JennAir JKCPL301GL, JKCPR361GM Use & Care Guide



COLUMN REFRIGERATION



RÉFRIGÉRATION COLONNE

W10918236B

INTRODUCTION

SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately follow instructions.

DANGER

You can be killed or seriously injured if you don't follow instructions.

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

INTRODUCTION

WARNING:

■ To avoid a hazard due to instability of the

To reduce the risk of shock, or injury when using your refrigerator, follow these basic precautions:

with the instructions.

■ Installation shall be performed only by

manufacturer, or an authorized agent.

■ Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Disconnect power to all units before servicing.

■ If the SUPPLY CORD is damaged, it must be

replaced by the manufacturer, its service agent

a hazard.

■ Replace all parts and panels before operating.

IMPORTANT SAFETY INSTRUCTIONS

■ Remove doors from your old refrigerator.

■ Connect to a potable water supply only.

■ Use

■ Ke mmable materials and vapors, such

as gasoline, away from refrigerator.

■ Do not store explosive substances such as

this refrigerator.

■ Use two or more people to move and install

refrigerator.

■ Disconnect power before installing ice maker

(on ice maker kit ready models only).

■ Use a sturdy glass when dispensing ice

(on some models).

■ Do not hit the refrigerator glass doors

(on some models).

SAVE THESE INSTRUCTIONS

■ This appliance is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

■ Children should be supervised to ensure that they do

not play with the appliance.

■ This refrigerator is intended to be used in household

and similar applications such as:

working environments

–farm houses and by clients in hotels, motels,

and other residential type environments

–bed and breakfast type environments

–catering and similar non-retail applications

INTRODUCTION | 3

INTRODUCTION

PROPER DISPOSAL OF YOUR OLD REFRIGERATOR

WARNING

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER:

 Take off the doors.

 Leave the shelves in place so children may

not easily climb inside.

Important information to know about disposal of refrigerants:

Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certied refrigerant technician in accordance with established procedures.

IMPORTANT: Do your part to prevent accidental child entrapment and suffocation by properly disposing of your old refrigerator or freezer.

4 | INTRODUCTION

INTRODUCTION

REGISTERING YOUR APPLIANCE

Gain access to our concierge-level Customer Support by registering your appliance. We make product registration simple and straightforward so you can start using your exclusive JennAir beneﬁts today.

Registering your appliance allows you to:

■ Streamline your warranty service

If we have your appliance information, we can help you faster.

■ Protect your purchase

In case of an insurance loss—such as ﬁre, ﬂood, or theft—your product registration could serve as a proof of purchase.

■ Keep your family safe

We’ll notify you in the rare case of a safety notiﬁcation.

Start taking advantage of these beneﬁts today by going online to register your appliance at

https://register.jennair.com.

PRODUCT IDENTIFICATION

Your product identiﬁcation, which includes the model and serial numbers, is listed on the

product rating plate. Recording this information below allows us to

assist you more easily if your appliance should ever require service from one of our JennAir® Authorized Service Providers.

Model Number: ______________________________

Serial Number: _______________________________

Date of Installation: _________________________

Authorized Dealer: __________________________

Authorized Dealer Phone #: _________________

TABLE OF CONTENTS

INTRODUCTION

Safety ............................................................................. 3

Proper Disposal of

Your Old Refrigerator ......................................... 4

Registering Your Appliance ............................ 5

Product Identiﬁcation ........................................ 5

Product Features .................................................... 6

Refrigerator Controls ........................................... 8

Freezer Controls ...................................................... 10

GETTING STARTED

Before Use ................................................................... 12

Smart Features ........................................................ 12

Smart Grid ................................................................... 13

Automatic Setup (WPS) ..................................... 14

Manual Setup (First-Time Use) ..................... 16

Shelves ........................................................................... 17

Deli/Crisper Drawers ............................................ 17

CARE AND CLEANING

Cleaning ....................................................................... 18

Leather Panel Care ................................................18

Vacation Care ............................................................ 19

Power Interruptions ............................................. 19

Replacing The Water Filter...............................20

TROUBLESHOOTING

Operation ..................................................................... 22

Temperature And Moisture ............................. 23

Ice And Water ........................................................... 23

Lights...............................................................................24

ASSISTANCE

Contact .......................................................................... 25

In The U.S.A. ............................................................... 25

In Canada ..................................................................... 25

Accessories ................................................................. 25

Connected Appliance

Regulatory Notices................................................26

Performance Data Sheet..................................28

Warranty.......................................................................30

TABLE DES MATIÈRES.................35

INTRODUCTION | 5

14.

13.

12.

11.

10.

INTRODUCTION

PRODUCT FEATURES

1. Fully Integrated and Flush

Design with Articulating Hinge

Creates an integrated appearance with custom cabinets without exposed hinges or trim pieces.

2. Adjustable Aluminum and

Glass Door Bins

Make it easy to customize storage according to your preferences, providing quick access to frequently used items. Refrigerator and freezer door bins can be positioned to accommodate a variety of container sizes.

3. Custom Overlay Design

Ships with factory-installed doors. To create a ﬁnished refrigerator, customers must purchase either custom overlay panels and handles from a cabinet manufacturer, or a JennAir® suite-coordinating panel kit.

4. Obsidian Interior

Showcases food items throughout the refrigerator or freezer, and provides a sharper contrast than white interiors.

6 | INTRODUCTION

5. 90°/115° Door Stop Position

Provides options to ensure ample clearance between the open door and adjacent cabinetry.

6. Wi-Fi Connectivity

This refrigerator can connect with in-home Wi-Fi to provide remote control through the JennAir® App, available to download for use with either iOS or Android devices.

INTRODUCTION

7. Soft, Auto-Close Crisper Drawers

Provide smooth operation by rolling open even when fully loaded, and feature an innovative auto-close design that pulls the drawer closed.

8. Electronic Temperature-

Controlled Crisper Drawer (Refrigerator)

Drawer slides open effortlessly, even when fully loaded, with soft, self-close glides.

Two temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

 Produce: 39°F (3.9°C)

 Assorted: 37°F (2.8°C)

9. Capacitive Touch Controls with

LED Display

The touch panel houses the control menu and function controls. The touch keypads are very sensitive and only require a light touch. The controls are located in the midsection of each column for easy access.

10. Electronic Temperature-

Controlled Deli Drawer (Refrigerator)

Deli slides open effortlessly, even when fully loaded, with soft, self-close glides.

Five temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

 Produce: 39°F (3.9°C)

 Assorted: 37°F (2.8°C)

 Beverage: 34°F (1°C)

 Deli: 33°F (0.6°C)

 Meat: 32°F (0°C)

Electronic Temperature-

Controlled Deli Drawer (Freezer)

Three temperature presets are available on the interior control to keep items at the optimal temperature. You can choose from following:

 Assorted: 0°F (-17.8°C)

 Spirits: -2°F (-18.9°C)

 DeepFreeze: -8°F (-22.2°C)

11. Water Dispenser (Refrigerator)

Allows you to dispense ﬁltered water.

12. Interior Perimeter LED Theater

Lighting

Perimeter LED lighting elegantly ramps up to full brightness when the door or interior drawers are opened, increasing visibility by minimizing shadows caused by top lighting. Selecting a cooling zone on the control panel causes the lighting in the same zone to pulse.

13. Adjustable Clear Glass Shelves

Tint-free, clear glass shelves that offer an open, reﬁned look that makes food and beverages easy to see and locate. Glass shelves complement the LED lighting for exceptional clarity that allows more light to ﬁll the interior.

14. EveryDrop® Filter

EveryDrop® water ﬁlters are NSF®† certiﬁed to reduce most contaminants, including chlorine taste and odor, lead, pesticides, and trace amounts of pharmaceuticals. EveryDrop® brand ﬁlters are the only ﬁlters tested and certiﬁed for your refrigerator system. Replace your EveryDrop® ﬁlter every 6 months for maximum contaminant reduction.

15. Automatic Ice Maker (Freezer)

Ensures a continuous supply of fresh ice cubes made from ﬁltered water.

†®

NSF is a registered trademark of NSF International.

INTRODUCTION | 7

INTRODUCTION

7. 8.

1. 2. 3.

6.5.

REFRIGERATOR CONTROLS

1. Viewing and Adjusting

Temperature

When you ﬁrst install your refrigerator, make sure that the control is still set to the recommended setting. The factory-recommended temperature is 37°F (3°C).

Touch - or + to select a

temperature seting. Press and hold - and

+ to change display from Fahrenheit to

Celsius.

2. Activate Temperature Mode for

Refrigerator Deli Drawer

Touch Assorted, Beverage, Deli, Meat, or Produce to

select a zone temperature setting.

8 | INTRODUCTION

3. Cooling Zones

Select features of your refrigerator are tied to the perimeter lighting.

Press a zone key to light the corresponding zone in your refrigerator.

INTRODUCTION

4. Max Cool

The Max Cool feature assists with periods of high refrigerator use, full grocery

loads, or temporarily warm room temperatures. Press MAX COOL to activate Max Cool. After the Max Cool cycle completes, the refrigerator will return to its previous setting.

5. Connect

Wi-Fi connectivity allows your Smart Refrigerator to connect

to the Internet and interact

with the JennAir® App from

your smartphone or mobile device. See the

“Automatic Setup—Wi-Fi Protected Setup

(WPS)” section for more information.

Sabbath

Allows the door of the refrigerator to be opened or closed during the Sabbath

or other religious holidays without activating the interior lights or controls. Press and hold Sabbath for 3 seconds to activate Sabbath mode.

Lock

The control panel can be

locked for easy cleaning or to avoid unintentional mode

changes.

6. Power Outage

The Power Outage indicator

lets you know if the power supply to the refrigerator has

been off and the temperature has risen.

Over temp Alarm

Helps avoid food spoilage and high energy costs by

sounding an alert when refrigerator temperatures remain at unusually high levels.

Door Open

The Door Open alarm feature

sounds an alarm when the

refrigerator door(s) or freezer

door is open for 5 minutes and cooling is turned on. The alarm will repeat every 2 minutes. Close the door to turn the alarm and “Door Open” alert off. To stop the alarm noise with the door open, press any key.

7. Showroom

This mode is used when the

refrigerator is on display in a

retail store or if you want to

turn the cooling off and

deactivate all other functions except interior

lighting.

To activate showroom mode, press and hold top and bottom zone

icons simultaneously for 3 seconds.

To deactivate the showroom mode, press and hold top and bottom zone icons simultaneously for 3 seconds.

8. Filter Reset

Displays the status of the water ﬁlter. To reset the ﬁlter, press and hold FILTER

RESET for 3 seconds. After countdown, the “Replace Filter” indicator will turn off.

Replace Filter

Replace the water ﬁlter. While you are dispensing water, the “Replace Filter”

icon will ﬂash constantly from beginning to the end of dispensing. After 14 days without replacing the water ﬁlter, the “Replace Filter” icon will blink seven times and an alert tone will sound three times at the end of dispensing. See the “Water Filtration System” section. NOTE: “Replace Filter” will remain illuminated if a ﬁlter reset is not completed.

Order Filter

Order a replacement water ﬁlter.

INTRODUCTION | 9

INTRODUCTION

7. 8.

1. 2. 3.

6.5.

FREEZER CONTROLS

1. Pure Freeze® Feature

Pure Freeze® feature is activated automatically when

the freezer is at its lowest setting. The Pure Freeze® setting reduces freezer burn.

Viewing and Adjusting

Temperature

When you ﬁrst install your freezer, make sure that the control is still set to the recommended temperature. The factory recommended setting is -2°F (19°C) for the freezer.

Touch - or + to select a temperature setting.

2. Activate Temperature Mode for

Freezer Deli Drawer

Touch Assorted, Spirits, or DeepFreeze to select a zone temperature setting.

10 | INTRODUCTION

3. Cooling Zones

Select features of your freezer are tied to the perimeter lighting. Press the zone keys to light the corresponding zones in your freezer.

INTRODUCTION

4. Max Ice

The Max Ice Setting increases

the freezer cooling capacity improving the ice making rate.

Ice Maker Off

To turn the ice maker off, touch ICE MAKER OFF.

5. Connect

Wi-Fi connectivity allows your Smart Freezer to connect

to the Internet and interact with the JennAir® App from

your smartphone or mobile device. See the

“Automatic Setup—Wi-Fi Protected Setup

(WPS)” section for more information.

Sabbath

Allows the door of the freezer

to be opened or closed during the Sabbath or other religious holidays without

activating the interior lights or controls. Press and hold Sabbath for 3 seconds to activate Sabbath mode.

Lock

The dispenser can be locked

for easy cleaning or to avoid unintentional dispensing.

6. Power Outage

The Power Outage indicator

lets you know if the power

supply to the freezer has been off and the freezer temperature has risen.

Over temp Alarm

Helps avoid food spoilage

and high energy costs by

sounding an alert when freezer temperatures remain at unusually high levels.

Door Open

The Door Open alarm feature

sounds an alarm when the

refrigerator door(s) or freezer

7. Showroom

This mode is used when the

freezer is on display in a retail store or if you want to turn the cooling off and

deactivate all other functions except interior

lighting.

To activate showroom mode, press and hold top and bottom zone icons

simultaneously for 3 seconds.

To deactivate the showroom mode, press and hold top and bottom zone

icons simultaneously for 3 seconds.

8. Filter Reset

Displays the status of the water ﬁlter. To reset the ﬁlter, press and hold FILTER

RESET for 3 seconds. After countdown, the “Replace Filter” indicator will turn off.

Replace Filter

Replace the water ﬁlter.

While you are dispensing

water, the “Replace Filter”

icon will ﬂash constantly from beginning to the end of dispensing. After 14 days without replacing the water ﬁlter, the

“Replace Filter” icon will blink seven times

and an alert tone will sound three times at the end of dispensing. See the “Water Filtration System” section. NOTE: “Replace Filter” will remain illuminated if a ﬁlter reset is not completed.

Order Filter

Order a replacement water ﬁlter.

INTRODUCTION | 11

GETTING STARTED

BEFORE USE

Before using your refrigerator, all packaging materials should be removed and the interior should be cleaned.

 Remove tape and glue residue from

surfaces before turning on the refrigerator. With your ﬁngers, rub a small amount of liquid dish soap over any adhesive and wipe with warm water to remove.

 Do not use sharp instruments, rubbing

alcohol, ﬂammable ﬂuids, or abrasive cleaners to remove tape or glue. These can damage the surfaces of your refrigerator.

 Dispose of and/or recycle all packaging

materials.

 After all packaging materials have

been removed, clean the inside of your refrigerator.

 Flush 3 gallons (11.4 L) of water through

the water system to clear air from the water line and to keep the dispenser from dripping and/or avoiding decreased dispenser ﬂow. NOTE: If the ﬁlter is not installed correctly, water may dispense at a lower ﬂow rate and there will be slower ice production. Improper ﬁlter installation may also cause the water ﬁlter housing to leak.

SMART FEATURES

Smart Features help make your every day a little more efﬁcient by letting you remotely monitor, manage, and maintain your refrigerator.

REMOTE TEMPERATURE CONTROL What it does: Allows you to control the

temperature of your refrigerator remotely from your mobile device via the JennAir® App.

What it does for you: Lets you control temperatures in your refrigerator, freezer, and temp-controlled pantry remotely—not just when you are standing in front of it.

WATER FILTER STATUS What it does: Gives you a look at the life

remaining for your air and water ﬁlters before a replacement is needed.

What it does for you: Helps you be more efﬁcient in planning for, ordering, and replacing ﬁlters.

AUTO REORDER What it does: Allows you to order replacement

ﬁlters, consumables, and accessories via the JennAir® App for delivery directly to your home.

What it does for you: Simpliﬁes ordering correct water and air ﬁlters—no trips to the store and searching for the correct ﬁlters.

OVER TEMPERATURE What it does: Sends you a notiﬁcation when

the temperature in your refrigerator reaches and rises above a speciﬁed value in the refrigerator and freezer compartments.

What it does for you: Alerts you to overtemperature status to provide input regarding disposition of refrigerator/freezer contents.

MAX COOLREFRIGERATOR What it does: Allows you to control your

refrigerator remotely from your mobile device via the JennAir® App.

What it does for you: Lets you turn on/off Max Cool options remotely to make temperatures colder in the refrigerator in anticipation of loading newly purchased grocery items.

MAX ICEFREEZER What it does: Allows you to control your freezer

remotely from your mobile device via the JennAir® App.

What it does for you: Makes fresh-tasting ice to accommodate your entertainment needs - up to 4 pounds in 24 hours.

PURE FREEZE® MODE What it does: Allows you to receive status

of your refrigerator remotely to your mobile device via the JennAir® App.

What it does for you: Indicates when temperatures are adjusted down to a deep freeze level to reduce freezer burn and helps frozen items maintain their appearance and taste.

12 | GETTING STARTED

GETTING STARTED

SMART FEATURES CONT.

SABBATH MODE What it does: Allows the door of the refrigerator

or freezer to be opened or closed during the Sabbath or other religious holidays without activating the interior lights or controls. Allows you to turn on and off remotely from your mobile device via the JennAir® App.

What it does for you: Lets you turn on/off Sabbath mode options remotely.

DOOR OPEN ALERT What it does: Sends you a notiﬁcation when

the door of the appliance has been left open. What it does for you: Alerts you to door ajar

status so you can close the door(s) or call home to ask someone else to close the door before an over-temp situation arises.

POWER OUTAGE What it does: Sends you a notiﬁcation when

power to your refrigerator goes out, returns, or highest temperature is reached.

What it does for you: Alerts you to power status and disposition of the appliance contents.

SMART GRID

This product has WiFi capability and requires Internet connectivity and a wireless router to enable interconnection with an Energy Management System, and/or with other external devices, systems, or applications.

GETTING STARTED

GETTING STARTED | 13

GETTING STARTED

AUTOMATIC SETUPWIFI PROTECTED SETUP WPS

YOU WILL NEED:

A home wireless router capable of WPS (Wi-Fi protected Setup). The router should be on and have a live internet connection.

To use this feature you need:

 A smartphone running Android 4.3 (or

higher) with a 1280x720 (or higher) screen or a tablet or a smartphone running iOS 8 (or higher).

 A wireless router 2.4 Ghz Wi-Fi b/g/n

connected to internet (verify with your smart device that the signal of your home wireless network is strong close to the appliance).

 The Smart Appliance Identiﬁcation Number

(SAID) from your refrigerator. This is located on a sticker on the inside of the water ﬁlter door.

SAID:

0123456789

MAC ID:

88:E7:12:XX:YY:ZZ

NOTE: If your home wireless router is not equipped with a WPS button, please check the user manual of your router to conﬁrm if it is WPS capable. If not, alternate setup instructions are at www.jennair.com/connect.

Contains FCC ID: Contains IC:

10248A-WICHIN01

A5UWICHIN01

1. Set up router

INTERNET

WI-FI PROTECTED

SETUP (WPS)

HOME WIRELESS

ROUTER

Press the WPS button on the router. An indicator light will begin blinking.

NOTE: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe, or you will need to reinitiate WPS.

2. Set up refrigeration appliance

(time-sensitive step)

Press and hold CONNECT on the control panel for 3 seconds.

The Wi-Fi status indicator ( ) on the appliance control panel will blink slowly while

your appliance and router attempt to connect. If the connection is successful, the Wi-Fi status indicator will illuminate and remain lit.

IF YOUR APPLIANCE DOESN’T CONNECT:

If your appliance and router fail to connect after 2 minutes, the Wi-Fi status indicator will blink rapidly for 5 seconds and then turn off. Check any connection instructions for your speciﬁc router, and refer to alternate instructions at

www.jennair.com/connect. NOTE: If this is your ﬁrst smart appliance, you

will need to download the JennAir® App and create an online user account.

If you already have the app and a user account, please skip ahead to Step 4, “Register your refrigerator in your user account.”

14 | GETTING STARTED

GETTING STARTED

AUTOMATIC SETUPWIFI PROTECTED SETUP WPS CONT.

DISCONNECT AND RECONNECT WIFI

To disconnect Wi-Fi, press and the hold CONNECT for 7 to 15 seconds. The Wi-Fi status indicator will turn off, indicating that you have disabled Wi-Fi.

To reconnect Wi-Fi, press and hold CONNECT for 3 seconds on the control panel.

 The Wi-Fi status indicator ( ) on the

appliance control panel will blink slowly while your appliance and router attempt to connect.

 If the connection is successful, the Wi-Fi

status indicator will illuminate and remain lit.

DISCONNECT AND RECONNECT ROUTER

 To disconnect your refrigerator from your

router, press and hold CONNECT for more than 15 seconds. The Wi-Fi indicator will turn off, indicating that your refrigerator is completely disconnected from Wi-Fi and your router.

 To reconnect your appliance to your router

and reconnect Wi-Fi, press and hold CONNECT for 3 seconds.

The Wi-Fi status indicator ( ) on the appliance control panel will blink slowly while your refrigerator and router attempt to connect.

If the connection is successful, the Wi-Fi status indicator will come on and remain lit.

Press the WPS button on the router. An indicator light will begin blinking.

NOTE: The WPS function on your router is active for 2 minutes. Complete the next step within that timeframe or you will need to reinitiate WPS.

3. Download JennAir

account

From your mobile device, smartphone, or tablet, go to www.jennair.com/connect and follow the instructions to download and install the JennAir® App.

Once installed, tap the JennAir® App icon to open the app. You will be guided through the steps to set up a user account. The App will make sure to get the necessary personal and home information as well as information about your energy company.

App and set up user

4. Register your refrigerator in your user

account

Registering your refrigerator in your account is a necessary step in order for you to take full advantage of the Smart features. When prompted by the app, enter the SAID (casesensitive), which can be found on a sticker on the inside of the water ﬁlter door.

My Smart Appliance ID# is:

_________________________________________________

The Wi-Fi status indicator on the refrigerator

control panel will blink slowly while your refrigerator and router attempt to connect.

NOTE: This blinking only applies to ﬁrst-time registration after provisioning. Blinking will not occur for automatic reconnection after a connection is established.

 Once you’ve connected your refrigerator

to your home Wi-Fi network, it will remain linked even if the power goes out, you move the appliance, or if you put it in storage.

 If you replace your wireless router or get a

different Smart appliance, you will need to repeat this connectivity set-up process.

GETTING STARTED | 15

GETTING STARTED

MANUAL SETUP FIRSTTIME USE

 ACCESS POINT METHOD

This procedure uses Micro Access Point technology and is applicable if your router does not support WPS.

1. Before starting the Setup procedure, please

take note of the home wireless network name (SSID), its password and the SAID of appliance. These will be required during the installation process.

2. Turn on your router and make sure the

internet connection is working.

3. On your appliance, activate the provisioning

process using the AP method. You should see the Wi-Fi icon blinking on the appliance HMI.

4. Turn on your smart device (phone or tablet)

and access your list of available wireless networks in the settings menu.

5. The appliance has created a wireless

network (SSID). Select this network from the list of available wireless networks. The network name is made up of the preﬁx from your appliance type (e.g. washer, dryer, etc.) followed by the MAC address (ex. REFRID_88_E7_12_B3_66_ C3). If you don’t see it, you may need to refresh the list of networks or verify the Wi-Fi icon is on the appliance display.

6. Once you have selected the SSID, a

password will be required. Use the SAID as a password (i.e., 444441ABCD).

NOTE: This password is case-sensitive.

7. Connect to the network.

8. Wait until your device is conﬁrmed to be

connected to the appliance Wi-Fi network.

9. Open a web browser. If nothing appears,

type “192.168.10.1” in the address bar (URL) and press Enter. The browser displays a Smart web page. It is the conﬁguration page of the Wi-Fi radio of your appliance.

10. In the drop-down list of available networks,

select the name of your home wireless network.

11. If your home wireless network is hidden,

select “Other” and manually enter its name (SSID) and security protocol.

WPA2

12. Enter the password for your home wireless

network, if required, and submit. Remember, this kind of password is casesensitive.

13. Click the “ ” button to submit, and wait a

few seconds.

14. The Wi-Fi icon on the appliance should stop

blinking and turn on permanently once connected. Otherwise, disconnect and reconnect the appliance to the main power and repeat the procedure.

15. The Setup process is complete.

16 | GETTING STARTED

GETTING STARTED

SHELVES

The shelves in your appliance are adjustable to meet your individual storage needs.

Storing similar food items together in your appliance and adjusting the shelves to ﬁt different heights of items will make ﬁnding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open and save energy.

Important information to know about glass shelves and covers:

Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-sized pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.

TO REMOVE AND REPLACE THE SHELF AND SHELF SUPPORTS:

1. Remove the shelf by tilting it up at the front

and lifting it out of the shelf supports. Pull the shelf straight out.

2. To replace the shelf, reposition the shelf

supports in the desired location. Check that they are level and ﬁrmly inserted in the support rails.

3. Place the back of the shelf in the shelf

supports.

4. Lower the front of the shelf and make sure

that it is positioned correctly.

DELICRISPER DRAWERS

TO REMOVE AND REPLACE THE DELICRISPER DRAWERS:

1. To remove the deli/crisper drawers, press

the clips located at the bottom of the drawer.

2. Lift up on the drawer and pull straight out.

1. To replace the deli/crisper drawers, extend

the glides to their fullest extent.

2. Using your ﬁngers, hold the glides in place

as you place the drawer back on the glides.

GETTING STARTED

GETTING STARTED | 17

CARE AND CLEANING

CLEANING

Explosion Hazard

Failure to do so can result in death,

Below are the recommended steps to clean your appliance.

1. Press the power switch to OFF.

A. To access the power switch, remove the toe kick by pulling out to release it from the brackets.

3. Hand wash, rinse, and dry removable

parts and interior surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.

 Do not use abrasive or harsh cleaners

such as window sprays, scouring cleansers, ﬂammable ﬂuids, cleaning waxes, concentrated detergents, bleaches, or cleansers containing petroleum on plastic parts, interior, door liners, or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.

 To help remove odors, you can wash

interior walls with a mixture of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).

4. Wash stainless steel and painted metal

exteriors with a clean sponge or soft cloth and a mild detergent in warm water. Do not use abrasive or harsh cleaners, or cleaners containing chlorine. Dry thoroughly with a soft cloth.

5. Press the power switch to ON.

6. To replace, press the toekick panel onto

the toekick bracket to engage the gripping pads.

LEATHER PANEL CARE

Under normal usage conditions, regular dusting and vacuum cleaning in crevices or bottoms is all that is necessary to clean the leather panel.

For minor spots, wipe any excess liquid up immediately with a clean absorbent cloth or sponge. If necessary, use a lightly moistened cloth with clean lukewarm water and let dry naturally.

NOTE:

 Using hairdryer for drying may damage

leather panel, so do not dry using hairdryers.

 Do not use saddle soap, cleaning solvents,

furniture polish, oils, varnish, abrasive cleaners, detergent soaps, or ammonia on leather panel.

2. Remove all removable parts (such as

shelves and crispers) from the inside of the appliance.

18 | CARE AND CLEANING

CARE AND CLEANING

VACATION CARE

1. Remove all food from the

refrigerator/freezer.

2. Empty the ice bin.

3. Turn the power switch to Off.

A. To access the power switch, remove the toekick by pulling out to release it from

the brackets.

B. To replace, press the toekick panel onto the toekick bracket to engage the gripping pads.

4. Clean refrigerator/freezer, wipe it, and dry

well.

5. Tape rubber or wood blocks to the tops of

both doors to prop them open far enough for air to get in. This stops odor and mold from building up.

POWER INTERRUPTIONS

If the power will be out for 24 hours or less, keep the door closed to help food stay cold and frozen.

If the power will be out for more than 24 hours, do one of the following:

 Remove all frozen food and store it in a

frozen food locker.

 Place 2 lbs (907 g) of dry ice in the freezer

for every cubic foot (28 L) of freezer space. This will keep the food frozen for 2 to 4 days.

 If neither a food locker nor dry ice is

available, consume or can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially ﬁlled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and ﬂavor may be affected. If the condition of the food is poor, dispose of it.

CARE AND CLEANING

CARE AND CLEANING | 19

CARE AND CLEANING

REPLACING THE WATER FILTER

The water ﬁlter should be replaced every 6 months based on a ﬂow rate of

0.75 gpm-0.80 gpm (1.89- 2.27 Lpm) that ﬁlters 200 gallons (757 L) of water.

NOTE: If the ﬁlter is not installed correctly, water may dispense at a lower ﬂow rate and there will be slower ice production. Improper ﬁlter installation may also cause the water ﬁlter housing to leak.

1. To open, push the water ﬁlter door up,

which is located at the upper left above the refrigerator or freezer compartment.

2. Turn the water ﬁlter 90° counterclockwise

to unlock.

3. Pull the ﬁlter out of the housing.

4. Remove the water ﬁlter cap from the water

ﬁlter.

20 | CARE AND CLEANING

+ 44 hidden pages