Jenn-Air JMC8130DDS Installation Instruction

INSTALLATION

INSTRUCTIONS

Built-In 27²²²² &30²²²²

Microwave Ovens

Improper installation of the grounding circuit can result in a risk of electric shock.

27² &30² MICROWAVE OVEN DESCRIPTION

1 Properly Polarized and Grounding Outlet. 25/8² Plywood Floor (Must Support 100 lbs.) 3 About 15-7/8 Inches 4 About 1-3/8 Inches

27² MICROWAVE OVEN DIMENSIONS

inches Centimeters

A 27 MIN 68.58 MIN B 24 MIN 60.96 MIN C22-5/8+ D 24 MIN 60.96MIN E25-1/2+ F 23-7/16 59.69 G 26-3/4 67.95 H 20-3/16 51.27

1/16 57.47 + 0.16

1/16 64.77 + 0.16

403 WEST FOURTH STREET, NORTH

NEWTON, IA 50208

MICROWAVE OVEN CUTOUT

Bottom Grill

30² MICROWAVE OVEN DIMENSIONS

inches Centimeters

A 30MIN 76.2MIN B 24 MIN 60.96 MIN C22-5/8+ D 24 MIN 60.96MIN E28-1/2+ F 23-7/16 59.69 G 29-3/4 75.56 H 20-3/16 51.27

Z Do not block airintake slots alongtop ofoven.

1/16 57.47 + 0.16

1/16 72.39 + 0.16

NOTES

CAUTION

For European stylecabinets (flush front) the required clearance for operation of the oven door is minimum spacing of 7/8² between the cutout and the door, hinge or drawer of the cabinet. Some built-in cabinets may not be wide enough, due to their construction, to allow this installation.

3828W5U0230

8101P504-60

(05-03-02)

INSTALLATION

1. Cut hole in cabinet to mount Microwave oven. Cutout in cabinet should be level and straight.

NOTE: There are no provisions to level the unit after it is installed. An oven that is not level could cause poor cooking results.

2. Install plywood floor as shown above.

3. Attach unit to the cabinet with 4 long oval head screws supplied inside of envelope containing these instructions. Pre-drill 4 holes in cabinet for attachment screws using 1/16² drill. Oven mounting holes are provided in side trim.

4. Attach the bottom grill, found in the upper packing materials, to the front plate with the 2 short truss head screws supplied in the envelope packaged with the bottom grill.

5. See Owner’s Manual for operating instructions.

NOTES

S Do not build in above gas wall ovens due to placement

of gas wall oven vent.

Electrical rating of this oven:

S 120 VAC @ 60 Hz. S 13 A / 1000 W S You need a DEDICATED 120 VAC, 60 Hz, 15 A or 20

A, fused electrical supply (located in the cabinet with

the microwave as close as possible to the microwave) serving only the microwave.

S Check with a qualified electrician if you are not sure

whether the oven is properly grounded or if you do not completely understand the grounding instructions.

S Do not use a fuse in the neutral or grounding circuit. S Save these instructions for the local electrical

inspector’s use.

S If there is an electrical short circuit, grounding reduces

the risk of electrical shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.

S Place the plug into a properly installed and grounded

outlet.

S Maytag does not recommend use of an extension

cord.

S Keep the power cord dry and do not pinch or crush it. S Do not, under any circumstances, remove the power

supply cord grounding prong!

S This appliance MUST

be grounded!

SERVICE

Interrupt the sourceof electricitytotheunitwhenattempting to repair or service the oven. Failure to do this could result in a dangerous or even fatal shock.

Dim “A” = With Warming Drawer = 69² Dim “A” = Without Warming Drawer = 59¼²

Unit approved for use over the following wall ovens:

Dim “A” = With Warming Drawer = 62½² Dim “A” = Without Warming Drawer = 59¼²

JJW9530D JJW9527D JJW7530DD JJW8530D JJW8527D JWD7030CDX

SAME FOR BOTH WITH OR WITHOUT

WARMING DRAWER