATION...................................................19

Outillage et pièces......................................................................19

Exigences d'emplacement.........................................................19

Exigences concernant l'évacuation ...........................................21

Spécifications électriques ..........................................................22

INSTRUCTIONS D'INSTALLATION.............................................22

Préparation de l'emplacement...................................................22

Installation de la hotte ................................................................23

Installation du moteur du ventilateur de la hotte .......................23

Raccordement électrique...........................................................24

Achever l'installation et vérifier le fonctionnement ....................25

UTILISATION DE LA HOTTE .......................................................26

Commandes de la hotte de cuisinière .......................................26

ENTRETIEN DE LA HOTTE DE CUISINIÈRE .............................26

Lampes de la hotte de cuisinière...............................................26

Nettoyage ...................................................................................27

SCHÉMAS DE CÂBLAGE ............................................................28

ASSISTANCE OU SERVICE.........................................................29

Au Canada..................................................................................29

Accessoires ................................................................................29

GARANTIE.....................................................................................30

RANGE HOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

■ Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the manufacturer.

■ Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

■ Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

■ Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for examination and/or repair.

■ Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

■ When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

■ Ducted fans must always be vented outdoors. CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into spaces within walls or ceilings, attics or into crawl spaces, or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

■ Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

■ Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

■ Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

■ Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING:

■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

■ NEVER PICK UP A FLAMING PAN - you may be burned.

■ DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

■ Use an extinguisher ONLY if:

– You know you have a class ABC extinguisher, and you

already know how to operate it.

– The fire is small and contained in the area where it

started. – The fire department is being called. – You can fight the fire with your back to an exit.

Based on "Kitchen Fire Safety Tips" published by NFPA.

■ WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control device.

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tool s neede d

■ Level

■ Drill

■ 1¼" (3 cm) drill bit

■ ¹⁄₈" (3 mm) drill bit if installing into wood and a ⁵⁄₁₆" (8 mm) drill

bit if installing optional backsplash kit.

■ Pencil

■ Wire stripper or utility knife

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

■ Scissors

Parts needed

■ Home power supply cable

■ 1 - ½" (12.7 mm) UL listed or CSA approved strain relief

■ 3 UL listed wire connectors

■ 1 wall or roof cap

■ Metal vent system

Parts supplied

Remove parts from packages. Check that all parts are included.

■ 2 metal grease filters for 30" (76.2 cm) models

3 metal grease filters for 36" (91.4 cm) models 4 metal grease filters for 48" (121.9 cm) models

■ Damper

■ Hood canopy with blower and halogen lamps installed.

■ 1 - 10" (25.4 cm) square to 10" (25.4 cm) round duct

transition.

■ 2 - 175 watt infrared heat lamps

■ Wood support

■ Grease collectors

■ 4 - 6 x 80 mm mounting screws

■ 4 - 3.5 x 9.5 mm screws

■ 6 - 4.2 x 19 mm screws

■ 5 - M6 x 16 mm screws

■ 5 - D6.4 x 11 mm washers

■ 2 - D5.3 x 20 mm washers

■ 2 - 10 x 50 mm wall anchors

■ T20

TORX®†adapter

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the rear wall of the range hood.

Canopy range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance.

The canopy range hood is factory set for venting through the roof or through the wall.

All openings in ceiling and wall where canopy range hood will be installed must be sealed.

For Mobile Home Installations

The installation of this range hood must conform to the Manufactured Home Construction Safety Standards, Title 24 CFR, Part 328 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD, Part 280) or when such standard is not applicable, the standard for Manufactured Home Installation 1982 (Manufactured Home Sites, Communities and Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local codes.

Product Dimensions

Front view

18¹⁄₁₆" (45.9 cm) for 48" (121.9 cm) Hood 12¹⁄₁₆" (30.6 cm) for 36" (91.4 cm) Hood 9¹⁄₁₆" (23.0 cm) for 30" (76.2 cm) Hood

6¹⁄₂" (16.5 cm)

2¹⁄₄" (5.7 cm)

25" (63.5 cm)

30" (76.2 cm) 36" (91.4 cm) 48" (121.9 cm)

12" (30.5 cm)

18" (45.7 cm)

†®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

Back view

9⁷⁄₈" (25.0 cm)

Installation Dimensions

30" (76.2 cm), 36" (91.4 cm),

48"

cabinet opening width

(If installed between cabinets)

(121.9

cm)

8³⁄₈" (21.3 cm)

18¹³⁄₁₆" (47.8 cm) for 48" (121.9 cm) Hood 12¹³⁄₁₆" (32.5 cm) for 36" (91.4 cm) Hood 9¹³⁄₁₆" (24.9 cm) for 30" (76.2 cm) Hood

A. Top of hood B. Wood support

C. Bottom of hood D. Home wiring system

E. Knockout into terminal box

Optional Full-Width Duct Cover Installations

12"

(30.5 cm)

12"

(30.5 cm)

18"

(45.7 cm)

18" (45.7 cm)

clearance upper

cabinet to countertop

A. 84" (213.4 cm) minimum for

installations with canopy only.

min.

36" (91.4 cm)

countertop height

Vent cover (if used)

Min. cabinet

opening width

Canopy

Bottom of canopy

to cooking surface

B. 96" (243.8 cm) minimum for

installations with optional duct cover.

13" (33.0 cm)

A B

A. Optional full-width duct cover B. Range hood

IMPORTANT:

Minimum distance “X”: 30" (76.2 cm) Suggested maximum distance “X”: 36" (91.4 cm)

Venting Requirements

■ Vent system must terminate to the outdoors.

■ Do not terminate the vent system in an attic or other enclosed

area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended.

Plastic or metal foil vent is not recommended.

■ The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use clamps to seal all joints in the vent system.

■ The vent system must have a damper. If the roof or wall cap

has a damper, do not use the damper supplied with the range hood.

■ Use caulking to seal exterior wall or roof opening around the

cap.

■ The size of the vent should be uniform.

Cold weather installations

An additional back draft damper should be installed to minimize backward cold air flow and a thermal break should be installed to minimize conduction of outside temperatures as part of the vent system. The damper should be on the cold air side of the thermal break.

The break should be as close as possible to where the vent system enters the heated portion of the house.

Makeup air

Local building codes may require the use of makeup air systems when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area.

Venting Methods

Calculating Vent System Length

To calculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece Equivalent Length

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

The maximum equivalent vent lengths are: 10" (25.4 cm) round vents - 60 ft (18.3 m)

Example vent system

90 elbow

2 ft

(0.6 m)

6 ft (1.8 m)

The following example falls within the maximum recommended vent length.

1 - 90° elbow = 5.0 ft (1.5 m) 1 - wall cap = 0.0 ft (0.0 m) 8 ft (2.4 m) straight = 8.0 ft (2.4 m)

Length of system = 13.0 ft (3.9 m)

Wall cap

A 10" (25.4 cm) round vent system is needed for installation (not included). The hood exhaust opening is 10" (25.4 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce performance.

Vent system can terminate either through the roof or wall.

Roof Venting Wall Venting

A. Roof cap B. 10" (25.4 cm) round vent*

A. Wall cap B. 10" (25.4 cm) round vent*

Electrical Requirements

Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

hood is installed.

■ If you are installing the optional backsplash with shelves for

heat lamps, follow the instructions included with that product.

■ Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent.

■ Check that all installation parts have been removed from the

shipping carton.

1. Disconnect power.

2. Determine which venting method to use: roof or wall exhaust.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

■ If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.

3. Remove the wood support from the back of the range hood

by loosening the 2 screws from the inside. Locate and level the top of the wood support 15³⁄₈" (39.1 cm) above the marked horizontal line and centered on the vertical centerline. Using 2 - 4 of the 6 x 80 mm screws, install wood support so that it is screwed into at least 2 vertical studs.

15³⁄₈"

(39 cm)

WARNING

Excessive Weight Hazard

Use two or more people to move and install range hood.

Failure to do so can result in back or other injury.

4. Using 2 or more people, lift range hood onto covered surface.

Range Hood Mounting Screws Installation

The hood is attached to the wall with the wood support that is attached to the back of the hood.

1. Determine and mark the centerline on the wall where the

canopy range hood will be installed.

2. Select a mounting height between a minimum of 30"

(76.2 cm) and a suggested maximum of 36" (91.4 cm), above the cooking surface and the bottom of the range hood and mark a horizontal reference line on the wall.

30" (76.2 cm)

to 36" (91.4 cm)

A. Wood support B. Centerline

NOTE: The screws provided for mounting this hood must be fastened into solid wood. Do not fasten into sheet rock only.

Optional Duct Cover Installation

→

1. Attach the full-width duct cover to the top of the range hood

with the screws provided with duct covers. The duct cover must be attached to the top of the range hood before mounting the range hood to the wall. For information on ordering the optional duct cover, see the “Accessories” section.

Complete Preparation

1. Determine and make all necessary cuts in the wall for the vent

system. Install the vent system before installing the range hood. See the “Venting Requirements” section.

2. Determine the location where the power supply cable will be

run through the wall.

3. Drill a 1¹⁄₄" (3.2 cm) hole at this location.

4. Pull enough power supply cable through the wall to allow for

easy connection to the terminal box.

5. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent

transition with damper to top of the range hood using 4 -

3.5 x 9.5 mm screws.

6. Remove terminal box cover and set aside.

7. Remove knockout from the back of the vent hood and install

a UL listed or CSA approved ¹⁄₂" strain relief. See “Make Electrical Connection” section.

8. Place the range hood near its mounting position and run the

power supply cable through the strain relief into terminal box (enough to make connection).

9. Tighten the strain relief screws.

4. Install 4 - 4.2 x 19 mm screws through the back of the hood

into the wood support and tighten.

5. Connect vent system to hood. Seal all joints with clamps.

6. If your installation uses the optional duct cover, mount it to

the top of the range hood following the instructions supplied with the duct cover.

Install Range Hood Blower Motor

1. Install the range hood blower motor assembly inside the hood

canopy with the wiring to the left.

A. Blower motor

2. Slide the left mounting plate flange under the bracket.

Install Range Hood

The hood attaches to the wall by the 2 mounting screws in the wood support mounted to the wall in the “Range Hood Mounting Screws Installation” section.

1. Using 2 or more people, hang the range hood on the wall by

placing the slotted holes in the range hood back over the 2 screws mounted to the wood support mounted to the wall.

NOTE: If your installation uses the optional duct cover, the vent system needs to be connected to the hood and the duct cover mounted to the top of the range hood before tightening the mounting screws. See steps 5 and 6.

→

2. Push the range hood up into the narrow slots, align the

bottom of the hood to the horizontal line, level the hood, and tighten the 2 mounting screws.

3. Mark 2 lower mounting hole locations. Drill ¹⁄₈" pilot holes if

the holes are located into wood. If holes are not located into wood, remove the hood and drill two ³⁄₈" pilot holes and insert 10 x 50 mm wall anchors. Remount the hood, level, and tighten the upper screws. Install 2 - 6 x 80 mm screws into the lower mounting anchors and tighten.

A. Bracket B. Mounting plate flange

3. Push the right end of the mounting plate up and snap into

spring tab. NOTE: The spring tab should be outside of the slot in the

mounting plate.

A. Spring tab

4. Align mounting holes and install 5 - 6 x 16 mm screws.

A. Screw B. Mounting hole

5. Attach power cord connector to connector on wire box on

blower motor mounting plate.

Make Electrical Connection

WARNING

Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Locate junction box inside of the range hood.

A. Terminal box cover B. Knockout in canopy

back into terminal box

A. Blower motor mounting plate B. Wire box connector

C. Power cord

A. White wires B. Black wires C. UL listed wire connectors D. Green, Bare or Yellow/Green wires

E. Home power supply

F. UL listed or CSA approved

3. Use UL listed wire connectors and connect black wires (B)

together.

¹⁄₂

" strain relief

+ 22 hidden pages