Jenn-Air JXT8836ADS User Manual
RANGE HOOD
USER
GUIDE
TABLE OF CONTENTS
Safety Instructions....................................................1
Controls & Features...............................................2-4
Maintenance......................................................... 5-6
Warranty..................................................................7
Form No. A/04/03 Part No. US8800-0303A ©2003 Maytag Appliances Sales Co. Litho U.S.A.
Model Number: JXT8836ADS
Manufacturer Number: S88M90S
Size: 36”
USE AND CARE GUIDE
Read all Instructions before Installing and operating this appliance
MODEL: JXT8836ADS
Installation
The installation in this manual is intended for qualified installers,service technicians or persons
with similar qualified background.DO NOT attempt to install this appliance yourself. Injury could
result from installing the unit due to lack of appropriate electrical and technical background.
All electrical wiring must be properly installed, insulated and grounded. Overly accumulated
grease in old duct work should be cleaned out or duct work should be replaced if necessary to
avoid the possibility of a grease fire. Check all joints on duct work to insure proper connection
and all joints should be properly taped.
Operations
Read all instructions in this manual before operating the appliance. Save these instructions for
future reference.
Always leave safety grills and filters in place. Without these components, operating blo wers
could catch on to hair,fingers and loose clothing.
NEVER dispose cigarette ashes, ignitable substances, or any foreign objects into blowers.
NEVER leave cooking unattended.When frying, oil in the pan can easily overheat and catch fire.
The risk of self combustion is higher when the oil has been used several times.
Cleaning
The saturation of greasy residue in the blower and filters may cause increased flammability.
Keep unit clean and free of grease and residue build-up at all times to prevent possible fires.
Filters must be cleaned periodically and kept free from accumulation of cooking residue (see
cleaning instructions inside).Old and worn filters must be replaced immediately.Do not operate
blowers when filters are removed.Never disassemble parts to clean without proper instructions.
Disassembly is recommended to be performed by qualified personnel only.Call our service cen-
ter for removal instructions. 1-800-JENNAIR (1-800-536-6247)
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to negligence and the warranty of the
unit automatically expires due to improper maintenance.
* Please check for latest specification revisions before any custom work or cutouts.
IMPORTANT SAFETY NOTICE
WARNING
CONTROLS & FEATURES
2
TOUCH CONTROLS & FEATURES
The standard Metal Filters are required to be cleaned frequently and as recommended in order
to maintain blower efficiency.If improperly maintained, residue from cooking will sift though
filters and cause damage to hood blowers and other sensitive components; and possibly clog
duct work and create a fire hazard.
CONTROLS & FEATURES
3
CONTROLS: FILTER CHANGE INDICATOR (CARBON FILTERS)
Filter Change Reminder (Carbon, if fitted):
When your hood is installed as a 'Purifying' (Ductless Recirculating) unit, it is fitted with a set of
Carbon Filters to purify exhaust and fumes from cooking,then re-circulate the air within the home.
These Carbon Filters are required to be replaced after every 120 hours of use.The Filter Change
Reminder function in the microprocessor needs to be switched on.The microprocessor in the
controls when set, will elapse and count usa ge time and indicate by a flashing when carbon
filter replacement is needed.
Setting the Filter Change Reminder:
When Off, hold for approx. 5 seconds.
The display will change from
(exhaust mode) to , (purifying mode/
carbon filters used) this indicates that the
elapse timer function is switched on and
Carbon Filters are used.
Filter Replace Indicator:
When the display starts flashing, the
Carbon Filters require replacement.
Re-setting Function:
Once filters are replaced, with hood off,
press and hold , the display will appear;
hold for approximately 5 seconds until
on display disappears .The Filter
Change Reminder is now re-set and a new
120 hours elapse cycle is initiated.
Set Mode
hold 5 secs.
Change Filters
display from <--> to <C>
display <C> flashes
To Reset
hold 5 secs.
display from <C> to < >
CONTROLS & FEATURES
4
CONTROLS: FILTER CLEAN INDICATOR (METAL FILTERS)
Filter Clean Reminder (Standard Metal Filters fitted)
Whether your hood is installed as an Exhaust or Purifying unit, a set of metal filters are
fitted by the factory.These Metal Filters are intended to filter out residue from cooking.
They need not be replaced on a regular basis but are required to be kept clean.The Filter Change
Reminder function in the microprocessor will automatically indicate by a flashing
when the metal filters need to be cleaned after every 30 hrs. of use.
Filters can be cleaned by hand with non-abrasive soap or in a dishwasher. Heavily soiled
filters should also be soaked in grease cutting detergent such as Formula '409' or its equivalent,
prior to cleaning.
Filter Clean Reminder:
When flashes on display,the metal
filters installed are required to be cleaned.
This will occur after every 30 hours of use.
Re-setting Function:
Reset the Filter Clean Reminder timer when
filters are cleaned and re-installed.Press
and hold for approx. 5 seconds, the
display will appear; hold for approximately
5 seconds until on display disappears
.The Filter Clean Reminder function
is now re-set and a new 30 hours elapse
cycle is initiated.
Clean Filters
To Reset
hold 5 secs.
display <A> flashes
display from <C> to < >
MAINTENANCE
5
CLEANING
Surface Maintenance:
Clean periodically with hot soapy water and clean cotton cloth.Do not use corrosive or abrasive
detergent (e.g. Comet powder scrub, EZ-Off oven cleaner), or steel wool/scouring pads which will
scratch and damage surface.
For heavier soil use liquid degreaser such as “Formula 409”or “Fantastic” brand cleaner.
After cleaning,you may use non-abrasive stainless steel polish/ cleaners such as 3M or ZEP, to
polish and buff out the stainless luster and grain.Always scrub lightly,with clean cotton cloth,and
with the grain. Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Metal Filters
The Metal Filters fitted by the factory are
intended to filter out residue and grease
from cooking.They need not be replaced on a
regular basis but are required to be kept clean.
Filters should be cleaned after every 30
hours of use. Use the Filter Clean
Reminder function on the controls to
determine when filters require cleaning.
Remove and clean by hand or in
dishwasher. Spray 'Formula 409' or
equivalent degreasing detergent and leave
to soak if heavily soiled.
Dry filters and re-install before using hood.
Replacing Metal Filters
Should filters wear out due to age and
prolonged use, replace with following part
number:
Also replace any damaged filter that has
punctured or broken mesh, bent or broken frame.
Hood Model: Part No. Filters in pkg.
JXT8836ADS XXXXXXXX 3
MAINTENANCE
6
LIGHTS
Make sure all power is turned off and
bulbs are cool.
Remove by turning bulb counter
clockwise.
If bulbs are difficult to turn due to
prolonged use, firmly attach a glass
suction cup approx. the diameter of the
bulb and turn.
Replacement bulbs are available at
specialty lighting stores. Purchase type
GU10 120V 50W halogen bulbs.
Or to order bulbs, please call our service
center: 1-800-JENNAIR (1-800-536-6247)
Replacing Light Bulbs
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot
bulbs could cause serious burns.
WARRANTY
7
Warranty:
Full One Year Warranty - Parts and Labor
For one (1) year from the original retail purchase date, any part which fails in normal
home use will be repaired or replaced free of
charge.
Limited Warranty - Parts Only
Second Year - After the first year from the
original purchase date,parts which fail in normal home use will be repaired or replaced free
of charge for the part itself, with the owner
paying all other costs,including labor,mileage
and transportation.
Canadian Residents
The above warranties only cover an appliance
installed in Canada that has been certified or
listed by appropriate test agencies for compliance to a National Standard of Canada unless
the appliance was brought into Canada due to
transfer of residence from the United States to
Canada.
The specific warranties expressed above are the
ONLY warranties provided by the manufacturer.
These warranties give you specific legal rights,and
you may also have other rights which vary from
state to state.
What is Not Covered By These Warranties:
1. Conditions and damages resulting from an y of the following:
a. Improper installation, delivery, or maintenance.
b.Any repair,modification, altera tion, or adjustment not authorized
by the manufacturer or an authorized servicer.
c. Misuse, abuse, accidents, or unreasonable use.
d. Incorrect electric current, voltage, or supply.
e. Improper setting of any control.
2. Warranties are void if the original serial numbers have been removed,
altered, or cannot be readily determined.
3. Light bulbs.
4. Products purchased for commercial or industrial use.
5. The cost of service or ser vice call to:
a. Correct installation errors.
b. Instruct the user on the proper use of the product.
c.Transport the appliance to the servicer.
6. Consequential or incidental damages sustained by an y person as a
result of any breach of these warranties. Some sta tes do not allow the
exclusion or limitation of consequential or incidental damages, so the
above exclusion may not apply.
If You Need Service
• Call the dealer from whom your appliance was purchased or call
Maytag ServicesSM, Jennair Customer Assistance at 1-800-JENNAIR
(1-800-536-6247) USA and CANADA to locate an authorized servicer.
• Be sure to retain proof of purchase to verify warranty status. Refer to
WARRANTY for further information on owner’s responsibilities for warranty
service.
• If the dealer or service company cannot resolve the problem, write to
Maytag Services
SM
,Attn:CAIR®Center, P.O. Box 2370, Cleveland, TN
37320-2370,or call 1-800-JENNAIR (1-800-536-6247) USA and CANADA.
U.S. customers using TTY for deaf, hearing impaired or speech
impaired, call 1-800-688-2080.
NOTE:
When writing or calling about a service problem, please include the
following information:
a.Your name, address and telephone number;
b. Model number and serial number;
c. Name and address of your dealer or servicer;
d.A clear description of the problem you are having;
e. Proof of purchase (sales receipt)
• User’s guides,service manuals and parts information are available from
Maytag Services
SM
, Jennair Customer Assistance.
Loading...