JennAir JF42NXFXDE User Manual

JENNAIR® FRENCH DOOR
REFRIGERATOR
RÉFRIGÉRATEUR JENNAIR® AVEC
PORTEÀDOUBLE BATTANT
REFRIGERADOR DE PUERTAS
FRANCESASJENNAIR
USE AND CARE GUIDE
For questions about features, operation/performance, parts, accessories, or service,
call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.
In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.
Get the app, connect instructions, terms of use, and privacy policy at www.jennair.com/connect.
GUIDE D’UTILISATION ET D’ENTRETIEN
Pour des questions à propos des caractéristiques, du fonctionnement/rendement, des pièces, accessoires ou service,
composer le 1800JENNAIR (1800536-6247) ou visiter le www.jennair.com.
Au Canada, composer le 1800JENNAIR (1800536-6247) ou visiter le www.jennair.ca.
Obtenez l’application et les instructions de connexion, les conditions d’utilisation
et la politique de condentialité au www.jennair.com/connect.
MANUAL DE USO Y CUIDADO
Si tiene preguntas respecto a las características, funcionamiento/rendimiento, piezas, accesorios o servicio,
llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web www.jennair.com.
En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio web en www.jennair.ca.
Obtenga la aplicación, las instrucciones de conexión, los términos de uso y la política de privacidad en www.jennair.com/connect.
Table of Contents/Table des matières/Índice..........................................................................2
W11310951A
TABLE OF CONTENTS
REFRIGERATOR SAFETY ..............................................................3
Proper Disposal of Your Old Refrigerator ....................................4
BEFORE USE ..................................................................................4
Water Supply Requirements ........................................................4
Water System Preparation ...........................................................5
Install Air Filter
(on some models) .........................................................................5
Install Produce Preserver
(on some models) .........................................................................5
REFRIGERATOR USE ....................................................................6
Power On/Off Switch ...................................................................6
Using the Controls .......................................................................7
Ice Maker and Storage Bin ..........................................................8
Water Filtration System ................................................................8
REFRIGERATOR FEATURES ......................................................10
Refrigerator Shelves ...................................................................10
Deli/Crisper Drawers ..................................................................10
Wine Rack ..................................................................................10
FREEZER FEATURES ..................................................................10
Freezer Drawer and Pull-out Ice Bin ..........................................10
TABLE DES MATIÈRES
SÉCURITÉ DU RÉFRIGÉRATEUR...............................................19
Mise au rebut du vieux réfrigérateur ..........................................20
AVANT UTILISATION ....................................................................20
Spécications de l’alimentation en eau .....................................20
Préparation du circuit d’eau .......................................................21
Installer le ltre à air (sur certains modèles) ...............................21
Installer le conservateur de produits frais
(sur certains modèles) ................................................................21
UTILISATION DU RÉFRIGÉRATEUR ..........................................22
Interrupteur d’alimentation On/Off (marche/arrêt) .....................22
Utilisation des commandes .......................................................23
Machine à glaçons et bacd’entreposage .................................25
Système de ltration d’eau ........................................................25
CARACTÉRISTIQUES DU RÉFRIGÉRATEUR ...........................26
Tablettes du réfrigérateur ...........................................................26
Bacs pour spécialités alimentaires/àlégumes ..........................27
Casier à vin .................................................................................27
CARACTÉRISTIQUES DU CONGÉLATEUR ...............................27
Tiroir de congélateur et bac àglaçonscoulissant .....................27
DOOR FEATURES ........................................................................11
Utility Compartment
(on some models) .......................................................................11
Door Bins ....................................................................................11
REFRIGERATOR CARE ...............................................................11
Cleaning .....................................................................................11
Lights ..........................................................................................12
Power Interruptions ....................................................................12
Vacation Care .............................................................................12
TROUBLESHOOTING ..................................................................13
Refrigerator Operation ...............................................................13
Temperature and Moisture .........................................................14
Ice and Water .............................................................................14
ASSISTANCE OR SERVICE .........................................................15
In the U.S.A. ...............................................................................15
In Canada ...................................................................................15
ACCESSORIES .............................................................................15
PERFORMANCE DATA SHEETS .................................................16
WARRANTY ..................................................................................18
CARACTÉRISTIQUES DE LA PORTE .........................................27
Compartiment utilitaire (sur certains modèles) ..........................27
Balconnets de porte ...................................................................27
ENTRETIEN DU RÉFRIGÉRATEUR ............................................28
Nettoyage ...................................................................................28
Lampes .......................................................................................28
Pannes de courant .....................................................................28
Entretien avant les vacances .....................................................29
DÉPANNAGE .................................................................................29
Fonctionnement du réfrigérateur ...............................................29
Température et humidité ............................................................30
Glaçons et eau ...........................................................................31
ASSISTANCE OU SERVICE .........................................................32
Aux É.-U. ....................................................................................32
Au Canada ..................................................................................32
ACCESSOIRES .............................................................................32
FEUILLES DE DONNÉES SUR LA PERFORMANCE ................33
GARANTIE .....................................................................................35
SEGURIDAD DEL REFRIGERADOR ...........................................37
ÍNDICE
Cómo deshacerse adecuadamente desu refrigerador viejo ....38
ANTES DEL USO ..........................................................................38
Requisitos del suministro de agua .............................................38
Preparación del sistema de agua ..............................................39
Instalar el ltro de aire
(en algunos modelos) .................................................................39
Cómo instalar el preservador dealimentos frescos
(en algunos modelos) .................................................................39
USO DE SU REFRIGERADOR .....................................................40
Interruptor de On/Off
(Encendido/Apagado) ................................................................40
Uso de los controles ..................................................................41
Fábrica de hielo y depósito dealmacenamiento .......................42
Sistema de ltración de agua ....................................................43
CARACTERÍSTICAS DEL REFRIGERADOR .............................44
Estantes del refrigerador ............................................................44
Cajones para carnes frías/verduras ...........................................44
Portabotellas ..............................................................................45
CARACTERÍSTICAS DEL CONGELADOR .................................45
Cajón del congelador y depósito removible de hielo ................45
CARACTERÍSTICAS DE LA PUERTA .........................................45
Compartimiento de uso general
(en algunos modelos) .................................................................45
Recipientes de la puerta ............................................................45
CUIDADO DEL REFRIGERADOR ...............................................46
Limpieza .....................................................................................46
Luces ..........................................................................................46
Cortes de corriente ....................................................................46
Cuidados en período de vacaciones .........................................46
SOLUCIÓN DE PROBLEMAS......................................................47
Funcionamiento del refrigerador ................................................47
Temperatura y humedad ............................................................48
Hielo y agua ................................................................................49
ASISTENCIA O SERVICIO TÉCNICO .........................................50
En los EE.UU. .............................................................................50
En Canadá ..................................................................................50
ACCESORIOS ...............................................................................50
HOJAS DE DATOS DE RENDIMIENTO ......................................51
GARANTÍA ....................................................................................53
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
DANGER
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
follow instructions.
You
can be killed or seriously injured if you don't
instructions.
follow
WARNING:
Plug into a grounded (earthed) outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
Use nonflammable cleaner.
Do not store or use petrol, flammable liquids or gas in the
vicinity of this or other electrical appliances. The fumes can
cause fires or explosions.
Do not store explosive substances such as aerosol cans
with a flammable propellant in this refrigerator.
Do not use or place electrical devices inside the refrigerator
compartments if they are not of the type expressly
authorized by the manufacture.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker
kit ready models only).
To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
A qualified service technician must install the water line and
ice maker. See installation instruction supplied with
ice maker kit IC13B for complete details.
Connect to a potable water supply only.
Use a sturdy glass when dispensing ice (on some models).
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the appliance.
To avoid the risk of children becoming trapped and
suffocating, do not allow them to play or hide inside the
refrigerator.
If the power supply cord is damaged, it must be replaced by
the manufacturer or its service agent or a similarly qualified
person.
3
Proper Disposal of Your Old
Refrigerator
WARNING
Suffocation Hazard Remove doors from your old refrigerator. Failure to do so can result in death or brain damage.
IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous –even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow these instructions to help prevent accidents.
Before You Throw Away Your Old Refrigerator or Freezer:
■ Take off the doors.
■ Leave the shelves in place so that children may not easily
climb inside.
BEFORE USE
Important information to know about disposal of refrigerants:
Dispose of refrigerator in accordance with Federal and Local regulations. Refrigerants must be evacuated by a licensed, EPA certified refrigerant technician in accordance with established procedures.
WARNING
Excessive Weight Hazard
Use two or more people to move and install refrigerator.
Failure to do so can result in back or other injury.
Remove the Packaging
■ Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap over the adhesive with your ngers. Wipe with warm water and dry.
■ Do not use sharp instruments, rubbing alcohol, ammable
uids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your refrigerator. For more information, see “Refrigerator Safety.”
■ Dispose of/recycle all packaging materials.
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator for cleaning or service, be sure to cover the oor with cardboard or hardboard to avoid oor damage. Always pull the refrigerator straight out when moving it. Do not wiggle or “walk” the refrigerator when trying to move it, as oor damage could occur.
Clean Before Using
After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Refrigerator Care.”
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.
Water Supply Requirements
Read all directions before you begin.
IMPORTANT:
■ When your refrigerator was installed, the water connection
from the water source should have been connected to your refrigerator. If your refrigerator is not connected to a water source, see “Connect to Water Line” in the Installation Instructions. If you have any questions about your water connection, see “Troubleshooting” or call a licensed, qualied plumber.
■ If you turn the refrigerator on before the water line is
connected, turn the ice maker OFF. See “Ice Maker and Storage Bin.”
■ All installations must meet local plumbing code requirements.
4
Water Pressure
A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker.
NOTE: If the water pressure is less than what is required, the ow of water from the water dispenser could decrease or ice cubes could be hollow or irregular shaped. If you have questions about your water pressure, call a licensed, qualied plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).
If a reverse osmosis water ltration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 psi (276 kPa).
If the water pressure to the reverse osmosis system is less than 40 psi (276 kPa):
■ Check to see whether the sediment lter in the reverse
osmosis system is blocked. Replace the lter if necessary.
■ Allow the storage tank on the reverse osmosis system to rell
after heavy usage.
■ If your refrigerator has a water lter, it may further reduce
the water pressure when used in conjunction with a reverse osmosis system. Remove the water lter. See “Water Filtration System.”
If you have questions about your water pressure, call a licensed, qualied plumber.
Water System Preparation
Please read before using the water system.
IMPORTANT:
■ After connecting the refrigerator to a water source or after
replacing the water lter, ll and discard two full containers of ice to prepare the water lter for use before using the ice.
■ Connect to potable water supply only.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Install Air Filter
(on some models)
An air lter is 15 times more powerful than baking soda at reducing common food odors inside the refrigerator.
On some models, your refrigerator’s accessory packet includes an air lter which must be installed prior to use.
Installing the Air Filter
Install the air lter in the ceiling, along the back wall, of the refrigerator compartment.
1. Remove the air lter from its packaging.
2. Snap the lter into place.
Replacing the Air Filter
The disposable air lter should be replaced every 6 months. To order a replacement air lter, contact us. See “Accessories” for information on ordering.
1. Remove the used air lter by squeezing in on the side tabs.
2. Install the new air lter by snapping it into place.
Install Produce Preserver
(on some models)
The produce preserver absorbs ethylene to slow the ripening process of many produce items. As a result, certain produce items will stay fresh longer.
Ethylene production and sensitivity varies, depending on the type of fruit or vegetable. To preserve freshness, it is best to separate produce with sensitivity to ethylene from fruits that produce moderate-to-high amounts of ethylene.
1. To turn on the ice maker, simply lower the wire shutoff arm.
See “Ice Maker and Storage Bin” for further instructions on the operation of your ice maker.
NOTE: Allow 24 hours to produce the rst batch of ice.
NOTE: If your model has a base grille lter system, make sure
the base grille lter is installed so that the Eject button is out. See “Water Filtration System.”
Sensitivity
to Ethylene
Apples High Very High Asparagus Medium Very Low Berries Low Low Broccoli High Very Low Cantaloupe Medium High Carrots Low Very Low Citrus Fruit Medium Very Low Grapes Low Very Low Lettuce High Very Low Pears High Very High Spinach High Very Low
Ethylene
Production
5
Installing the Produce Preserver
A
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia, bleach or acids. Do not get in eyes, on skin or clothing. Do not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium permanganate. If swallowed, call a Poison Control Center or doctor immediately. Do not induce vomiting. If in eyes, rinse with water for 15 minutes. If on skin, rinse with water.
1. Wash the interior of a drawer with a solution of mild dish soap
and warm water and dry thoroughly.
2. Find the package containing the Produce Preserver inside the
refrigerator and install the Produce Preserver into the drawer according to the instructions provided in the package.
Replacing the Produce Preserver
The disposable packets should be replaced every 6 months or when the status indicator changes completely from white to red.
To order replacements, contact us. See “Accessories” section for information on ordering.
1. Remove the used packets from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement packets and status indicator using the
instructions included in the package.
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
Power On/Off Switch
If you need to turn the power to your refrigerator On or Off, you must remove the top grille assembly to access the power switch. Turn the power to the refrigerator Off before plugging/unplugging unit, or when cleaning your refrigerator.
To Remove Top Grille:
1. Grasp both ends of the top grille.
2. Pull the bottom out. Then, push the top grille straight up and
pull it straight out. Place the grille on a soft surface.
B BA
B BA
REFRIGERATOR USE
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
A. Top grille B. Cabinet side trims
To Replace Top Grille:
1. Insert top grille hooks (located on the back of the top grille)
onto mounting bolts on the side trim.
2. Pull the grille down slightly and push the bottom in to lock it
into place.
Turn Power On or Off:
1. Remove top grille.
2. Press power switch to the On or Off position.
3. Replace top grille. IMPORTANT: Be sure the power switch is set to the On position
after cleaning refrigerator.
A. Power switch
6
Using the Controls
IMPORTANT:
■ The Fridge control adjusts the temperature in the refrigerator
compartment. The Freezer control adjusts the temperature in the freezer compartment.
■ Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the temperature controls to a lower (colder) setting will not cool the compartments any faster.
■ If the temperature is too warm or too cold in the refrigerator
or freezer, rst check the air vents to be sure they are not blocked before adjusting the controls.
■ The recommended settings should be correct for normal
household usage. The controls are set correctly when milk or juice is as cold as you like and when ice cream is rm.
■ The actual temperature may differ from the display when a
door is open for an extended period of time.
Turning On Cooling and Viewing Set Points
The factory recommended set points are 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator
1. Press the FRIDGE or FREEZER touch pad. NOTE: After the refrigerator is turned on, the Over
Temperature audio alarm and indicator light may activate every 1½ hours until the refrigerator and freezer temperatures are below 48°F (9°C) and 15°F (-9°C), respectively, or until the alarm is turned off. To turn off the audio alarm and indicator light, see “Alarm Reset.”
Adjusting Controls
NOTE: Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.
To Adjust Set Point Temperatures:
■ Press the FRIDGE or FREEZER touch pad, and then press the
Plus (+) or Minus (-) touch pad until the desired temperature is reached.
■ Press the SAVE touch pad to program the desired
temperature.
NOTE: The set point range for the freezer is -5°F to 3°F (-21°C to -16°C). The set point range for the refrigerator is 34°F to 42°F
(1°C to 6°C).
CONDITION /REASON:: TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold Not set correctly for conditions
REFRIGERATOR too warm High use or room very warm
FREEZER too cold
REFRIGERATOR Control 1° higher
REFRIGERATOR Control 1° lower
FREEZER Control1° higher
Not set correctly for conditions FREEZER too warm/too little
FREEZER Control 1° lower ice High use or heavy ice use
Options
Turning Off Cooling
1. Press the FRIDGE or FREEZER touch pad.
2. Press and hold the COOLING OFF touch pad for 3 seconds. NOTE: To turn off the power completely, use the power
ON/ OFF switch located behind the top grille. See “Power On/ Off Switch.”
Viewing the Temperature in Degrees Celsius
1. Press °C touch pad. To display degrees Fahrenheit, press °F touch pad.
NOTE: If the freezer temperature is below zero, the negative sign next to the freezer display will light up. This is normal.
Max Ice
The Max Ice feature speeds up the ice production rate to assist with periods of heavy ice usage.
■ Press OPTIONS, and then press MAX ICE to turn on the Max
Ice feature. Max Ice will remain activated for 24 hours unless manually turned off.
NOTE: The temperature display for the refrigerator and freezer compartments will remain at the user’s set points, but the actual temperature of the freezer compartment will drop to -5°F (-21°C), while the Max Ice feature is enabled. After 24 hours, the freezer will return to the previous temperature set point.
Max Cool
The Max Cool feature assists with full grocery loads, temporarily warm room temperatures, or during heavy door opening use.
■ Press OPTIONS, and then press MAX COOL to turn on the
Max Cool feature. Max Cool will remain activated for 24 hours unless manually turned off.
NOTE: The temperature display for the refrigerator compartment will remain at the user’s set point, but the actual temperature of the refrigerator compartment will drop to 34°F (1°C), while the Max Cool feature is enabled. After 24 hours, the refrigerator returns to the previous temperature set points.
7
Sabbath Mode
Sabbath mode is designed for the traveler or for those whose religious observances require turning off the lights and ice maker. By selecting this feature, the temperature set points remain unchanged, the ice maker will be disabled, the interior lights will turn off, and the audio tones are muted. For most efcient refrigerator operation, it is recommended to exit Sabbath mode when it is no longer required.
■ Press the SABBATH touch pad to turn on Sabbath mode. This
feature will remain on until Sabbath is pressed again.
NOTE: If the Max Cool or Max Ice feature has been selected prior to turning on Sabbath mode, Max Cool and Max Ice will be automatically canceled upon entering Sabbath mode.
Filter Reset
See “Water Filter Indicator” in the “Water Filtration System” section.
Alarm Functions
Alarm Reset
Pressing any Home Screen touch pad (Fridge, Freezer or Options) will turn off the audio alarm and indicator light. The audio alarm will not sound again for the current condition that caused the alarm until a new condition occurs.
An Alarm Reset can be performed by pressing any Home Screen touch pad (Fridge, Freezer or Options), or by turning the power to the refrigerator off and on again. See “Power On/Off Switch.” After performing an Alarm Reset, the indicator light will reactivate if the condition that caused the alarm is still present. See “Door Open,” “Over Temperature” or “Power Outage.”
Door Open
An alarm will sound when a door has been open for longer than 5 minutes. Closing the door or drawer, or pressing any Home Screen touch pad (Fridge, Freezer or Options) will reset the Door Open feature and turn off the audio alarm.
NOTE: If the door(s) or drawer are left open for 10 minutes the interior lights will go out. Closing the open door(s) or drawer will reset the lights.
Over Temperature
IMPORTANT: If the Over Temperature Alarm activates, your food may spoil. See “Power Interruptions.” Minimize door openings until temperatures return to normal.
The Over Temperature feature is designed to let you know when either the refrigerator temperature rises above 48°F (9°C) or the freezer temperature rises above 15°F (-9°C) for longer than 1½ hours. The audio alarm will shut off automatically when the temperature returns to normal, but the indicator light will continue to ash to let you know that an Over Temperature condition occurred until an Over Temperature reset has been performed. Press any Home Screen touch pad (Fridge, Freezer or Options) to turn off the indicator light.
If the over temperature condition is still present when an Over Temperature reset is performed, the indicator light will continue to reactivate every 1½ hours until refrigerator and freezer temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.
Power Outage
When a power outage occurs, a Power Outage indicator light will be displayed. Press any Home Screen touch pad (Fridge, Freezer or Options) to turn off the indicator light. The power outage indicator light will not display when either Cooling Off or Sabbath mode is active, but will appear after exiting Sabbath mode if a power outage occurred.
Ice Maker and Storage Bin
IMPORTANT: After connecting the refrigerator to a water source
or replacing the water lter, ll and discard two full containers of ice to prepare the water lter for use, before using the ice.
Turn the Ice Maker On/Off
1. To turn ON the ice maker, simply lower the wire shutoff arm. NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will ll the ice storage bin and the ice cubes will raise the wire shutoff arm to the OFF (arm up) position. Do not force the wire shutoff arm up or down.
2. To manually turn off the ice maker, lift the wire shutoff arm to the OFF (arm up) position and listen for the click.
Ice Storage Bin Care
NOTE: It is normal for ice to stick together in the ice bin. It is recommended that the ice bin be emptied and cleaned as needed.
To clean the ice storage bin:
1. Slide the ice bin out of the freezer, and then lift up and out.
2. Empty the ice bin. Use warm water to melt the ice if
necessary. NOTE: Do not use anything sharp to break up the ice in the
bin. This can cause damage to the ice bin and the dispenser mechanism.
3. Wash ice bin with warm water and a mild detergent, rinse well and dry thoroughly. Do not use harsh or abrasive cleaners or solvents.
REMEMBER:
■ Allow 24 hours to produce the rst batch of ice.
■ It may take 3 to 4 days for the ice bin to completely ll, if no
ice is used.
■ The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.
■ Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of the ice maker and lead to poor quality ice. If a softened water supply cannot be avoided, make sure the water softener is operating properly and is well maintained.
■ It is normal for the ice cubes to be attached at the corners.
They will break apart easily.
■ Do not store anything inside the ice bin.
Water Filtration System
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
8
Water Filter Indicator (on some models)
B
The water lter indicator, located on the control panel, will help you know when to change the water lter.
A replacement water lter should be ordered when “Order Filter” is displayed. It is recommended that you replace the lter when “Replace Filter” is displayed or when water ow to your water dispenser and/or ice maker decreases noticeably. See “Changing the Water Filter” later in this section.
After changing the water lter, press and hold FILTER RESET for 3 seconds until the “Order Filter” or “Replace Filter” indicator light disappears.
Changing the Water Filter
The water lter is located in the base grille below the freezer compartment door. It is not necessary to remove the base grille to remove the lter.
1. Remove the lter by pressing the eject button and pulling
straight out on the lter cap.
NOTES:
■ Avoid twisting the cap when removing the lter because
this could cause the cap to come off. If this occurs, replace the cap and pull the lter straight out.
■ There will be water in the lter. Some spilling may occur.
A
5. Place the cap (removed in Step 2) on the new lter. Align the ridge on the cap with the arrow on the lter. Turn the cap clockwise until it snaps into place.
B
C
A
A. Eject button B. Arrow on lter C. Ridge on cap
6. Push the new lter into the opening in the base grille. As the lter is inserted, the eject button will depress. The eject button will pop back out when the lter is fully engaged.
7. Pull gently on the cap to check that the lter is securely in place.
8. Flush the water system. Depending on your model, see “Water and Ice Dispensers” or “Ice Maker and Storage Bin.”
A. Eject button B. Filter cap
2. Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your
refrigerator. Keep the cap to use with the replacement lter.
3. Align the ridge on the cap with the arrow on the new lter, and then turn the cap until it snaps into place.
A B
A. Cover B. O-rings
4. Remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
Using the Ice Maker Without a Water Filter
You can operate the ice maker without a water lter. Your ice will not be ltered.
1. Remove the lter by pressing the eject button and pulling on
the cap. See “Changing the Water Filter” earlier in this section.
2. Remove the cap by turning it counterclockwise until it stops. IMPORTANT: Do not discard the cap. It is part of your
refrigerator.
3. With the cap in a horizontal position, insert the cap into the base grille until it stops.
4. Turn the cap counterclockwise until the cap slips into the attachment slot. Then, turn the cap clockwise until it is in a horizontal position.
NOTE: The cap will not be even with the base grille.
9
REFRIGERATOR FEATURES
Refrigerator Shelves
2. To replace the deli/crisper drawer, pull out the drawer slides
until they are fully extended and set the drawer on the slides. Push the drawer in toward the back until it is in closed position.
3. Reopen the deli/crisper drawer to make sure it has been replaced properly.
Important information to know about glass shelves and covers:
Do not clean glass shelves or covers with warm water when they are cold. Shelves and covers may break if exposed to sudden temperature changes or impact, such as bumping. Tempered glass is designed to shatter into many small, pebble-size pieces. This is normal. Glass shelves and covers are heavy. Use both hands when removing them to avoid dropping.
The shelves in your refrigerator are adjustable to match your individual storage needs.
Storing similar food items together in your refrigerator and adjusting the shelves to t different heights of items will make nding the exact item you want easier. It will also reduce the amount of time the refrigerator door is open, and save energy.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
1. Remove the shelf by tilting it up at the front and lifting it out of
the shelf supports. Pull shelf straight out.
2. Reposition the shelf supports in the desired location. Check
that they are level and rmly inserted in the support rails.
3. Place the back of the shelf in the shelf supports.
4. Lower the front of the shelf and make sure that it is in
position.
Wine Rack
To remove and replace the wine rack:
1. Remove the rack by pulling it straight out from the shelf.
2. Replace the rack by sliding it in between the shelf and the wall
of the refrigerator.
FREEZER FEATURES
Freezer Drawer and Pull-out Ice Bin
The freezer drawer can be used to store smaller items. The freezer drawer is not removable.
To remove and replace the ice bin:
1. Slide the ice bin out of the freezer, and then lift up and out.
Meat Storage Guide
Store most meat in original wrapping as long as it is airtight and moisture-proof. Rewrap if necessary. See the following chart for storage times. When storing meat longer than the times given, freeze the meat.
Fresh sh or shellsh......................... use same day as purchased
Chicken, ground beef, variety meats (liver) ...................... 1-2 days
Cold cuts, steaks/roasts .................................................. 3-5 days
Cured meats................................................................... 7-10 days
Leftovers - Cover leftovers with plastic wrap, aluminum foil, or plastic containers with tight lids.
Deli/Crisper Drawers
To remove and replace the deli/crisper drawers:
1. Slide the deli/crisper drawer straight out to the stop. Lift the
front of the drawer with one hand while supporting the bottom with the other hand. Slide the drawer out the rest of the way.
10
A
B
A. Ice bin B. Freezer drawer
2. To replace the ice bin, pull out the drawer slides until they are fully extended, and then set ice bin on the slides. Push the ice bin in toward the back until it is in closed position.
3. Reopen the ice bin to make sure it has been replaced properly.
Frozen Food Storage Guide
Storage times will vary according to the quality and type of food, the type of packaging or wrap used (should be airtight and moisture-proof), and the storage temperature. Ice crystals inside a sealed package are normal. This simply means that moisture in the food and air inside the package have condensed, creating ice crystals.
Put no more unfrozen food into the freezer than will freeze within 24 hours (no more than 2 to 3 lbs of food per cubic foot [907­1,350 g per 28 L] of freezer space). Leave enough space in the freezer for air to circulate around packages. Be sure to leave enough room for the door to close tightly.
For more information on preparing food for freezing, check a freezer guide or reliable cookbook.
DOOR FEATURES
REFRIGERATOR CARE
Utility Compartment
(on some models)
The utility compartment can be placed in any position on the refrigerator door.
To remove and replace the utility bin:
1. Remove utility compartment by grasping both ends and lifting
compartment up and out.
2. Replace the bin by sliding it in above the desired support and
pushing it down until it stops.
Door Bins
Large door bins hold gallon containers and the smaller door bins hold 2-liter bottles. The door bins are adjustable and removable for easy cleaning and adjusting.
Gallon Door Bin
To install the gallon door bin: NOTE: The gallon door bin can only be placed on the lower door
support.
1. Position gallon door bin above lowest door adjustment slot.
2. Push down to secure bin.
3. Adjust other bins, as necessary to allow for milk or beverage
container height.
Door Bins
To remove and replace the door bins:
1. Remove the bin by lifting it up and pulling it out.
2. Replace the bin by sliding it in above the desired support and
pushing it down until it stops.
Cleaning
WARNING
Explosion Hazard Use nonammable cleaner. Failure to do so can result in death, explosion, or re.
Both the refrigerator and freezer sections defrost automatically. However, clean both sections about once a month to avoid buildup of odors. Wipe up spills immediately.
To Clean Your Refrigerator:
1. Remove the top grille. See “Power On/Off Switch.”
2. Press the power switch to OFF.
3. Remove all removable parts from inside, such as shelves,
crispers, etc.
4. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a mild detergent in warm water.
■ Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, ammable uids, cleaning waxes, concentrated detergents, bleaches or cleansers containing petroleum products on plastic parts, interior and door liners or gaskets. Do not use paper towels, scouring pads, or other harsh cleaning tools. These can scratch or damage materials.
■ To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt [26 g to 0.95 L] of water).
5. Clean the exterior surfaces. Stainless steel panels: Wash stainless steel with a clean
sponge or soft cloth and a mild detergent in warm water.
■ To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that you use the manufacturer’s approved Stainless Steel Cleaner and Polish.
IMPORTANT: This cleaner is for stainless steel parts only! Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces, dispenser covers or door gaskets. If unintentional contact does occur, clean plastic part with a sponge and mild detergent in warm water. Dry thoroughly with a soft cloth. To order the cleaner, see “Accessories.”
6. Press the power switch to ON.
7. Replace the top grille. See “Power On/Off Switch.”
11
Lights
The lights in both the refrigerator and freezer compartments are LEDs which do not need to be replaced. If the lights do not illuminate when the door or drawer is opened, call for assistance or service. In the U.S.A., call 1-800-JENNAIR (1-800-536-6247). In Canada call 1-800-JENNAIR (1-800-536-6247).
Power Interruptions
If the power will be out for 24 hours or less, keep the door or doors closed (depending on your model) to help food stay cold and frozen.
If the power will be out for more than 24 hours, do one of the following:
■ Remove all frozen food and store it in a frozen food locker.
■ Place 2 lbs (907 g) of dry ice in the freezer for every cubic foot
(28 L) of freezer space. This will keep the food frozen for 2 to 4 days.
■ If neither a food locker nor dry ice is available, consume or
can perishable food at once.
REMEMBER: A full freezer stays cold longer than a partially lled one. A freezer full of meat stays cold longer than a freezer full of baked goods. If you see that food contains ice crystals, it may be refrozen, although the quality and avor may be affected. If the condition of the food is poor, dispose of it.
Vacation Care
Your refrigerator is equipped with the Sabbath mode feature, which is designed for the traveler or for those whose religious observances require turning off the lights and ice maker. By selecting this feature, the temperature set points remain unchanged, the ice maker will be disabled and the interior lights will turn off. For most efcient refrigerator operation, it is recommended to exit Sabbath mode when it is no longer required.
If You Choose to Leave the Refrigerator On While You’re Away:
1. Use up any perishables and freeze other items.
2. Press the SABBATH touch pad.
3. If your refrigerator has an automatic ice maker, shut off the
water supply to the ice maker.
4. Empty the ice bin.
5. When you return from vacation, press the SABBATH touch
pad to return to normal operation.
If You Choose to Turn Off the Refrigerator Before You Leave:
1. Remove all food from the refrigerator.
2. If your refrigerator has an automatic ice maker:
■ Turn off the water supply to the ice maker at least one day
ahead of time.
■ When the last load of ice drops, raise the wire shutoff arm
to the OFF (up) position.
3. Under the Fridge or Freezer menu, press and hold COOLING OFF for 3 seconds to turn off cooling.
NOTE: To turn off the power completely, use the power ON/ OFF switch located behind the top grille. See “Power On/Off Switch.”
4. Clean refrigerator, wipe it, and dry well.
5. Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and mold from building up.
When you get to your new home, put everything back and refer to the “Installation Instructions” section for preparation instructions. Also, if your refrigerator has an automatic ice maker, remember to reconnect the water supply to the refrigerator.
12
TROUBLESHOOTING
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call, refer to the warranty page in this manual, visit http://producthelp.jennair.com or call 1-800-JENNAIR (1-800-536-6247). In Canada, visit www.jennair.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.: JennAir Brand Home Appliances
Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Refrigerator Operation
The refrigerator will not operate
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death, fire, or electrical shock.
In Canada: JennAir Brand Home Appliances
Customer eXperience Centre 200 – 6750 Century Ave. Mississauga, Ontario L5N 0B7
The refrigerator seems noisy
Refrigerator noise has been reduced over the years. Due to this reduction, you may hear intermittent noises from your new refrigerator that you did not notice from your old model. Below are listed some normal sounds with explanations.
Buzzing - heard when the water valve opens to ll the ice
maker.
Pulsating - fans/compressor adjusting to optimize
performance.
Hissing/Rattling - ow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator.
Sizzling/Gurgling - water dripping on the heater during
defrost cycle.
Popping - contraction/expansion of inside walls, especially
during initial cool-down.
Water running - may be heard when ice melts during the
defrost cycle and water runs into the drain pan.
Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.
■ Power cord unplugged? Plug into a grounded 3 prong outlet.
■ Is outlet working? Plug in a lamp to see if the outlet is
working.
Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues, call an electrician.
Are controls on? Make sure the refrigerator controls are on.
See “Using the Control(s).”
New installation? Allow 24 hours following installation for the
refrigerator to cool completely. NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its high-efciency compressor and fans. The unit may run even longer if the room is warm, a large food load is added, doors are opened often, or if the doors have been left open.
There is no audible door open alarm
Has the door been open less than 5 minutes? The door open alarm will only ash when the door has been open for 5 minutes. The audible alarm will sound the rst time the door is left open for more than 5 minutes. Subsequent door open alarms will only ash. You must reset the audible alarm each time. See “Using the Control(s).”
The doors will not close completely
■ Door blocked open? Move food packages away from door.
■ Bin or shelf in the way? Push bin or shelf back in the correct
position.
13
The doors are difficult to open
WARNING
Explosion Hazard Use nonammable cleaner. Failure to do so can result in death, explosion, or re.
Are the gaskets dirty or sticky? Clean gaskets and contact
surfaces with mild soap and warm water. Rinse and dry with soft cloth.
The lights do not work
Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice production.
Freezer door closed completely? Firmly close the freezer
compartment door. If the freezer compartment door will not close all the way, see “The doors will not close completely,” earlier in this section.
Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
Water lter installed on the refrigerator? Remove lter and
operate ice maker. If ice volume improves, then the lter may be clogged or incorrectly installed. Replace lter or reinstall it correctly.
■ Reverse osmosis water ltration system connected to
your cold water supply? This can decrease water pressure.
See “Water Supply Requirements.”
Is the refrigerator in Sabbath mode? See “Using the
Controls.”
Has the door been open more than 10 minutes? See
“Using the Controls.”
Temperature and Moisture
Temperature is too warm
New installation? Allow 24 hours following installation for the
refrigerator to cool completely.
Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully closed.
Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in 24 hours. See “Using the Control(s).”
Refrigerator not cooling? For models with digital controls,
turn the refrigerator OFF and then ON to reset. If this does not correct the problem, call for service.
Air vents blocked? Remove any item from in front of the air
vents.
The ice cubes are hollow or small
NOTE: This is an indication of low water pressure.
■ Water shutoff valve not fully open? Turn the water shutoff
valve fully open.
Kink in the water source line? A kink in the line can reduce
water ow. Straighten the water source line.
Water lter installed on the refrigerator? Remove lter and
operate ice maker. If ice quality improves, then the lter may be clogged or incorrectly installed. Replace lter or reinstall it correctly.
■ Reverse osmosis water ltration system connected to
your cold water supply? This can decrease water pressure.
See “Water Supply Requirements.”
Questions remain regarding water pressure? Call a
licensed, qualied plumber.
Ice is sticking together in the ice storage bin
■ It is normal for frost to be on top of the ice storage bin due to
normal opening and closing of the freezer.
■ It is normal for ice to stick together when it is not dispensed
or used frequently. It is recommended that the ice storage bin be emptied and cleaned as needed. See “Ice Maker and Storage Bin.”
There is interior moisture buildup
NOTE: Some moisture buildup is normal.
■ Humid room? Contributes to moisture buildup.
■ Door(s) opened often or left open? Allows humid air to enter
refrigerator. Minimize door openings and keep doors fully closed.
Ice and Water
The ice maker is not producing ice or not enough ice
■ Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source line? A kink in the line can reduce
water ow. Straighten the water source line.
14
Off-taste, odor or gray color in the ice
New plumbing connections? New plumbing connections
can cause discolored or off-avored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow 24
hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture proof
packaging to store food.
Are there minerals (such as sulfur) in the water? A water
lter may need to be installed to remove the minerals.
Is there a water lter installed on the refrigerator? Gray
or dark discoloration in ice indicates that the water ltration system needs additional ushing.
ASSISTANCE OR SERVICE
If You Need Service
Please refer to the warranty page in this manual.
If You Need Replacement Parts
If you need to order replacement parts, we recommend that you use only factory specied parts. Factory specied parts will t right and work right because they are made with the same precision used to build every new JennAir® appliance.
To locate factory specied parts in your area, call us or your nearest designated service center.
In the U.S.A.
Call the JennAir Customer eXperience Center toll free
1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.com.
Our consultants provide assistance with:
■ Features and specications on our full line of appliances.
■ Referrals to local JennAir brand dealers.
■ Installation information.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
■ Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
For Further Assistance
If you need further assistance, you can write to JennAir with any questions or concerns at:
JennAir Brand Home Appliances Customer eXperience Center 553 Benson Road Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada
Call the JennAir Canada LP Customer eXperience Centre toll free
1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.
Our consultants provide assistance with:
■ Scheduling of service. JennAir
technicians are trained to fulll the product warranty and provide after-warranty service, anywhere in Canada.
■ Features and specications on our full line of appliances.
■ Referrals to local JennAir brand dealers.
■ Use and maintenance procedures.
■ Accessory and repair parts sales.
For Further Assistance
If you need further assistance, you can write to JennAir Canada LP with any questions or concerns at:
JennAir Brand Home Appliances Customer eXperience Centre 200 – 6750 Century Ave. Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
®
appliances designated service
ACCESSORIES
The following accessories are available for your refrigerator. To order an accessory, contact us and ask for the part number.
In the U.S.A., visit our website www.jennair.com/accessories or call 1-800-JENNAIR (1-800-536-6247).
In Canada, visit our webpage www.jennair.ca or call
1-800-JENNAIR (1-800-536-6247). Affresh® Stainless Steel Cleaner:
In U.S.A., order Part #W10355016 In Canada, order Part #W10355016B
Affresh® Stainless Steel Wipes:
In U.S.A., order Part #W10355049 In Canada, order Part #W10355049B
Affresh® Kitchen & Appliance Cleaner:
In U.S.A., order Part #W10355010 In Canada, order Part #W10355010B
Replacement Water Filter:
In U.S.A., order Part #4396841 (T2RFWG2) In Canada, order Part #4396841B (T2RFWG2)
Air Filter: Order Part #W10311524
Produce Preserver Keep Fresh Packet Rell: Order Part #P1KC6R1
15
PERFORMANCE DATA SHEETS
Base Grille Water Filtration System
Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)
Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)
System tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.
Substance Reduction Aesthetic Effects
Chlorine Taste/Odor Particulate Class II*
Contaminant Reduction
Lead: @ pH 6.5 *** Lead: @ pH 8.5 ***
Mercury: @ pH 6.5 Mercury: @ pH 8.5
Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 0.0006 mg/L 92.22% 96.34% O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58% 99.63% Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.001 mg/L 93.3% 93.3% Carbofuran 0.040 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L 0.0213 mg/ 51.13% 74.00%
NSF
Reduction
Requirements
50% reduction
85% reduction
NSF Reduction
Requirements
0.010 mg/L
0.010 mg/L
0.002 mg/L
0.002 mg/L
Average Inuent
2.0182 mg/L 1333333 #/mL
Average Inuent
0.1533 mg/L
0.1400 mg/L
0.0058 mg/L
0.0059 mg/L
Inuent Challenge Concentration
2.0 mg/L ± 10% At least 10,000 particles/mL
Inuent Challenge Concentration
0.15 mg/L ± 10%
0.15 mg/L ± 10%
0.006 mg/L ± 10%
0.006 mg/L ± 10%
Maximum Efuent
0.06 mg/L 6600 #/mL**
Maximum Efuent
0.0005 mg/L
0.0007 mg/L
0.0002 mg/L
0.0005 mg/L
Average Efuent
0.0536 mg/L 2325 #/mL
Average Efuent
0.0005 mg/L
0.0006 mg/L
0.0002 mg/L
0.0003 mg/L
Minimum% Reduction
97.03%
99.51%
Minimum% Reduction
99.67%
99.50%
96.54%
91.57%
Average% Reduction
97.34%
99.83%
Average% Reduction
99.67%
99.57%
96.54%
94.92%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
■ It is essential that operational, maintenance, and lter
replacement requirements be carried out for the product to perform as advertised.
■ Use replacement lter T2RFWG2, part #4396841.
Model T1WG2L: Style 1 – When the lter indicator reads 10%, order a new lter. When the indicator reads 0%, it is recommended that you replace the lter.
Style 2 – When the lter indicator changes from green to yellow, order a new lter. When the indicator changes from yellow to red, it is recommended that you replace the lter.
Style 3 – When the water lter status display changes from “GOOD” to “ORDER,” order a new lter. When the lter indicator reads “REPLACE,” it is recommended that you replace the lter.
Style 4 – Press FILTER to check the status of your water lter. If the lter indicator light is yellow, order a new lter. If the lter indicator light is red, it is recommended that you replace the lter.
■ These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory conditions, actual performance may vary.
■ The product is for cold water use only.
■ Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
■ Refer to the “Warranty” section for the Manufacturer’s name,
address and telephone number.
■ Refer to the “Warranty” section for the Manufacturer’s limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply Water Pressure Water Temperature Service Flow Rate
City or Well 35 - 120 psi (241 - 827 kPa) 33° - 100°F (1° - 38°C)
0.85 gpm (3.2 L/min.) @ 60 psi*
Model T1WG2: Change the water lter cartridge every 6 months. If the water ow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water lter cartridge more often.
*Class II particle size: 1 um to <5 um **Test requirement is at least 100,000 particles/mL of AC Fine Test Dus ***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.
®
NSF is a registered trademark of NSF International.
16
Base Grille Water Filtration System
Model T1WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)
Model T1WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)
System tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor, Particulate Class II*; and against NSF/ANSI Standard 53 for the reduction of Mercury, Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specied in NSF/ANSI Standards 42 and 53.
Substance Reduction Aesthetic Effects
Chlorine Taste/Odor Particulate Class II*
Contaminant Reduction
Lead: @ pH 6.5 *** Lead: @ pH 8.5 ***
Mercury: @ pH 6.5 Mercury: @ pH 8.5
Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L ± 10% 0.0012 mg/L 0.0006 mg/L 92.22% 96.34% O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L ± 10% 0.0250 mg/L 0.0066 mg/L 98.58% 99.63% Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L ± 10% 0.001 mg/L 0.001 mg/L 93.3% 93.3% Carbofuran 0.040 mg/L 0.0819 mg/L 0.08 mg/L ± 10% 0.0400 mg/L 0.0213 mg/ 51.13% 74.00%
NSF
Reduction
Requirements
50% reduction
85% reduction
NSF Reduction
Requirements
0.010 mg/L
0.010 mg/L
0.002 mg/L
0.002 mg/L
Average Inuent
2.0182 mg/L 1333333 #/mL
Average Inuent
0.1533 mg/L
0.1400 mg/L
0.0058 mg/L
0.0059 mg/L
Inuent Challenge Concentration
2.0 mg/L ± 10% At least 10,000 particles/mL
Inuent Challenge Concentration
0.15 mg/L ± 10%
0.15 mg/L ± 10%
0.006 mg/L ± 10%
0.006 mg/L ± 10%
Maximum Efuent
0.06 mg/L 6600 #/mL**
Maximum Efuent
0.0005 mg/L
0.0007 mg/L
0.0002 mg/L
0.0005 mg/L
Average Efuent
0.0536 mg/L 2325 #/mL
Average Efuent
0.0005 mg/L
0.0006 mg/L
0.0002 mg/L
0.0003 mg/L
Minimum% Reduction
97.03%
99.51%
Minimum% Reduction
99.67%
99.50%
96.54%
91.57%
Average% Reduction
97.34%
99.83%
Average% Reduction
99.67%
99.57%
96.54%
94.92%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).
■ It is essential that operational, maintenance, and lter
replacement requirements be carried out for the product to perform as advertised.
■ Use replacement lter T2RFWG2, part #4396841.
Model T1WG2L: Style 1 – When the lter indicator reads 10%, order a new lter. When the indicator reads 0%, it is recommended that you replace the lter.
Style 2 – When the lter indicator changes from green to yellow, order a new lter. When the indicator changes from yellow to red, it is recommended that you replace the lter.
Style 3 – When the water lter status display changes from “GOOD” to “ORDER,” order a new lter. When the lter indicator reads “REPLACE,” it is recommended that you replace the lter.
Style 4 – Press FILTER to check the status of your water lter. If the lter indicator light is yellow, order a new lter. If the lter
■ The product is for cold water use only.
■ Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system.
■ Refer to the “Warranty” section for the Manufacturer’s name,
address and telephone number.
■ Refer to the “Warranty” section for the Manufacturer’s limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply Water Pressure Water Temperature Service Flow Rate
City or Well 35 - 120 psi (241 - 827 kPa) 33° - 100°F (1° - 38°C)
0.5 gpm (1.9 L/min.) @ 60 psi*
indicator light is red, it is recommended that you replace the lter.
Model T1WG2: Change the water lter cartridge every 6 months. If the water ow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water lter cartridge more often.
■ These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory conditions, actual performance may vary.
*Class II particle size: 1 um to <5 um **Test requirement is at least 100,000 particles/mL of AC Fine Test Dus ***Compliant for Lead reduction requirements under NSF/ANSI Standard 53 as tested by Pace Analytical Services, Inc.
®
NSF is a registered trademark of NSF International.
17
Loading...
+ 37 hidden pages