Page 1
JENNAIR DETAILED PLANNING DIMENSIONS
SMALL WARMING DRAWERS
JJD3024H – 23M/zn" x 5>/zn" x 22C/,"
PRODUCT DIMENSIONS
A
B
1 of 4
FRONT VIEW
C
D
E
MODEL # JJD3024HM JJD3024HL
in cm in cm
219⁄
217/
16
59.5 237⁄
16
16
16
8
4
14.1 59⁄
54.8 219⁄
54.4 217/
56.8 223⁄
94.6 371⁄
A Overall width (max.) 237⁄
B Overall height (max.) 59⁄
Width of recessed
C
warming drawer
Depth of recessed
D
warming drawer
E Depth with drawer front 223⁄
F Depth with door open 371⁄
F
16
59.5
16
14.1
16
54.8
16
54.4
8
56.8
4
94.56
TOP VIEW
IMPORTANT: Dimensional specications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All JennAir® appliances are appropriately UL, CUL or CSA approved.
W11308123A
Page 2
JENNAIR DETAILED PLANNING DIMENSIONS
SMALL WARMING DRAWERS
JJD3024H – 23M/zn" x 5>/zn" x 22C/,"
DIMENSIONS AS INSTALLED
2 of 4
D
E
Back of
Cabinet
F
A
B
Bottom of
Cutout
C
SIDE VIEW
MODEL # JJD3024HM JJD3024HL
in cm in cm
A Height to top of drawer (max.) 4¾ 12.1 4¾ 12.1
B Height of drawer extending below cutout 1/2 1.19 1/2 1.19
C Height of recessed warming drawer 51⁄
D Depth with door open 371⁄
E Depth with drawer front 223⁄
F Depth of recessed warming drawer 217⁄
16
4
8
16
12.9 51⁄
94.6 371⁄
56.8 223⁄
54.4 217⁄
G Power cord envelop height 11/16 1.8 11/16 1.8
16
4
8
16
12.9
94.6
56.8
54.4
IMPORTANT: Dimensional specications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All JennAir® appliances are appropriately UL, CUL or CSA approved.
Page 3
JENNAIR DETAILED PLANNING DIMENSIONS
SMALL WARMING DRAWERS - STANDARD INSTALLATION
JJD3024H – 23M/zn" x 5>/zn" x 22C/,"
3 of 4
OPENING/CLEARANCE DIMENSIONS
A
B
C*
e
MODEL # JJD3024HM JJD3024HL
in cm in cm
A Width of cabinet (min.) 235⁄
B Width of cutout 2111⁄
C* Height of cutout 2215⁄
D Depth of cutout (min.) 2111⁄
8
16
16
16
60 235⁄
55 2111⁄
58.2 2215⁄
55 2111⁄
8
16
60
55
16
58.2
16
55
e Recommended outlet location
*Height for installation of JJD3024 under JJW6024, JMC6224 or JJB6424
FRONT VIEW
Back of Cabinet
D
SIDE VIEW
Power cord location
BACK VIEW
IMPORTANT: Dimensional specications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All JennAir® appliances are appropriately UL, CUL or CSA approved.
Page 4
JENNAIR DETAILED PLANNING DIMENSIONS
Back of Cabinet
E
E
Side Cleat*
Side Cleat*
25/31" (20.5 mm) for NOIR and
26/31" (21.3 mm) for RISE
SMALL WARMING DRAWERS - FLUSH INSTALLATION
JJD3024H – 23M/zn" x 5>/zn" x 22C/,"
OPENING/CLEARANCE DIMENSIONS
MODEL # JJD3024HM JJD3024HL
A Width of ush
inset cutout (min.)
B Width of opening
(min.)
C* Height of opening
(min.)
D Height of ush
inset cutout (min.)
E Depth of cutout
(min.)
e Recommended outlet location
*Height for installation of JJD3024 under JJW6024, JMC6224 or JJB6424
in cm in cm
16
2311⁄
16
2111⁄
16
2315⁄
4
233⁄
16
2111⁄
- 221⁄255 - 57.2 2111⁄
60.2 2311⁄
55 2111⁄
58.2 2315⁄
60.3 233⁄
16
16
16
4
-
16
229⁄1655 - 57.3
4 of 4
60.2
55
58.2
60.3
C*
FRONT VIEW
SIDE VIEW
D
A
B
25
(20 mm)
"
32
/
/
Plat
64
"
(10 mm)
form*
Side Cleats*
25
ELECTRICAL REQUIREMENTS
120 V, 60 Hz, AC only, 15 A fused, electrical circuit is required. A
dedicated circuit is recommended.
If the outlet is on the rear wall behind the warming drawer, it must be
recessed and located in the upper right-hand corner. If outlet is located
in an adjacent cabinet, drill a 13⁄8" (3.5 cm) minimum diameter hole in the
side wall or support surface to access the power supply cord.
LOCATION REQUIREMENTS
e
Support surface must be solid, level and ush with the bottom of the
cabinet cutout.
The warming drawer must be leveled before completing installation.
FLUSH INSTALLATION REQUIREMENTS
A 229⁄16" (57.3 cm) minimum cutout depth is required.
These dimensions will result in a 1/8" (3 mm) reveal on all sides of the
warming drawer.
The front face of the cleats and platforms will be visible and should be
treated as a nished surface.
Power cord location
BACK VIEW
IMPORTANT: Dimensional specications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All JennAir® appliances are appropriately UL, CUL or CSA approved.
®/™ ©2019 JennAir. All rights reserved.
TOP VIEW
*Cleats and platform must be recessed 13/16" (2.1 cm) for NOIR and
7/8" (2.2 cm) for RISE from the front of the cabinet.
Installation Instruction W11260097
W11308123A
Loading...