Jenn-Air JGD3430GS User Manual

JENN-AIR® DETAILED PLANNING DIMENSIONSJENN-AIR® DETAILED PLANNING DIMENSIONS

A

A

B

K

L

E

B

30" JX3™ GAS DOWNDRAFT COOKTOP

JGD3430G – 2959⁄64" x 185⁄16" x 211⁄2"

PRODUCT DIMENSIONS

MODEL # JGD3430G

Overall width 2959⁄64 76.0

A

Overall depth 211⁄2 54.6

B

Width of cooktop base 2825⁄64 72.1

C

Width of assembled blower motor and plenum 1429⁄64 36.7

D

Height from blower motor to underside

E

of cooktop

Width from left side of cooktop base to

F

blower motor

Width from plenum to right side of cooktop base 1223⁄32 32.3

G

Height of cooktop base 49⁄64 10.5

H

Height of cooktop with grates 137⁄64 4.0

I

Height from gas inlet to top of grates 647⁄64 17.1

J

Depth of cooktop base 1961⁄64 50.7

K

Height from plenum to underside of cooktop 1649⁄64 42.6

L

TOP VIEW

E

B

A

C

I

J

H

1 of 4

in cm

185⁄16 46.5

17⁄32 3.1

F

FRONT VIEW

SIDE VIEW

D G

B

K

L

E

IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before

selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.

8991AdZw117

JENN-AIR® DETAILED PLANNING DIMENSIONSJENN-AIR® DETAILED PLANNING DIMENSIONS

E*

F

e

A

BB

v

H

G

Cabinet

I

D

C

K

J**

L

BB

M

Side

Cabinet

30" JX3™ GAS DOWNDRAFT COOKTOP

JGD3430G – 2959⁄64" x 185⁄16" x 211⁄2"

2 of 4

OPENING/CLEARANCE DIMENSIONS

MODEL # JGD3430G

A

B

C

A

D

E*

E*

F

F

G

I

H

G

v

C

e

D

H

I

J**

K

L

J**

K

M

N

v

C

FRONT VIEW

O

P

e

g

v

* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal

cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm)
stainless steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.

** Based on installation in a 24" (61.0 cm) deep by 341⁄2" (87.6 cm) high

base cabinet with a 11⁄2" (3.8 cm) thick counter top.

GAS REQUIREMENTS

Side

Cabinet

L

M

Natural Gas

This cooktop is factory-set for use with natural gas.

LP Gas Conversion

Conversion must be done by a qualified service technician. To convert to
LP gas, use the LP gas conversion kit provided with the cooktop.

ELECTRICAL REQUIREMENTS

120 volt, 60 Hz, AC only, 40-amp fused, electrical circuit is required. A
time-delay fuse or dedicated circuit is recommended.

VENTING REQUIREMENTS

This cooktop must be exhausted outdoors unless using the duct-free filter

N

M

O

P

SIDE VIEW TOP VIEW

IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before

selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved.

kit (JDA7000WX). Refer to kit instructions for further information.

LOCATION REQUIREMENTS

• To ensure cooktop base clearance, cabinet side walls need to be wider than
the cutout.

• A minimum clearance of 2" (5.1 cm) is recommended between the blower
motor and cabinet for proper cooling. A 6" (15.2 cm) clearance is recom­mended for servicing access.

• An under counter built-in oven cannot be installed under this cooktop.

in cm
Width of combustible area above
cooking surface (min.)
Width from cooktop to fixed wall or
other combustible material (min.)
Width to center of vent opening option
(min.)

30 76.2

6 15.2

77⁄8 20.0

Width to outer edge of outlet (min.) 10 25.4
Height to bottom of uncovered wood

or metal cabinet above cooking surface

30 76.2
(min.)
Height to bottom of uncovered wood
or metal cabinet (min.)
Height to center of vent opening
option

18 45.7

1411⁄16 37.3

Height to top edge of outlet (min.) 12 30.5
Height to top of gas installation area

(wall installation)

6 15.2

Depth to center of vent opening option 171⁄8 43.5
Depth of gas installation area (floor

installation)

6 15.2

Depth of upper cabinet (recommended) 13 33.0
Depth from cutout to wall (min.) 213⁄32 6.1
Width of cutout 285⁄8 72.7
Depth of cutout 1915⁄16 50.6
Depth from cutout to front of

countertop (min.)

21⁄8 5.4

Recommended electrical access location
Recommended gas supply line location
Recommended venting location –
see pages 3-4 for ducting information

8991AdZw117