INSTALLATION INSTRUCTIONS
27" (68.6 CM), AND 30" (76.2 CM) INDOOR/OUTDOOR
ELECTRIC WARMING DRAWER
INSTRUCTIONS D’INSTALLATION
TIROIR-RÉCHAUD ÉLECTRIQUE POUR USAGE INTÉRIEUR/ EXTÉRIEUR DE 27" (68,6 CM), ET 30" (76,2 CM)
Table of Contents/Table des matières
WARMING DRAWER SAFETY....................................................... |
2 |
INSTALLATION REQUIREMENTS................................................. |
3 |
Tools and Parts............................................................................. |
3 |
Location Requirements................................................................. |
3 |
Electrical Requirements................................................................ |
6 |
INSTALLATION INSTRUCTIONS................................................... |
6 |
Install Warming Drawer................................................................. |
6 |
Complete Installation.................................................................... |
7 |
CUSTOM DRAWER FRONT INSTALLATION INSTRUCTIONS |
|
FOR WARMING DRAWERS........................................................... |
7 |
Tools and Parts............................................................................. |
7 |
Install Custom Drawer Front Panel............................................... |
7 |
SÉCURITÉ DU TIROIR-RÉCHAUD................................................ |
9 |
EXIGENCES D’INSTALLATION.................................................... |
10 |
Outillage et pièces...................................................................... |
10 |
Exigences d’emplacement......................................................... |
10 |
Electrical Requirements.............................................................. |
13 |
INSTRUCTIONS D’INSTALLATION............................................. |
13 |
Installation du tiroir-réchaud....................................................... |
13 |
Achever l’installation................................................................... |
14 |
INSTRUCTIONS D’INSTALLATION DE LA FAÇADE DU TIROIR |
|
PERSONNALISÉ POUR TIROIR-RÉCHAUD.............................. |
14 |
Outillage et pièces...................................................................... |
14 |
Installation du panneau de la façade du tiroir personnalisé...... |
14 |
IMPORTANT:
Save for local electrical inspector’s use.
IMPORTANT:
À conserver pour consultation par l’inspecteur local des installations électriques.
W11295554A
WARMING DRAWER SAFETY
2
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Tools Needed
■■ Phillips screwdriver ■■ Flat-blade screwdriver ■■ Measuring tape
■■ Level
■■ Drill
■■ 13/8" (3.5 cm) hole saw
Parts Supplied
■■ Two #8-18 x 1/2" (1.3 cm) screws
■■ Lens (for panel ready models)
Check local codes. Check existing electrical supply. See “Electrical Requirements.”
It is recommended that all electrical connections be made by a licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
■■ Cutout dimensions that are shown must be used. Given dimensions provide minimum clearance with warming drawer.
■■ Recessed installation area must provide complete enclosure around the recessed portion of the warming drawer.
■■ Grounded electrical supply is required. See “Electrical Requirements” section.
■■ Electrical supply outlet should be located in the rear wall on the upper right-hand side of the cutout or in an adjacent cabinet. The outlet must be recessed. If the electrical outlet is located in an adjacent cabinet, a 13/8" (3.5 cm) minimum diameter hole should have been drilled in the back of the cutout or support surface to pass the power supply cord through to the outlet.
■■ Warming drawer support surface must be solid, level,and flush with bottom of cabinet cutout.
■■ Warming drawers with oiled bronze, black glass, and white glass panels are approved for indoor use only.
■■ Support surface must be solid, level, and flush with the bottom of the cabinet cutout.
■■ 24" (61.0 cm) minimum cabinet depth.
For best performance results make sure the warming drawer is leveled before completing installation. There is no way to level the warming drawer after it has been installed. If the installation is not level, the door may slide open or not seal tightly, allowing heat to escape.
NOTE: If installing the warming drawer below another product, refer to that product’s literature for any installation requirements.
Product Dimensions
B
A
|
|
|
|
C |
|
|
|
E |
|
|
|
|
|
|
|
D |
|
|
|
|
WARMING |
OVEN DEPTH |
RECESSED |
RECESSED |
OVERALL |
DRAWER |
|
FRONT HEIGHT |
||||||
DRAWER SIZE |
(A) |
WIDTH (B) |
HEIGHT (C) |
WIDTH (D) |
||
(E) |
||||||
|
|
|
|
|
||
27" (68.6 cm) |
231/8" (58.7 cm) |
251/4" (64.1 cm) |
9" (22.9 cm) |
263/4" (67.9 cm) |
101/4" (26.1 cm) |
|
30" (76.2 cm) |
231/8" (58.7 cm) |
281/4" (71.8 cm) |
9" (22.9 cm) |
293/4" (75.6 cm) |
101/4" (26.1 cm) |
3
Clearance Dimensions |
|
|
|
|
|
|
|
|
Front view |
|
|
|
|
120 V |
|
|
|
|
|
grounded |
|
|
|
|
|
outlet |
|
|
|
|
|
(or located |
|
|
|
|
|
in adjacent |
|
|
|
|
|
cabinet) |
|
|
|
|
|
|
A |
|
|
|
|
|
B |
|
|
|
|
Warming |
|
|
|
|
|
drawer |
A |
|
|
|
|
cutouts |
|
|
|
|
|
|
|
|
|
|
|
|
B |
|
|
|
|
Toe |
C |
|
|
|
|
kick |
D |
|
|
|
|
|
|
|
|
|
|
|
E |
|
|
WARMING |
MINIMUM |
CUTOUT |
MINIMUM/ |
CUTOUT |
MINIMUM |
DRAWER SIZE |
BETWEEN |
HEIGHT (B) |
RECOMMENDED (C) |
WIDTH (D) |
CABINET |
|
CUTOUTS (A) |
|
|
|
WIDTH (E) |
27" (68.6 cm) |
21/2" (6.4 cm) |
91/8" (23.2 cm) |
1" (2.5 cm)/ |
251/2" (64.8 cm) |
27" (68.6 cm) |
|
|
|
41/4" (10.8 cm) |
|
|
|
|
|
|
|
|
30" (76.2 cm) |
21/2" (6.4 cm) |
91/8" (23.2 cm) |
1" (2.5 cm)/ |
281/2" (72.4 cm) |
30" (76.2 cm) |
|
|
|
41/4" (10.8 cm) |
|
|
Warming drawer can be installed as an indoor single or double installation or installed under a single oven. Two warming drawers under a single oven are shown.
NOTE: The warming drawer cannot be leveled after being installed.
For outdoor installation, follow the cutout dimensions above. Install the outdoor warming drawer in a permanent fixture.
Custom Wood Drawer Front
If you plan to install a custom wood panel to match your cabinets, we recommend consulting a qualified cabinetmaker or carpenter. The back of the wood panel must be sealed to avoid moisture damage.
4
Clearance Dimensions - Flush Installation
Front View |
Side View |
Cabinet
Back
F |
|
|
Top View |
|
A |
|
|
|
1" (25 mm) |
|
B |
|
|
|
|
|
Side Cleats* |
e |
C |
|
7/8" (22 mm) |
|
||
|
|
|
|
Platform* |
|
|
|
|
|
E |
F |
|
|
|
|
|
|
D |
|
|
|
Side Cleat* |
|
|
|
1⁄" (4.1 cm) |
|
|
|
27" (68.6 cm) |
30" (76.2 cm) |
|
|
|
Models |
Models |
|
A |
Width of flush inset cutout (minimum) |
271/4" (69.2 cm) |
301/4" (76.8 cm) |
|
|
|
|
|
|
B |
Height between cutouts (minimum) |
21/2" (6.4 cm) |
21/2" (6.4 cm) |
|
|
|
|
|
|
C |
Height of flush inset cutout (minimum) |
103/4" (27.3 cm) |
103/4" (27.3 cm) |
|
|
|
|
|
|
D |
Bottom of cutout to floor (recommended) |
81/4" (21.0 cm) |
81/4" (21.0 cm) |
|
|
|
|
||
Bottom of cutout to floor (minimum) |
5" (12.7 cm) |
5" (12.7 cm) |
||
|
||||
|
|
|
|
|
E |
Width of opening (minimum) |
251/4" (64.1 cm) |
281/4" (71.8 cm) |
|
|
|
|
|
|
F |
Depth of cutout (minimum) |
25" (63.5 cm) |
25" (63.5 cm) |
|
|
|
|
|
|
e |
Recommended outlet location |
|
|
|
|
|
|
|
Flush Installation Requirements
A 25" (63.5 cm) minimum cutout depth is required.
These dimensions will result in a 1/4" (6 mm) reveal on all sides of the warming drawer.
* The front face of the cleats and platforms will be visible and should be treated as a finished surface.
5
Loading...