Jenn-Air JS42NXFXDW, JS48NXFXDW Dimension Guide
Side by Side Built-In Refrigerator
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
Electrical: A 115 Volt, 60 Hz., AC only 15- or 20-amp fused,
grounded electrical supply is required. It is recommended that a
separate circuit serving only your refrigerator be provided. Use
an outlet that cannot be turned off by a switch. Do not use an
extension cord.
Water Supply: A cold water supply with water pressure of
between 30 and 120 psi (207 - 827 kPa) is required to operate
the water dispenser and ice maker. If you have questions about
your water pressure, call a licensed, qualified plumber.
If a reverse osmosis water filtration system is connected to
your cold water supply, the water pressure to the reverse
osmosis system needs to be a minimum of 40 to 60 psi (276 414 kPa).
The water shutoff should be located in the base cabinet on
either side of the refrigerator or some other easily accessible
area. If the water shutoff valve is not in the cabinets, the
plumbing for the water line can come through the floor.
Location: It is recommended that you do not install the
refrigerator near an oven, radiator, or other heat source.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
W10231368-D-JA
5/09
JS42NXFXDW
JS48NXFXDW
■ The power cord is 84" (213 cm) long.
■ The water supply line is located at the front of the refrigerator.
■ Width dimensions were measured from hinge to hinge.
■ The depth from the front face of the doors to the back of the refrigerator cabinet is 24" (60.96 cm) without
panels.
■ The required thickness for all custom overlay panels is
3
⁄4" (1.91 cm).
DOOR SWING DIMENSIONS
TOP VIEW
FRONT VIEW
IMPORTANT:
■ Flooring under refrigerator must be at same level as the room. Face of cabinetry
must be plumb.
■ The width of the opening (Width A), must be as specified for your model, for at
least 2" (5.08 cm) back from the face of the cabinet. If your opening does not
meet this requirement, you will need to make modifications.
Model Width A (as shown above)
42 42" (106.7 cm)
48 48" (121.9 cm)
Model A
42 413⁄4" (106 cm)
48 473⁄4" (121.3 cm)
Installation Type Depth B (as shown above)
Standard Flush
(new installation)
25" (63.5 cm) minimum
Retrofit Installations 24" (60.9 cm) minimum
Model Width A
(hinge edge to hinge edge)
42 413⁄4" (106 cm)
48 473⁄4" (121.3 cm)
The location must permit both doors to open to a minimum of 90°. Allow 41⁄2" (11.4 cm) minimum space
between the side of the refrigerator and a corner wall.
NOTE: More clearance may be required if you are using overlay panels, custom handles, or extended
handles.
Model A
B C D
42 403⁄4" (103.5 cm)
393⁄4" (101.0 cm) 453⁄8" (115.3 cm) 463⁄4" (118.8 cm)
48 431⁄4" (109.9 cm)
42" (106.7 cm) 485⁄8" (123.5 cm) 501⁄4" (127.6 cm)
80" - 90"
(203-229 cm)
4"
(10.2 cm)
*84"
(213.4 cm)
24"
(61.0 cm)
A
A
(see chart following)
84" (213.4 cm)
to bottom of solid soffit
77"
(196 cm)
A
Width
(see chart following)
B
1"
6"
(15.2 cm)
(2.54 cm)
6"
(15.2 cm)
BA C D
90˚
110˚
90˚
110˚
Loading...