Jenn-Air S136, S136W, S156, S156W, S176 Dimension Guide

www.dexpress.com DIMENSION EXPRESS Fax on Demand [phone]

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

29 15/16"

26 3/8"

• Dimensions (Actual Size) •

Width:

29 15/16"

Depth:

26 3/8"

Height:

Door swing:

Height at full leg adjustment:

Height at 0" leg adjustment:

• Additional Information •

• Units can be installed as a Freestanding unit or

Slide-In unit. Slide-in installation does NOT allow for
use of a backsplash or side panels. If either is desired,
use the free-standing cutout and instructions.

• Units depth including door handle is 28 3/8".

• Electrical requirements: 120/240 VAC or 120/208

VAC, 60Hz. 50 amp grounded circuit protection is
recommended, 40 amp minimum required.

• Cabinetry over cooktop : 30' minimum clearance

between the top of the cooking surface and the bottom
of an unprotected wood or metal cabinet. 24" minimum
when bottom of wood or metal cabinet is protected by
not less than 1/4" flame retardant millboard covered
with not less than no. 28 MSG sheet steel, 0.015"
stainless steel, 0.024" aluminum or copper.

• To eliminate the hazard of reaching over heated

surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage
is to be provided, the hazard can be reduced by
installing a range hood that projects horizontally a
minimum of 5" beyond the bottom of the cabinets.

• Range complies with U.L. requirements for 1"

clearance from the range to adjacent vertical side walls
and 7/8" from rear wall. Abnormal surface unit
operation could result in possible scorching of vertical
walls and pose potential fire hazard. Therefore, a 6"
minimum spacing is recommended.

• For Free-standing installations the cutout opening

width is 30 1/8" ± 1/16" minimum. The height of the
countertop is 36" and countertop depth is 25". The
cooktop does NOT need to be notched for
Free-standing installations.

• See page 2 for Slide-in installation specifications

• Accepts Jenn-Air Designer Style cartridges.

See page 1A-5 for additional information

Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of deter­mining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

35 1/2"
20"
36"
35 1/2"

174

35 1/2"

Wall View

(not to scale)

4 1/2"

5"

Wall View

(not to scale)

18"

36"

Countertop

height

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

Locate electrical
supply junction
box or 60" of
electrical cable
within shaded
area.

30" Min.

30"

Range

20"

3"

Upper cabinets
can only be 13"
deep maximum.
Over range
cabinet is NOT
recommended.

Minimum horizontal
clearance between the
edge of the appliance and
combustible construction
extending from the

6"

cooking surface to 18"
above the cooking
surface is 1" to the sides
and 7/8" to the back (see
solid areas). 6" Minimum
is recommended.

30 1/8" Minimum cutout
width for Free-standing
instalations.

(not to scale)

6"

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

• For European style cabinets (flush front) the required clearance for

operation of the oven door is a minimum spacing of 7/8" between the
cutout and adjacent door, hinge or drawer of the cabinet.

• Island or peninsula installations with 24" deep base cabinets must

use flush back (no rear toe space) cabinets to avoid range
interference,. If rear toe space is desired, use 27" or deeper cabinets.

• S136, S156 and S176 : Black.

• S136W, S156W and S176W : White.

Kits:

• A501WT : 2 White side panels for freestanding range installations.

• A501BT : 2 Black side panels for freestanding range installations.

• A501LT : 2 Almond side panels for freestanding range installations.

• A507 : Custom backsplash for freestanding range installations.

• A510 : Trim Kit base for freestanding range installations.

• A519 : Deluxe black lighted backsplash for freestanding range

installations.

• A519W : Deluxe white lighted backsplash for freestanding range

installations.

Page 1a

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

282

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

1/2" minimum flat

surface from back

edge of cutout

Page 2

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

countertop thickness

1 3/4" Minimum from wall to

Cross Section

(not to scale)

If the countertop overhangs the cabinet 1/2"
to 1" the overall cutout depth is 22 7/8".

If the countertop overhangs the cabinet 1" to
1 3/4" the overall cutout depth is 23 3/16".

36"

countertop height

rear countertop opening

1 5/8" Maximum

21 1/8" from rear

Cabinet opening and

from notch edge to

notch edge

cutout to notch

(cabinet face)

29 7/8"

Slide-in/Drop-in instalation

29 3/8" countertop

opening

25" from top of
countertop to top of
under range panel

Cutout opening

(not to scale)

1/4"

• There MUST be 25" clear between the top of countertop and the top of under range panel.

• The appliance rests on the floor, so there CAN NOT be any cabinetry behind the under
range panel (shaded area) and toe kick.

• The under range panel and toe kick MUST be supplied by the builder.

• The under range panel (shaded area) must be removable for inspection and service.
Avoid attaching mounting hardware to adjacent cabinets, it will interfere with range removal.

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

36" to Floor

29 7/8"

notch to notch

Notch on both

sides of opening

(not to scale)

315

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

Page 3

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

A 1" length of duct must
protrude through the
back wall for connection
to the blower

Duct can be transitioned to 3
1/4" x 10" AFTER it passes
through the floor or back wall

Centerline of left

most placement of

6 1/4" Dia. hole for

ducting to the rear

8 1/2"

Floor View of Possible 6 1/4" Dia.

hole for ducting to the down

Wall View of Possible

Rear Venting Locations

17 1/8"

9 3/8"

Centerline of right

most placement of
ducting to the rear

(not to scale)

(not to scale)

3 1/4" x 10" duct

6" round duct

Common area

6 1/4" hole for

Wall

5 7/8"

10 5/8"

C

L

C

L

C

L

C

L

9 3/8"

17 1/8"

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

150

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

Page 4

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

36"

countertop height

Duct hole when venting
through the left cabinet

(not to scale)

31 1/4"

from top of countertop

5 1/2" Dia. hole

Floor View When Ducting Right or Left

Wall

6"

(not to scale)

Wall

Duct hole when venting

through the right cabinet

(not to scale)

31 1/4"

from top of countertop

Wall

6"

5 1/2" Dia. hole

36"

countertop height

11"

(1) 5" Dia. x 19" long Flex Duct (P/N 702935).
(1) 6" 90° elbow.
(2) Hose clamps (P/N 702331).

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

8 3/4"

8"2"

14"

Additional duct needed when venting left or right:

Make a cutout in the cabinet
floor of EITHER the left or the
right cabinet as shown by the

shaded areas

(1) 5" to 3 1/4" x 10" transition (P/N A453).
(2) Wood spacers (right side only) 1 1/2" thick x 9" long.

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

8 3/4"

8"

11"

2"

14"

123

www.dexpress.com

DIMENSION EXPRESS

Fax on Demand [phone]

Additional Information:

Ducting Installation Guidelines

Page 5

This Data Sheet Includes Information On

Jenn-Air

• Product Model Number (s): •

Downdraft Electric Grill-Range Ovens:

S136, S136W, S156, S156W, S176 and S176W

Unit is rated at a maximum of 60 feet of straight duct, 300CFM of
"make-up" is required. The blower has 2 range settings; Low range
is used when equivalent duct length is up to 30 feet and high range
is used when equivalent duct length is between 31 and 60 feet.

1. Use 6" diameter round or 3 1/4" x 10" rectangular only, except
for equivalent duct lengths of 10 feet or less that vent straight out
the back of the cooktop and directly through the wall. Equivalent
duct lengths of 10 feet or less can use 5" round duct. A transition
from 5" round duct is necessary when connecting to 6" round or
3 1/4" x 10" duct.

2. Do not use 5" elbows except in a 5" system. Instead use a 5" to
6" transition followed by a 6" elbow, or a 5" to 3 1/4" x 10" elbow
transition.

3. Use quality metal duct of at least 26 gauge galvanized or 24 gauge
aluminum. Inferior quality pipe fittings can cause up to twice the
restriction and is a poor value. 6" diameter PVC sewer pipe can be
used for under slab installations. Local codes may require a heavier
gauge material or restrict PVC. Check your local codes.

4. Distance between adjacent fittings (elbows, transitions etc.)

should be at least 18". The farther the better. Closer distance
promotes turbulence which reduces airflow.

5. The number of downstream elbows or transitions should be
limited to three. The initial 5" to 6" straight transition, if used, need
not be counted in this number.

6. Handmade crimps are likely to cause restrictions.

7. If an alternate wall or roof cap is used, be certain duct size is not
reduced, and there is a backdraft damper. It is best to use listed caps
to be certain of proper performance.

8. Thermal breaks: In areas of extreme cold weather, it may be
necessary to provide a short length of nonmetallic duct as close to
the wall as possible, to prevent conduction along the metal duct.

9. High altitude installations: It is advisable to reduce allowable duct
run by 20%.

10. In Canada, the installation must conform with local codes.

11. Elbows, wall caps and other fittings are shown below with their
equivalent straight duct length. Each fitting value must be added to
the amount of straight duct length used, to determine overall straight
duct equivalent length (60 feet maximum).

12. When using flexible duct multiply length of flexible duct by 2.

Duct Equivalents

Equivalent

Length

5 feet

5 feet

12 feet

0 feet

0 feet

0 feet

2 feet

Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.

• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at [phone] •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.

Duct

Fitting

6"

90° Elbow

3 1/4" x 10"

Elbow

3 1/4" x 10"

Flat Elbow

5" and 6"

Wall Caps

3 1/4" x 10"

Wall Cap

10" x 10"

Roof Jack

5" and 6"

Thermal

Break

Part

Number

5": A405
6": A406

A403

Legh: 5950
JA: 701943

5": 708786
6": 715557

Part

Number

A456

A496

A496

A463

A463

A495

Duct

Fitting

6"

45° Elbow

5" to 6"

Transition

6" to

3 1/4" x 10"

90° Elbow

3 1/4" x 10"

to 6"

90° Elbow

6" to

3 1/4" x 10"

Transition

3 1/4" x 10"

to 6"

Transition

5" to

3 1/4" x 10"

90° Elbow

BN221 • A174B282C315D150E123F124 • 31469 • 002906 • 143524 • 12927

Equivalent

Length

2 1/2 feet

1 foot

5 feet

9 feet

1 foot

4 1/2 feet

6 feet

Air flow this

direction NOT

recommended

Air flow this
direction NOT
recommended

Air Flow

Air Flow

Air Flow

Air Flow

Air Flow

Air Flow

124