Jenn-Air SCE70600B, SCE70600W Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Updraft Grill-Range Ovens:

SCE70600B and SCE70600W

29 15/16"

26 3/8"

• Dimensions (Actual Size) •

Width:

29 15/16"

Depth:

26 3/8"

Height:

Door swing:

Height at full leg adjustment:

Height at 0" leg adjustment:

• Additional Information •

• Units can be installed as a Freestanding unit or

Slide-In unit. Slide-in installation does NOT allow for use of a backsplash or side panels. If either is desired, use the free-standing cutout and instructions.

• Units depth including door handle is 28 3/8".

• Electrical requirements: 120/240 VAC or 120/208

VAC, 60Hz. 50 amp grounded circuit protection is recommended, 40 amp minimum required.

• Proper operation requires use of range hood.

• Cabinetry over cooktop : 30' minimum clearance

between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet. 24" minimum when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or copper.

• To eliminate the hazard of reaching over heated

surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the hazard can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets.

• Range complies with U.L. requirements for 1"

clearance from the range to adjacent vertical side walls and 7/8" from rear wall. Abnormal surface unit operation could result in possible scorching of vertical walls and pose potential fire hazard. Therefore, a 6" minimum spacing is recommended.

• For Free-standing installations the cutout opening

width is 30 1/8" ± 1/16" minimum. The height of the countertop is 36" and countertop depth is 25". The cooktop does NOT need to be notched for Free-standing installations.

• See page 3 for Slide-in installation specifications

• Accepts Jenn-Air Designer Style cartridges.

See page 2 for additional information

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00. Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 • notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory • it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am • Sheets for each project, as opposed to the problems, time, costs, and risks associated with reusing old Data Sheets.

35 1/2" 20" 36" 35 1/2"

174

35 1/2"

Wall View

(not to scale)

Wall View

(not to scale)

18"

36"

Countertop

height

4 1/2"

30" Min.

Range

20"

Locate electrical supply junction box or 60" of electrical cable within shaded area.

Upper cabinets can only be 13" deep maximum. Over range cabinet is NOT recommended.

Minimum horizontal

30"

BN220.01 • A174B121 • 31469 • 000107 • 15410 • 26743

clearance between the edge of the appliance and combustible construction extending from the

cooking surface to 18" above the cooking surface is 1" to the sides and 7/8" to the back (see solid areas). 6" Minimum is recommended.

30 1/8" Minimum cutout width for Free-standing instalations.

(not to scale)

4 1/2"

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand (775) 833-3600

Additional Information:

• For European style cabinets (flush front) the required clearance for

operation of the oven door is a minimum spacing of 7/8" between the cutout and adjacent door, hinge or drawer of the cabinet.

• Island or peninsula installations with 24" deep base cabinets must

use flush back (no rear toe space) cabinets to avoid range interference,. If rear toe space is desired, use 27" or deeper cabinets.

• SCE70600B : Black.

• SCE70600W : White.

Page 2

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Updraft Grill-Range Ovens:

SCE70600B and SCE70600W

Kits:

• A501WT : 2 White side panels for freestanding range installations.

• A501BT : 2 Black side panels for freestanding range installations.

• A501LT : 2 Almond side panels for freestanding range installations.

• A507 : Custom backsplash for freestanding range installations.

• A510 : Trim Kit base for freestanding range installations.

• A521B : Deluxe black lighted backsplash for freestanding range installations.

• A521W : Deluxe white lighted backsplash for freestanding range installations.

29 3/8" countertop

opening

If the countertop overhangs the cabinet 1/2" to 1" the overall cutout depth is 22 5/8".

If the countertop overhangs the cabinet 1" to 1 3/4" the overall cutout depth is 23".

1/2" minimum flat

surface from back

edge of cutout

countertop thickness

1 3/4" Minimum from wall to

Cross Section

(not to scale)

rear countertop opening

Cabinet opening and from notch edge to notch edge

1 5/8" Maximum

21" from rear

cutout to notch

(cabinet face)

29 7/8"

The minimum clearance required between cabinet and cabinet drawer edge is minimum 7/8".

Slide-in installation

36" to Floor

(not to scale)

1/4"

29 7/8"

notch to notch

Notch on both

sides of opening

(not to scale)

BN220.01 • A174B121 • 31469 • 000107 • 15410 • 26743

121