Jenn-Air JGD3536WB00, JGD3536WS00, JGD3536WW00 Installation Guide

_]ENN-AIRo

30" (76.2 CM) AND 36" (91.4 CM) GAS DOWNDRAFT

COOl(TOP INSTALLATION INSTRUCTIONS

INSTRUCTIONSD'INSTALLATIONDELATABLEDE

CUISSON A GAZ A ASPIRATION PARLEBAS

DE30" (76,2 CM) ETDE 36" (91,4 CM)

Table of Contents/Table des mati_res

COOKTOP SAFETY ........................................................................ 1

INSTALLATION REQUIREMENTS ................................................ 3

Tools and Parts ............................................................................ 3

Location Requirements ................................................................ 3

Venting Requirements .................................................................. 5

Venting Methods .......................................................................... 6

Electrical Requirements ............................................................... 7

Gas Supply Requirements ........................................................... 8

INSTALLATION INSTRUCTIONS .................................................. 9

Install Cooktop ............................................................................. 9

Rotate Blower - Optional .............................................................. 9

Make Gas Connection ................................................................ 10

Electronic Ignition System .......................................................... 12

Complete Installation .................................................................. 12

SECURITE DE LA TABLE DE CUISSON ................................. 13

EXIGENCES D'INSTALLATION ................................................ 14

Outillage et pieces ................................................................... 14

Exigences d'emplacement ...................................................... 14

Exigences concernant I'evacuation ........................................ 16

Methodes d'evacuation ........................................................... 17

Specifications electriques ....................................................... 19

Specifications de I'alimentation en gaz .................................. 19

INSTRUCTIONS D'INSTALLATION ......................................... 21

Installation de latable de cuisson ........................................... 21

Rotation du ventilateur- Facultative ....................................... 21

Raccordement au gaz ............................................................. 22

Systeme d'allumage electronique ........................................... 24

Achever I'installation ............................................................... 24

COOKTOP SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

iMPORTANT:

installer: Leave installation instructions with the homeowner.

Homeowner: Keep installation instructions for future reference.

iMPORTANT :

Installateur : Remettre les instructions d'installation au propri6taire.

Propri6taire : Conserver les instructions d'installation pour r6f6rence ult_rieure.

W10197058A

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance,

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier,

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier. If a gas leak is detected, follow the "What to do if you smell gas" instructions.

In the State of Massachusetts, the following installation instructions apply: m Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

m If using a ball valve, it shall be a T-handle type. m A flexible gas connector, when used, must not exceed 3 feet.

INSTALLATIONREQUIREMENTS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed

here. Tools needed

• Tape measure

• Flat-blade screwdriver

• Phillips head screwdriver

• Drill

• Level

• 6" (15.2 cm) socket extension

• Marker or pencil

Parts supplied

• Vent grill • Burner caps

• Pre-filter • Burner grates

• LP conversion kit • Pressure regulator

Parts needed

• Metal ducting

• Vent clamps

• Jenn-Air wall cap Jenn-Air_6 '' (15.2 cm) Round Surface Wall Cap Damper

Order Part Number A406 Jenn-AiP _3W' x 10" (8.3 x 25.4 cm) Surface Wall Cap Damper

Order Part Number A403 To order, see the "Assistance or Service" section of the Use

and Care Guide.

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See "Electrical Requirements" and "Gas Supply Requirements" sections.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

• Pliers

• 1¼. drill bit

• Jigsaw

• Ratchet with 3/8"socket

• Pipe-joint compound resistant to LP gas

• Noncorrosive leak-detection

solution

The cooktop should be installed in a location away from strong draft areas, such as windows, doors and strong heating vents or fans.

All openings in the wall or floor where cooktop is to be installed must be sealed.

Cabinet opening dimensions that are shown must be used. Given dimensions are minimum clearances.

Grounded electrical supply is required. See "Electrical Requirements" section. Proper gas supply connection must be available. See "Gas Supply Requirements" section.

• The cooktop is designed to hang from the countertop by its side or rear flanges.

• The gas and electric supply should be located as shown in "Cabinet Dimensions" section so that they are accessible without requiring removal of the cooktop.

• Provide cutout in right rear corner of cutout enclosure as shown to provide clearance for gas inlet, power supply cord, and to allow the rating label to be visible.

• If cabinet has drawers, drawers will need to be removed and drawer fronts installed on front of cabinet.

IMPORTANT: An undercounter built-in oven cannot be installed under this product.

IMPORTANT; To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage.

Mobile Home - Additional Installation Requirements The installation of this cooktop must conform to the

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, use the Standard for Manufactured

Home Installations, ANSI A225.1/NFPA 501A or local codes.

• In Canada, the installation of this cooktop must conform with the current standards CAN/CSA-A240-1atest edition, or with

local codes.

Product Dimensions

30" (76.2 cm) Cooktop

IMPORTANT; Observe all governing codes and ordinances.

When installing cooktop, use minimum dimensions given.

• It is the installer's responsibility to comply with installation clearances specified on the model/serial rating plate. The

model/serial rating plate is located on side of the downdraft plenum.

• To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

A. 21Y2" (54.6cm) B. 191_,, (50.0 cm) C. Model/serial rating plate location

Cabinet Dimensions

[

A. 30" (76.2 cm)

B. 12 _" (32.9 cm) centerline of

cooktop to centerline of gas

manifold pipe C. 4" (10.2 cm) D. 61_2" (16.8 cm)

E. 18_" (46.8 cm)

G. 12_" (31.8 cm) H. 14" (35.6 cm)

36" (91.4 cm) Cooktop

A. 21V/' (54.6 cm) B. 191_,, (50.0 cm) C. Model/serial rating plate location

A ......................B_

[_-C .... ir °_

A. 36" (91.4 cm) B. 153/4''(40.0 cm) centerline of

cooktop to centerline of gas

manifold pipe C. 4" (10.2 cm) D. 61_2" (16.8 cm) E. 18_" (46.8 cm)

G. 12½" (31.8 cm) H. 13" (33.0 cm)

F. 11H_" (4.3 cm) recommended

minimum cabinet to motor

clearance

I.28¼" (71.4 cm)

F. 10_" (26.4 cm)

recommended minimum

cabinet to motor clearance

I.34_" (87.3 cm)

A. 30" (76.2 cm) on 30" (76.2 cm) models

36" (91.4 cm) on 36" (91.4 cm) models B. Combustible area above countertop (shown by dashed box above) C. 30" (76.2 cm) minimum clearance between top of cooktop platform

and bottom of uncovered wood or metal cabinet (24" [61.0 cm]

minimum clearance if bottom of wood or metal cabinet is covered

by not less than ¼" [0.6 cm] flame retardant millboard covered with

not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless

steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper) D. 13" (33.0 cm) recommended upper cabinet depth

E.2 _" (5.4 cm) F. 191_ '' (50.6cm)

G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop

within minimum horizontal clearances to cooktop

H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of

countertop

I. Junction box or outlet; 10" (25.4 cm) from right-hand side of

cabinet

J. 28_" (72.7cm) on 30" (76.2 cm) models

343/4'' (88.3 cm) on 36" (91.4 cm) models K. 6" (15.2 cm) minimum distance to nearest left and right side

combustible surface above cooktop

L. 1" (2.5 cm) minimum clearance between back wall and countertop

M. Gas line opening - Waft: anywhere 6" (15.2 cm) below underside of

countertop. Cabinet floor: anywhere within 6" (15.2 cm) of rear wall

is recommended. N. 25" (63.5 cm) depth of countertop

NOTES: After making the countertop cutout, some installations may require notching down the base cabinet side walls to clear

the cooktop base. To avoid this modification, use a base cabinet with sidewalls wider than the cutout.

• A minimum side clearance of 6" (15.2 cm) is recommended between side of cooktop and side wall for maximum ventilation performance.

• A minimum clearance of 2" (5.1 cm) is recommended between the motor/blower and cabinet for proper cooling. A

6" (15.2 cm) clearance is recommended for servicing access.

Cutout Dimensions

A. 28 _" (72. 7 cm) maximum on 30" (76.2 cm) models

343/4'' (88.3 cm) maximum on 36" (91.4 cm) models

B. 191%_,,(50.6 cm) maximum on both 30" (76.2 cm) and 36" (91.4 cm)

models

C. 8V2" (21.6 cm) on 30" (76.2 cm) models

17V2" (44.4 cm) on 36" (91.4 cm) models

D. 53/4"(14.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models

E.2 _" (5.4 cm) minimum space to front edge of cooktop

F. Floor exhaust option G. 6_" (15.6 cm) for 6" vent system H. 8V2" (21.6 cm) on 30" (76.2 cm) models

17V2" (44.4 cm) on 36" (91.4 cm) models

I. 16" (40.6 cm) on both 30" (76.2 cm) and 36" (91.4 cm) models

J. Wall exhaust option

n?ng ®c u s m®n'ts

IMPORTANT: This cooktop must be exhausted outdoors unless using the JennmAir®Duct Free Filter Accessory Kit. See "Venting

Methods" section.

• Do not terminate the vent system in an attic or other enclosed area.

• Use a Jenn-Air vent cap.

• Vent system must terminate to the outside.

• Use only a 6" (15.2 cm) round metal vent. Rigid metal vent is recommended. For best performance, do not use plastic or

metal foil vent.

• Before making cutouts, make sure there is proper clearance within the wall or floor for the exhaust vent.

• Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting frame must be

constructed.

• The size of the vent should be uniform.

• The vent system must have a damper. If roof or wall cap has a damper, do not use damper supplied with the range hood.

• Use vent clamps to seal all joints in the vent system.

• Use caulking to seal exterior wall or roof opening around the cap.

• Determine which venting method is best for your application.

For Best Performance:

• Use 26-gauge minimum galvanized or 25-gauge minimum aluminum metal vent. Poor quality pipe fittings can reduce

airflow. Flexible metal vent is not recommended. NOTE: Local codes may require a heavier gauge material.

• Metal duct may be reduced to 30-gauge galvanized steel or 26-gauge aluminized steel if allowed by local codes. This

reduction is based on information in the International Residential Codes Section M1601.1 (2006 edition).

• Do not install 2 elbows together.

• Use no more than three 90° elbows.

• If an elbow is used, install it as far away as possible from the hood's vent motor exhaust opening.

• Make sure there is a minimum of 18" (45.7 cm) of straight vent between the elbows if more than one elbow is used.

• Elbows too close together can cause excess turbulence that reduces airflow.

• Do not use a 5" (12.7 cm) elbow in a 6" (15.2 cm) or 3V4" x 10" (8.3 x 25.4 cm) system.

• Do not reduce to a 5" (12.7 cm) system after using a 6" (15.2 cm) or 3V4" x 10" (8.3 x 25.4 cm) fittings.

• Avoid forming handmade crimps. Handmade crimps may restrict airflow.

• Use a Jenn-Air vent cap for proper performance. If an alternate wall or roof cap is used, be certain the cap size is not reduced and that it has a backdraft damper.

• Use vent clamps to seal all joints in the vent system.

• Use caulking to seal exterior wall or roof opening around the cap.

The length of vent system and number of elbows should be kept to a minimum to provide efficient performance.

The maximum equivalent length of the vent system is 60 ft (18.3 m). For altitudes above 4,500 ft (1272 m), reduce recommended vent run by 20% for best performance.

Cold Weather Installations An additional backdraft damper should be installed to minimize

backward cold air flow and a thermal break installed to minimize conduction of outside temperatures as part of the vent system.

The damper should be on the cold air side of the thermal break. Makeup Air Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your

area.

Commonventingmethodsareshownforacounter-mounted Concrete Slab Installations - Exhaust Through Wall

downdraft cooktop. The cooktop may be vented through the wall or floor. B

Option 1 - Roof Venting Option 2 - Wall Venting

A. Roof cap B. 6" (15.2 cm) round roof venting

Option 3 - Venting Between

Floor Joist

A. 6" (15.2 cm) round wall venting B. Wall cap

Option 4 - Venting behind

Cabinet Kick Plate

A. Wall cap

B. 6" (15.2 cm) round metal vent

C. 16" (40.6 cm) maximum D. 6" (15.2 cm) round PVC sewer pipe

E. 6" (15.2 cm) round metal vent F. 6" (15.2 cm) round PVC coupling

G. Concrete slab H. 6" (15.2 cm) round PVC sewer pipe

I. 6" (15.2 cm) round 90° PVC sewer pipe elbow

J. Tightly pack gravel or sand completely around pipe.

K. 30 ft (9.1 m) maximum

L. 6" (15.2 cm) round 90 ° PVC sewer pipe elbow

M. 6" (15.2 cm) round PVC coupling

N. 12" (30.5 cm) minimum

L L

A. Wall cap B. 6" (15.2 cm) round wall

venting

ii .

(8.3 x 25.4 crn)

A B

A. Wall cap B. 6" (15.2 cm) round wall

venting

Jenn-Air _ Duct Free Filter Accessory Kit On select downdraft models, the Jenn-Air ®Duct Free Filter

Accessory Kit Part Number JDX7000WX is now available. The Jenn-Air ® Duct Free Filter Accessory Kit is ideal for both new construction and kitchen renovation projects because it provides

an easy alternative to the installation of metal ducting and venting in the downdraft system outside the home. The kit includes all required hardware, one filter and complete installation

instructions. For more information on the Jenn-Air ®Duct Free Filter Accessory Kit, contact your Jenn-Air ®dealer or call

1-800-JENNAIR (1-800-536-6247).

Calculating Vent System Length

Tocalculate the length of the system you need, add the equivalent feet (meters) for each vent piece used in the system.

Vent Piece 6" (15.2 cm) Round

Example vent system

90 ° embow

wall cap

6 ft (1.8 m)

45° elbow 2.5 ft

(0.8m)

90° elbow 5.0 ft

(1.5m)

6" (15.2 cm) 0.0 ft wall cap (0.0 m)

31/4"x 10" (8.3 cm x 25.4 cm) 4.5 ft to 6" (15.2 cm) transition (1.4 m)

6" (15.2 cm) to 31/4'' x 10" 1 ft (8.3 cm x 25.4 cm) transition (0.3 m)

31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft to 6" (15.2 cm) 90° elbow (1.5 m)

transition

6" (15.2 cm) to 31/4'' x 10" 5.0 ft (8.3 cm x 25.4 cm) 90° elbow (1.5 m) transition

31/4"x 10" (8.3 cm x 25.4 cm) 5.0 ft 90° elbow (1.5 m)

31/4'' x 10" (8.3 cm x 25.4 cm) 12.0 ft flat elbow (3.7 m)

(

1- 90 ° elbow = 5 ft (1.5 m) 8 ft (2.4 m) straight = 8 ft (2.4 m) 1 - wall cap = 0 ft (0 m) System length = 13 ft (3.9 m)

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure and air turbulence that greatly reduce

performance.

IMPORTANT: The cooktop must be electrically grounded in accordance with local codes and ordinances, or in the absence

of local codes, with the National Electrical Code, ANSl/NFPA 70 or Canadian Electrical Code, CSA (}22.1.

This cooktop is equipped with an electronic ignition system that will not operate if plugged into an outlet that is not properly polarized.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131 m5575

• A 120 volt, 60 HZ, AC only, 15-amp, fused electrical circuit is required. A time-delay fuse or circuit breaker is also recommended. It is recommended that a separate circuit serving only this cooktop be provided.

• Electronic ignition systems operate within wide voltage limits, but proper grounding and polarity are necessary. Check that the outlet provides 120-volt power and is correctly grounded.

• The wiring diagrams are provided with this cooktop. See "Wiring Diagrams" on a separate sheet. Wiring diagrams are located on the left underside of the cooktop base.

31/4'' x 10" (8.3 cm x 25.4 cm) 0.0 ft wall cap (0.0 m)

Flexible metal appliance connector:

• If local codes permit, use a 1/2"or 3/4"I.D. flexible stainless

steel tubing gas connector, designed by CSA to connect the cooktop to the rigid gas supply line.

Explosion Hazard

Use a new CSA International approved gas supply line. Install a shut=off valve.

Securely tighten all gas connections. if connected to LP, have a qualified person make sure

gas pressure does not exceed 14" (36 cm) water

column.

Examples of a qualified person include: licensed heating personnel,

authorized gas company personnel, and authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Observe all governing codes and ordinances. IMPORTANT: This installation must conform with all local codes

and ordinances. In the absence of local codes, installation must conform with American National Standard, National Fuel Gas

Code ANSI Z223.1 -latest edition or CAN/CGA B149 -latest edition.

IMPORTANT: Leak testing of the cooktop must be conducted according to the manufacturer's instructions.

Type of Gas

• A 1/2"male pipe thread is needed for connection to the

female pipe threads of the inlet to the cooktop pressure regulator.

• Do not kink or damage the flexible metal tubing when

moving the cooktop.

Rigid pipe connection: The rigid pipe connection requires a combination of pipe

fittings to obtain an in-line connection to the cooktop. The rigid pipe must be level with the cooktop connection. All strains must be removed from the supply and fuel lines so cooktop will be level and in line.

Must include a shutoff valve: The supply line must be equipped with a manual shutoff

valve. This valve should be located in the same room but external to the cooktop opening, such as an adjacent

cabinet. It must be accessible without removing the cooktop, and itshould be in a location that allows ease of opening and closing. Do not block access to shutoff valve. The valve is for turning on or shutting off gas to the cooktop.

Natural Gas:

This cooktop is design-certified by CSA International for use with Natural gas or, after proper conversion, for use with LP gas.

• This cooktop is factory set for use with Natural gas. If converting to LP gas, see the "LP Gas Conversion" instructions provided in the package containing literature. The model/serial rating plate located on the underside of the cooktop base has information on the types of gas that can be used. If the types of gas listed do not include the type of gas available, check with the local gas supplier.

LP Gas Conversion: Conversion must be done by a qualified service technician.

No attempt shall be made to convert the cooktop from the gas specified on the model/serial rating plate for use with a different gas without consulting the serving gas supplier. See the Gas Conversion instructions provided in the package containing

literature.

Gas Supply Line

Provide a gas supply line of 3/4"(1.9 cm) rigid pipe to the cooktop location. A smaller size pipe on longer runs may

result in insufficient gas supply. Pipe-joint compounds that resist the action of LP gas must be used. Do not use

TEFLON ®ttape. With LP gas, piping or tubing size should be 1/2"minimum. Usually, LP gas suppliers determine the size

and materials used in the system.

A. Gas supply line B. Shutoff valve "open" position C. To cooktop

Gas Pressure Regulator

The gas pressure regulator supplied with this cooktop must be used. The inlet pressure to the regulator should be as follows for proper operation:

Natural Gas: Minimum pressure: 5" (12.7 cm) WCP

Maximum pressure: 7" to 14" (17.8 cm to 35.5 cm) WCP

LP Gas:

Minimum pressure: 11" (27.9 cm) WCP Maximum pressure: 14" (35.5 cm) WCP Contact local gas supplier if you are not sure about the inlet

pressure.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

+ 16 hidden pages