How it Works
Jenn-Air
Loading...
JWD2130WR00
Installation Guide
12 pgs1.1 Mb0
Owner’s Manual
20 pgs2.83 Mb0

Jenn-Air JWD2030WS00, JWD2030WX00, JWD2130WB00, JWD2130WP00, JWD2130WR00 Installation Guide

...
INSTALLATIONINSTRUCTIONS
24" (61 CM), 27" (68.6 CM), AND 30" (76.2 CM)
INDOOR/OUTDOOR ELECTRICWARMING DRAWER
INSTRUCTIONSD'INSTALLATION
TIROIR-RECHAUD ELECTRIQUEPOUR USAGE
INTI_RIEUR/EXTI:RIEURDE
24" (61 CM), 27" (68,6 CM), ET30" (76,2 CM)
Table of Contents/Table des mati_res
Tools and Parts ............................................................................ 3
Location Requirements ................................................................ 3
Electrical Requirements ............................................................... 4
Install Warming Drawer ................................................................ 5
Complete Installation ................................................................... 5
CUSTOM DRAWER FRONT INSTALLATION INSTRUCTIONS
Tools and Parts ............................................................................ 6
Install Custom Drawer Front Panel .............................................. 6
Outillage et pieces ........................................................................ 8
Exigences d'emplacement ........................................................... 8
Specifications electriques ............................................................ 9
INSTRUCTIONS D'INSTALLATION ............................................. 10
Installation du tiroir-rechaud ...................................................... 10
Achever I'installation .................................................................. 10
INSTRUCTIONS D'INSTALLATION DE LA FA(_ADE DU
TIROIR PERSONNALISI_ POUR TIROIR-RECHAUD ................ 11
Outillage et pieces ...................................................................... 11
Installation du panneau de la fa£;ade du tiroir personnalise ......11
iMPORTANT:
Save for local electrical inspector's use.
iMPORTANT :
,&,conserver pour consultation par I'inspecteur local des installations 61ectriques.
W10276326A
WARMING DRAWERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
2
INSTALLATIONREQUIREMENTS
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed
here.
Tools needed
• Phillips screwdriver
• Drill
• 13/8"(3.5 cm) hole saw
Product Dimensions
C
Parts supplied
• 4- #8-18 x %"screws
• Lens (for panel ready models) Check local codes. Check existing electrical supply. See
"Electrical Requirements." It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
IMPORTANT: Observe all governing codes and ordinances.
• Cutout dimensions that are shown must be used. Given dimensions provide minimum clearance with warming drawer.
• Recessed installation area must provide complete enclosure around the recessed portion of the warming drawer.
• Grounded electrical supply is required. See "Electrical Requirements" section.
• Electrical supply outlet should be located in the rear wall on the upper right-hand side of the cutout or in an adjacent
cabinet. The outlet must be recessed. If the electrical outlet is located in an adjacent cabinet, a 13/8"(3.5 cm) minimum
diameter hole should have been drilled in the back of the cutout or support surface to pass the power supply cord
through to the outlet.
• Warming drawer support surface must be solid, level and flush with bottom of cabinet cutout.
• Warming drawers with oiled bronze, black glass, and white glass panels are approved for indoor use only.
For best performance results make sure the warming drawer is leveled before completing installation. There is no way to level the warming drawer after it has been installed. If the installation is not level, the door may slide open or not seal tightly, allowing heat to
escape.
l
WARMING OVERALL RECESSED RECESSED
DRAWER WIDTH (A) WIDTH (B) HEIGHT (C)
SIZE
24" 233/4" 221/4" 9" (61 cm) (60.3 cm) (56.5 cm) (22.9 cm)
27" 263/4'' 25V4" 9" (68.6 cm) (67.9 cm) (64.1 cm) (22.9 cm)
30" 293/4'' 28V4" 9" (76.2 cm) (75.6 cm) (71.8 cm) (22.9 cm)
Cabinet Dimensions
Cabinet Side View
Warming Support surface must be drawer solid, level, flush with front of cabinet cutout.
223/4''
L (57.8 cm) _.J I
F receseed-I I
I I
depth
Cabinet Front View
120 volt grounded
outlet (or located in adjacent
cabinet)
Warming
drawer
oi
o
21/(6.4 cm) rain.
91/8'' (23.2 cm)
' (6.4 cm) rain.
91/8'' (23.2 cm)
E ¸ _ _,_ _ i'¸ _
Electrical Shock Hazard
Plug into a grounded 3 prong outlet. Do not remove ground prong.
Do not use an adapter. Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
l ecommended 4114"(10.8 cm)
Minimum 1" (2.5 cm)
--T-(10.2 cm)
WARMING CUTOUT MIN. CABINET
DRAWER SIZE WIDTH (A) WIDTH (B)
24" (61 cm) 221/2'' (57.1 cm) 24" (61 cm) 27" (68.6 cm) 251/2'' (64.8 cm) 27" (68.6 cm) 30" (76.2 cm) 281/2'' (72.4 cm) 30" (76.2 cm)
Warming drawer can be installed as an indoor single or double installation or installed under a single oven. Two warming drawers under a single oven are shown.
NOTE: The warming drawer cannot be leveled after being installed.
For outdoor installation follow the cutout dimensions above. Install the outdoor warming drawer in a permanent fixture.
Custom Wood Drawer Front If you plan to install a custom wood panel to match your
cabinets, we recommend consulting a qualified cabinetmaker or carpenter. The back of the wood panel must be sealed to avoid moisture damage.
IMPORTANT: The warming drawer must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.
A copy of the above code standards can be obtained from: National Fire Protection Association
One Batterymarch Park Quincy, MA 02269
CSA International 8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
• A 120 volt, 60 Hz., AC only, 15-amp fused, electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this warming drawer be provided.
• The model/serial rating plate is located above the left-hand side receiving slide. The warming drawer must be removed to view the model/serial rating plate. See the illustration below.
A
A. Model/serial number plate
Loading...
+ 8 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use