Jenn-Air JMDFS24JL Installation Manual

24" (61.0 CM) AND 30" (76.2 CM) MICROWAVE

DRAWER AND 27" (68.6 CM) TRIM KIT

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION DU TIROIR À

FOUR À MICRO-ONDES DE 24 PO (61,0 CM) ET 30

PO (76,2 CM) ET DE LA TROUSSE DE GARNITURE

DE 27 (68,6 CM)

Table of Contents/Table des matières

MICROWAVE DRAWER SAFETY ..................................................2

INSTALLATION REQUIREMENTS .................................................3

Tools and Parts .............................................................................3

Location Requirements ................................................................3

Minimum Dimensions...................................................................3

Electrical Requirements ...............................................................4

24" (61.0 CM) AND 30" (76.2 CM) STANDARD MOUNT .............5

Cabinet Preparation .....................................................................5

24" (61.0 CM) AND 30" (76.2 CM) FLUSH MOUNT .....................6

Cabinet Preparation .....................................................................6

27" (68.6 CM) TRIM KIT ACCESSORY STANDARD MOUNT .... 7

Cabinet Preparation .....................................................................7

27" (68.6 CM) TRIM KIT ACCESSORY FLUSH MOUNT .............8

Cabinet Preparation .....................................................................8

INSTALLATION INSTRUCTIONS ...................................................9

Install the Anti-Tip Block ..............................................................9

Install the Microwave Drawer .......................................................9

Install the Deector Vent For Flush Installation .........................10

Complete Installation .................................................................10

ASSISTANCE ................................................................................10

IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.

IMPORTANT:

Save for local electrical inspector’s use.

IMPORTANT :
Installateur : Remettre les instructions d’installation au propriétaire.
Propriétaire : Conserver les instructions d’installation pour référence

ultérieure.

IMPORTANT :

À conserver pour consultation par l’inspecteur local des installations
électriques.

W11257634B
TINSKB267MRR0

SÉCURITÉ DU TIROIR À MICRO-ONDES .................................11

EXIGENCES D’INSTALLATION ...................................................12

Outillage et pièces ......................................................................12

Exigences d’emplacement .........................................................12

Dimensions minimales ...............................................................12

Spécications électriques ..........................................................13

SUPPORT STANDARD DE

24 PO (61,0 CM) ET 30 PO (76,2 CM) .........................................14

Préparation de l’armoire .............................................................14

EN AFFLEUREMENT DE

24 PO (61,0 CM) ET 30 PO (76,2 CM) .........................................15

Préparation de l’armoire .............................................................15

SUPPORT STANDARD POUR TROUSSE

DE GARNITURE DE 27 PO (68,6 CM) .........................................16

Préparation de l’armoire .............................................................16

EN AFFLEUREMENT POUR TROUSSE DE

GARNITURE DE 27 PO (68,6 CM) ...............................................17

Préparation de l’armoire .............................................................17

INSTRUCTIONS D’INSTALLATION .............................................18

Installation de la cale de bride antibasculement .......................18

Installation du tiroir à micro-ondes ............................................18

Installer le déecteur d’évacuation pour une

installation en afeurement ........................................................19

Terminer l’installation .................................................................. 20

ASSISTANCE ................................................................................20

MICROWAVE DRAWER SAFETY

2

INSTALLATION REQUIREMENTS

A

These installation instructions cover different models. The
appearance of your particular model may differ slightly from the
illustrations in these Installation Instructions.

Tools and Parts

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.

Tools needed

■ Tape measure

■ #2 Phillips screwdriver

■ Drill

■ 1/8" (3.17 mm) drill bit

■ Marker or pencil

Minimum Dimensions

Minimum Wall Oven Combination Installation
Clearances

For proper installation, the following minimum clearances must
exist above and below the cutout opening.

NOTE: Upper oven must have heat deector kit installed to
direct exhaust away from microwave console (Refer to Wall Oven
Manual for Deector Kit Installation)

Parts supplied

The Microwave Drawer is preassembled.

■ 1" (2.5 cm) mounting screws (4)

■ 1" (2.5 cm) deector screws (2)

■ Flush mount deector (1)

Optional Parts

■ 27" (68.6 cm) Trim Kit (W11170223) for JMDFS24GS

■ 27" (68.6 cm) Trim Kit (W11264778) for JMDFS24HM

Verification needed

■ Installer must conrm presence of anti tip block. Refer to the

anti-tip block section in the manual.

■ Check local codes. Check existing electrical supply. See

“Electrical Requirements”.

■ It is required that all electrical connections be made by a

licensed, qualied electrical installer.

Location Requirements

This product is suitable for use below electric or gas built-in
ovens. This product is not suitable for use below cooktops.

The Microwave Drawer may be located in a cabinet or below
the counter, and/or below a built-in oven. Check the opening
where the Microwave Drawer will be installed. The location must
provide:

IMPORTANT: Observe all governing codes and ordinances.

■ Wood cabinetry.

■ Cutout opening that is plumb and square. See “Minimum

Cutout Dimensions” in the “Minimum Dimensions” section.

■ Cutout oor that is solid, level, and ush with bottom of

cabinet cutout.

■ Support for weight of at least 100 lbs (45.4 kg), which

includes Microwave Drawer and items placed inside.

■ Grounded electrical outlet. See the “Electrical Requirements”

section.

■ Minimum installation clearances for installation location. See

the “Minimum Dimensions” section.

■ Complete enclosure around the recessed portion of the

Microwave Drawer.

2" (5.1 cm)

B

A. Upper oven cutout
B. Microwave drawer cutout

3

Product Dimensions

(40.6 cm

)

(40.6 cm

(37.1 cm)

24" (61.0 cm) and 30" (76.2 cm)

"

4¹¹⁄₁₆

(11.9 cm)

1

³/₄

16

" (4.4 cm

"

)

4" (10.2 cm)

)

A

Dimension A:
24" (61.0 cm) Product - 237/8" (60.6 cm)
30" (76.2 cm) Product - 2915/16" (76.0 cm)
Dimension B:
JMDFS24GS Model - 15/8" (4.1 cm)
JMDFS30HL Model - 111/16" (4.3 cm)
JMDFS24HM Model - 13/4" (4.4 cm)
JMDFS30HM Model - 13/4" (4.4 cm)

Optional 27" (68.6 cm) Trim Kit:

"

4¹¹⁄₁₆

(11.9 cm)

" (4.4 cm

1

³/₄

"

16

)

)

4" (10.2 cm)

"

23

⁷/₈

(60.6 cm)

"

₄

26

³/

(68.0 cm)

21

⁵/₈ "

(54.9 cm)

21

⁵/₈ "

(54.9 cm)

22 ¹/₁₆"

(56.0 cm)

B

22 ¹/₁₆"

(56.0 cm)

1⁵/₈"

(4.1 cm)

14 ⁹⁄₁₆ "

(37.1 cm

14 ⁹⁄₁₆

Electrical Requirements

IMPORTANT: Observe all governing codes and ordinances.

Required:

■ A 120 V, 60 Hz, AC-only, 15 or 20 A electrical supply with a

fuse or circuit breaker.

Recommended:

■ A time-delay fuse or time-delay circuit breaker

■ A separate circuit serving only this Microwave Drawer

GROUNDING INSTRUCTIONS

■

For all cord connected appliances:

The microwave oven must be grounded. In the event of
an electrical short circuit, grounding reduces the risk of
electric shock by providing an escape wire for the electric
current. The microwave oven is equipped with a cord
having a grounding wire with a grounding plug. The plug
must be plugged into an outlet that is properly installed

"

and grounded.

WARNING: Improper use of the grounding plug can

result in a risk of electric shock. Consult a qualified
electrician or serviceman if the grounding instructions are
not completely understood, or if doubt exists as to whether
the microwave oven is properly grounded.

Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the microwave oven. A short power supply
cord is provided to reduce the risks resulting from becoming
entangled in or tripping over a longer cord.

The drawer opens 151/

4

4

" (38.7 cm).

SAVE THESE INSTRUCTIONS

15 ¹/₄" (38.7 cm)

24" (61.0 CM) AND 30" (76.2 CM) STANDARD MOUNT

B

C

D

E

F

G

H

I

I

J

K

N

L

M

A

Top view

Cabinet Dimensions

Cabinet Preparation

Cabinet

face

A. 6" (152.40 mm) minimum

16" (406.40 mm) maximum

B. Suggested electrical receptacle location
C. Anti-Tip block
D. 3" (76.20 mm)
E. 31/2" (88.90 mm)
F. 4.5" (114.30 mm)
G. 221/8" (561.98 mm) opening
H. 1413/16" (376.24 mm) to bottom

of Anti-Tip block

I. 24" models: Allow 7/8" (22.2 mm)

overlap

30" models: Allow 41/16" (103.19mm)

overlap

J. 24" (609.60 mm) minimum depth
K. Allow 9/16" (5.62 mm)
L. Platform must support 100 lb (45.4 kg)
M. 159/16" (395.27 mm) opening
N. Allow 3/4" (19.05 mm) overlap
O. JMDFS24GS Model - 15/8" (41.28 mm)

JMDFS30HL Model - 111/16" (42.86 mm)
JMDFS24HM Model - 13/4" (44.45 mm)
JMDFS30HM Model - 13/4" (44.45 mm)

O

Drawer

face

Anti-Tip block

G

5

24" (61.0 CM) AND 30" (76.2 CM) FLUSH MOUNT

L

I

Cabinet Dimensions

Cabinet Preparation

A

B

C

R

G

K

D

E

F

H

O

Note: The face of the shelf must

sit 1⁷/₈" (47.6 mm) back from

the face of the cabinet.

M

J

Shelf face

L

N

Cabinet face

Flush mount deector vent

³/₄" (19.05 mm)

A. 6" (152.40 mm) minimum

16" (406.40 mm) maximum
B. Suggested electrical receptacle location
C. Anti-Tip block
D. 3" (76.20 mm)

Anti-Tip block

K

K

Top view

6

Drawer

face

Mounting

cleat

P

Cabinet

Q

face

E. 31/2" (88.90 mm)
F. 4.5" (114.30 mm)
G. 24" models: 243/16" (614.4 mm) minimum

30" models: 301/4" (768.4 mm) minimum
H. 1413/16" (376.24 mm) to bottom

of Anti-Tip block
I. 1" (25.40 mm) minimum
J. 24" (609.60 mm) minimum depth
K. 221/8" (561.98 mm) “mounting cleat to

mounting cleat”
L. 17/8" (47.62 mm)
M. 167/8"(428.62 mm) opening
N. Platform must support 100 lb (45.4 kg)
O. 161/8" (409.56 mm)
P. 0" (0 mm) = ush
Q. JMDFS24GS Model - 15/8" (41.28 mm)

JMDFS30HL Model - 111/16" (42.86 mm)

JMDFS24HM Model - 13/4" (44.45 mm)

JMDFS30HM Model - 13/4" (44.45 mm)
R. 159/16" (395.3 mm)