Jenn-Air SVE47100, SCE30500, SCE30600 User Manual

INSTALLATION

D INSTRUCTIONS

Models SVE47600, SVE47500, mmi_JENN.AIR

Range

403WESTFOURTHSTREET,NORTH• NEWTON,IA 50208

SVE47100, SCE30600, SCE30500

iNSTRUCTIONSTOINSTALLER:"Important:Saveforlocalelectricalinspector'suse".

• ALL RANGESCANTiP AND

CAUSEINJURIESTOPERSONS.

RangeOverall Dimensions:

Width - 29-15/16" (76.04 cm) _ • INSTALL ANTI-TIP DEVICES Height - 35-1/2" (90.17cm)

•Add 2" (5.08cm)for doorhandle

Depth - 26-3/8" (70.00cm) _ PACKEDWITH RANGE.

r" =.CTRICAL SPECIFICATIONS: 120/240 VAC OR 120/208 VAC 60 Hz 50 amp circuitprotectionrecommended,

,Imp minimum required. Wire size: For 50 amp service use #6 60°(3 or #8 75°C (copper only)three or four

r^_ductor, for 40 amp service use#8 (copperonly)three orfour conductor.

LECTRICAL CONNECTION: Unitto be properlycircuitprotectedand wired accordingto localelectricalcode and

,_ationalelectriccode, Unit power requirementslocated on serial plate on front of range.

• FOLLOWALL INSTALLATION INSTRUCTIONS.

WARNING

8101P265-60

(04-97-00)

1. UnpackRange (Figure1)

• Cut and remove shippingcarton.

• Removelowerrangepanelordrawer,andplaceoutofwork area.

• Removeblower package (if you havenot alreadydone so.) (Downdraft ModelsOnly.)

• LocateDuctingInstructionsheet.(DowndraftModelsOnly.) NOTE:Please read through entire installation instructionsand ducting 1

instructionspriorto beginninginstallation.

2. SelectRange Location(Figure2)

• Carefullyselecttherangelocation,keepinginmindthefollowing: (Figure 1)

A. Over-rangecabinetsarenotrecommended.However,ifnecessary,see

B. Makesure electricalpowercan be provided.(See#13.) _- _ _" C.For downdraftrangesplanthe rangeductingsystem. (Per#'s9-12and ', --"q-',_- -- '

ductinginstructions.) ._________L__.._--. D.Makesure thereis adequatespace. (See#'s 4, 5, 6, and7.) L_'N.J OVERNoTRECOMMIENDEDRANG[=CABINET E. islandor peninsularinstallationswith 24" deepbase cabinet must use _lscr,)1.24 (s_,)

rear toespace is desired,use 27" or deeper base cabinets.

NOTE:ThisrangecomplieswithULrequirementsfor"1"clearancefrom the _63._o¢,,)

rangeto adjacentverticalsidewallsand7/8" fromrearverticalwall. t ..

flushback (no reartoe space)cabinetstoavoid rangeinterference,lfa _, .' (

Abnormalsurfaceunitoperation(highheatand noutensils)could I,r_ resultinpossiblescorching,ofverticalwailsandposea potentialfire

hazard. Therefore, a _, (15.24 cm) minimum spacing is (Figure2) recommended.On Downdraftmodels6" spacingis requiredfor

properventilation.(Seeillustration.)

3. Typeof Installation(Free-Standing/Slide-In)(Figure3)

• Willrangebefree-standing?(Rangesettingonfloor.)Ifso, goto #7.

• Willrangebe slide-in?(Rangetoprestsoncountertop.)If so,goto#4.

• Theseapplianceshavebeendesignedinaccordaneewiththerequirements

ofvarioussafetyagenciesandcomplywiththemaximumallowablewood cabinet temperatures of 194°F. If these appliancesare installed with

cabinetsthathavea lowerworkingtemperaturethan194°F,discoloration, delaminationor meltingmayoccur. NOTE:Slide-incutoutdoesnotallowfor useofbacksplashorsidepanels.

Ifeitheraredesired,usethefree-standingcutoutand instruction. (Figure3)

• Moststandardcountersare25" (63.50cm)deep,36" (91.44cm)high,and extend1" (2.54cm) overthecabinet front.

• Measurethe countertop andoverhange.

25" MIN.

SLIDE-IN

4. Measurefor Slide-InCutout (Figure4) _!iii

(Figure4)

5.Slide-In Cutout (Figure5) * Usethe overhangmeasurementtofigure the "A"dimension:

Overhang 1/2" (1.27cm) to 1" (2.54cm) .... "A" = 22-5/8"(57,47cm)

Overhang1" (2.54cm) to 1-3/4" (4.45cm) .... "A" =23" (55.42cm)

. Carefullymarkthe countertopand recheckyourdimensions.

• Beforeyou cut,checkthe rear countertopdimensions. (See#6.)

NOTE:The minimumclearancebetweenthe cutoutandcabinetdoorsand

drawer edgeis7/8".

6. Slide-In Cutout (Figure6)

• Check your markedup dimensionscarefully.The rear dimensionsshown inthe illustrationmustbe maintained.

NOTE:Wherethis isnot done,it willbenecessaryto relieveaportionofthe (Figure5)

undersideof the countertopand/orsupport membersto clear the rangerear panel.

• Cuttingtolerance is = 1/'6(.16 cm.)

• Carefullymakethe cutout.

7. Free-StandingCutout (Figure7)

• 30-1/'8"(76.52cm) minimumclearance is required.

• Carefully markthe countertop,recheckyour dimensions and make the cutout.

NOTE:Range side panels may be desirable if the cutout is too large or (Figure6)

• Proceedto step 8. 3or.-_.1/le,,

_, Over-RangeCabinets (Figure8)

- Toeliminatethe hazard of reachingover a heated surface unit, cabinet _-"'T_'[

storagespaceabovethe rangeshould beavoided. Ifcabinet storageisto

beprovided,theriskcanbereducedbyinstallingarangehoodthatprojects horizontallya minimumof 5 inches beyond the bottom of the cabinets. However,if over-rangecabinetsare necessary,observethe following:

B = 30" (76.2cm) minimumclearance betweenthe top of the cooking

B = 24" (60,96ore) minimumwhen bottomof wood or metal cabinetis _J_______._-_. _

NOTE:

9. MeasureFor FloorVent //_/_

• If unit will beventedthrough the wall,go to #11. IF /

• Iffloor willbe concreteslab,see enclosedductinginstructions. _ O O O O

• For let and right hand venting through cabinet toe space, see special instructionsonpages7 & 8. (Figure8)

NOTE:Optimumcenterlineventlocationis 11"to17"fromedgeofcabinet.

cabinetsare on one sideofthe rangeonly. __.,._,.-_1/_

platformand the bottomof anunprotectedwoodor metal cabinet. (Figure7)

protectedby not less than 1/4" (0.635cm) FLAME RETARDANT _) millboardcoveredwithnotlessthan No.28MSGsheet steel, 0.015" _

(0.038cm)stainless steel,0.024" (0.061cm) aluminumor copper. _ _)" "" I _--

youare NOT installinga downdraftunit,skip to step 13. _ T

Ventslocatedlessthanthisdistancewill requiretheunittobe raised overblowerfor installation.

_" FloorVent Cutout(Figure 10)

- Checkthe directionof the floorjoists (seeillustration.)

• Locate6" squarecutout anywherewithin shadedarea. The cutout must miss the floor joists!

• Recheckyourdimensionsandmakethe cutout.

• Skipto Step#12. 3

(Figure 10)

11. WallVentCutout (Figure11)

center to center. II _- _ . WALLSTUD

• Willtheventductbe6" (15.24cm) roundthroughthewallor3-1/4" x 10"

(8.26cmx 25.4cm) rectangle,verticatlyinsidethewall? /"

• See DuctingInstructionsfor rearduct insidethe wall. Note: Cutoutin the wallmust clear3-1/4" x 10" (8.26cm x 25.4 cm)transition elbow.

• Locate the closest stud to your proposed vent hole location. Use the r_ (/_._ followingcharttofigurethe "X"dimension.Seetheillustrationforthe other

dimensions.

oceeveasuserr.uareusua0 c°si

"X"MINIMUM 4"(10.16cm) 6"(15.24cm) OUTSIDEWALL THEFLOOR

• A 1" (2.54cm)lengthofduct mustprotrudethroughthewallforconnection _- --"=""_._"D'U'_Th tOthe blower. (_

NOTE:Optimum vent location is 11" to 17" from edge of cabinet.Vents _1_] J'J_fT

12. InstallBlower (PriorToInstallingRange) (Figure 12) (Figure 12)

,3. InstallElectrical(Figure13)

locatedfrom9-3/8"to 11"will requireunittobe raisedover blowerfor

installation. METALJOUCTDucTTAPE I DUCT_TAPE

• Refertoyourvent plan. it maybe desirableto attachpart ofthe ducting to theblowerbeforeit isinstalled. L'IOCATEELECTRICA_'L

• Positiontheblower(seeillustration)andattachitto thefloorwithat least POWERIN two(2)screws: SHADEDAREA I

• Applyducttapearoundblowerexhaust/ductjoint.

• Note: Observealllocalelectricalcodes.

• CAUTION:Makesure powertocable is OFF. _

• Locatetheelectricpowersupplyinthefloororwall,anyplaceinthe shaded /.-_, 5FEETOF

areawhichwillcleartheblower. _) ELECTRICALCABLE

• DirectConnect.Pullthrough5' (152.4 cm)of electricalcable.

• RangeCord:Canadianunitsareequippedwitha range cord.Installa (Figure 13)

correspondingreceptacle.

VERTICALDUCTINSIDEWALL . . .

6"Round(15.24cm) 3-1/4"x10" (Figure11)

(8.26cmx25.4cm)

THROUGH THROUGH

12.54cm

I" )_

_ / j f j _r _.-iJ / _,3rf / _ _ _ Jrf Jttf n_f IF •

for properwiresize.)Iffour conductorwireisused,see #15for connection / _ cup to range, w_s,eR

• Seefrontcoveroftheseinstructionsfor propersupplyconnection.

• CAUTION:Makesurepowerto cable is OFF.

14. ConnectElectrical(Three ConductorWire)(Figure 14) __o t

• Remove the range electricalservicecover,located on the back, lower "-NEU'mAL(WHITE)

• Usethree orfourconductorcopperstandardpowercable (seefront cover __,_ w____

left-handcorner.

• Installa3/4" (1.91cm)clampintheholeprovidedbelowtheterminalblock. ,

• Strip3" (7.62cm) of outer insulationfromthe cable. (Figure 14)

• Strip1/2" (1.27cm) of insulationfromeachwire,

• Pull the cablethrough the cable clamp. Attach the BLACK, RED, and WHITE wires (see illustration.) Tightenthe terminal block nuts and the

cableclamp andinstallcover.

• On rangesequippedwith a rangecord, plugthe cord into its receptacle.

• Skipto Step #16.

_CABLE CLAMP_

+ 8 hidden pages