Jenn-Air JWD3030EP, JWD3030ES Installation Instructions

INSTALLATION INSTRUCTIONS 24" (60.9 CM),

IMPORTANT:

IMPOR

À conser

27" (68.6 CM), AND 30" (76.2 CM) INDOOR/

OUTDOOR ELECTRIC WARMING DRAWER

INSTRUCTIONS D’INSTALLATION POUR TIROIR-

RÉCHAUD ÉLECTRIQUE POUR USAGE INTÉRIEUR/

EXTÉRIEUR DE 24" (60,9 CM), 27" (68,6 CM), ET

30" (76,2 CM)

Table of Contents/Table des matières

WARMING DRAWER SAFETY.......................................................2

INSTALLATION REQUIREMENTS .................................................3

Tools and Parts .............................................................................3

Location Requirements ................................................................3

Electrical Requirements ...............................................................6

INSTALLATION INSTRUCTIONS ...................................................6

Install Warming Drawer ................................................................6

Complete Installation ...................................................................7

CUSTOM DRAWER FRONT INSTALLATION

INSTRUCTIONS FOR WARMING DRAWERS ..............................7

Tools and Parts .............................................................................7

Install Custom Drawer Front Panel ..............................................7

SÉCURITÉ DU TIROIR-RÉCHAUD ..............................................9

EXIGENCES D’INSTALLATION ...................................................10

Outillage et pièces ......................................................................10

Exigences d’emplacement .........................................................10

Spéciﬁcations électriques ..........................................................13

INSTRUCTIONS D’INSTALLATION ............................................. 13

Installation du tiroir-réchaud ......................................................13

Achever l’installation ..................................................................14

INSTRUCTIONS D’INSTALLATION DE LA FAÇADE

DU TIROIR PERSONNALISÉ POUR TIROIR-RÉCHAUD ..........14

Outillage et pièces ......................................................................14

Installation du panneau de la façade du tiroir personnalisé ......14

ve for local electrical inspector's use.

W10845860A

TANT :

ver pour consultation par l'inspecteur local des installations électriques

WARMING DRAWER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

You

can be killed or seriously injured if you don't

instructions.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools needed

■ Phillips screwdriver

■ Flat-blade screwdriver

■ Measuring tape

■ Level

■ Drill

■ 1

/8" (3.5 cm) hole saw

Parts supplied

■ Two #8-18 x

■ Lens (for panel ready models)

Check local codes. Check existing electrical supply. See “Electrical Requirements.”

It is recommended that all electrical connections be made by a licensed, qualiﬁed electrical installer.

/2" screws

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ Cutout dimensions that are shown must be used. Given

dimensions provide minimum clearance with warming drawer.

■ Recessed installation area must provide complete enclosure

around the recessed portion of the warming drawer.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Electrical supply outlet should be located in the rear wall

on the upper right-hand side of the cutout or in an adjacent cabinet. The outlet must be recessed. If the electrical outlet is located in an adjacent cabinet, a 13/8" (3.5 cm) minimum diameter hole should have been drilled in the back of the cutout or support surface to pass the power supply cord through to the outlet.

■ Warming drawer support surface must be solid, level,and

ﬂush with bottom of cabinet cutout.

■ Warming drawers with oiled bronze, black glass, and white

glass panels are approved for indoor use only.

■ Support surface must be solid, level, and ﬂush with the

bottom of the cabinet cutout.

■ 24" (61.0 cm) minimum cabinet depth.

For best performance results make sure the warming drawer is leveled before completing installation. There is no way to level the warming drawer after it has been installed. If the installation is not level, the door may slide open or not seal tightly, allowing heat to escape.

NOTE: If installing the warming drawer below another product, refer to that product’s literature for any installation requirements.

Product Dimensions

WARMING DRAWER SIZE

24" (60.9 cm) 231/8" (58.7 cm) 221/4" (56.5 cm) 9" (22.9 cm) 233/4" (60.3 cm) 101/4" (26.1 cm)

27" (68.6 cm) 231/8" (58.7 cm) 251/4" (64.1 cm) 9" (22.9 cm) 263/4" (67.9 cm) 101/4" (26.1 cm)

30" (76.2 cm) 231/8" (58.7 cm) 281/4" (71.8 cm) 9" (22.9 cm) 293/4" (75.6 cm) 101/4" (26.1 cm)

OVEN DEPTH (A)

RECESSED WIDTH (B)

RECESSED HEIGHT (C)

OVERALL WIDTH (D)

DRAWER FRONT HEIGHT (E)

Clearance Dimensions

Front view

120 volt grounded outlet (or located in adjacent cabinet)

Warming drawer cutouts

Toe kick

WARMING DRAWER SIZE

MINIMUM BETWEEN

CUTOUT HEIGHT (B)

CUTOUTS (A)

24" (60.9 cm) 21/2" (6.4 cm) 91/8" (23.2 cm) 1" (2.5 cm)/

27" (68.6 cm) 21/2" (6.4 cm) 91/8" (23.2 cm) 1" (2.5 cm)/

30" (76.2 cm) 21/2" (6.4 cm) 91/8" (23.2 cm) 1" (2.5 cm)/

Warming drawer can be installed as an indoor single or double installation or installed under a single oven. Two warming drawers under a single oven are shown.

NOTE: The warming drawer cannot be leveled after being installed.

For outdoor installation, follow the cutout dimensions above. Install the outdoor warming drawer in a permanent ﬁxture.

MINIMUM/ RECOMMENDED (C)

CUTOUT WIDTH (D)

MINIMUM CABINET WIDTH (E)

41/4" (10.8 cm)

221/2" (57.1 cm) 24" (60.9 cm)

251/2" (64.8 cm) 27" (68.6 cm)

281/2" (72.4 cm) 30" (76.2 cm)

Custom Wood Drawer Front

If you plan to install a custom wood panel to match your cabinets, we recommend consulting a qualiﬁed cabinetmaker or carpenter. The back of the wood panel must be sealed to avoid moisture damage.

Clearance Dimensions - Flush Installation

Front View

Cabinet

Side View

Top View

1" (25 mm) Side Cleats*

⁷⁄₈” (22 mm) Platform*

Back

Side Cleat*

1⁵⁄₈" (4.1 cm)

27" Models 30" Models

Width of ﬂush inset cutout (minimum) 27

Height between cutouts (minimum) 2

Height of ﬂush inset cutout (minimum) 10 Bottom of cutout to ﬂoor (recommended) 8

Bottom of cutout to ﬂoor (minimum) 5" (12.7 cm) 5" (12.7 cm)

Width of opening (minimum) 25

Depth of cutout (minimum) 25" (63.5 cm) 25" (63.5 cm)

Recommended outlet location

Flush Installation Requirements

/4" (69.2 cm) 301/4" (76.8 cm)

/2" (6.4 cm) 21/2" (6.4 cm)

/4" (27.3 cm) 103/4" (27.3 cm)

/4" (21.0 cm) 81/4" (21.0 cm)

/4" (64.1 cm) 281/4" (71.8 cm)

A 25" (63.5 cm) minimum cutout depth is required. These dimensions will result in a 1/4" (6 mm) reveal on all sides of the warming drawer. * The front face of the cleats and platforms will be visible and should be treated as a ﬁnished surface.

+ 11 hidden pages