www.dexpress.com DIMENSION EXPRESS Fax on Demand (775) 833-3600
This Data Sheet Includes Information On
Jenn-Air
• Product Model Number (s): •
JJW9730ADB, JJW9730ADW and JJW9730ADS
• Dimensions (Actual Size) •
Oven overlap distances when using cutout
dimensions listed above:
30" Electri Ovens:
Width:
Height:
Penetration into cabinet opening:
Distance from cabinet face to
outer edge of handle:
Oven body width:
Oven body height:
Oven body depth:
Cutout Width:
Cutout height:
Cutout Depth:
Top overlap: 5/16"
Bottom overlap: 5/16"
Right overlap: 11/16"
Left overlap:11/16"
29 7/8"
18 7/8"
22 13/16"
1 5/8"
28"
18 1/8"
22 13/16"
28 1/2"
18 1/2"
23"
Overall Dimensions
(not to scale)
28"
18 7/8"
18 1/8"
• Additional Information •
• Cutout height and width are ± 1/16".
• Cutout in cabinet should be level and straight. There
are no provisions to level the unit after it is installed.
• Construct 5/8" minimum plywood floor flush with
bottom of opening. Floor must be level and straight and
capable of supporting 200 lbs.
• A three-wire, single phase, A.C. 120/208-240 volt,
60Hz cycle electrical system must be provided (Load
30 amps @ 120/240VAC). 40 amp circuit
recommended. 7/8" O.D. flexible cable 4 feet long is
furnished by manufacturer. Mount junction box in area
under plywood floor if adequate lower cabinet space is
available. Locate 1 1/4" conduit access hole in the left
hand side of the back wall (3" from the left side and 3
1/2" up from bottom.
See page 2 for additional information
Subject to change without notice. This system is designed to
be updated daily if necessary. Dimension Express is not
responsible for use of superseded, voided, or outdated data
sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall
not exceed $50.00.
Copyright © Dimension Express, 2000.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
231
22 13/16"
Air Intake"
1 5/8"
BN207.5 • A231B149 • 31469 • 002908 • 203716 • 43270
29 7/8"
www.dexpress.com
DIMENSION EXPRESS
Fax on Demand (775) 833-3600
Additional Information:
• Centerline of cabinet is not the centerline of the oven face. The
cutout is offset by 5/16" to the right as you face the cutout.
• Allow for 15/16" face trim overlap on each side.
• Do NOT block air intake vents at bottom of oven.
• Gas or electric cooktop may be installed over oven. there must be a
minimum of 1" clearance between top of oven and bottom of cooktop
burner box.
Page 2
This Data Sheet Includes Information On
Jenn-Air
• Product Model Number (s): •
30" Electri Ovens:
JJW9730ADB, JJW9730ADW and JJW9730ADS
Cabinet Opening
(not to scale)
25" normal counter top depth
1 1/4" Dia conduit access hole as close
to the rear right corner as possible or in
adjacent right side compartment.
23"
18 1/2"
1 1/2" countertop
5/8" plywood bottom must
28 1/2"
support 200 pounds
36" standard countertop height
1 1/2" countertop thickness
Recommended cutout:
24"
36" countertop height recomended
28 1/2" wide by 18 1/2" high
Subject to change without notice. This system is designed to be updated daily if necessary. Dimension Express is not responsible for use of superseded, voided, or
outdated data sheets. Because of the difficulty or impracticability of determining actual damages, liability of Dimension Express shall not exceed $50.00.
Copyright © Dimension Express, 2000.
• NEVER reuse Data Sheets. Data Sheets are subject to change without • Call Dimension Express if you have any questions at (775) 833-3633 •
notice. Dimension Express is a FREE service bureau and is updated daily, • Always refer to a current Code at a Glance or manufacturer directory •
it makes far more sense to spend the time necessary to request new Data • Data Sheet codes change on the first of odd numbered months at 12:01am •
Sheets for each project, as opposed to the problems, time, costs, and risks
associated with reusing old Data Sheets.
BN207.5 • A231B149 • 31469 • 002908 • 203716 • 43270
149