Jenn-Air KDDO24CVX00, KDDC24RVS00, KDDC24CVX01, KDDC24CVS01, JUD248RWRS00 Owner’s Manual
...
JENN-AIRo
DOUBLE REFRIGERATOR DRAWERS
REFRIGERATOR/FREEZER DRAWERS
DOUBLE FREEZER DRAWERS
For questions about features, operation/performance, parts, accessories, or service, call: 1-800-688-1100 or visit our website at...
In Canada, call: 1-800-807-6777, or visit our website at...
p
www.jennair.com
www.jennair.ca
CAJON REFRIGERADO DOBLE
CAJONES REFRIGERADOS/CONGELADOS
CAJONES CONGELADOS DOBLES
Para consultas respecto a caracteristicas, operaci6n/desempefio, partes, accesorios o servicio, Ilame al: 1-800-688-100
o visite nuestra p&gina de internet...
www.jennair.com
En Canad&, lame al: 1-800-807-6777 o visite nuestra p&gina de internet..
www, jennair, ca
p p p
DDOUBLE TIROIR REFRIGERE
p p p
TIROIRS DE REFRIGERATION/CONGELATION
p
DOUBLE TIROIR DE CONGELATION
k,yllI]. _,_:_UtllL_,_,d(,l= ° =' " "'
Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web &...
www, jennair, ca
Table of Contents/Jndice/Table des matieres .................................................................. 2
W10130023A
TABLEOF CONTENTS
REFRIGERATOR DRAWERS SAFETY .......................................... 3
Proper Disposal of Your Old Refrigerated Appliance .................. 3
DESIGN SPECIFICATIONS ............................................................ 4
24" Drawer Models ...................................................................... 4
INSTALLATION REQUIREMENTS ................................................ 5
Tools and Parts ............................................................................ 5
Location Requirements ................................................................ 5
Electrical Requirements ............................................................... 5
Water Supply Requirements ........................................................ 6
Product Dimensions ..................................................................... 6
Style 2: Custom Overlay Drawer Panels ...................................... 7
INSTALLATION INSTRUCTIONS .................................................. 8
Unpack the Refrigerator Drawers ................................................ 8
Connect Water Supply ................................................................. 8
Move the Refrigerator Drawers to Final Location ........................ 9
Level the Refrigerator Drawers .................................................... 9
Install Custom Overlay Panel ..................................................... 10
Water Filtration System .............................................................. 10
Complete Installation ................................................................. 10
[NDICE
SEGURIDAD DE LOS CAJONES REFRIGERADOS .................. 20
Como deshacerse adecuadamente
de su aparato refrigerado viejo .................................................. 20
ESPECIFICACIONES DE DISEI_IO .............................................. 21
Modelos de cajon de 24". .......................................................... 21
REQUlSITOS DE INSTALACION ................................................. 22
Piezas y herramientas ................................................................ 22
Requisitos de ubicacion ............................................................. 22
Requisitos electricos .................................................................. 22
Requisitos del suministro de agua ............................................. 23
Medidas del producto ................................................................ 23
Estilo 2: Paneles de los cajones recubiertos a la medida ......... 24
INSTRUCCIONES DE INSTALACION ......................................... 25
Como desempacar los cajones refrigerados ............................. 25
Conexion del suministro de agua .............................................. 25
Mueva los cajones refrigerados a su posicion final ................... 26
Nivelacion de los cajones refrigerados ...................................... 26
Como instalar el panel recubierto a la medida .......................... 27
Sistema de filtracion de agua .................................................... 27
BEFORE USE ................................................................................ 10
REFRIGERATOR DRAWERS USE .............................................. 11
Normal Sounds ........................................................................... 11
Ensuring Proper Air Circulation .................................................. 11
Using the Controls ...................................................................... 11
Ice Maker and Water Filtration System ...................................... 13
REFRIGERATOR DRAWERS CARE ............................................ 14
Cleaning ...................................................................................... 14
Power Interruptions.................................................................... 14
Vacation Care ............................................................................. 14
TROUBLESHOOTING .................................................................. 15
ASSISTANCE OR SERVICE ......................................................... 16
In the U.S.A ................................................................................ 16
In Canada ................................................................................... 16
Accessories ................................................................................ 17
WATER FILTER CERTIFICATIONS ............................................. 17
PRODUCT DATA SHEETS ........................................................... 18
WAR RANTY .................................................................................. 19
Complete la instalacion .............................................................. 27
ANTES DEL USO .......................................................................... 28
USO DE LOS CAJONES REFRIGERADOS ................................ 28
Sonidos normales ....................................................................... 28
Como asegurar la debida circulacion de aire ............................ 28
Uso de los controles .................................................................. 28
Fabrica de hielo y sistema de filtracion de agua ....................... 30
CUlDADO DE LOS CAJONES REFRIGERADOS ....................... 31
Limpieza ..................................................................................... 31
Cortes de corriente ..................................................................... 31
Cuidado durante las vacaciones ................................................ 32
SOLUCION DE PROBLEMAS ...................................................... 32
AYUDA O SERVICIO TI_CNICO ................................................... 34
En los EE.UU .............................................................................. 34
En Canada .................................................................................. 34
Accesorios .................................................................................. 34
HOJA DE DATOS DEL PRODUCTO ........................................... 35
GARANTiA ..................................................................................... 36
TABLEDESMATIERES
SI_CURITI_ DES TIROIRS RI_FRIGI_RI_S .................................... 37
Mise au rebut correcte de votre vieil appareil refriger6 ............. 37
SPI_CIFICATIONS DE DESIGN .................................................... 38
Modeles de tiroirs de 24". ......................................................... 38
EXIGENCES D'INSTALLATION ................................................... 39
Outillage et pieces ...................................................................... 39
Exigences d'emplacement ......................................................... 39
Specifications electriques .......................................................... 39
Specifications de I'alimentation en eau ..................................... 40
Dimensions du produit ............................................................... 40
Style 2 : Panneaux decoratifs de tiroirs personnalises ............. 41
INSTRUCTIONS D'INSTALLATION ............................................ 42
Deballage des tiroirs refrigeres .................................................. 42
Raccordement de I'alimentation en eau.................................... 42
Deplacement des tiroirs refrigeres A leur emplacement final....43
Reglage de I'aplomb des tiroirs refrigeres ................................. 43
Installation du panneau decoratif personnalise ......................... 43
Systeme de filtration de I'eau..................................................... 44
2
Achever I'installation .................................................................. 44
AVANT L'UTILISATION ................................................................ 44
UTILISATION DES TIROIRS RI_FRIGI_RI_S................................ 45
Sons normaux ............................................................................ 45
Pour assurer une circulation d'air correcte ................................ 45
Utilisation des commandes ........................................................ 45
Machine A gla£;ons et systeme de filtration d'eau ..................... 47
ENTRETIEN DES TIROIRS RI_FRIGI_RI_S .................................. 48
Nettoyage ................................................................................... 48
Pannes de courant ..................................................................... 48
Entretien avant les vacances ..................................................... 48
DI_PAN NAGE................................................................................. 49
ASSISTANCE OU SERVICE ......................................................... 50
Aux €:tats-Unis ............................................................................ 50
Au Canada .................................................................................. 50
Accessoires ................................................................................ 50
FEUlLLES DE DONNI_ES SUR LE PRODUlT ............................. 51
GARANTIE ..................................................................................... 52
REFRIGERATORDRAWERSSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator drawer(s), follow these basic
precautions:
• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Disconnect power before servicing.
• Replace all parts and panels before operating.
SAVE THESE INSTRUCTIONS
• Remove door or drawer(s) from your old refrigerated
appliance.
• Use nonflammable cleaner.
• Keep flammable materials and vapors, such as gasoline,
away from refrigerator drawer(s).
• Use two or more people to move and install refrigerator
drawer(s).
Proper Disposal of Your Old
Refrigerated Appliance
Suffocation Hazard
Remove door or drawer(s) from your old refrigerated
appliance.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems
of the past. A junked or abandoned refrigerated appliance is still
dangerous - even if it will sit for "just a few days." If you are
getting rid of your old refrigerated appliance, please follow these
instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerated Appliance:
Removethe door or drawer(s).
DESIGNSPECIFICATIONS
Double Refrigerator Drawers
Two refrigerator drawers provide additional storage options in the kitchen or other areas of the home.
Euro Seriesl
JUD248RCRS
Refrigerator/Freezer Drawers (with ice maker and water filter)
Upper refrigerator drawer and lower freezer drawer provide additional storage options inthe kitchen or other areas of the home.
Factory-installed ice maker in lower drawer ensures a constant supply of ice on hand at all times.
Euro Series
JUD248CCRS
Double Freezer Drawers (with ice maker and water filter)
Two freezer drawers provide additional storage options in the kitchen or other areas of the home. Factory-installed ice maker in
lower drawer ensures a constant supply of ice on hand at all times.
Overlay - Custom Panels and Handles Required
JU D248 RCCX
Overlay - Custom Panels and Handles Required
JUD248CCCX
Euro Series
JUD248FCRS
Overlay - Custom Panels and Handles Required
JU D248FCCX
INSTALLATIONREQUIREMENTS
TOOLS NEEDED:
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
• Cordless drill
• 1/8"Drill bit
Additional Tools Needed for Style 2: Overlay (only):
• Scissors • Scribe
• Pencil
PARTS NEEDED Style 2: Overlay (only):
• Custom Overlay Drawer Panels --
See "Style 2: Custom Overlay Drawer Panels."
• Hardware
• Tape measure
• Level
• Phillips screwdriver
NOTE: When leveling legs are fully extended to 1" (25 mm)
below the refrigerator drawers, add 3/4"(19.05 mm) to the
height dimensions. See "Product Dimensions."
If the floor of the opening is not level with the kitchen floor,
shim the opening to make it level with the kitchen floor.
.......................A 343/8" (87.3 cm) min.
35" (88.9 cm) max.
PARTS SUPPLIED:
• Hooks (8)
• Overlay plates (4)
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator drawer(s).
Failure to do so can result in death, explosion, or fire.
NOTES:
• For the refrigerator drawers to be flush with the front of the
base cabinets remove any baseboards or moldings from the
rear of the opening. See "Product Dimensions" and later in
this section "Opening Dimensions (both styles)."
• It is recommended that you do not install the refrigerator
drawers near an oven, radiator, or other heat source.
• Do not install in a location where the temperature will fall
below 55°F (13°C).
Opening Dimensions (both styles)
• Height dimensions are shown with the leveling legs extended
to the minimum height of 1/4"(6.35 mm) below the refrigerator
drawers.
• Screws (16)
0.96 cm) b--
rnin.
24" (60.96 cm) min.
Critical Dimensions:
A. 14_" (37.5 cm) utility opening
B. 24" (60.96 cm) minimum opening width
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your refrigerator drawers into the final location,
it is important to make sure you have the proper electrical
connection.
Recommended grounding method
A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded
electrical supply is required. It is recommended that a separate
circuit serving only your refrigerator drawers be provided. Use an
outlet that cannot be turned off by a switch. Do not use an
extension cord.
B
i
r\
I"®TORX is a registered trademark of Textron Innovations Inc.
IMPORTANT: If this product is connected to a GFCI
(Ground Fault Circuit Interrupter) equipped outlet, nuisance
tripping of the power supply may occur, resulting in loss of
cooling. Food quality and flavor may be affected. If nuisance
tripping has occurred, and if the condition of the food appears
poor, dispose of it.
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
IMPORTANT:
• If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF.
• All installations must meet local plumbing code requirements.
• Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
TOOLS NEEDED: Flat-blade screwdriver, 7/le" and 1/2"open-end
wrenches or two adjustable wrenches, 1/4"nut driver and drill bit,
cordless drill.
NOTE: Your refrigerator dealer has a kit available with a 1/4"
(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.
Before purchasing, make sure a saddle-type valve complies with
your local plumbing codes. Do not use a piercing-type or 3Ad'
(4.76 mm) saddle valve which reduces water flow and clogs more
easily.
P C< S SCD me,is
Styles 1 and 2: Euro Series and Overlay
• Height dimensions are shown with the leveling legs extended
to 1/4"(6.35 mm) below the refrigerator drawers.
• When leveling legs are fully extended to 1" (25 mm) below the
refrigerator drawers, add 3/4"(19.05 mm) to the height
dimensions.
• The power cord is 60" (152.4 cm) long
Style 1: Euro Series
(
%,,_{_
(1.0 cm) T '
/
( )
Water Pressure
A cold water supply with water pressure of between 30 and
120 psi (207 and 827 kPa) is required to operate ice maker. If you
have questions about your water pressure, call a licensed,
qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi
(207 and 827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).
If the water pressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.
• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Style 2: Overlay
(1.0 cm) T
m
t
147/8''
(37.8 cm)
147/8''
(37.8cm)
(88.7 cm)
341/8,'
6
Drawer Opening Dimensions
Drawer Width Dimensions
Dimensions vary based on model, asshown.
Style 1: Euro Series
21 "
(53.3 cm)
18%6"
(47.2 cm)
221/2"
(57.2 cm)
oo
° °°
oo
oo
Style 2: Overlay
_._ 171/4" I_
(43.8 cm) v I
oo
F
.-I
221/2''
(57.2 cm)
Style 1: Euro Series
235/8''
(60.0 cm)
/
24
(60.z
cm)
271/8''
(68.9 cm)
233/4''
(60.4 cm)
Style 2: Overlay
O0 O0
O0 O0
oo
oo
(51
I cm)/
241/8"
(61.2 cm)
233/4''
(60.4 cm)
If you plan to install custom wood panels, you will need to create
the panels yourself or consult a qualified cabinetmaker or
carpenter. See dimension drawings for panel specifications.
IMPORTANT:
• The thickness of the overlay panels must be 3/4"(19.05 mm).
• To avoid damage to the drawers, each overlay panel must not
weigh more than 10 Ibs (4.5 kg).
• Do not exceed the height dimension for the overlay panels.
Panels that exceed the height dimension may damage the
refrigerator drawers, cabinets or countertop.
• The width of the overlay panels may vary according to the
width of the cabinet opening.
Topand Bottom Overlay Drawer Panel Dimensions
235/8"
(60.0 cm)
41/8 ''
(10.5 cm)
13/16"
(2.1 cm)
147/8"
(37.6 cm)
cm)
Reverse Side
,k
Pilot Holes
1/16"(1.6 mm) diameter x
3/8"(9.5 mm) deep
8 places
A. Overlay hook locations
B. Route _" deep
INSTALLATIONINSTRUCTIONS
Connect to Water Line
1. Unplug refrigerator or disconnect power.
2. Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Locate a 1/2"to 1V4"(1.25 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IM PORTANT:
• Make sure it is a cold water pipe.
• Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and normal sediment from collecting in the valve.
4.
Determine the length of copper tubing you need. Measure
from the connection on the lower left rear of refrigerator to the
water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use V4"
(6.35 mm) O.D. (outside diameter) copper tubing. Be sure
both ends of copper tubing are cut square.
5.
Using a grounded drill, drill a V4"hole in the cold water pipe
you have selected.
Excessive Weight Hazard
Use two or more people to move and install
refrigerator drawer(s).
Failure to do so can result in back or other injury.
Remove the Packaging
Properly dispose of packaging. Do not use sharp instruments,
rubbing alcohol, flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the surface of your
refrigerator drawers.
When IVlovingYour Refrigerator Drawers:
Your refrigerator drawers are heavy. When moving the
appliance for service, be sure to cover the floor with
cardboard or hardboard to avoid floor damage. Always pull
the appliance straight out when moving it. Do not wiggle or
"walk" the appliance when trying to move it, as floor
damage could occur.
Clean Before Using
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the V4" drilled hole
in the water pipe and that the washer is under the pipe clamp.
Tighten the packing nut. Tighten the pipe clamp screws
slowly and evenly so washer makes a watertight seal. Do not
overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten.
8. Place the free end of the tubing in a container or sink, and
turn ON the main water supply. Flush the tubing until water is
clear. Turn OFF the shutoff valve on the water pipe. Coil the
copper tubing.
Connect to Refrigerator
1. Attach the copper tube to the valve inlet using a compression
nut and sleeve as shown. Tighten the compression nut. Do
not overtighten. Use the tube clamp on the back of the
refrigerator to secure the tubing to the refrigerator as shown.
This will help avoid damage to the tubing when the
refrigerator is pushed back against the wall.
2. Turn shutoff valve ON.
E. Compression sleeve
F. Shutoff valve
G. Packing nut
After you remove all of the package materials, clean the inside of
your refrigerator drawers before using them. See the cleaning
instructions in the Use & Care Guide.
8
3=
Check for leaks. Tighten any connections (including
connections at the valve) or nuts that leak.
Q
A. Plug
B. Compression nut
C. Pex tubing
4. The ice maker is equipped with a built-in water strainer. If
your water conditions require a second water strainer, install
it in the 1/4"(6.35 mm) water line at either tube connection.
Obtain a water strainer from your nearest appliance dealer.
5. Plug in refrigerator or reconnect power.
IMPORTANT:
• Style 2-Overlay: Be sure to install the custom overlay drawer
panels before leveling the refrigerator drawers for the Overlay
Model. See "Style 2: Install Custom Overlay Drawer Panels."
• Before installing the refrigerator drawers, be sure that the
countertop is level.
• If the countertop is not level, adjust the refrigerator drawers'
leveling legs until the appliance is square with the countertop.
Be sure to maintain 3/8"(9.5 mm) minimum gap between the
top of the drawer and the countertop.
1. Open the top drawer and place the level across the top
drawer as shown. Check the level from left to right.
1. Place top of cardboard carton or plywood under the
appliance. Remove dolly.
2. Do not remove film or cover.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
3. Plug into a grounded 3 prong outlet.
4. Move the refrigerator drawers straight back and evenly in
front of the opening.
A. Check the level from left to righL
2. Turn the leveling legs (front and back) until the top drawer
measures level from left to right.
3. Remove the level and close the top drawer. Check the gap
between the top of the drawer and the countertop. If the gap
measures less than 3/8"(9.5 mm) minimum, turn all four
leveling bolts equally to the left to raise the leveling legs (this
will lower the appliance). Recheck the level.
4. Open both drawers less than midway. Place the level on the
side flange beside the drawers as shown. Turn the front
leveling bolts together in order to either raise or lower the
appliance until the sides of the refrigerator drawers are
plumb.
A
A. Check thelevel
from front toback.
5.
Remove the level and close the drawers. Recheck the gap
between the top of the drawer and the countertop. If the gap
measures less than 3/8"(9.5 mm), turn all four leveling bolts
equally to raise the leveling legs (this will lower the appliance).
Recheck the level.
NOTE: Be sure to recheck the horizontal level of the top
drawer.
6.
Be sure all four levelers are on the floor and supporting the
full weight of the refrigerator drawers.
IM PORTANT:
• Create custom overlay panel according to the specifications
in the "Custom Overlay Panel" section.
• Jenn-Air is not responsible for the removal or addition of
molding or decorative panels that would not allow access to
the refrigerator for service.
Attach the Overlay Panel
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.
Water Filter Status Light (on some models)
The water filter status light will help you know when to change
your water filter. The light will change from dark to yellow. This
tells you that it is almost time to change the filter. It is
recommended that you replace the water filter when the status
light changes to red OR water flow to your ice maker decreases
noticeably. The filter should be replaced at least every 6 months
depending on your water quality and usage.
After changing the water filter, reset the water filter status light.
The status light will change from red to dark when the system is
reset.
NOTE: If the overlay hooks are not installed, see "Custom
Overlay Panel" for overlay hook locations.
1. Position the overlay panel V2"(1.27 cm) higher than the door.
Be sure to position the overlay hooks to the pilot holes.
1U,.,...]
_i ¸ !
2. Insert the overlay hooks into the top of the holes in the door.
Push against the overlay panel to force the overlay hooks
deeper into the door. Pull the overlay panel straight down to
secure the overlay hooks to the door.
3. Using a Phillips screwdriver, attach the overlay plates to the
bottom of the overlay panel and door as shown.
Using the Ice Maker Without the Water Filter
You can run the ice maker without a water filter. Your water will
not be filtered.
1. Remove the water filter.
2. Slide the cap off the end of the filter and replace the cap in
the base grille.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
1. Remove all boxes, parts packages and packing materials
from the interior of the refrigerator drawers.
2. Remove the film.
3. Clean the refrigerator drawers before use.
4. The controls are preset at the factory to the recommended
settings. Be sure that the compressor is operating properly
and that all the lights are working.
5. If construction will continue after the refrigerator drawers
have been installed, turn the power Off for both Drawers.
To get the most efficient use from your new refrigerator drawers,
read the "Refrigerator Drawers Use" section.
BEFOREUSE
10
A B C D
A. Overlay panel
B. Door
C. Overlay plates (2)
D. Round-head screws (8)
Remove the Packaging
• Remove tape and glue residue from surfaces before turning
on the refrigerator drawers. Rub a small amount of liquid dish
soap over the glue residue with your fingers. Wipe with warm
water and dry.
• Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator
drawers. For more information, see "Refrigerator Drawers
Safety."
Clean Before Use
After you remove all of the packaging materials, clean the inside
of your refrigerator drawers before using them. See the cleaning
instructions in "Refrigerator Drawers Care."
REFRIGERATORDRAWERSUSE
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Your new refrigerator drawers may make sounds that your old
refrigerator drawers didn't. Because the sounds are new to you,
you might be concerned about them. Most of the new sounds are
normal. Hard surfaces, such as the floor, walls, and cabinets, can
make the sounds seem louder. The following describes the kinds
of sounds and what may be making them.
• Your refrigerator drawers are designed to run more efficiently
to keep your food items at the desired temperatures and to
minimize energy usage. The high efficiency compressor and
fans may cause your refrigerator drawers to run longer than
your old ones. You may also hear a pulsating or high-pitched
sound from the compressor or fans adjusting to optimize
performance.
• You may hear the evaporator fan motor circulating air through
the refrigerator drawers. The fan speed may increase as you
open the drawers or add warm food.
• As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing through the sealed system tubing.
• Contraction and expansion of the inside walls may cause a
popping noise.
• You may hear air being forced over the condenser by the
condenser fan.
• You may hear water running into the drain pan during the Off
cycle.
J g P ;}pe C @
In order to ensure proper temperatures, you need to permit
airflow inside the drawers.
Do not block any airflow vents. If the vents are blocked, airflow
will be obstructed and temperature and moisture problems may
occur.
IMPORTANT: To avoid odor transfer and drying out of food, wrap
or cover foods tightly.
_ C_,
The control panels for both refrigerator drawers are located in the
upper drawer. To view and set the Upper and Lower control
panel, pull out the upper drawer.
IMPORTANT:
• Wait 24 hours after you turn on the refrigerator drawers
before you put food into the drawers. If you add food before
the drawers have cooled completely, your food may spoil.
NOTE: Adjusting the controls to a lower (colder) setting in
one or both drawers will not cool them any faster.
• If the temperature is too warm or too cold inthe drawers, first
check the air vents to be sure they are not blocked before
adjusting the controls.
• The preset settings should be correct for normal household
usage. The refrigerator control is set correctly when milk or
juice is as cold as you like.
• The freezer control is set correctly when ice cream is firm.
• The actual temperature may differ from the display when a
drawer is open for an extended period of time.
Turning Drawers On/Off
• Press and hold Cooling On for 3 seconds to the drawers on.
The indicator light with light up.
• Press and hold Cooling On for 3 seconds to turn the drawers
off.
Viewing Celsius Temperatures
• Press the °C touch pad to change the temperature display
information from Fahrenheit to Celsius. The indicator will light
up.
ffi
• To redisplay degree Fahrenheit, press °C touch pad again.
Set to Recommended Temperatures
Press the Set touch pad to reset the set points to the factory
recommended temperatures.
The recommended temperatures setting for the refrigerator
drawer is 37°F (3°C). The recommended temperature setting
for the freezer drawer is 0°F (-18°C).
11
Adjusting Temperature Set Points
Style 1: Double Refrigerator Drawers
The refrigerator control adjusts the temperature in both upper
and lower drawers.
Style 2: Refrigerator/Freezer Drawers
The refrigerator control adjusts the temperature in the upper
drawer. The freezer control adjusts the temperature of the lower
drawer.
Style 1: Double Refrigerator Drawers
Max Cool will reset the temperature for both drawers to the
coldest setting 34°F (0.5°C) for 24 hours.
Style 2: Refrigerator/Freezer Drawers
Max Cool will reset the temperature for both drawers to the
coldest setting 34°F (0.5°C) in the refrigerator drawer and -5°F
(-20.5°C) in the freezer drawer for 24 hours.
Style 3: Double Freezer Drawers
Max Freeze will reset the temperatures for both drawers to the
coldest setting -5°F (-20.5°C) for 24 hours.
NOTE: The temperature display will remain at the coldest
setting(s) and the indicator light will remain on for 24 hours. After
24 hours, the drawer will return to the previous temperature set
point(s) and the indicator light will turn off.
Sabbath Mode
Sabbath Mode is designed for the traveler or for those whose
religious observances require turning off the lights. By selecting
this feature, the temperature set points remain unchanged and
the interior lights will turn off. For most efficient refrigerator
drawers operation, it is recommended to exit the Sabbath Mode
when it is no longer required.
• Press and hold the Sabbath Mode touch pad for 3 seconds to
turn on the feature. The indicator will light up.
Style 3: Double Freezer Drawers
The freezer control adjusts the temperature in both upper and
lower drawers.
IMPORTANT: Wait at least 24 hours between adjustments.
Recheck the temperatures before other adjustments are made.
To adjust set point temperatures:
• Press the refrigerator or freezer PLUS (+) or MINUS (-) touch
pad until the desired temperature setting is reached.
NOTE: The set point range for the refrigerator drawer is 34°F
(1°C) to 45°F (7°C). The set point range for the freezer drawer
is -5°F (-20.5°0) to 5°F (-15°O).
Max Cool or Max Freeze
• Press and hold Sabbath Mode touch pad for 3 seconds to
turn the feature off.
Control Lock
The control panel can be locked to avoid unintentional
temperature changes by small children or during cleaning.
• Press and hold the Control Lock touch pad for 3 seconds to
turn on the feature. The indicator will light up.
• To deactivate the feature, press and hold Control Lock touch
pad for 3 seconds.
NOTE: When Control Lockout is activated, the control panel
touch pads will not work. Any attempt to change the settings will
result in a beep to indicate the control panel is locked.
Drawer Open/Alarm Reset
The Drawer Open alarm will sound and the Alarm Reset indicator
will light up when a drawer has been open for longer than
10 minutes.
The Max Cool or Max Freeze feature assists with periods of
heavy usage, full grocery loads or temporarily warm room
temperatures.
12
To temporarily disable the Drawer Open alarm, press and hold
the Alarm Reset touch pad for 3 seconds. Closing the drawer will
stop the audible alarm and reset the 10-minute timer.
Turning the Ice Maker On/Off
Changing the Water Filter Cartridge
IMPORTANT: Use the Ice On touch pad on the control panel to
turn the ice maker on or off. Do not adjust the wire arm located
on the ice maker.
• Press and hold the Ice On touch pad for 3 seconds to turn the
ice maker ON. The indicator will light up.
• Press and hold the Ice On touch pad for 3 seconds to turn the
ice maker OFR
NOTE:
• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
• The quality of your ice will only be as good as the quality of
the water supplied to your ice maker. Avoid connecting the
ice maker to a softened water supply. Water softener
chemicals (such as salt) can damage parts of the ice maker
and lead to poor quality ice. If a softened water supply cannot
be avoided, make sure the water softener is operating
properly and is well maintained.
• Do not store anything in the ice storage bin.
Water Filtration System
The water filter cartridge is located through the base grille. You
do not have to remove the base grille in order to change the
water filter cartridge.
1. Locate the water filter cartridge cap in the front base grille.
Rotate the cap counterclockwise to a vertical position and
pull the cap and filter cartridge out through the base grille.
NOTE: There will be water in the cartridge. Some spilling may
occur.
2,
Remove the cartridge cap by sliding it off the end of the old
cartridge. The cap will slide to the left or right.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
3. Take the new cartridge out of its packaging and remove cover
from O-rings.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.
Water Filter Indicator / Reset Filter
The water filter indicator will help you know when to change your
water filter cartridge. The indicator will change from dark to
yellow when it is time to order a new filter. The indicator will then
change from yellow to red when it is time to replace the filter
cartridge. The filter cartridge should be replaced at least every
6 months depending on your water quality and usage.
After replacing the water filter cartridge, reset the water filter
indicator.
• Press and hold the Reset Filter touch pad for 3 seconds. The
indicator light will turn from red to dark.
4,
Slide the cartridge cap onto the new cartridge. See
illustration in Step 2.
5.
With cartridge cap in the vertical position, push the new filter
cartridge into the base grille until it stops. Rotate the cartridge
cap clockwise to a horizontal position. Flush the water
system. See "Flushing the Water System After Replacing
Filter" later inthis section.
Using the Ice Maker Without the Water Filter
You can run the ice maker without a water filter cartridge. Your
water will not be filtered.
1. Slide the cartridge cap off the end of the filter cartridge. With
the cartridge cap in the horizontal position, insert the cap into
the base grille until it stops.
IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement filter.
13
REFRIGERATORDRAWERSCARE
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
The drawers defrost automatically. However, clean both drawers
about once a month to avoid buildup of odors. Wipe up spills
immediately.
To clean your refrigerator drawers:
1. Hand wash, rinse, and dry interior surfaces thoroughly. Use a
clean sponge or soft cloth and a mild detergent in warm
water.
• Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and drawer liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.
• To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt
[26 g to 0.95 L] of water).
2. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners. Dry thoroughly with a soft
cloth. To avoid damage to painted metal exteriors, apply
appliance wax (or auto paste wax) with a clean, soft cloth. Do
not wax plastic parts.
NOTE: To keep your Stainless Steel refrigerator drawers
looking like new and to remove minor scuffs or marks, it is
suggested that you use the manufacturer's approved
Stainless Steel Cleaner and Polish. To order the cleaner, see
"Accessories."
IMPORTANT: This cleaner is for Stainless Steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces or
drawer gaskets. If unintended contact does occur, clean
plastic part with a sponge and mild detergent in warm water.
Dry thoroughly with a soft cloth.
If the power will be out for 24 hours or less, keep both refrigerator
drawers closed to help food stay cold.
If the power will be out for more than 24 hours, do one of the
following:
• Place all perishable food in a food locker or cooler with dry
ice.
• If neither a food locker or cooler is available, consume food if
still cold or throw away perishable food at once.
Your refrigerator drawers are equipped with the Holiday Mode
feature. By selecting this feature, the temperature set points
remain unchanged and the interior lights will turn off. For most
efficient refrigerator drawers operation, it is recommended to exit
the Holiday Mode when it is no longer required.
If you choose to leave the refrigerator drawers on while
you're away:
1. Use up any perishables and freeze other items.
2. Press HOLIDAY MODE touch pad.
3. When you return from vacation, press HOLIDAY MODE touch
pad to return to normal operation.
If you choose to turn the refrigerator drawers off before
you leave:
1. Remove all food from the refrigerator drawers.
2. Turn the Control Panel for the Upper and the Lower drawers
to Off. See "Using the Controls."
3. Clean refrigerator drawers, wipe and dry them well.
4. Tape rubber or wood blocks to the tops of both drawers to
prop them open far enough for air to get in. This stops odor
and mold from building up.
14
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Your refrigerator drawers will not operate
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
• Is the power supply cord unplugged? Plug into a grounded
3 prong outlet.
• Has a household fuse blown, or a circuit breaker tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
• Are the refrigerator drawers control set in the Off
position? See "Using the Controls."
• Are the refrigerator drawers not cooling? Turn them off
then on again to reset. See "Using the Controls." If this does
not correct the problem, call for service.
The motor seems to run too much
• Is the room temperature hotter than normal? The motor
will run longer under warm conditions. At normal room
temperatures, expect your motor to run about 80% of the
time. Under warmer conditions, it will run even more.
Has a large amount of food just been added to the
refrigerator drawers? Adding a large amount of food warms
the refrigerator drawers. The motor normally will run longer to
cool the refrigerator drawers back down.
• Are the drawers opened often? The motor will run longer
when this occurs. Conserve energy by getting all items out at
one time, keeping food organized, and closing the drawer as
soon as possible.
• Are the controls not set correctly for the surrounding
conditions? See "Using the Controls."
• Are the drawers not closed completely? Close the drawers
firmly. If they do not close completely, see "The drawers will
not close completely" later in this section.
• Are the drawer gaskets not sealed all the way around?
Contact a technician or other qualified person.
The refrigerator drawers seems to make too much noise
The sounds may be normal for your refrigerator drawers. See
"Normal Sounds."
The divider between the two compartments is warm
The warmth is probably due to normal operation of the
automatic exterior moisture control. If still concerned, call for
service.
Temperature is too warm
• Are the air vents blocked in either compartment? This
obstructs cold air movement between the compartments.
Remove any objects from in front of the air vents. See
"Ensuring Proper Air Circulation" for the location of air vents.
• Are the drawers opened often? The refrigerator drawers will
warm when this occurs. Keep the refrigerator drawers cool by
getting all items out at one time, keeping food organized, and
closing the door as soon as possible.
• Has a large amount of food just been added to the
refrigerator drawers? Adding a large amount of food warms
the refrigerator drawers. It can take several hours for the
refrigerator drawers to return to the normal temperature.
• Are the controls set correctly for the surrounding
conditions? See "Using the Controls."
• Are the refrigerator drawers not cooling? Turn them off
then on again to reset. See "Using the Controls." If this does
not correct the problem, call for service.
15
There is interior moisture buildup
• Are the air vents blocked in the refrigerator drawers?
Remove any objects from in front of the air vents. See
"Ensuring Proper Air Circulation" for the location of air vents.
• Are the drawers opened often? Avoid humidity buildup by
getting all items out at one time, keeping food organized, and
closing the drawer as soon as possible.
• Is the room humid? It is normal for moisture to build up
inside the refrigerator drawers when the room air is humid.
• Is the food packaged correctly? Check that all food is
securely wrapped. Dry damp food containers before placing
in the refrigerator drawers.
• Are the controls set correctly for the surrounding
conditions? See "Using the Controls."
The drawers will not close completely
• Are food packages blocking the drawer open? Rearrange
containers so that they fit more tightly and take up less
space.
ASSISTANCEOR SERVICE
The drawers are difficult to open
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
• Are the gaskets dirty or sticky? Clean gaskets and the
surface that they touch. Rub a thin coat of paraffin wax on the
gaskets following cleaning.
Before calling for assistance or service, please check
"Troubleshooting." It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use factory specified replacement parts. Factory specified
replacement parts will fit right and work right because they are
made with the same precision used to build every new Jenn-Air
appliance.
To locate factory specified parts in your area, call us or your
nearest designated service center.
Call the Jenn-Air Customer eXperience Center
toll free: 1-800-688-1100.
Our consultants provide assistance with:
• Features and specifications on our full line of appliances.
• Installation information.
• Use and maintenance procedures.
• Accessory and repair parts sales.
• Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
• Referrals to local dealers, repair parts distributors, and
service companies. Jenn-Air designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
To locate the Jenn-Air designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
For further assistance
If you need further assistance, you can write to Jenn-Air with any
questions or concerns at:
Jenn-Air Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Call the Jenn-Air Canada Customer Interaction Centre toll free:
1-800-807-6777.
Our consultants provide assistance with:
• Features and specifications on our full line of appliances.
• Use and maintenance procedures.
• Accessory and repair parts sales.
• Referrals to local dealers, repair parts distributors, and
services companies. Jenn-Air Canada designated service
technicians are trained to fulfill the product warranty and
provide after-warranty service, anywhere in Canada.
For further assistance
If you need further assistance, you can write to Jenn-Air Canada
with any questions or concerns at:
Jenn-Air Brand Home Appliances
Customer eXperience Centre
1901 Minnesota Court
Mississauga, Ontario L5N 3A7
Please include a daytime phone number in your correspondence.
16
Loading...