Jenn-air JGCP548WP Dimension Guide
JENN-AIR® DETAILED PLANNING DIMENSIONS
A
A
B
C
D
E
A
B
C
D
E
F
G
H
A
B
C
D
E
E
F
G
A
G
I
48" PRO-STYLE® RANGETOP WITH GRIDDLE
JGCP548WP – 477⁄8" x 145⁄8" x 283⁄8"
PRODUCT DIMENSIONS
B
C
D
E
TOP VIEW
H
FRONT VIEW
F
G
1 of 2
MODEL # JGCP548WP
in cm
Overall width
A
Depth of grates/griddle
B
Depth without control panel
C
Depth with control panel
D
overhang
Depth with knobs
E
Width of grates/griddle
F
Center of rangetop to
G
center of gas inlet
Height from gas inlet
H
to cooking surface
Width of recessed rangetop
I
Height including grates/griddle
J
Height of control panel
K
Height to bullnose
L
Height of recessed rangetop
M
Height to cooking surface
N
Height of recessed rangetop
O
with grates/griddle
Depth of recessed rangetop
P
Depth with control panel
Q
477⁄8 121.6
213⁄4 55.2
231⁄4 59.0
271⁄8 68.9
283⁄8 72.0
441⁄4 112.5
195⁄8 50.0
5
14
37.1
⁄8
471⁄4 119.9
81⁄2 21.7
71⁄2 19.0
53⁄8 13.5
7 17.7
73⁄8 18.8
81⁄2 21.6
221⁄8 56.3
261⁄2 67.3
BACK VIEW
A
G
I
D
M N OLKJ
P
Q
SIDE VIEW
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8528AdZw715
JENN-AIR® DETAILED PLANNING DIMENSIONS
Side
Cabinet
D*
H
E
F
e
A
B
B
K
J
I**
C
G
Side
Cabinet
H
K
J
I**
48" PRO-STYLE® RANGETOP WITH GRIDDLE
JGCP548WP – 477⁄8" x 145⁄8" x 283⁄8"
2 of 2
OPENING/CLEARANCE DIMENSIONS
A
D*
B
F
G
e
C
FRONT VIEW
Side
Cabinet
H
I**
K
J
MODEL # JGCP548WP
in cm
Width of combustible area above cooking
A
surface (min.)
Width from rangetop to fixed wall or other
B
combustible material (min.)
Width to inner edge of outlet (max.) 16 40.6
C
Height to bottom of uncovered wood or metal
D*
cabinet above cooking surface (min.)
Height to bottom of uncovered wood or metal
E
cabinet (min.)
Height to top edge of outlet (min.) 10 25.4
F
Height to gas supply line area 14 35.6
G
Depth of upper cabinet (recommended) 13 33.0
E
B
H
Depth from cutout to wall 13⁄4 4.4
**I**
Depth of cabinet 24 61.0
J
Height from cabinet to countertop 71⁄4 18.4
K
Width of cutout (countertop and cabinet) 473⁄8 120.3
L
Width of gas opening 121⁄2 31.7
M
Width from cutout to gas opening 2 5.1
N
Width of notch
O
Zero clearance
Width of cutout (countertop only) 48 121.9
P
Zero clearance 477⁄8 121.6
Depth of gas opening 67⁄8 17.5
Q
Depth from cutout to gas opening
R
Depth of cutout (countertop and cabinet) 221⁄4 56.5
S
e
Recommended electrical outlet location
g
Recommended gas supply line location
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than 1⁄4" (0.6 cm) flame retardant millboard covered
with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless steel,
0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
If installing a hood above the rangetop, follow the hood instructions for
dimensional clearances above the cooking surface.
** If back wall is constructed of a combustible material and a backsplash is not
installed, a minimum clearance of dimension 43⁄4" (12.1 cm) is required.
48 121.9
6 15.2
42 106.7
18 45.7
5
⁄16 0.8
1
⁄4 0.6
3
⁄4 1.9
GAS REQUIREMENTS
Natural Gas
This rangetop is factory-set for use with natural gas.
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert to LP gas,
use the LP gas conversion kit provided with the rangetop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. A time-delay
fuse or dedicated circuit is recommended.
Q
M
R
N
L
I**
S
O
P
SIDE VIEW
IMPORTANT: Dimensional specifications are provided for planning purposes only.
Do not make any cutouts based on this information. Refer to the Installation Guide before
selecting cabinetry, verifying electrical/gas connections, making cutouts or beginning installation.
All Jenn-Air® appliances are appropriately UL, CUL or CSA approved. 8528AdZw715
TOP VIEW – CUTOUT
(solid platform not shown)
O
Loading...