Jenn-Air SCE70600B, SCE70600W Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

	This Data Sheet Includes Information On
	Jenn-Air
•	Product Model Number (s):			•
	Updraft Grill-Range Ovens:
	SCE70600B and SCE70600W
•	Dimensions (Actual Size)			•
	Width:	29	15/16"
	Depth:	26	3/8"

Height: 35 1/2"

Door swing: 20"

Height at full leg adjustment: 36"

Height at 0" leg adjustment: 35 1/2"

•

Additional Information

•

•Units can be installed as a Freestanding unit or Slide-In unit. Slide-in installation does NOT allow for use of a backsplash or side panels. If either is desired, use the free-standing cutout and instructions.

•Units depth including door handle is 28 3/8".

•Electrical requirements: 120/240 VAC or 120/208 VAC, 60Hz. 50 amp grounded circuit protection is recommended, 40 amp minimum required.

•Proper operation requires use of range hood.

•Cabinetry over cooktop : 30' minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet. 24" minimum when bottom of wood or metal cabinet is protected by not less than 1/4" flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" stainless steel, 0.024" aluminum or copper.

•To eliminate the hazard of reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the hazard can be reduced by installing a range hood that projects horizontally a minimum of 5" beyond the bottom of the cabinets.

•Range complies with U.L. requirements for 1" clearance from the range to adjacent vertical side walls and 7/8" from rear wall. Abnormal surface unit operation could result in possible scorching of vertical walls and pose potential fire hazard. Therefore, a 6" minimum spacing is recommended.

•For Free-standing installations the cutout opening width is 30 1/8" ± 1/16" minimum. The height of the countertop is 36" and countertop depth is 25". The cooktop does NOT need to be notched for Free-standing installations.

•See page 3 for Slide-in installation specifications

•Accepts Jenn-Air Designer Style cartridges.

See page 2 for additional information

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter-
mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2000.	174

29 15/16"

26 3/8"

(not to scale)

35 1/2"

20"

	Locate electrical
	supply junction
Wall View	box or 60" of
	electrical cable
(not to scale)	within shaded
	area.
	4 1/2"
4 1/2"
5"
	6"

Upper cabinets

can only be 13"

Wall View

deep maximum.

Over range

(not to scale)

30"

Min.

cabinet is NOT

recommended.

Minimum horizontal

clearance between the

30"

edge of the appliance and

combustible construction

6" extending from the

18"

cooking surface to 18"

above the cooking

surface is 1" to the sides

and 7/8" to the back (see

solid areas). 6" Minimum

36"

is recommended.

Countertop

Range

height

30 1/8" Minimum cutout

width for Free-standing

instalations.

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN220.01 • A174B121 • 31469 • 000107 • 15410 • 26743
associated with reusing old Data Sheets.

www.dexpress.com						This Data Sheet Includes Information On
DIMENSION EXPRESS						Jenn-Air
	Page 2				•	Product Model Number (s):	•
Fax on Demand [phone]						Updraft Grill-Range Ovens:
						SCE70600B and SCE70600W
Additional Information:
• For European style cabinets (flush front) the required clearance for		Kits:
operation of the oven door is a minimum spacing of 7/8" between the		• A501WT : 2 White side panels for freestanding range installations.
cutout and adjacent door, hinge or drawer of the cabinet.		• A501BT :	2 Black side panels for freestanding range installations.
• Island or peninsula installations with 24" deep base cabinets must		• A501LT :	2 Almond side panels for freestanding range installations.
use flush back (no rear toe space) cabinets to avoid range		• A507 : Custom backsplash for freestanding range installations.
interference,. If rear toe space is desired, use 27" or deeper cabinets.		• A510 : Trim Kit base for freestanding range installations.
• SCE70600B : Black.		• A521B :		Deluxe black lighted backsplash for freestanding range
• SCE70600W : White.		installations.
		• A521W : Deluxe white lighted backsplash for freestanding range
		installations.

29 3/8" countertop opening

If the countertop overhangs the cabinet 1/2" to 1" the overall cutout depth is 22 5/8".

If the countertop overhangs the cabinet 1" to

1 3/4" the overall cutout depth is 23".

Slide-in installation

(not to scale)

21" from rear

cutout to notch

(cabinet face)

29 7/8"

Cabinet opening and from notch edge to notch edge

1/4"

1/2" minimum flat
surface from back
edge of cutout
	1 5/8" Maximum
	countertop thickness
	1 3/4" Minimum from wall to
Cross Section	rear countertop opening
(not to scale)

29 7/8"

notch to notch

Notch on both

sides of opening

36" to Floor

(not to scale)

The minimum clearance required between cabinet and cabinet drawer edge is minimum 7/8".

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.

Copyright © Dimension Express, 2000.

121

• NEVER reuse Data Sheets. Data Sheets are subject to change without	• Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily,	• Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data	• Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks	BN220.01 • A174B121 • 31469 • 000107 • 15410 • 26743
associated with reusing old Data Sheets.