Jenn-Air JUD278DBCX00 Installation Guide

JENN-AIR_DOUBLEREFRIGERATORDRAWERS/

CAJON REFRIGERADODOBII::JENN-AIR_

DOUBLETIROIRRI_FRIGERI_JENN-AIR_

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. INSTALLATION REQUIRES 2 OR MORE PEOPLE.

IMPORTANTE: LEA Y GUARDE ESTAS INSTRUCCIONES. LA INSTALACION REQUIERE DE 20 MAS PERSONAS.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS. L'INSTALLATION NI2CESSITE L'INTERVENTION DE

Table of Contents/indice/Table des matieres ...................................................................................... 2

_]ENN-AIRo

W10122760A

INSTALLATIONGUIDE

MANUAL DEINSTALACION

GUIDED'INSTALLATION

2 PERSONNES OU PLUS.

TABLEOF CONTENTS

REFRIGERATOR DRAWERS SAFETY .......................................... 3

Proper Disposal of Your Old Refrigerated Appliance .................. 3

DESIGN SPECIFICATIONS ............................................................ 3

Models .......................................................................................... 3

INSTALLATION REQUIREMENTS ................................................ 4

Tools and Parts ............................................................................ 4

Style 2: Custom Overlay Drawer Panels ...................................... 4

Product Dimensions ..................................................................... 5

Location Requirements ................................................................ 6

Electrical Requirements ............................................................... 6

iNDICE

SEGURIDAD DE LOS CAJONES REFRIGERADOS .................. 13

C6mo deshacerse adecuadamente de

su aparato refrigerado viejo ....................................................... 13

ESPECIFICACIONES DE DISEI_IO .............................................. 13

Modelos ...................................................................................... 13

REQUlSITOS DE INSTALACION ................................................. 14

Piezas y herramientas ................................................................ 14

Estilo 2: Paneles de los cajones recubiertos a la medida ......... 14

Medidas del producto ................................................................ 15

Requisites de ubicaci6n ............................................................. 16

Requisites electricos .................................................................. 16

INSTALLATION INSTRUCTIONS .................................................. 6

Unpack the Refrigerator Drawers ................................................ 6

Remove the Base Grille ................................................................ 7

Style 2: Install Custom Overlay Drawer Panels ........................... 7

Install the Mounting Brackets ...................................................... 9

Move the Refrigerator Drawers to Final Location ...................... 10

Lower the Leveling Legs ............................................................ 10

Level the Refrigerator Drawers .................................................. 10

Attach the Mounting Brackets to Adjacent Cabinets ................ 11

Reinstall the Base Grille ............................................................. 11

Complete Installation .................................................................. 11

INSTRUCCIONES DE INSTALACION ......................................... 16

C6mo desempacar los cajones refrigerados ............................. 16

C6mo quitar la rejilla de la base ................................................. 17

Estilo 2: Instalaci6n de los paneles de

los cajones recubiertos a la medida .......................................... 17

C6mo instalar los soportes de montaje ..................................... 19

Mueva los cajones refrigerados a su posici6n final ................... 20

C6mo bajar las patas niveladoras .............................................. 20

Nivelaci6n de los cajones refrigerados ...................................... 20

C6mo fijar los soportes de montaje a

los gabinetes adyacentes .......................................................... 21

C6mo reinstalar la rejilla de la base ........................................... 21

Complete la instalaci6n .............................................................. 21

TABLEDESMATIERES

SECURITI :!:DES TIROIRS REFRIGI:!:RI:!:S.................................... 22

Mise au rebut correcte de votre vieil appareil refriger6 ............. 22

SpI_CIFICATIONS DU DESIGN ................................................... 22

Modeles ...................................................................................... 22

INSTRUCTIONS D'INSTALLATION ............................................ 23

Outillage et pieces ...................................................................... 23

Style 2 : Panneaux decoratifs de tiroirs personnalises ............. 23

Dimensions du produit ............................................................... 24

Exigences d'emplacement ......................................................... 25

Specifications electriques .......................................................... 25

INSTRUCTIONS D'INSTALLATION ............................................ 26

Deballage des tiroirs refrigeres .................................................. 26

Depose de la grille de la base .................................................... 26

Style 2 : Installation des panneaux decoratifs

de tiroir personnalises ................................................................ 26

Installation des brides de montage ............................................ 28

Deplacement des tiroirs refriger6s a leur emplacement final ....29

Deploiement des pieds de nivellement ...................................... 29

Reglage de I'aplomb des tiroirs refrig6res ................................. 29

Fixation des brides de montage sur les placards adjacents.....30

Reinstallation de la grille de la base ........................................... 31

Achever I'installation .................................................................. 31

REFRIGERATORDRAWERSSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

ProperDisposalofYourOld RefrigeratedAppliance

Before YouThrow Away Your Old Refrigerated Appliance:

Removethe door or drawer(s).

Suffocation Hazard

Remove door or drawer(s) from your old refrigerated appliance.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the past. A junked or abandoned refrigerated appliance is still dangerous - even if it will sit for "just a few days." Ifyou are getting rid of your old refrigerated appliance, please follow these instructions to help prevent accidents.

DESIGNSPECIFICATIONS

Models - Refrigerator Drawers

Style 1: Standard

Features wrap-around styling that complements the contoured door handles. This style provides warm, commercial-looking refrigerator drawers.

JUD278DBES00

Style 2: Overlay

Features factory-installed, overlay style trim to provide a "frameless" look. This style requires the installation of custom panels and handles.

JUD278DBCX00

INSTALLATIONREQUIREMENTS

s c nd

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here.

• Hand drill or electric drill • Tape measure (properly grounded) • Level

• r/8"Drill bit

• %6" Socket wrench

• 6" Socket extension (optional)

Additional Tools Needed for Style 2: Overlay (only):

• Scissors • Scribe

• Pencil

PARTS NEEDED Style 2: Overlay (only):

• Custom Overlay Drawer Panels -- See "Style 2: Custom Overlay Drawer Panels."

Hardware #8 x 1/2"Pan-head screws (12) optional

PARTS SUPPLIED:

• #8 x 1/2"Pan-head screws (16)

• Double-sided tape

If you plan to install custom wood panels, you will need to create the panels yourself or consult a qualified cabinetmaker or

carpenter, See dimension drawings for panel specifications,

IMPORTANT:

• The thickness of the overlay panels must be 3/4"(19.05 mm).

• Toavoid damage to the drawers, each overlay panel must not weigh more than 10 Ibs (4.5 kg).

• Do not exceed the height dimension for the overlay panels. Panels that exceed the height dimension may damage the refrigerator drawers, cabinets or countertop.

• The width of the overlay panels may vary according to the width of the cabinet opening.

• Phillips screwdriver

• T30 TORX_tscrewdriver

• Mounting Brackets (4)

Top Overlay Drawer Panel Dimensions

26.5"

1.25"

(3.2 cm) T

10.5"

(26.7 cm)

.........................

(67.4 cm)

12.7"

(32,2 cm)

235

(59.7 cm) 1.5"

(3.8 cm)

Bottom Overlay Drawer Panel Dimensions

26.5"

7/8"

(67,4 cm)

(22°m'T........................T

14.5" 16.5"

(36,8 cm) (42.0 cm)

23.5,,

(59,7 cm) 1.5"

(3.8 cm)

Flat Panels

You can create a custom flat panel using material less than %" (19.05 mm) thick. The material must be laminated to either plywood or medium density fiberboard that is %" (19.05 mm)

thick.

Raised Panels

You can create a raised panel design. Be sure to maintain a %" (19.05 mm) minimum thickness where the overlay panel attaches

to the drawer front.

1-®TORX is a registered trademark of Textron Innovations Inc.

Raised Panel Attachment

2. Center the custom hardware (left to right) onto the overlay

panel. When installing the custom hardware, be sure that the mounting screws are flush with the back of the overlay panels.

3. Repeat the process for the other overlay panel.

A. Drawer front B. #8 x _" pan-head screw

C. Overlay panel

Drawer Front #8 x 1/2"Pan-head Screw Locations

r,_

............ i

)

.... A

Styles 1 and 2: Standard and Overlay

• Height dimensions are shown with the leveling legs extended to V4" (6.35 mm) below the refrigerator drawers.

• When leveling legs are fully extended to 1" (25 mm) below the refrigerator drawers, add 3/4"(19.05 mm) to the height

dimensions.

• The power cord is 60" (152.4 cm) long.

26.7"

(67.9 cm)

23.5" 34.0"

(59.6 cm) cm)

Drawer Opening Dimensions

Dimensions vary based on model, asshown.

A. Pre-drilled screw locations

Hardware Installation (optional)

Customer supplied handles (hardware) may be installed at this time.

1. Measure and mark a line 3" (7.62 cm) down from the top of the overlay panel as shown.

IMPORTANT: Install hardware a minimum of 3" (7.62 cm) down from the top of the overlay panel. The space at the top of the panel is needed in order to attach the overlay panel to

the drawer front.

A. 3" (7.62 cm) area

A. Style 1: Standard

B. Style 2: Overlay--Measurement

does net include ¾" (19.05 mm) overlay panel or optional hardware

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator drawer(s). Failure to de so can result in death, explosion, or fire.

NOTES:

• For the refrigerator drawers to be flush with the front of the base cabinets remove any baseboards or moldings from the rear of the opening. See "Product Dimensions" and later in this section "Opening Dimensions (both styles)."

• It is recommended that you do not install the refrigerator drawers near an oven, radiator, or other heat source.

• Do not install in a location where the temperature will fall below 55°F (13°C).

Opening Dimensions (both styles}

• Height dimensions are shown with the leveling legs extended to the minimum height of V4"(6.35 mm) below the refrigerator

drawers. NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator drawers, add 3/4"(19.05 mm) to the height dimensions. See "Product Dimensions."

• If the floor of the opening is not level with the kitchen floor, shim the opening to make it level with the kitchen floor.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong. Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator drawers into the final location, it is important to make sure you have the proper electrical

connection.

Recommended grounding method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator drawers be provided. Use an outlet that cannot be turned off by a switch. Do not use an

extension cord. IMPORTANT: Ifthis product is connected to a GFCI

(Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

INSTALLATIONINSTRUCTIONS

'.5cm)

I I

35"

(88,9cm)

Use two or more people to move and install refrigerator drawer(s).

Failure to do so can result in back or other injury.

Remove the Packaging

Properly dispose of packaging. Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your

refrigerator drawers.

Excessive Weight Hazard

Remove the Skids

IMPORTANT:

• Always lay the appliance on its side when removing the skids.

• Never place the appliance on its top. It may damage the compressor.

• Allow the appliance to sit on its rollers for 4 hours before plugging into an electrical outlet.

1. Using two or more people, lay the appliance on its side.

2. Using a T30 TORX ®tscrewdriver, remove the skids from the bottom of the appliance. Discard the attachment bolts.

3. Using two or more people, turn the appliance upright on its rollers.

When Moving Your Refrigerator Drawers: Your refrigerator drawers are heavy. When moving the

appliance for service, be sure to protect the floor. Always pull the appliance straight out when moving it. Do not

wiggle or "walk" the appliance when trying to move it, as

floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of your refrigerator drawers before using them. See the cleaning

instructions in the Use & Care Guide.

If you have Style 1:Standard refrigerator drawers, skip this step. Go to "Attach the Mounting Brackets to Adjacent Cabinets" to

continue the installation.

IMPORTANT:

• Create custom overlay drawer panels according to the specifications in the "Style 2: Custom Overlay Drawer

Panels" section.

• Jenn-Air is not responsible for the removal or addition of molding or decorative panels that would not allow access to the refrigerator drawers for service.

Remove the Wire Baskets

1. Open the drawer to full extension and remove all articles from the wire baskets.

2. Pull the wire baskets out to full extension and lift out to remove.

IMPORTANT: You must remove the base grille in order to lower the leveling legs. Be sure to reinstall the base grille when the installation is complete.

1. Using a Phillips screwdriver, remove the four screws from the base grille as shown.

NOTE: Do not discard the screws.

A.Screws

Place the base grille on a clean, soft working surface for later use.

A. Wire baskets

3. Repeat the process for the other drawer.

Remove the Gaskets

IMPORTANT: The gaskets contain strong magnetic strips. Follow

these instructions and keep screws and other loose metal parts away from the gaskets to avoid damaging them.

1. Begin at the top right corner. Slowly pull the gasket out of the corner and continue working slowly toward the opposite side

as shown.

1-®TORX is a registered trademark of Textron Innovations Inc.

2. Proceed slowly from corner to corner until the gasket is completely free from the groove.

3. Gently push the gasket to the back of the drawer. Be sure to keep all screws and loose metal parts away from the magnetic gasket as shown.

Using a Phillips screwdriver, remove the wiring plug cover for the upper drawer as shown. Do not discard the screw or

cover. Set them aside for later use. NOTE: Removing the wiring plug cover will allow for easier

access when drilling and attaching the drawer front to the overlay panel. Be sure to replace the wiring plug cover when installation is complete.

A B

A. Drawer front B. Gasket

4. Repeat the process for the other gasket.

Install the Custom Overlay Panels

IMPORTANT:

• Before installing the custom overlay panels, be sure to install any custom hardware. See "Hardware Installation (optional)."

• Be sure to maintain a 3/8"(9.52 ram) gap between the overlay panel (top drawer) and the bottom of the kitchen cabinet.

1. Using a Phillips screwdriver or scribe, remove any residual foam from the pre-drilled pilot holes.

A ....

..... A

A. Wiring plug cover B. Screw

Remove the backing from the double-sided tape. Install the overlay panel to the drawer front. Be sure to align all edges of the drawer front to the overlay panel. Be sure that the overlay panel is level.

NOTE: The tape will secure the panel in place while drilling the pilot holes.

A. Double-sided tape

A. Pre-drilled pilot holes

Using the pre-drilled holes in the drawer front as a guide, use a scribe to mark the drilling locations on the overlay panel. Drill six 1/s"diam. x 1/2"deep (3.18 mm x 12.7 mm) holes into the overlay panel.

IMPORTANT: Do not drill deeper than 1/2"(12.7 mm).

Drive six #8 x 1/2"pan-head screws through the drawer front into the overlay panel.

Be sure that the overlay panels are flush with the bottom of the drawer fronts.

Top Drawer

A. Overlay panel B. Drawer front

Bottom Drawer

7. Repeat the process for the other drawer front.

8. Using a Phillips screwdriver, reinstall the wiring plug cover (upper drawer).

Reinstall the Gaskets

1. Starting at the corners, and working toward the opposite corner, press the gasket back into the groove. Be sure to seat the gasket on all four sides.

2. Repeat the process for the other drawer.

Install the Wire Baskets

Reinstall the wire baskets. See "Remove the Wire Baskets," earlier in this section.

IM PO RTANT:

• Install two mounting brackets (upper and lower) on both sides of the refrigerator drawers cabinet. The mounting brackets secure the appliance to the adjacent cabinets.

• To avoid the appliance pulling out of the opening when the drawers are opened, secure the mounting brackets to the adjacent cabinets.

• The mounting bracket has an offset. Be sure when installing the mounting brackets to position the offset to the adjacent

cabinets.

Begin installation (on each side) at the pre-drilled holes for the upper mounting brackets.

NOTE: Insulation tape covers the top pre-drilled holes for the upper mounting brackets. Do not remove the insulation tape when installing the upper mounting brackets.

A. Pre-drilled top hole is

underneath the insulation tape

B. Pre-drilled holes

2. Using a Phillips screwdriver and one #8 x W' pan-head screw, drive the screw through the bottom hole of upper mounting bracket and into the pre-drilled hole. Tighten the

screw.

3. Push a pan-head screw through the insulation tape and into the pre-drilled hole. Tighten the screw.

4. Using a Phillips screwdriver and two #8 x W' pan-head screws, drive the screws through the holes in the lower mounting bracket into the pre-drilled holes. Tighten the

screws.

5. Repeat the process for the other side.

6. Set aside the remaining eight #8 x W' pan-head screws for later use. See "Attach the Mounting Brackets to Adjacent

Cabinets."

IMPORTANT:

• To avoid floor damage, make sure the levelers are raised (not touching floor) and the weight of the appliance is on the rollers before moving.

• Rollers are for moving the refrigerator drawers and not for permanent support.

1. Place top of cardboard carton or plywood under the appliance. Remove dolly.

2. Do not remove protective film or cover.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

3. Plug into a grounded 3 prong outlet.

4. Move the refrigerator drawers straight back and evenly in

front of the opening.

Using a %6" socket wrench (and extension if necessary), turn the leveling bolts on both sides of the refrigerator drawers to the right (clockwise) until the leveling legs support the refrigerator drawers' weight.

A. Rear leveling bolt

B. Front leveling bolt

Lower all four leveling legs until the refrigerator drawers are the proper height.

IMPORTANT:

• Style 2qDverlay: Be sure to install the custom overlay drawer panels before leveling the refrigerator drawers for the Overlay Model. See "Style 2: Install Custom Overlay Drawer Panels."

• Before installing the refrigerator drawers, be sure that the countertop is level.

If the countertop is not level, adjust the refrigerator drawers' front and rear leveling bolts until the appliance is square with the countertop. Be sure to maintain %" (9.5 mm) minimum gap between the top of the drawer and the countertop.

1. Open the top drawer and place the level across the top drawer as shown. Check the level from left to right.

IMPORTANT:

• All four leveling legs must contact the floor to support and stabilize the full weight of the refrigerator drawers.

• Rollers are for moving the refrigerator drawers and not for permanent support.

• Toavoid cabinet/countertop damage, do not apply more than 50 inch-pounds (58 cm - kg) of torque to the leveling legs.

• When leveling, be sure that the gap between the upper drawer and the bottom edge of the countertop is a minimum of %" (9.5 mm).

• Style 2: Overlay-- Be sure to install the custom overlay drawer panels before leveling the refrigerator drawers. See "Style 2:

Install Custom Overlay Drawer Panels."

A.Check the level from left to right.

Using the front and rear leveling bolts, adjust the refrigerator drawers cabinet until the top drawer measures level from left to right. See "Lower Leveling Legs."

NOTE: Adjusting the front and rear leveling bolts together will either raise or lower the side of the refrigerator drawers

cabinet.

Remove the level and close the top drawer. Check the gap between the top of the drawer and the countertop. If the gap measures less than %" (9.5 mm) minimum, turn all four leveling bolts equally to the left to raise the leveling legs (this will lower the appliance). Recheck the level.

+ 22 hidden pages