Jenn-Air JUBFL242HX, JUBFR242HX User Manual
UNDER COUNTER BEVERAGE CENTER
For questions about features, operation/performance, parts, accessories, or service, call:
1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.
W11325206B
TABLE OF CONTENTS
INTRODUCTION
Safety ....................................................................................................................3
Proper Disposal of Your Old Beverage center ..........................4
Features ..............................................................................................................4
INSTALLATION REQUIREMENTS
Tools and Parts ...............................................................................................5
Location Requirements ...........................................................................5
Product Dimensions ..................................................................................6
Custom Overlay Panel ..............................................................................6
Handle (Optional).........................................................................................7
Electrical Requirements ..........................................................................8
INSTALLATION INSTRUCTIONS
Unpack the Beverage center ...............................................................8
Custom Overlay Panel Installation ...................................................9
Installation and Door Closing ..............................................................10
USING BEVERAGE CENTER
Controls ...............................................................................................................11
Normal Sounds ..............................................................................................12
Stocking the Beverage center ............................................................13
Wine Racks .......................................................................................................13
Beverage Center Shelves ........................................................................13
CARE AND CLEANING
Cleaning .............................................................................................................14
Removing Base Grille ................................................................................14
Vacation Care ..................................................................................................14
Moving Care .....................................................................................................14
TROUBLESHOOTING
Operation ...........................................................................................................15
Temperature and Moisture ...................................................................15
Door .......................................................................................................................15
ASSISTANCE
IN the U.S.A. .....................................................................................................16
IN Canada ..........................................................................................................16
Warranty .............................................................................................................17
2
INTRODUCTION
SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Plug into a grounded 3 prong outlet.
■
Do not remove ground prong.
■
Do not use an adapter.
■
■ Do not use an extension cord.
■ Disconnect power before servicing.
■ Replace all parts and panels before operating.
■ Remove doors from your old beverage center.
■ Use non flammable cleaner.
■ Do not store or use petrol, flammable liquids or gas in the
vicinity of this or other electrical appliances. The fumes can
cause fires or explosions.
■ Do not store explosive substances such as aerosol cans with
a flammable propellant in this beverage center.
■ Do not use or place electrical devices inside the beverage
center compartments if they are not of the type expressly
authorized by the manufacture.
■ Use two or more people to move and install beverage center.
To reduce the risk of fire, electric shock, or injury when using your beverage center, follow these basic
precautions:
■ This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
■
play with the appliance.
■ To avoid the risk of children becoming trapped and
suffocating, do not allow them to play or hide inside the
beverage center.
■ If the power supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly qualified
person.
■ Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
■ Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by
the manufacturer.
■ Do not damage the refrigerant circuit.
SAVE THESE INSTRUCTIONS
3
PROPER DISPOSAL OF YOUR
OLD BEVERAGE CENTER
WARNING
Suffocation Hazard
Remove doors from your old beverage center.
Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not
problems of the past. Junked or abandoned beverage
centers are still dangerous – even if they will sit for “just
a few days.” If you are getting rid of your old beverage
center, please follow these instructions to help prevent
accidents.
Before You Throw Away Your Old Beverage center:
Take off the door.
Leave the racks in place so that children may not
easily climb inside.
1. Stealth Flush Design with
Smooth Close Door
Create an unbroken silhouette. Discreet 1/8" reveals
envelop every side, without exposed hinges or trim
pieces. Quiet, soft, secure. An articulating hinge
discreetly ushers the door open and gently pulls it
closed.
2. Daring Obsidian Interior
Inspired by volcanic glass, this dark finish erupts
with reflective, high-contrast style. Let the object of
your desire emerge like vibrant art, begging to be
consumed.
3. Glass Shelves
Gaze through platforms of glass wrapped in
unyielding shelf frames.
4. UV-Resistant Thermal Glass
Let your tongue meet tannins. Double-paned
glass helps filter out ultraviolet light and rejects
temperature swings to sustain the body and finish
you covet.
5. LED Lighting
LED lights instinctively come alive, chasing away
shadows to reveal vivid details.
Important information to know about disposal of
refrigerants:
Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.
FEATURES
14.
13.
12.
9,10,11.
2.
3.
4.
5.
6.
7.
8.
6. Independent Temperature Zones
Compose ideal climates for choice beverages and
tempting bites. Two temperature zones and six
curated presets await your command.
7. Smooth Close Racks
Smooth moves. Each beechwood rack opens and
closes fluidly and quietly, even when fully loaded.
8. 13 Bottle Capacity
Take your fill. Relish the spine-tingling flavors of wines
at your leisure.
9. NOIR™ Design Expression
Lose yourself in a world that’s yours alone. Crisp
1.
silhouettes crackle with mystique; beguiling
reflections flow in and out of sight. Taut with
ceaseless allure and minimalist appeal, the NOIR™
design expression rejects dated ideals of beauty.
10. RISE™ Design Expression
Embrace an era of striking proportions. A stainless
steel suit of armor gleams with spectacular light. This
is strength—inextricable from beauty. Forged in the
fires of progress, the RISE™ design expression towers
over stagnant, uninspired designs that have inherited
undeserved standing.
11. Custom Overlay Design
Break free with custom panels that allow
unapologetic expression. Custom panels and handles
must be purchased separately.
12. Auto Light Option
Features a proximity sensor in the base grille that
automatically ramps on the LED interior display
lighting when motion is detected.
4
13. Hushed Acoustics
Our internal compressor keeps your beverages
impeccably chilled, while running unobtrusively in
the background. Brilliance doesn’t have to announce
itself; it just is.
INSTALLATION REQUIREMENTS
14. Emotive Controls
Hold sway over every zone. Let your light-guided
touch coax out the flavors of beverages, spirits and
beyond.
TOOLS AND PARTS
Gather the required tools and parts before starting
installation
TOOLS AND PARTS NEEDED:
Phillips screwdriver
Custom Overlay Door Panel — Refer “Custom Overlay
Panel Preparation.”
Custom handle and mounting hardware (optional)
PARTS SUPPLIED:
M4 x 30 flathead screws (8)
LOCATION REQUIREMENTS
WARNING
Explosion Hazard
Keep flammable materials and vapors,
such as gasoline, away from beverage center.
Failure to do so can result in death, explosion, or fire.
OPENING DIMENSIONS
Height dimensions are shown with the leveling legs
extended to the minimum height.
NOTE: When leveling legs are fully extended, add
5/8" (15 mm) to the height dimensions. See “Product
Dimensions.”
If the floor of the opening is not level with the kitchen
floor, shim the opening to make it level with the
kitchen floor.
G
I
C
E
H
B
F
G
F
D
Recessed
receptacle
locations
Utility
opening
IMPORTANT: This appliance is intended to be used in
household and similar applications such as:
Staff kitchen areas in shops, office and other working
environments;
Farm houses and by clients in hotels, motels and
other residential type environments;
Bed and breakfast type environments;
Catering and similar non-retail applications.
NOTES:
For the beverage center to be flush with the front
of the base cabinets, remove any baseboards or
moldings from the rear of the opening. See “Product
Dimensions” and later in this section, “Opening
Dimensions.”
It is recommended that you do not install the
beverage center near an oven, radiator, or other heat
source.
Do not install in a location where the temperature will
fall below 55°F (13°C). For best performance, do not
install the beverage center behind a cabinet door or
block the base grille.
A
Opening and utility location dimensions
Opening width - A 24" (60.96 cm) min.
Opening depth - B 24" (60.96 cm) min.
Opening height - C 34⁄" (87.6 cm) min.
35" (88.9 cm) max.
Dimension - D 12⁄" (30.64 cm)
Dimension - E 21⁄" (55.16 cm)
Dimension - F 1⁄" (4.44 cm)
Dimension - G 3" (7.55 cm)
Dimension - H 4⁄" (11.37 cm)
Dimension - I 9⁄" (23.47 cm)
For flush installation, the power outlet can be installed in
adjacent cabinetry with a cutout on the power cord side
for routing of the power cord.
The power outlet can also be recessed on the back
wall behind the unit as per recommended receptacle
locations in the above illustration.
5
PRODUCT DIMENSIONS
OVERALL PRODUCT
Width (up to hinge cover) 23⁄" (60.72 cm)
Height (up to hinge cover) 34⁄" (87.32 cm)
Glass door model (NOIR™) depth
(no handle)
Glass door model (RISE™) depth
(no handle)
Solid door models
(NOIR™/ RISE™)
Panel ready models depth
(with 3/4" panel and no handle)
Raw Door Height 30⁄" (77.75 cm)
NOTE: The power cord is 60" (152.4 cm) long.
23⁄" (60.36 cm)
23⁄" (60 cm)
23⁄" (60 cm)
23⁄" (60.5 cm)
SOLID DOOR OVERLAY PANEL PREPARATION
Create the custom overlay panel using the dimensions
shown in the illustration “Solid door overlay panel and
hinge routing dimensions”. Route shaded areas to a 1/2"
(12 mm) depth as shown.
IMPORTANT: The following graphic shows a custom
panel for a door with the hinges installed on the righthand side. If your beverage center has the hinges
installed on the left-hand side, rotate the custom frame
180° so the hinge markings will be on the left.
1/4"
(7 mm)
2"
1/8"
(3 mm)
4⁄"
(125 mm)
(53 mm)
23⁄"
(60.72 cm)
34⁄"
(87.32 cm)
Depth
(no handle)
30⁄"
(77.5 cm)
CUSTOM OVERLAY PANEL
NOTE: For standard stainless steel or glass door
models, skip these instructions and go to "Electrical
Requirements" section.
If you plan to install a custom overlay panel, you will
need to create the panel yourself or consult a qualified
cabinetmaker or carpenter. Refer dimension drawings for
panel specifications.
IMPORTANT:
The thickness of the overlay panel must be 3/4"
(19 mm).
Custom solid door overlay panel must not weigh
more than 20 lbs (9.07 kg).
Custom glass door overlay panel must not weigh
more than 10 lbs (4.54 kg).
Overlay panels weighing more than recommended
may cause damage to your appliance.
1/2"
(12 mm)
30⁄"
(77.75 cm)
Solid door overlay panel and hinge routing dimensions
23⁄"
(60.3 cm)
6
GLASS DOOR OVERLAY PANEL PREPARATION
Create the custom overlay panel using the dimensions
shown in the illustration “Glass door overlay panel and
hinge routing dimensions”. Route shaded areas to a 1/2"
(12 mm) depth as shown.
IMPORTANT: The following graphic shows a custom
panel for a door with the hinges installed on the righthand side. If your beverage center has the hinges
installed on the left-hand side, rotate the custom frame
180° so the hinge markings will be on the left.
1/4"
(7 mm)
2"
1/8"
(3 mm)
1/2"
(12 mm)
4⁄"
(125 mm)
(53 mm)
30⁄"
(77.75 cm)
HANDLE OPTIONAL
Custom handles are typically attached to the custom
overlay door panel only.
Refer instructions received with JennAir® RISETM and
NOIRTM handle kits to install these handles on custom
wood panels.
Custom handle needs to be installed on the door panel
with countersunk holes and installed before the custom
overlay door panel has been installed on the beverage
center door.
17⁄"
(43.3 cm)
21⁄"
(55.4 cm)
Glass door overlay panel and hinge routing dimensions
23⁄"
(60.3 cm)
7
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
INSTALLATION INSTRUCTIONS
Before you move your beverage center into its final
location, it is important to make sure you have the proper
electrical connection.
RECOMMENDED GROUNDING METHOD
A 115 V, 60 Hz, AC only, 15 or 20 A fused, grounded
electrical supply is required. It is recommended that a
separate circuit serving only your beverage center be
provided. Use an outlet that cannot be turned off by a
switch. Do not use an extension cord.
NOTE: Before performing any type of installation,
cleaning, or removing a light bulb, unplug beverage
center or disconnect power.
UNPACK THE BEVERAGE CENTER
WARNING
Excessive Weight Hazard
Use two or more people to move and install beverage
center.
Failure to do so can result in back or other injury.
Before using your beverage center, all packaging
materials should be removed and the interior should be
cleaned.
Remove tape and glue residue from surfaces before
turning on the beverage center. With your fingers,
rub a small amount of liquid dish soap over any
adhesive and wipe with warm water to remove.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These can damage the surfaces of
your beverage center. For more information, refer
“Beverage center Safety” section.
Dispose of and/or recycle all packaging materials.
After all packaging materials have been removed,
clean the inside of your beverage center. Refer the
cleaning instructions in “Cleaning” section.
NOTE: For standard stainless steel or glass door models,
skip to “Door Closing” section.
8
CUSTOM OVERLAY PANEL INSTALLATION
A
B
A
IMPORTANT:
Create custom overlay panel according to the
specifications in the “Custom Overlay Panel” section.
JennAir is not responsible for the removal or addition
of molding or decorative panels that would not allow
access to the beverage center for service.
1. Open the door completely to 90°.
90°
2. Remove the gasket from the corners of the door,
pulling gently until the two screw holes in each
corner of the door can be seen.
NOTE: The gasket does not have to be removed from
the door, only the corners.
3. Using two people, hold the custom overlay panel
against the door. Be sure that the top and bottom
hinges fit accurately into the routing on back of the
custom wood panel.
NOTE: Handle needs to be installed before the custom
overlay door panel has been installed on the beverage
center door.
4. Fasten the custom panel to the door using two wood
screws (provided in installation kit) at each corner.
A
A. M4 x 30 flathead screws (provided in installation kit)
A
A. Screw holes
B. Gasket
5. Press the gasket firmly back into it’s original position.
9
INSTALLATION AND DOOR CLOSING
Your beverage center has four leveling legs. If your
beverage center seems unsteady or you want the door to
close more easily, adjust the beverage center’s tilt using
the instructions below.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
2. Move the beverage center into its final location.
3. Turn the leveling legs to the right to lower the
beverage center, or turn the leveling legs to the left to
raise it. It may take several turns of the leveling legs to
adjust the tilt of the beverage center.
NOTE: Having someone push against the top of the
beverage center takes some weight off the leveling
legs. This makes it easier to adjust the leveling legs.
4. Open the door and check that it closes as easily as
you like. If not, tilt the beverage center slightly more
to the rear by turning both front leveling screws to
the right. It may take several more turns, and you
should turn both leveling legs the same amount.
WARNING
Excessive Weight Hazard
Use two or more people to move and install beverage
center.
Failure to do so can result in back or other injury.
When Moving Your Beverage Center:
Your beverage center is heavy. When moving the beverage
center for cleaning or service, be sure to cover the oor with
cardboard or hardboard to avoid oor damage. Always pull
the beverage center straight out when moving it. Do not
wiggle or “walk” the beverage center when trying to move it,
as oor damage could occur.
10
CONTROLS
12 34 456 78 95
USING BEVERAGE CENTER
NOTE:
When the beverage center is turned On for the first
time, the temperature defaults to the recommended
setting.
There are two adjustable temperature controls, one
for each compartment.
The left temperature and preset touch pads control
the temperature of the upper compartment.
The right temperature and preset touch pads control
the temperature of the lower compartment.
1. Turning Control On/Off
The first time that the beverage center is plugged in,
the control will be in Cool Off mode. Cool On and Cool
Off will be the only options that display.
Press COOL ON for 3 seconds to turn on the beverage
center. All menus and recommended temperature
settings will be displayed.
2. Auto Light Option
Features a proximity sensor in the base grille that
automatically ramps on the LED interior display
lighting when motion is detected. When motion is no
longer detected, the interior display light will turn off
after 2 minutes.
Press the AUTO LIGHT option to activate this
feature.
When the Auto Light is not activated, the interior
display light will only turn on when the door is
opened.
NOTE:
Leaving the light on for an extended period of
time will slightly increase the temperature of the
beverage center.
3. Control Lock
A selectable feature that locks all controls except for
Cool On and Cool Off.
To activate Lock Mode, press and hold LOCK for
3 seconds. After the countdown, all other displays
will turn off and become unavailable except Cool
On, Cool Off and Lock.
4. Using Presets
For your convenience, your beverage center also
has controls that are preset to recommended
storage temperature for specific beverages. Pressing
any preset option will set the temperature to the
recommended temperature for the specified
beverage:
Beverage: 34°F (1°C)
Party: 37°F (3°C)
Red Wine: 64°F (17°C)
White Wine: 50°F (10°C)
Champagne: 46°F (7°C)
Sweet Wine: 42°F (5°C)
5. Adjusting the Temperatures
To adjust set point temperatures, press “+” (plus) or
“-” (minus) until the desired temperature setting
is reached. The control is set correctly when the
beverages are as cold as you like it.
NOTE:
The set point for the beverage center is 37°F (3°C)
for the upper compartment and 50°F (10°C) for
the lower compartment. The set point range for
the upper compartment is 33°F to 40°F
(0°C to 4°C) and 42°F to 64°F (5°C to 17°C) for the
lower compartment.
Wait at least 24 hours between adjustments
for the product to acclimate. Recheck
the temperatures before making further
adjustments.
6. Viewing Celsius/Fahrenheit
Temperatures
Press the F/C touch pad to toggle between displaying
the temperature in degrees Fahrenheit and degrees
Celsius. The corresponding indicator will illuminate.
7. Sabbath Mode
Allows the door of the beverage center to be opened
or closed during the Sabbath or other religious
holidays without directly turning on or off any lights,
digital readouts, solenoids, fans, valves, icons, tones,
alarms or the compressor. By selecting this feature,
the temperature set points remain unchanged, but
the control panel lights, interior lights, and control
audio turn off. For most efficient beverage center
operation, it is recommended to exit the Sabbath
Mode when it is no longer required.
Press and hold SABBATH for 3 seconds to turn on
the feature. After the 3 second countdown, the
feature will activate and all other displays will turn
Off.
Press and hold SABBATH for 3 seconds to turn off
the feature and turn on the display.
11
8. Over Temp Alarm
Helps avoid food and beverage spoilage by chiming if
the temperature in either zone rises above the preset
range for 10 minutes.
The audio alarm will shut off automatically when the
temperature returns to normal. To let you know an
Over Temperature condition occurred, the indicator
light will continue to flash until the Reset Alarm touch
pad is pressed. If the over temperature condition is
still present when an Over Temp reset is performed,
the indicator light will continue to reactivate every
4 hours until the beverage center temperature is
below preset range.
NOTE: These features will not appear on your control
unless your beverage center is above preset range
and the alarm requires a reset.
9. Max Cool
Plummets internal temperatures to their lowest point
for 24 hours.
Press MAX COOL to turn on the feature. The
feature will activate.
Press MAX COOL to turn off the feature and
return to the previous settings.
10. Door Open Alarm
Helps avoid food and beverage spoilage by giving
an audio and visual alert if the door is left open for 10
minutes.
If the door is open longer than 10 minutes, an alarm
will sound every 2 minutes until the door is closed or
any control is pressed.
NORMAL SOUNDS
Your new beverage center may make sounds that your
old one didn’t make. Because the sounds are new to you,
you might be concerned about them. Most of the new
sounds are normal. Hard surfaces, such as the flooring
and surrounding structures, can make the sounds seem
louder. The following describes the kinds of sounds and
what may be making them.
Your beverage center is designed to run more
efficiently to keep your beverages at the desired
temperatures and to minimize energy usage. The
high efficiency compressor and fans may cause your
beverage center to run longer than your old one.
You may also hear a pulsating or high-pitched sound
from the compressor or fans adjusting to optimize
performance.
Rattling noises may come from the flow of refrigerant
or items stored inside the beverage center.
As each cycle ends, you may hear a gurgling sound
due to the refrigerant flowing in your beverage
center.
You may hear water running into the drain pan when
the beverage center is defrosting.
You may hear clicking sounds when the beverage
center starts or stops running.
11. Showroom Mode
This mode is used only when the beverage center
is on display in a retail store. If you unintentionally
turn on Showroom Mode, Cool Off will light up on
the display, and the controls will appear to work. Exit
Showroom Mode by pressing and holding COOL ON
and SABBATH at the same time for 3 seconds.
12
Loading...